Using FMLE in windows server

Hi all,
I am now using FMLE to stream live video to FMS. However I only have 1 windows server running FMLE and 2 windows server running FMS. In order to stream 2 video sources, the server runs 2 FMLE and streams to both Primary and backup server.
But I have faced a problem after streaming for a few days, it shows: Incorrect sample given by the device. Stopping encoding session. Which stop streaming to the servers. I have checked that the server become extremely slow. So there are few questions I want to ask:
1. Is it better to run FMLE in a normal PC rather than using a server(Xeon(R) CPU E5-2440, 16GB ram)?
2. Will it lower the performance when running 2 FMLE to stream videos?
Could anyone please give me some advice.
Thank you.
William

That's exactly what I need - to use the hardware graphics renderer instead of the Microsoft Basic Render Driver as the default adapter in all Remote Desktop Services sessions, but this GPO doesn't work and you even said it's impossible due
to RemoteFX vGPU cannot be used with a Remote
Desktop Session Host (RDSH) or RemoteApp deployment.
Those two articles exclude each other:
this http://blogs.msdn.com/b/rds/archive/2014/06/06/understanding-and-evaluating-remotefx-vgpu-on-windows-server-2012-r2.aspx (RemoteFX
vGPU cannot be used with a Remote Desktop Session Host (RDSH) or RemoteApp deployment.)
and this Use the hardware
default graphics adapter for all Remote Desktop Services sessions

Similar Messages

Printing problem with Konica Minolta BizHub282 using RDP on Windows Server 2008 R2

Hello,
I have an office setup as follows: Local office IP adress scheme 192.168.201.x. There is a Konica Minolta BizHub 282 printer connected to the 192.168.201.x network as well as around 10 workstations running Windows 7. There are also about
10 additional teleworkers WHO DO NOT NEED print access to the Minolta 282. All of their data is on a cloud server. I have them setup to first connect to the cloud server using a RRAS PPTP VPN and then to start an RDP session to the separate
RDP server. The Konica Minolta works ??okay?? with the easy print services and until now, we have just dealt with the lack of features and the occasional print job that goes crazy and prints out 400 blank pages (btw, this is usually on Excel) or a job
that cuts off the margins even when you have it set to "fit to page" (this usually happens in Adobe.) When I originally set this up, I tried loading the native Konica drivers on the server, but there was no joy because I couldn't get it to
work using the native drivers. The problem at hand is a feature called "account track." This feature authenticates your print job by using an account code. If there is no code, the job just disappears. When I load the native
Konica driver, the ability to turn on this feature is greyed out (see below):
When I use easy print, the codes seem to go through, but as I mentioned earlier, sometimes the print job just goes insane. After researching this, it seems to me that there are two ways to overcome this if we can't turn off the account track feature:
1) Overcome the driver problem. I've tried both of their current drivers without success: VXL and Visual Postscript. When I login to RDP, the (redirected) Konica 282 printer is listed, but when I try to print, it fails due to the missing account track code.
I'm hoping that there is a registry hack to turn this feature on by default with the code or a driver version that works with RDP. They have a WHQL driver available, but it didn't work any better. Is there a way to report this issue to the WHQL labs? Maybe
I can light a fire under Konica's rear end and motivate them to fix the driver.
2) I saw one discussion where the guy installed the printer out in the clouds as a local printer. He seemed to have a site-to-site VPN, not a client-to-site VPN, so this worked. Is there a way to do something similar when the customer connects to the
VPN through standard "connect to workplace" setup? I tried pinging the Konica 282 from the server while logged into the VPN, but the printer could not be found.
3) I considered setting it up as a google cloud print prnter, but that would require everyone to setup a google account and add a layer of complexity.
Anyone else run into this and have a solution? If not, does anyone have any ideas on a solution or workaround?
Thanks,
Jeffery Smith

Hi Jeffery,
Thank you for your comment.
Yeah, you can use universal print driver by configuring Remote Desktop Easy print on RDS Server. Install the driver on RDS server. Now to configure Easy print you need to have minimum client RDP 6.1(But suggest you to install RDP 8.1), .Net Framework 3.5 or
above and RDSH role.
Also under GPO setting need to check below settings.
Do not allow client print redirection: Disable
Use Terminal Service Easy print printer driver first: Enable
Computer Configuration > Administrative templates > Windows Components > Remote Desktop Services > Remote Desktop Session Host > Printer redirection
For more information, you can refer below articles.
How to configure Microsoft RDS Universal Printing
http://www.virtualizationadmin.com/articles-tutorials/vdi-articles/microsoft-hyper-v/how-configure-microsoft-rds-universal-printing.html
Using Remote Desktop Easy Print in Windows 7 and Windows Server 2008 R2
http://blogs.msdn.com/b/rds/archive/2009/09/28/using-remote-desktop-easy-print-in-windows-7-and-windows-server-2008-r2.aspx?Redirected=true
Hope it helps!
Thanks.
Dharmesh Solanki

Can't install Adobe Reader using Firefox on Windows Server 2008 R2

I am hoping someone can kindly help me out here.
Using Firefox I went to http://get.adobe.com/reader/ and clicked the download button and received the Getplus add-on to Firefox.
When Firefox restarts the getplus window opens but sits there and does nothing with the window remaining blank for ever..
Each time I try it is the same
I am logged into Windows Server 2008 R2 as Administrator but it might be a permissions problem as this is a new install of 2008 and seems pretty locked down.
Thank you in advance

Are these signs of Adobe failing?
After subscribing to this forum, I received an email in German from Adobe......................
Vielen Dank für Ihren Beitritt im Adobe-Club. Als Mitglied können Sie eine Reihe exklusiver Vorteile, Ressourcen und Dienstleistungen in Anspruch nehmen.
Mitglieder können:
* unseren Newsletter Adobe Minute Mail (deutsch) abonnieren
* unseren Newsletter Adobe Edge (englisch) abonnieren
* Informationen zu ihren Käufen und Transaktionen im Adobe Store aufrufen
* ihr Adobe-Profil verwalten und aktualisieren
* in der Adobe Exchange Dateien hoch- und herunterladen
* Nachrichten in den Adobe-Foren veröffentlichen
Ihre Adobe-Club-ID lautet
Um Ihr Adobe-Profil und Ihre Voreinstellungen zu ändern oder um Adobe Edge zu abonnieren, loggen Sie sich einfach ein.
Whatever, Adobe

Specific layout using Work Groups (Windows Server 2012 R2)

I'm running Windows Server 2012 R2 in my company and we're interested in using the new Work Groups feature for a specific layout.
We currently have a shared folder with our personal work folders inside, to which only each respective user has access to. Then we have a public folder for all the people in the company to share files freely.
So what do we want? We want to have a local folder that synchs with our server folder and to which only each of us has access. We also want each of the work folders to be encrypted. What's my problem? I haven't understood too much about the new
feature yet. So far the feature is installed but it seems to me it can only be applied to one network folder (workgroup) entirely at a time. I want to sync each folder INSIDE the workgroup with the same number of local folder, and password-protect both.
How can this be done?

Hi,
Did you check this article?
Introducing Work Folders on Windows Server 2012 R2
http://blogs.technet.com/b/filecab/archive/2013/07/10/introducing-work-folders-on-windows-server-2012-r2.aspx
Regards.
Vivian Wang

Can Thunderbird and Lightning be installed and used as a Windows Server 8 r2 remote desktop application.

Can Thunderbird and Lightning be successfully installed as a remote desktop (terminal server) application on Windows Server 8 r2? In this scenario, users would access Thunderbird and Lightning via Windows (or Linux or Mac) remote desktop connection. Each user has there own home folder and profile on remote desktop server. I want to make sure that an individual user will be able to maintain individual email accounts, folders, settings, etc. as if Thunderbird and Lightning were installed on a stand alone PC. Any tips or things to watch out for in this scenario would be helpful.

There appears to be a problem with Firefox 20 with UNC paths when using roaming profiles on a server.
This is currently investigated and tracked via this bug report.
*[https://bugzilla.mozilla.org/show_bug.cgi?id=857672 bug 857672] - Address Bar not working
<i>(please do not comment in bug reports: [https://bugzilla.mozilla.org/page.cgi?id=etiquette.html])</i>

How to use itunes for windows server 2003

how to install itunes for windows server 2003

Purchased music from the iTUnes store is in a "AAC protected" format. It can only be used in iTUnes. Any music you buy online these days will have some protection on it where you can only use it in there program.
The way around this is to burn the purchased songs to a CD in iTUnes. Then goto edit>preferences>advanced tab>Import sub tab and set your import settings to something like MP3.
Now put the burned CD back in the PC and "Re"import it into iTunes so its imported in a MP3 format so you can use it in any program. Before importing it tho you need to manually add the name of the song, artist album ect ect

Using MPIO when Windows Server is your SAN

I have been studying and testing the Windows File Services and Storage options trying to understand how best to configure storage for my network. I am using iSCSI from File01 to connect to a virtual disk on Storage01.  I have read that
NIC Teaming is not recommended between a file server and the iSCSI. My primary objective is to increase throughput between Storage01 and File01. Since I do not have another switch to provide an additional layer of redundancy, I don't see much value
in the fault-tolerance scenario.
I have configured my network as seen in the image below. Each server (Storage01 and File01) has dual NICs attached to the storage VLAN on my switch with different IP addresses. The storage VLAN is not routed. All connections are 1Gig Ethernet.
My problem is that I cannot seem to get MPIO to recognize that there are two paths. Additionally, I cannot get Storage01 to allow me to define two separate iSCSI targets. I would like to define one target as T1-S1 and a second as T2-S2.
No matter what I try, I can only get one iSCSI target to be assigned to the VHD on Storage01. I believe this is good, as having an second iSCSI target pointing to the same VHD would probably lead to corruption.
So, I try to go to the iSCSI initiator side on File01. When I go to the Targets tab and add the Storage01 first IP, I can connect to the drive but I am unable to connect to the MPIO settings. Also, when I review the properties of the iSCSI disk
in Disk Management, I do not see the MPIO tab.
If MPIO does not work with this configuration, how can I get more than a single NIC worth of throughput for my iSCSI disk? I have tried NIC teaming and the throughput approachs speeds of a single connection--but nothing near what I would expect from
two bonded NICs.
Can I get some help understanding what I am missing or doing wrong?
Thanks!
Alex.

Hi Alex,
Thanks for contacting Microsoft. From your description, I learnt that the issue you are experiencing is that you failed to connect to the MPIO settings on Server File01. Please let me know if I misunderstand your purpose.
Firstly, I would like to explain that using Microsoft MultiPath IO (MPIO) to manage multiple paths to iSCSI storage. Microsoft does not support teaming on network adapters that are used to connect to iSCSI-based storage devices. This is because the teaming
software that is used in these types of configurations is not owned by Microsoft, and it is considered to be a non-Microsoft product. If you have an issue with network adapter teaming, contact your network adapter vendor for support. If you have contacted
Microsoft Support, and they determine that teaming is the source of your problem, you might be required to remove the teaming from the configuration and/or contact the provider of the teaming software.
The following best practices are recommended for networking when you use Microsoft iSCSI Initiator:
Use nonblocking switches, and set Configure Network Port Speed to a specific value rather than allowing speed negotiation.
Disable the unicast storm control. Most switches have unicast storm control disabled by default. If your switch has unicast storm control enabled, you should disable it on the ports that are connected to Microsoft iSCSI Initiator hosts and targets to avoid
packet loss.
Use MPIO to manage multiple network connections to the storage in Microsoft iSCSI Initiator. This provides additional redundancy and fault tolerance on Windows Server operating systems.
Note
Microsoft does not support the use of both MPIO and MCS connections to the same device. Use either MPIO or MCS to manage paths to storage and load balance policies.
Enable flow control on network switches and adapters. Flow control ensures that a receiver can pace the sender’s speed, and it is important in avoiding data loss.
Turn off the spanning tree algorithm for detecting loops. Loop detection introduces a delay in creating a port that can become usable for data transfer, and it can lead to application timeouts.
Segregate SAN and LAN traffic. SAN interfaces in Microsoft iSCSI Initiator should be separated from other corporate network traffic (LAN). Servers should use dedicated network adapters for SAN traffic. Deploying traffic for Microsoft iSCSI Initiator on
a separate network or networks helps minimize network congestion and latency. Additionally, traffic for Microsoft iSCSI Initiator is more secure when SAN and LAN traffic can be separated by using port-based virtual local area networks (VLANs) or physically
separate networks.
Configure additional paths for high availability. Use MPIO or multiple connections per session (MCS) with additional network adapters in the server. This creates additional connections to the storage array in Microsoft iSCSI Initiator through redundant
Ethernet switch fabrics.
Unbind File and Print Sharing from the Microsoft iSCSI Initiator network adapters that connect only to the Microsoft iSCSI Initiator SAN.
Use an Ethernet connection that is a gigabit or faster for high-speed access to storage. Congested or lower-speed networks can cause latency issues that disrupt access between Microsoft iSCSI Initiator and applications for devices that are connected through
Microsoft iSCSI Initiator. In many cases, a properly designed IP SAN can deliver better performance than internal hard disk drives. Microsoft iSCSI Initiator is suitable for WAN and lower-speed implementations, including replication where latency and bandwidth
are not a concern.
Use server-class network adapters. We recommend that you use network adapters that are designed for enterprise networking and storage applications.
Use CAT-6-rated cables for gigabit network infrastructures. For 10-gigabit implementations, CAT-6a or CAT-7 cable is usually required for use with distances over 55 meters.
Use Jumbo Frames if your network infrastructure supports them. Jumbo Frames can be used to allow more data to be transferred with each Ethernet transaction and reduce the number of frames. This larger frame size reduces the overhead on your servers and
iSCSI targets. For end-to-end support, each device in the network needs to support Jumbo Frames, including the network adapter and Ethernet switches.
In a server environment where uptime and redundancy are required, we recommend that you configure multiple network cards to allow redundancy in server environments. This section discusses network connections that typically have differing management requirements:
iSCSI network connection   The iSCSI data network is typically connected to a different network segment than the network that is used for client access. To provide redundancy for this connection, we recommend two or more ports
on two network adapters. These connections should be managed by MPIO to provide redundancy of the connections, and depending on the configuration, increased throughput.
Client access network   The client access network is a network port that uses a network segment that is dedicated for client access to the server. For example, clients use this network to connect to a file server, Exchange
Server, or SQL Server. For network adapter port redundancy, network adapter teaming can be employed to provide redundancy across two or more network ports, and in some configurations, increased throughput.
Management network   A management network is typically an isolated network segment that is used for server management. In some configurations, this can also be used for backup jobs to avoid impacting the data or client access
networks.
In addition to the three network types that are described in the previous paragraphs, in the case of a Windows Server Failover Cluster (WSFC) configuration, an additional network is needed for cluster heartbeat traffic. This network is dedicated for cluster
heartbeat traffic, and it is not used for any of the other types of traffic defined previously.
An example configuration is shown in the following table:
Server Configuration
Recommendation
Stand-alone server (non-clustered)
Six network ports across a minimum of two cards.
Configure two ports for client access (by using network teaming) and two ports for iSCSI connectivity to storage (by using MPIO for redundancy).
Configure one network interface for system management and one for system backups.
Windows Server Failover Cluster
Six network ports across a minimum of three network adapters.
Configure the same as above, plus add at least one port that is dedicated for cluster heartbeat traffic.
Where possible, network adapter ports should be connected to different network switches to allow for redundancy if there are issues with a network switch, as shown in the following figure:
Figure 3   Network switch redundancy
The previous figure depicts a network hardware configuration with a basic level of redundancy. In scenarios where greater levels of fault tolerance are required, additional connections can be configured, as shown in the following figure. The green and blue
lines represent additional levels of network fault tolerance.
Figure 4   Hardware configuration with additional connections
If anything is unclear, please feel free to let me know.
Best regards,
SOphia
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.

Got Display driver via Windows Update for Windows 8.1 and try to use it for Windows Server 2012 R2

Hi Everyone,
the following driver cab is from Windows Update:
https://onedrive.live.com/?cid=5be01620eea95d8c&id=5BE01620EEA95D8C!138&ithint=file,.cab&authkey=!APDi54-R1Ob5IWQ
It includes this display driver:
Intel(R) Q45/Q43 Express Chipset (Microsoft Corporation - WDDM 1.1)
My problem is: I can't install this driver on Windows Server 2012 R2.
I tried the following, nothing worked:
a) pnputil -i -a intel.cab
b) Extract cab, update the device's driver in device manager, select "search for driver software in this location"
c) copy the files in system32/, system32/drivers, syswow64/ from a Windows 8.1 system to a Windows Server 2012 R2 system
Isn't it true that any Windows 8.1 driver should also work for Windows Server 2012 R2 (same os version)?
Thanks for your replies.
PS: I first posted my question here:
http://answers.microsoft.com/en-us/windows/forum/windows8_1-hardware/got-display-driver-via-windows-update-for-windows/31c287c8-ef84-4c81-8530-8c51412376b7

Hi,
Additionally, did you check this article?
http://www.driveridentifier.com/scan/download.php?item_id=90475670&scanid=9B44546E3BB9410D877D9A90D1439AF8&hardware_id=PCI%5CVEN_8086%26DEV_2E12
Regards.
Vivian Wang

The most useful GPOs in Windows Server 2012R2

What are in your opinion the most useful GPOs in Server 2012 R2 that improving the work of the administrator and raising level of network security.
Cloud you share your opinion. please?
This topic first appeared in the Spiceworks Community

Good Morning All,I'm currently trying to run a script to convert all xls files to xlsxI am using a script written here:
https://gist.github.com/gabceb/954418The script as is:PowershellAdd-Type -AssemblyName Microsoft.Office.Interop.Excel$xlFixedFormat = [Microsoft.Office.Interop.Excel.XlFileFormat]::xlOpenXMLWorkbookwrite-host $xlFixedFormat$excel = New-Object -ComObject excel.application$excel.visible = $false$folderpath = "C:\temp\test\test_1"$filetype ="*xls"Get-ChildItem -Path $folderpath -Include $filetype -recurse | ForEach-Object `{ $path = ($_.fullname).substring(0, ($_.FullName).lastindexOf(".")) "Converting $path" $workbook = $excel.workbooks.open($_.fullname) $path += ".xlsx" $workbook.saveas($path, $xlFixedFormat) $workbook.close() ## Create old folder and move original files here $oldFolder = $path.substring(0, $path....

Unable to Deploy Software using GPO in Windows Server 2012

Dear Microsoft Team,
When I tried to deploy a software using GPO its giving an error -Add operation failed. Unable to extract deployment information from the package. Run validation on the package to ensure that the package is correct

Hi Subin,
I agree with Prabhu that the software package you deploy via group policy needs to in the format of .msi. The company or developer who produces the application provides the Windows Installer package .msi file and includes it with the application.
If a Windows Installer package does not come with an application, you might need to create a Windows Installer package by using a third-party tool.
Best regards,
Frank Shen

How to get Docupresentment IDS 2.5 installed using MSMQ on Windows Server 2012 working?

The test command threads.bat reqtype=sss display=yes is hanging. Verify that the Oracle Docupresentment Watchdog Server is running.

The threads.bat reqtype=sss display=yes command actually finished after several minutes with an error "fail to retrieve response message...". The problem was in the security setting of the input/output queues. Whoever executes the above command needs to have proper permission to the queues.

Snow leopard using documents from a windows server, I will have problems if I update to lion

Hi all,
I am working with my Macbook with Snow Leopard and I use files from windows server 2008 and also the accountance program reside on it, we always acceed by smb. I have not updated my Mac OX to Lion because I am frightened about lost my conection to this computers. Could I update or it is better to remain into Snow Leopard.
Thanks in advance

http://www.apple.com/pr/ may also have the answer when Apple is ready to reveal it.
Apple's "free" updates have typically been on http://www.apple.com/macosx/uptodate/
Consider first if you are ready for Lion by reading this tip. It is doubtful that not being ready for Lion will mean you'll be ready for Mountain Lion.

ASA and RADUIS on Windows server 2012

hi i have ASA5505 i want to get the Authentication from Raduis Server using NPS on windows Server 2012 i test the Raduis Server over "Kerio Control VMware Virtual Appliance" its work Perfect for testing my Setting on Raduis but with the ASA5505 i get this message "Error authentication rejected aaa failure"
Running Config
: Saved
ASA Version 9.1(3)
hostname NazcoFW
domain-name default.domain.invalid
enable password XgEKS9WizHnI9IUJ encrypted
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
passwd XgEKS9WizHnI9IUJ encrypted
names
interface Ethernet0/0
switchport access vlan 22
interface Ethernet0/1
interface Ethernet0/2
switchport access vlan 12
interface Ethernet0/3
interface Ethernet0/4
shutdown
interface Ethernet0/5
shutdown
interface Ethernet0/6
shutdown
interface Ethernet0/7
switchport access vlan 32
shutdown
interface Vlan1
nameif NAZCO
security-level 100
ddns update hostname OSI
dhcp client update dns server both
ip address 172.16.200.1 255.255.255.0
interface Vlan12
nameif outside4
security-level 0
ip address 172.16.4.254 255.255.255.0
interface Vlan22
nameif Outside20
security-level 0
ip address 172.16.20.254 255.255.255.0
boot system disk0:/asa913-k8.bin
ftp mode passive
dns domain-lookup NAZCO
dns server-group DefaultDNS
name-server 10.1.1.1
name-server 10.1.2.1
domain-name default.domain.invalid
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object network HP5220
host 10.10.10.105
object network ak20
host 10.10.10.110
object network hp5520
host 192.168.2.105
object network HP7000
host 192.168.2.106
object network HP5520
host 192.168.2.105
object network ak04
host 10.10.10.110
object network HP400
host 192.168.2.107
object network out04
range 192.168.2.200 192.168.2.220
object network AK04
host 10.10.10.110
object network oooo
subnet 10.10.10.0 255.255.255.0
object network 444
host 10.10.10.110
object network OSITOINT
subnet 10.10.10.0 255.255.255.0
object-group network OSItoOUT04
network-object object out04
access-list outside20_access_in extended permit icmp any4 any4
pager lines 24
logging enable
logging asdm-buffer-size 512
logging trap informational
logging asdm informational
logging host NAZCO 10.10.10.10 17/6161
logging debug-trace
logging permit-hostdown
mtu NAZCO 1500
mtu Outside20 1500
mtu outside4 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-721.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (NAZCO,outside4) source dynamic any interface dns
nat (NAZCO,Outside20) source dynamic any interface dns
route Outside20 0.0.0.0 0.0.0.0 172.16.20.1 1
route outside4 0.0.0.0 0.0.0.0 172.16.4.1 11
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa-server Keefa-Raduis protocol radius
aaa-server Keefa-Raduis (NAZCO) host 172.16.200.10
key *****
radius-common-pw *****
user-identity default-domain LOCAL
aaa authentication enable console LOCAL
aaa authentication http console LOCAL
aaa authentication serial console LOCAL
aaa authentication ssh console LOCAL
aaa authentication telnet console LOCAL
http server enable
http 0.0.0.0 0.0.0.0 NAZCO
snmp-server host NAZCO 10.10.10.196 community ***** version 2c
no snmp-server location
no snmp-server contact
snmp-server community *****
snmp-server enable traps snmp authentication linkup linkdown
snmp-server enable traps syslog
snmp-server enable traps ipsec start stop
snmp-server enable traps entity fru-insert
snmp-server enable traps remote-access session-threshold-exceeded
snmp-server enable traps connection-limit-reached
snmp-server enable traps cpu threshold rising
snmp-server enable traps ikev2 start stop
snmp-server enable traps nat packet-discard
crypto ipsec security-association pmtu-aging infinite
crypto ca trustpoint _SmartCallHome_ServerCA
crl configure
crypto ca trustpool policy
crypto ca certificate chain _SmartCallHome_ServerCA
certificate ca 6ecc7aa5a7032009b8cebcf4e952d491
308205ec 308204d4 a0030201 0202106e cc7aa5a7 032009b8 cebcf4e9 52d49130
0d06092a 864886f7 0d010105 05003081 ca310b30 09060355 04061302 55533117
30150603 55040a13 0e566572 69536967 6e2c2049 6e632e31 1f301d06 0355040b
13165665 72695369 676e2054 72757374 204e6574 776f726b 313a3038 06035504
0b133128 63292032 30303620 56657269 5369676e 2c20496e 632e202d 20466f72
20617574 686f7269 7a656420 75736520 6f6e6c79 31453043 06035504 03133c56
65726953 69676e20 436c6173 73203320 5075626c 69632050 72696d61 72792043
65727469 66696361 74696f6e 20417574 686f7269 7479202d 20473530 1e170d31
30303230 38303030 3030305a 170d3230 30323037 32333539 35395a30 81b5310b
30090603 55040613 02555331 17301506 0355040a 130e5665 72695369 676e2c20
496e632e 311f301d 06035504 0b131656 65726953 69676e20 54727573 74204e65
74776f72 6b313b30 39060355 040b1332 5465726d 73206f66 20757365 20617420
68747470 733a2f2f 7777772e 76657269 7369676e 2e636f6d 2f727061 20286329
3130312f 302d0603 55040313 26566572 69536967 6e20436c 61737320 33205365
63757265 20536572 76657220 4341202d 20473330 82012230 0d06092a 864886f7
0d010101 05000382 010f0030 82010a02 82010100 b187841f c20c45f5 bcab2597
a7ada23e 9cbaf6c1 39b88bca c2ac56c6 e5bb658e 444f4dce 6fed094a d4af4e10
9c688b2e 957b899b 13cae234 34c1f35b f3497b62 83488174 d188786c 0253f9bc
7f432657 5833833b 330a17b0 d04e9124 ad867d64 12dc744a 34a11d0a ea961d0b
15fca34b 3bce6388 d0f82d0c 948610ca b69a3dca eb379c00 48358629 5078e845
63cd1941 4ff595ec 7b98d4c4 71b350be 28b38fa0 b9539cf5 ca2c23a9 fd1406e8
18b49ae8 3c6e81fd e4cd3536 b351d369 ec12ba56 6e6f9b57 c58b14e7 0ec79ced
4a546ac9 4dc5bf11 b1ae1c67 81cb4455 33997f24 9b3f5345 7f861af3 3cfa6d7f
81f5b84a d3f58537 1cb5a6d0 09e4187b 384efa0f 02030100 01a38201 df308201
db303406 082b0601 05050701 01042830 26302406 082b0601 05050730 01861868
7474703a 2f2f6f63 73702e76 65726973 69676e2e 636f6d30 12060355 1d130101
ff040830 060101ff 02010030 70060355 1d200469 30673065 060b6086 480186f8
45010717 03305630 2806082b 06010505 07020116 1c687474 70733a2f 2f777777
2e766572 69736967 6e2e636f 6d2f6370 73302a06 082b0601 05050702 02301e1a
1c687474 70733a2f 2f777777 2e766572 69736967 6e2e636f 6d2f7270 61303406
03551d1f 042d302b 3029a027 a0258623 68747470 3a2f2f63 726c2e76 65726973
69676e2e 636f6d2f 70636133 2d67352e 63726c30 0e060355 1d0f0101 ff040403
02010630 6d06082b 06010505 07010c04 61305fa1 5da05b30 59305730 55160969
6d616765 2f676966 3021301f 30070605 2b0e0302 1a04148f e5d31a86 ac8d8e6b
c3cf806a d448182c 7b192e30 25162368 7474703a 2f2f6c6f 676f2e76 65726973
69676e2e 636f6d2f 76736c6f 676f2e67 69663028 0603551d 11042130 1fa41d30
1b311930 17060355 04031310 56657269 5369676e 4d504b49 2d322d36 301d0603
551d0e04 1604140d 445c1653 44c1827e 1d20ab25 f40163d8 be79a530 1f060355
1d230418 30168014 7fd365a7 c2ddecbb f03009f3 4339fa02 af333133 300d0609
2a864886 f70d0101 05050003 82010100 0c8324ef ddc30cd9 589cfe36 b6eb8a80
4bd1a3f7 9df3cc53 ef829ea3 a1e697c1 589d756c e01d1b4c fad1c12d 05c0ea6e
b2227055 d9203340 3307c265 83fa8f43 379bea0e 9a6c70ee f69c803b d937f47a
6decd018 7d494aca 99c71928 a2bed877 24f78526 866d8705 404167d1 273aeddc
481d22cd 0b0b8bbc f4b17bfd b499a8e9 762ae11a 2d876e74 d388dd1e 22c6df16
b62b8214 0a945cf2 50ecafce ff62370d ad65d306 4153ed02 14c8b558 28a1ace0
5becb37f 954afb03 c8ad26db e6667812 4ad99f42 fbe198e6 42839b8f 8f6724e8
6119b5dd cdb50b26 058ec36e c4c875b8 46cfe218 065ea9ae a8819a47 16de0c28
6c2527b9 deb78458 c61f381e a4c4cb66
quit
telnet timeout 5
ssh scopy enable
ssh 172.16.200.0 255.255.255.0 NAZCO
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
management-access NAZCO
dhcp-client update dns server both
dhcpd dns
dhcpd update dns both
dhcpd address 172.16.200.20-172.16.200.89 NAZCO
dhcpd dns 172.16.20.1 172.16.4.1 interface NAZCO
dhcpd lease 1048575 interface NAZCO
dhcpd update dns both interface NAZCO
dhcpd enable NAZCO
threat-detection basic-threat
threat-detection statistics
threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200
ssl encryption rc4-sha1 aes128-sha1 aes256-sha1 3des-sha1
username admin password bZmVDHuxUzzxS3yz encrypted privilege 15
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
inspect icmp error
class class-default
user-statistics accounting
service-policy global_policy global
prompt hostname context
service call-home
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
hpm topN enable
Cryptochecksum:357b7c6f861e8aa9bb3a3674a789b39b
: end
asdm image disk0:/asdm-721.bin
no asdm history enable

Hi
Looks like the AAA configuration is set for local
aaa authentication enable console LOCAL
aaa authentication http console LOCAL
aaa authentication serial console LOCAL
aaa authentication ssh console LOCAL
aaa authentication telnet console LOCAL
Change it to Radius
aaa-server Keefa-Raduis protocol radius
aaa-server Keefa-Raduis (NAZCO) host 172.16.200.10
key *****
radius-common-pw *****
for example :
aaa authentication telnet console Keefa-Raduis LOCAL
Now when you will do telnet to using Radius credentials, Its Should work, If radius goes down you can use LOCAL username and password as fallback method.
Cheers!
Minakshi(Do rate the helpful post)

Hyper link of public image(hyperlink or image) can not be saved on windows server 2012 and sharepoint 2010 problem

hyper link of public image(hyperlink or image) can not be saved on windows server 2012 and sharepoint 2010 problem, is this a bug?
thanks for any reply.
Rosone

It is not a bug, you might be using IE in Windows server 2012 and and browser might be restricting your site actions to respond properly.
Check this in a different browser or access site in a differ OS.
Adnan Amin MCT, SharePoint Architect | If you find this post useful kindly please mark it as an answer.

Windows Server 2008 SP2 X86 Product Key Issue

I am trying to create a VM using a Template, but facing an issue with respect to Product Key. The VHD I am using is of
Windows Server 2008 SP2 X86. If I do not provide Product Key in the Template/Guest OS Profile, the Virtual Machine creation fails even before starting. Seeing this behavior, I added a dummy key to the Guest OS Profile/Template which allowed
me to deploy the machine, but the VM gets stuck at Customization before failing. When I take the remote console of the VM, the Error I see at the Remote Console is:
Windows could not parse or process the unattend answer file for pass. The settings specified in the answer files cannot be applied. The error was detected while processing settings for component [microsoft-windows-shell-setup]"
So, I am confused now what to do.
Is dummy key supported?
Do I need to provide the actual key in the Template/Guest OS Profile?

You should be able to evaluate this software for 180 days.
Here are some info:
http://portal.sivarajan.com/2010/10/windows-2008-r2-evaluation-period-and.html
http://portal.sivarajan.com/2010/08/verify-and-extend-windows-2008.html
Santhosh Sivarajan | MCTS, MCSE (W2K3/W2K/NT4), MCSA (W2K3/W2K/MSG), CCNA, Network+ Houston, TX
Blogs - http://blogs.sivarajan.com/
Articles - http://www.sivarajan.com/publications.html
Twitter: @santhosh_sivara - http://twitter.com/santhosh_sivara
This posting is provided AS IS with no warranties, and confers no rights.

Using FMLE in windows server

Similar Messages

Maybe you are looking for