Using Cisco Shell

Hi all,
I have a question,
We are using shell scripts to configure items on the switch.
We are replacing the older "C3560" switches from our network. We a replacing them with the newer "C3650" series.
But we are unable to get the shell scripts working with the new switch.
the config command for the 3560 switch was "shell init file tftp://172.x.x.x/shell/interface"
The newer 3650 switch does accept the commando but the shell does not work. If been looking for some time now but no solution.
It is possible that the shell is not supported on the new C3650 series of switches. But I cannot find that in the documentation.
I hope someone can help me with this
C3560 is running 122-55.SE8.bin
C3650 is running 03.03.05SE
Thanks in advanced
Greetings
Palermo

check using this
router(config)#shell processing full
router(config)#shell init {filename:URL no-exec}

Similar Messages

How do you create an array without using a shell on the FP?

I want to be able to read the status of front panel controls (value, control box selection, etc.) and save it to a file, as a "configuration" file -- then be able to load it and have all the controls set to the same states as were saved in the file. I was thinking an array would be a way to do this, as I have done that in VB. (Saving it as a text file, then reading lines back into the array when the file is read and point the control(s) values/states to the corresponding array element.
So how do I create an array of X dimensions without using a shell on the front panel? Or can someone suggest a better way to accomplish what I am after? (Datalogging doesn't allow for saving the status by a filename, so I
do not want to go that route.)

Thanks so much m3nth! This definitely looks like what I was wanting... just not really knowing how to get there.
I'm not sure I follow all the icons. Is that an array (top left with 0 constant) in the top example? And if so, that gets back to part of my original question of how to create an array without using a shell on the FP. Do I follow your diagram correctly?
If I seem a tad green... well I am.
I hope you understand the LabVIEW environment and icons are still very new to me.
Also, I had a response from an NI app. engineer about this problem. He sent me a couple of VI's that he threw together approaching this by using Keys. (I still think you are pointing to the best solution.) I assume he wouldn't mind m
e posting his reply and the VI's for the sake of a good, thorough, Roundtable discussion. So here are his comments with VI's attached:
"I was implementing this exact functionality this morning for an application I'm working on. I only have five controls I want to save, but they are all of different data types. I simply wrote a key for each control, and read back that key on initialization. I simply passed in property node values to the save VI at the end, and passed the values out to property nodes at
the beginning. I've attached my initialize and save VI's for you to view. If you have so many controls that this would not be feasible, you may want to look into clustering the controls and saving the cluster as a datalog file.
Attachments:
Initialize_Settings.vi ‏55 KB
Save_Settings.vi ‏52 KB

How do I use Cisco Registered Email Service with 10.7?

I received a email via someone using Cisco Registered Email/Envelope Service. The authentication process required the latest version of JAVA for 10.7, which I downloaded and installed. When I try to logon, the screen hangs with the message "Loading Envelope Tools." If I press "open" again it states "Inactive tools." The alternate method is to open the mail via a secure Web site, which I can open, but I am unable to download attachments. To download attachments, I am directed to a page that begins with "x-msg:" and I get a message that says: "Safari can't open the address .. . because MAC OX doesn't recognize Internet Addresses starting with "x-msg:"

Thanks for the info Roger, this is indeed did work for me (at least the part about signing in on apple.com, haven't tried the rest). Since Apple does not allow for the merging of Apple IDs, my plan is to use the old me.com address (from the free trial) with iCloud but then forward all the messages from the old me.com to my current Apple ID. Problem is all my devices are already associated with iCloud. So... if I want to activate iCloud using the old me.com, how do I do it?
I have two ideas: 1) as you suggest, signing out and signing back in through the iCloud preference pane (either on Mac OS or iOS); but I'm worried this will have consequence - will I be able to sign back in to my main Apple ID account after doing this?
2) create a new user on my Mac and then sign in to iCloud with the old me.com address there, then delete the account.
Thanks for any help with this.

Add or delete the summary links web part's[deployed as a VS solution] link using power shell

hi,
i am having a visual studio custom solution having page layouts implemented. In that solution i am having 1 summary links web part and in that i have hard coded few links and this is deployed on ion dev and staging env.
Now, the issue is : yesterday, customer came to me and asking me to change the links from http://abc to
http://xyz/ in this summary links. can anyone pls throw some light,such that i can change this link using a power shell script. i know if i go the VS solution and change the link and redeploy [ update-spsolution
command] will work.
but if the links are changing regularly , chnaging the vs solution and redeploying is not a good practice.
if i elaborate li'l bit, i am adding the screen shot : i need to get the summary link column's value and need to update[ delete xisting one and add new ones ]
is there any way , i can change the links using power shell script?
i tried the belwo power shells cript to get the page in the page layouts :
$web = get-spweb
"http://siteurl"
$pubWeb = [Microsoft.SharePoint.Publishing.PublishingWeb]::GetPublishingWeb($web)
$pagesListName = $pubWeb.PagesListName
$defaultAspxFile = $pubWeb.GetPublishingPage("$pagesListName/mycustomhome.aspx")
$summaryLinkFieldValue = New-Object
Microsoft.SharePoint.Publishing.Fields.SummaryLinkFieldValue
// here am getting the NULL VALUE
can i get the summary links field correctly and delete / modify the same?
help is appreciated!
##$groupLink = New-Object
Microsoft.SharePoint.Publishing.SummaryLink("My group")
#$groupLink.IsGroupHeader = $true $summaryLinkFieldValue.SummaryLinks.Add($groupLink)

Hi Shabeaut,
Could you tell us why do you want to add a link web part to the master page for all pages?
I tested that Summary Links web part (and other types of web parts) added in the master page under Quick Launch couldn't be edited when I edit the pages inherited from v4.master page, it looks by design.
Have you tried using the Quick Launch to add the link instead if you want to show links in all pages.
Thanks
Daniel Yang
TechNet Community Support

Sharepoint 2010 question : Error while deploying wsp file in using managment shell (power script)

When I tried to deploy the wsp's using managment shell (power shell scripts) everything looks good.
When I go and take a look the "manage farm solutions" thru sharepoint central admin, I see the deployment failed in two servers.
Error is
Could not load file or assembly 'c:\windows\Temp\solution-cxxxxxxxxxxxxxx\xxx.xxx.dll" or one of its dependencies. Access is denied.
Can you please let me know what could be the reason.
Note : I have two app servers and two web servers setup. The deployment is sucessful in 2 apps servers . but 2 web servers are giving error.
Thanks
Pichaimani

Hi,
According to your post, my understanding is that you wanted to failed to deploy the wsp's using managment shell.
You need to make sure that the dll is registered in the GAC.
Go to %Windows%\assembly. If the dll isn't there , you need to install it to the GAC on the server. Simply drag it into that folder in Windows Explorer, and it should install itself.
Here is a similar thread for your reference:
http://stackoverflow.com/questions/1265505/sharepoint-could-not-load-file-or-assembly-the-system-cannot-find-the-file-sp
Best Regards,
Linda Li
Linda Li
TechNet Community Support

Error Logging into Cisco Agent Desktop whilst using Cisco IP Communicator

Hi there,
I am having an issue whilst using Cisco Agent Desktop Version 7.0. If I use a cisco IP Communicator ( softphone) i get following message, "Login failed due to a configuration error. Please ask you system administrator to associate your phone with the RM JTAPI Provider user ID according to the instructions in the admin guide".
If user logs in to a normal Cisco phone then logs into agent there are no problems.
Bit of a novice so your help would be appreciated.

Hi
In your AppAdmin pages on UCCX, in the Unified CM Configuration screen, there is an 'RM' user defined.
This will be a user in CCMAdmin 'Application Users', which has all your CCX phones associated to it. UCCX uses this to CTI control the handsets... you need to associate the CIPC phone to that user.
Regards
Aaron
Please rate helpful posts...

Sending email attachments using unix shell script

hi
I want to send report generated my spooled file as attachment using unix shell script.
Can somebody help me out ?
many thanks

thanks a tonn it worked.
but i have another issue is it possible to add names in CC also ?
Also here is my code which spools the output of SP to a txt file. the File name is generated dynamically.
as shown below:
I need to send this generated file as attachement.
how do I do this? Here the shell script
=========================================================
#!/bin/sh
ORA_USER=scott
ORA_PWD=tiger
#Get the input parameter
if [ ! "$1" ]; then
STR="NULL"
else
STR="'"$1"'"
fi
#echo "exec pkg1($STR);"
#Connecting to oracle
sqlplus -s <<EOF
$ORA_USER/$[email protected]
---sql plus enviornment settings
set linesize 160
set pagesize 60
set serveroutput on size 1000000 for wra
set feedback off
set termout off
column dcol new_value mydate noprint
select to_char(sysdate,'YYYYMMDDHH24MISS') dcol from dual;
spool &mydate.report.txt
exec pkg1($STR);
spool off
EOF
exit
=========================================================
the file name will take sysdate as name so that every time a new file will be generated.
this file I need to send as attachment.
null

Problem accessing company resources remotely using Cisco VPN Client

I connect to my company's network remotely using Cisco VPN client both from a PC (v 4.0.1) and from a MacBook Pro (v 4.9.00)(same configs), and use Remote Desktop to connect to my work computer, and now i'm able to use Citrix to run applications on the company server.
The problem occurs on the Mac when I'm connecting from a location that uses the same private domain IP as our company's private domain. Our company's private domain is 192.168.1.x, so when I'm using the Mac on a WiFi router that happens to be set to 192.168.1.1, the Mac can connect using VPN but the remote desktop cannot connect to my work computer. Presumably, the Mac doesn't "know" that I'm trying to go through the VPN for the connection and not connect to something locally.
This problem seems to be unique to the Mac. Every Windows machine with the same client installed has no problems no matter what WiFi I've tried. The Mac works fine on any WiFi that is not 192.168.1.x.
However, since 192.168.1.x is very common (hotels, airports, etc., its a major problem with the Mac.
Suggestions are greatly appreciated!
Also, now that we're moving to Citrix, our administrator has created a webpage on the intranet that we launch applications from, but the Mac cannot find that page when connected to VPN from 192.168.1.x. Same problem.
Thanks in advance.

Hi,
I presume you have split-tunneling activated.
1. Make sure the 192.168.1.x is on the protected networks and on the MacBook client, disable "Allow local LAN access"
2. Create a separate group for the Mac users and assgn them a different pool (192.168.100.x )and advertise it in your company to point to the VPN Concentrator.
3. Use the NAT feature on your VPN concentrator.
If this helped, please rate.
Regards,
Daniel

New-CMGlobalCondition unable to create New script Condition using Power Shell

I am using config Manger 2012 and trying to use power shell cmdlet to create a new Global Condition using PowerShell but its not working for me using this
Do not understand how to use that command any idea.
New-CMGlobalCondition -DataType Boolean -DeviceType Windows -FilePath file.ps1 -Name test -ScriptLanguage PowerShell
Error comes as
New-CMGlobalCondition : No object corresponds to the specified parameters.
At line:1 char:1
+ New-CMGlobalCondition -DataType Boolean -DeviceType Windows -FilePath file.ps1 - ...
+ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ CategoryInfo : ObjectNotFound: (Microsoft.Confi...onditionCommand:NewGlobalConditionCommand) [New-CMGlobalCondition], I
temNotFoundException
+ FullyQualifiedErrorId : ItemNotFound,Microsoft.ConfigurationManagement.Cmdlets.AppModel.Commands.NewGlobalConditionCommand

Hi,
What's your version of SCCM? I ran this command line on SCCM 2012 R2 CU2.
It seems SCCM 2012 R2 CU2 fixed New-CMGlobalCondition cmdlet issue.
"The New-CMGlobalCondition cmdlet incorrectly requires use of the
-WhereClause parameter."
Description of Windows PowerShell changes in Cumulative Update 2 for System Center 2012 R2 Configuration Manager
Best Regards,
Joyce

Want to playback archived webcast recorded using Cisco webex recording. Downloaded Cisco webex meeting software from apple download page but still cannot play recording

Want to playback archived webcast recorded using Cisco webex recording. Downloaded Cisco webex meeting software from apple download page but still cannot play recording

You will probably find better support about the features of the Webex app on their support page here: http://www.webex.com/products/web-conferencing/mobile-iphone-ipad-faq.html
Doesn;t look like it's listed as a feature of the iPad app.

Create & Start UPS Service Using Power-Shell in SharePoint 2013

I want to know that is there a way to create a User Profile Synchronization Service using Power-Shell in a SharePoint 2013 Enterprise site? If so then how am I supposed to do that and start the User Profile Synchronization Service using the Power-Shell.
I'm seeking this help because the UPS service is stuck in Starting and both FIM Services are also not started but they are in Automatic start mode.
Could someone try to solve this matter.
Thanks,
regards,
Chiranthaka

start it from powershell will not help you resolve the issue.
Try below articles:
http://myspexp.com/2011/04/28/user-profile-synchronization-servicehangs-on-starting-i-fixed-it/
troubleshoot this issue:http://www.harbar.net/articles/sp2010ups2.aspx
http://www.sharepointdiary.com/2012/09/user-profile-synchronization-service-stuck-at-starting.html#ixzz2aXArH7zX

Using Power shell script how to hidden SharePoint existing features.

Hi Firends,
Using Power shell script how to hidden SharePoint existing features.
Please help me.
Thanks,
Tiru
Tiru

The Hidden property is set within the solution, so you would need access to the source code in order to set it.
Trevor Seward
Follow or contact me at...
&nbsp&nbsp
This post is my own opinion and does not necessarily reflect the opinion or view of Microsoft, its employees, or other MVPs.

Deploy wsp through Power Shell- start stop SP admin service and run execadmsvcjobs command using power shell

Hi,
Can anyone pls point me any link/ src code for deplyoing wsp using power shell. I know I can deploy it through Add-spsolution and install-spsolution, the issue is that, it will give "status - stuck in deploying scheduled..."
and i need to restart the sharepoint services - services.msc --> SP administration and timer services - and then i need to run the exceadmsvcjobs command to deploy / update the wsp successfully in solution store.
i mean, whats the power shell equivalent of these tasks. or anyone has already scripted these.
if i elaborate little bit, would like to know how to automatically Retract, Remove, Add and Deploy SharePoint 2010 WSP Solution Files with PowerShell

ok, i have found the same :
here its : hope this will help someone.
function wait4timer($solutionName)
$solutionName ="TestingWSP.wsp"
$solution = Get-SPSolution | where-object {$_.Name -eq $solutionName}
if ($solution -ne $null)
Write-Host "Waiting to finish soultion timer job" -ForegroundColor Green
while ($solution.JobExists -eq $true )
Write-Host "Please wait...Either a Retraction/Deployment is happening" -ForegroundColor DarkYellow
sleep 5
Write-Host "Finished the solution timer job" -ForegroundColor Green
try
# Get the WebApplicationURL
$MyWebApplicationUrl = "http://srvr:21778/";
# Get the Solution Name
$MywspName = "TestingWSP.wsp"
# Get the Path of the Solution
$MywspFullPath = "D:\myWorkspace\TestingWSP.wsp"
# Try to get the Installed Solutions on the Farm.
$MyInstalledSolution = Get-SPSolution | Where-Object Name -eq $MywspName
# Verify whether the Solution is installed on the Target Web Application
if($MyInstalledSolution -ne $null)
if($MyInstalledSolution.DeployedWebApplications.Count -gt 0)
wait4timer($MywspName)
# Solution is installed in atleast one WebApplication. Hence, uninstall from all the web applications.
# We need to unInstall from all the WebApplicaiton. If not, it will throw error while Removing the solution
Uninstall-SPSolution $MywspName -AllWebApplications:$true -confirm:$false
# Wait till the Timer jobs to Complete
wait4timer($MywspName)
Write-Host "Remove the Solution from the Farm" -ForegroundColor Green
# Remove the Solution from the Farm
Remove-SPSolution $MywspName -Confirm:$false
sleep 5
else
wait4timer($MywspName)
# Solution not deployed on any of the Web Application. Go ahead and Remove the Solution from the Farm
Remove-SPSolution $MywspName -Confirm:$false
sleep 3
wait4timer($MywspName)
# Add Solution to the Farm
Add-SPSolution -LiteralPath "$MywspFullPath"
# Install Solution to the WebApplication
#Install-SPSolution -Identity <SolutionName> -WebApplication <URLName> [-GACDeployment] [-CASPolicies]
install-spsolution -Identity $MywspName -WebApplication $MyWebApplicationUrl -GACDeployment #-FullTrustBinDeployment:$true -GACDeployment:$false -Force:$true
# Let the Timer Jobs get finishes
wait4timer($MywspName)
Write-Host "Successfully Deployed to the WebApplication" -ForegroundColor Green
catch
Write-Host "Exception Occuerd on DeployWSP : " $Error[0].Exception.Message -ForegroundColor Red
ref :
http://www.sharepointpals.com/post/How-to-Deploy-a-SharePoint-2013-Solution-(WSP)-in-the-Farm-using-PowerShell

How to Use the Shell

In another thread, the following was said:
So with your approach, you create the shell based on a Blank project, then after it has been created, you import.
Using the method being discussed allows you to omit creating the shell first. Instead, you import and create the shell at the same time.
Choosing one of the types such as Application Help or whatever just creates a project with certain things already in place and with topics that are partially fleshed out with information intended to help guide you along. Those are Project Templates. I created the one with the BigCo stuff in it years ago.
Cheers... Rick
That's groovy and all, but how can I use that to simplify my linked FM project? That is, the shell has content. When I link my FM content, it resides along with the unchanged shell content. How do I use this shell content with my imported content to make a better project more quickly?
Cheers,
Sean

So, when I link, RHStyleMapping.css does not pick up the FM styles I use and I don't get to set them up (such as setting my lists to Multilevel) en avance. And, I cannot make some basic changes, for example, such as excluding styles from the output.
[Edit] I can, as a separate step, manipulate Project Settings, but it seems you have to do this before the first time you generate, or you are sol. And, after I generate, only 4 of 40 FM styles are represented in RHStyleMapping.css and none are in default.css[/]
Not cool.

How to use "do shell script" when Terminal replies with a prompt?

Hey all,
I'm wondering how to properly use "do shell script" when Terminal replies with a question? In this example, I'm building a small tool in AppleScript that will auto-update the Android SDK via command line prompts. The problem is when I tell it to update all ("update sdk --no-ui"), I need to accept licence agreements before it continues, and the amount of licence agreements brought up is different every time.
So, basically, I'm wondering how to handle a case where "do shell script" encounters a case where Terminal would normally need a user's response to?
Thanks,
Behn

If it is variable number of prompts that is a problem. Look around hd and figure out how many prompts there will be. Ask around android forum for a bash solution. There are some test case apps that will let you put conditionals on output from running programs.
# traditional way. Pipe output to command.
do script "echo 'ok' | update sdk --no-u"
Here is the preferred way of getting administrator privileges.
It is easier to diagnose problems with debug information. I suggest adding log statements to your script to see what is going on. Here is an example.
    Author: rccharles
    For testing, run in the Script Editor.
      1) Click on the Event Log tab to see the output from the log statement
      2) Click on Run
    For running shell commands see:
    http://developer.apple.com/mac/library/technotes/tn2002/tn2065.html
on run
    -- Write a message into the event log.
    log " --- Starting on " & ((current date) as string) & " --- "
    -- debug lines
    set unixDesktopPath to POSIX path of "/System/Library/User Template/"
    log "unixDesktopPath = " & unixDesktopPath
    set quotedUnixDesktopPath to quoted form of unixDesktopPath
    log "quoted form is " & quotedUnixDesktopPath
    try
        set fromUnix to do shell script "sudo ls -l " & quotedUnixDesktopPath with administrator privileges
        display dialog "ls -l of " & quotedUnixDesktopPath & return & fromUnix
    on error errMsg
        log "ls -l error..." & errMsg
    end try
end run

Using Cisco Shell

Similar Messages

Maybe you are looking for