USB-6009 device not found problem

Hello all,
So my VI and USB-6009 have been working fine until recently. I noticed the VI was not reading or graphing information from the analog input channel correctly. My firmware is up to date, but I noticed a problem. In Isdaq, it will recognize that the USB-6009 is connected, then when I run my VI and stop it, i check Isdaq for my device again, and it does not recognize any device. I have to unplug the daq and replug it for Isdaq to recognize the usb-6009 again. But each time I run my VI, it does not seem to collect any data, and it makes the device unrecognizable. Do you know what the problem might be? Attached is the VI I have been running in case you want to look at it. Its been working fine until now.
btw, I am running Labview on a Mac OS X
Thanks for the help!
Solved!
Go to Solution.
Attachments:
AO:AI Data Aquisition.vi ‏39 KB

Hello Solis,
I would recommend making changes to the parallel tasks to use the error cluster to force the order of execution, since NI-DAQmx Base is not multi-thread safe (review NI-DAQmx Readme). Please verify if this alleviates the issue.
Best regards,
Ali M
Applications Engineer
National Instruments
www.ni.com/support

Similar Messages

In-built Audio device not found

Hi Guys,
My macbook pro suddenly finds no audio device inbuilt. And i can play no sound nor hear start up sound when switching on mac.
I get a 'no parking' like symbol beneath my audio options.
I've tried rebooting in safe mode, Resetting PRAM, Repairing permissions in disk utilities, use my ipod touch headsets, headphones.. NOthing worked.
And i'm feeling deaf whenever using Mac now.
Is there anyway to get the audio back ?
Thanks,
Raesh

Hmm.. Okay. Would give it a last try.
And I have a couple question before doing that..
1. I did the hardware test and It gave me this error .. " 4SNS/1/C0000008 :TPCD--24 "
But When i looked up for this error, it tells me a sensor problem. Not as Audio device problem. Do you think this hardware error of 'sensor' has something to do with audio ?
2. So in-built speaker isn't working, plugging in headphones cable isn't working. But i was wondering whether a bluetooth speaker would be recoganised in the system preferences > audio output device ? Will it work ?
Because i keep on reading that an " in-built audio device not found " problem is a huge one and it costs a lot to repair. They often provide solution of changing the whole logic board (Keeping fingers crossed). And with my warranty period over, I don't wish to go through that path. So want to know if external bluetooth speaker has a chance to get recoganised as an audio device, Then I would buy JBL bluetooth speakers. It seems good and less pricey than changing the whole logic board.
Let me know which way i can go, Thanks in Advance Man.
// Raesh.S

Usb - 6009 Device Recongition Problems

Hi,
I just got a USB-6009 DAQ. I have labview 7.0, drivers software and the supplied software installed with no problems. In the measurment nad automation explorer (MAX) the device is recongnised and declared problem free. I tried to test the device in labview using help tutorials which suggests the DAQ assitant block. After selecting Analogue input and then voltage I am told that no device is detected i.e. Where I should be selecting my terminal(s) I am not giving any options.
If anyone has had the same problems or know how to fix them I would be thankful of your help.
Kyle

Hi Kyle,
The USB-6009 device works on DAQmx base. This is a restricted version of NI-DAQmx which is used on some of our products. Unfortunetly it is incompatible with DAQmx and the DAQ Assistant uses DAQmx. Therefore you can't use the UDB-6009 with the DAQ Assistant.
To use the device, load up the USB-600x Interactive Control which should be located in the following directory.
C:\Program Files\National Instruments\LabVIEW 7.0\examples\daqmxbase
Take a look at this and figure out how the code works. If you want to configure it to do your own specific functions then I would suggest that you use this program as a base and customise it for your purposes.
Best regards,
Peter H.
Applications Engineer.
NIUK.

Start-up problem with hp pavilion dv6t-7000‏: "Boot Device Not Found. Hard Disk (3F0)" error

I started getting start-up problems with my hp pavilion dv6t-7000‏. It happens intermittently.
The boot error is:
Boot Device Not Found
   Please install an operating system on your hard disk.
   Hard Disk (3F0)
   F2 System Diagnostics
   For more information, please visit: www.hp.com/go/techcenter/startup
Could a faulty BIOS update cause this problem?
Anyone else who may have experienced a similar problem?
I'd appreciate any help about this problem. Thanks.

Hi
Please find the link given below might help you to fix your issue.
Resolve Boot Device not Found Error Message
Let us know how it goes!
"I work for HP."
****Click the (purple thumbs up icon in the lower right corner of a post) to say thanks****
****Please mark Accept As Solution if it solves your problem****
Regards
Manjunath

I AM UNABLE TO UNLOCK MY PHONE AS IT GOT DISABLED AFTER TYPING INCORRECT PASSCODE.IF I CONNECT MY PHONE TO ITUNES IT SAYS USB DEVICE NOT FOUND.

AFTER TYPING INCORRECT PASSCODE MULTIPLE TIMES MY PHONE GOT DISABLED. IT SAYS CONNECT TO ITUNES BUT ON CONNECTING IT SAYS USB DEVICE NOT FOUND.

See this support document for instructions on how to deal with a disabled device or forgetting your passcode. iOS: Forgot passcode or device disabled

Photosmart 7515 connect via USB but not wireless, Device not found on Network

Purchased a 7515 all-in-one, was able to setup wirelessly to MacPro but has lost ability to connect wirelessly. This happened with OS X Lion and nor MountainLion. Have a TimeMachine Airport. Printer connects to network but during setup from MacPro, repeatedly get "Device Not Found on Network" after stepping through wireless installation setup screens. I have reset router, printer, firmware updates, software updates.... at wits end. I have followed the instructions on the below resource page link with no luck. Use WPA-PSK encryption (Automatic AES or TKIP) on network and diagnostics on printer pass.
Please help anyone!
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02946597&tmp_task=solveCategory&cc=us&dlc=en&la...

It sounds like the Macs and the printer just aren't communicating.
If you press the network icon on the printer, does it indicate it is connected to the network?
I recommend two additional steps that are not listed in the linked document. The printing system of the Mac may need to be reset as it will clear any software that could be interfering (such as corrupted installations).
Follow the steps as outlined for 10.7 or 10.8 in this document from HP.
The next step is to install the driver package from Apple. This can be found here.
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

HT201210 Iphone 4 problem....downloaded ios7 and its froze on "pic of connection with arrow up then i tunes, then i tunes icon" i go to restore and it says "device not found" although it is connected...

iphone 4 - yesterday it popped up to update to IOS7.... now it is froze on the screen as a picture (one end of connection with arrow up to itunes written out to itunes icon"..... ive tried restoring and it says "the iphone "iphone" could not be restored. Device not found".... although i do have it connected to my puter and have itunes activated.
i wished some one have warned me about this mess...
Judy

iOS: Unable to update or restore

HP Device Not Found Error when trying to print or scan wireless- HP Officejet Pro L7590

Have had HP Officejet Pro L7590 All-In-One Printer for years. Always worked fine and I had no issues printing via wireless connection. Several months ago.. Possibly after a Windows 8 update. From Windows 8 to Windows 8.1 I have not been able to use the printers wireless feature. When I try to print or scan it shows the printer as offline. Also get an error message that tells me "HP Imaging device is not found". I can still print when connected to USB. Cannot scan or use features of the HP software suite. I have tried several times to correct. Reloading the software and drivers several times, but no success. I just tried again and was able to print the test page wireless, so got all excited and thought I fixed it. Then tried to print something and got the same error message I have seen in the past. I have talked to certain supports saying that it may be a firewall setting within Windows. Any other suggestions? Thanks

Hi @rfjones002,
Welcome to the HP Support Forums! I see you are not able to print or scan wirelessly to your HP Officejet L7590 and your computer running the Windows 8.1 Operating system. You get a 'Printer offline' or 'HP Imaging device not found' errors.
I would like you to start with the steps listed below:
Hold down the Windows Logo key () on the keyboard and the 'R' to open the run box, type %temp%
Delete all files and folders from the temp folder. Choose skip if any pop ups appear saying any of the files could not be deleted
Uninstall the software again - Uninstall the Printer Software Instructions
When the uninstall has completed restart the computer
Follow these steps to reset the registry settings and options for Windows Installer.
Hold down the Windows Logo key on the keyboard and the 'R' to open the run box
In the Open box, type
msiexec /unregister
and then click OK.
Hold down the Windows Logo key on the keyboard and the 'R' to open the run box
In the Open box, type
msiexec /regserver
and then click OK
*Note: there is a space between the c and the /
If you have any difficulty with this step, please use this link to perform it another way. Restarting Windows Installer
Run Disk cleanup from Accessories\ System Tool < How to Delete files using Disk Cleanup
Download and install the latest version of Adobe flash player http://www.adobe.com/support/flashplayerflashplayer/downloads.html
Perform a clean boot > How to perform a clean boot in Windows
Download the following SP40669 File Download - if this does not download and or install please proceed to the next step.
Turn off the Real-Time Scanning and Firewalls; The image below is a McAfee example, if you have a different antivirus program and need help disabling Real-Time Scanning and Firewalls let me know.
- Image source
Now you can go ahead and download and install the software here >
HP Officejet Pro Full Feature Software and Driver
If you are unable to print a test page, please run the HP Print and Scan Doctor- It was designed by HP to provide users with the troubleshooting and problem solving features needed to resolve many common problems experienced with HP print and scan products connected to Windows-based computers.
Please let me know if this was successful! I will watch for your reply.
Thank you,
HevnLgh
I work on behalf of HP
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

Boot Device Not Found Please Intall an Operating system on your hard disk. Hard Disk - (3F0)

Hello,
I tried to re-install de OS from windows 7 to windows 8.1 and when the bios update driever was installed and the laptop was restaring it appeared the folowing window and message:
Boot Device Not Found Please Intall an Operating system on your hard disk. Hard Disk - (3F0)
After that i tried a lot of different ways to get to boot device select ...but i couldn't do anything. I removed the HDD and i put it back, i've tried with holding in the same time windows +B and pressing the power button in the same time for 1..2 seconds and then i've waited for at least 1 minute..and it didn't appeared anything on the screen. I've done the hard drive check and it passed. The weirdest thing is that when i want to select a boot device to re-install again the OS, i can't see any boot device to select. I need to mention that i've formatted the HDD in another computer. I dont care about the informations from the HDD beacause i saved all the informations on another device storage.
Please help me repair this problem!!! thanks a lot!
Have a nice evening.!!!

Whenever you get a message stating that the boot device not found it could be because of bad sectors on the Hard Drive. Its not necessary that the Hard Drive Test should fail to determine if the Hard Drive if its faulty or not. Sometimes even if the Hard Drive Test passes the Hard Drive will still not work because of the bad sectors in it.
Best way to find out if its the Hard Drive you can try the Hard Deive on a different Notebook which would help you determine if it's faulty or not.
Could be due to Application or driver conflicts, virus issues, file corruptions due to incompatible applications, improper shutdowns, update failures due to conflicts, sudden power surges, if notebook is dropped etc..
HP will provide a replacement Hard Disk Drive if the Notebook warranty is Active, If not you need buy a SATA Hard Disk Drive from a retail shop nearby
Please make sure you are getting at least equal capacity as the original one in order to use Recovery Disks. If you need you can buy a larger, but not smaller capacity Hard Disk Drive. For example if you have a 500GB Hard Disk Drive you can upgrade it to 750GB Hard Disk Drive but not 320GB Hard Disk Drive
Please try the below shown troubleshooting steps once:
Step 01. Remove the battery and unplug the AC/Power Adapter
Step 02. Press and hold the Power button for more than 30 Seconds
Step 03. Plug in the AC/Power Adapter (leave the Battery out for now)
Step 04. Press the Power button and check if the Unit works normal
If the above mentioned steps does not help, then you can try reseating the Hard Drive on your Notebook
If the issue persists again please Contact HP if your HP Notebook is under warranty, HP would replace the Hard Disk Drive and provide you a Recovery media to restore factory operating system after replacement (if you've not yet created Recovery Discs/USB Media)
Note: Back up all the personal data to an external drive if it's possible. Otherwise you could connect the failed HDD via SATA to USB adapter with another PC or same PC after replacement of HDD & re-installation of OS and try copying /recovering the files.
Please click on the link In order to Identify, Prevent, Diagnose & Recover from Drive Failures on HP Notebook Hard Drives & Solid State Drives :
http://h10032.www1.hp.com/ctg/Manual/c02876562.pdf
Please check your notebook warranty to verify the status and order a new Hard Disk Drive
Hope this helps, for any further queries reply to the post and feel free to join us again
**Click the KUDOS star on left to say Thanks**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.
Thank You,
K N R K
Although I am an HP employee, I am speaking for myself and not for HP

Boot Device Not Found, Please install an operating system on your hard disk, Hard Disk (3FO)

Hey
i am having this Error Message "Boot Device Not Found, Please install an operating system on your hard disk, Hard Disk (3FO)", While UEFI mode is enabled from bois but in Raid menu Both my hard Drives 1TB and SSD are Showing and I run the F2 System Diagnostics Test and it became as passed. In UEFI mode its not even showing my USB when i attach it for Window install But when i enabled the Leglacy mode it detteced my USB and also let me install my Windows and every thing seems to work fine. Updated the bios still Error is there.
Error Message only shows up when I disable the Leglacy mode.
So where is the Problem ? hard drive seems fine because these are working on Leglacy mode enabled.
Laptop Model : HP Envy Dv6-7211tx
Hard Drive : 1Tb and 32GB SSD

Hi Saifullay, sorry to hear that you are having issue with your Envy Dv6-7211tx. I have done some research and I have found a document that will assist you with this issues. Please click the link that I have provided to get to the document. http://h10010.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&dlc=en&docname=c01443463
If this does not resolve the issue, please feel free to write back . I would like to also apologize for the delay and the inconvenience that you have had to deal with.
Thank you.
Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
W a t e r b o y 71
I work on behalf of HP

T410 broadband device not found

Hello
I am trying to get the built in broadband device work (of course i have purcached the device and installed the hardware aswell as all the required softwares and driver which means the qualcomm gobi 2000 usb composite device 9205 driver and all the thinkvantage sofwares: access connection, active protection system, keyboard customizer utility, mobile broadband connect)
What i'm experiencing is that in the wireless connection status window / mobile broadband tab , under the connection status i see that it has recognised the t-mobile network i should be able to connect to. It says that i have a working connection for minutes with a good quality signal, but when i actually try to connect through the acces connections i get the error message of "connection failed" and i have the two options: "help me fix this" and "close" after i chose the help it goes to the diagnostic tools where the connection status is "not connected" cause "service provider not found" ...then i go to the "sign-up and support" button which leads me to the mobile broadband connect window where i get the following error "no wireless mobile broadband device found" and at the background it also says mobile broadband device not found.
I have tried to reinstall all the drivers and softwares replacing them with the latest ones which didn't have any effect on my problem.
Also i have checked the BIOS settings or my computers wireless settings in-case something is wrong, but everything was set as it should.
At last i have updated the BIOS to the latest one found on your site ( which is 1.32 2010/09/17) but still no change, and i am absolutely sure that the hardware device is installed correctly onto the laptops board.
I'm attaching a capture of the sreen which contains most of the details you need to know, in case i have missed something please let me know.
http://noob.hu/2010/11/15/Capture.JPG
Thank you in advance.
Best regards.
Gergő Csorba
B.Braun Medical Ltd.
Moderator edit: Converted pic >50k to link per the Community Rules. Removed Gergő's mobile number so that he doesn't get an unwanted fan club texting and calling.

Here's the Link for the 2539-AJ6, it does indicate that you have Bluetooth. Dowload and install the latest drivers.
http://support.lenovo.com/en_US/downloads/default.page?

HP 3050A : Device Not Found on Network

Hi,
Laptop Model: MacBook Air
Operation System: OSx Lion 10.7.3
Printer Model: HP 3050A
Router Model: Linksys WAG160N
WiFi Security Protocol: WPA
TCP/IP IPv4 Protocol: DHCP
Firewall Software: None
I have manage to connect the printer to my WiFi network as the blue indicator is ON and got an IP 192.168.1.104 with Excellent signal strength on the printer. But when follow the HP Setup Assistant I unpluged the USB then I got stuck with the following error message:
Device Not Found on Network
The wireless network settings were successfully downloaded to your device. However, your Mac was unable to locate the device on the network.
Please make sure that:
• Your Mac is connected to a wired or wireless network that has access to your device.
• Your device is connected to the wireless network "speedy".
Click "Retry" to attempt to connect again using the current settings. Click "Go Back" to enter different settings.
I also tried to ping the printer IP but no success
Aliss-MacBook-Air:~ ali$ ping 192.168.1.104
PING 192.168.1.104 (192.168.1.104): 56 data bytes
Request timeout for icmp_seq 0
Request timeout for icmp_seq 1
Request timeout for icmp_seq 2
Request timeout for icmp_seq 3
ping: sendto: No route to host
I am able to print using USB without any problem, but the WiFi never success! Please help!
Regards

Hello,
Thanks for the post. With this one, we may a couple of issues. I've included a link below with some excellent information regarding network connectivity. I might suggest that we start there and try to determine if it's the printer, the MAC or the network. Good Luck!
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02731071&tmp_task=solveCategory&cc=us&dlc=en&la...
I worked for HP but my posts and replies are my own....Thank you!
*Say thanks by clicking the *Kudos!* which is on the left*
*Make it easier for other people to find solutions, by marking my answer with (Accept as Solution) if it solves your issue.*

I'm receiving error Boot Device Not Found and Hard disk not exist when I boot up my laptop

I'm receicing the error Boot Device Not Found when i power on my HP G60-235DX laptop. After following HP's recommended troubleshooting steps, I receive error Hard disk not exist. Hmmmm....that's a little concerning. My guess is I need a new hard drive? I have the 17 recovery disks I made when I setup this laptop, however I'm not sure if they will resolve this issue. Any suggestions?

One of 3 things has happened, listed from most likely to least likely
1. Hard drive has died, replace it with one of the same size or larger, then use the HP recovery discs to re-install windows.
2, The motherboard has serious problems. (Replace the notebook)
3. The hard drive cable that connects it to the motherboard has somehow failed, not very likely. (replace the cable)
Replace the hard drive with a new one and use your recovery discs to get Windows back on it.
Here is your service manual, will show you how to replace the hard drive
http://h10032.www1.hp.com/ctg/Manual/c02985882.pdf
Recovery Instructions for Vista
Recovery Instructions for Windows 7

Presario CQ61 - Boot Device not found, Hard dis not exist

Hi i bought my presario CQ61-405AX 2nd hand roughly a year ago and it was almost new, my laptop was running fine, and then it froze, and so i had to turn it off, after i waited 30min for it to unfreeze, it now, when i boot it up, appears with a black screen, with the error
"Boot Device Not Found
Pleae install a operating system on your hard disk
F2 system diagnostiscs"
I went onto hp support and followed the prompts until it did a hard disk test and the error, "Hard Disk Not Exist" appeared
I have no idea how to fix it, i am running Windows 7 home premium, and i fear i may have to buy another hard drive
Thank's in advance
This question was solved.
View Solution.

Hi,
The most likely explanation is that your Hard Drive has failed and will need to be replaced, however as a further test, try the following.
1. Create a bootable Ubuntu CD - a guide on creating an Ubuntu CD and the download can be found Here.
2. When created, follow the guide on the link below to Try Ubuntu.
http://www.ubuntu.com/download/help/try-ubuntu-before-you-install
The 'Try Ubuntu' option runs the OS from the CD without the need to install on your HDD. If this runs Ok ( it will be slow running from a CD ), this would tend to confirm that the problem is with the HDD.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

Boot device not found. "Hard disk not exist". windows not booting

Product: HP G72-110SA
OS: Win7
two days ago, I was installing updates on my computer and when it was about to restart, it froze. After waiting for 10 minutes, I had to turn it off by pressing the off button. From then on, the computer turns on but shows a message "Boot device not found".
I have tried all the BIOS tests that I could find on the net for the hard disk, eg: http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01443465&tmp_task=solveCategory&cc=uk&dlc=en&la...
This gives me a "Hard disk not exist" error. I tried resetting the BIOS, that didn't work. I tried taking out and putting back in the battery, the memory and the hard disk. Still no luck.
I then booted ubuntu from cd on the computer. It works just fine, including the internet etc EXCEPT the HDD is still not detected.
I had some pretty important stuff and no back up, so would appreciate if someone can help me get back the data. If not, even if I know its just a HDD failure and not a motherboard/BIOS problem, it will be a relief as its probably fixable.
Thanks

Hi there ,
Thank you for visiting the HP Support Forums and Welcome! This is a great site to get answers and ask questions. I would be happy to assist you. As there are many models of HP Notebooks, I would need the model number. (How Do I Find My Model Number or Product Number?) When I went to www.hp.com/go/techcenter/startup, it gave me documentation and troubleshooting steps to follow. One of the documents it provided is called Hard Disk Error Displays before the Computer Starts. NOTE: I recommend at this point you make an immediate backup of all important data and files. Here are instructions on how to Backing Up Your Files (Windows 8). Please follow the troubleshooting steps provided, re-post with the results of the troubleshooting in detail. Thank you.

USB-6009 device not found problem

Similar Messages

Maybe you are looking for