V5 in BPI Mode " Configuration data download to FPGA was not successful. DONE did not go high,"

Hello，everyone.
I am using virtex5 XC5VLX155 FPGA and trying to download mcs file to BPI flash and have failed.
The flash is JS28F512P30E. The iMpact version is 14.7.
FPGA's VCCINT is 1.0V, VCCAUX is 2.5V. VCCO is 3.3V.
M[2:0] is 010 in Master BPI. Ican program FPGA through JTAG. The FPGA_DONE pin 's LED can always flash.
The error is shown as below. the full IMPACT console log and the SCHEMATIC_ FLASH are in the attachment.
Using x16 mode ...
Setting Flash Control Pins ...
'1': Erasing device...
'1': Start address = 0x00000000, End address = 0x004E4AFF.
done.
'1': Erasure completed successfully.
Using x16 mode ...
Setting Flash Control Pins ...
INFO:iMPACT - Using Word Programming.
'1': Programming Flash.
done.
'1': Flash Programming completed successfully.
'1': Configuration data download to FPGA was not successful. DONE did not go high, please check your configuration setup and mode settings.
PROGRESS_END - End Operation.
Elapsed time = 692 sec.
Hope everyone give more advices. Thank you.

Thank you very much!
I can read ack the mcs file, but the file is much bigger than the original mcs file.
The flash datasheet is in the attachment.
I want to use the Master BPI mode. In BPI_UP, the address starts at 0 and increments by 1 until the DONE pin is
asserted. I do not know the difference between the BPI_UP and BPI_DOWN.
ps: The R61,R62 and R63 are not weld on the board. The ADV pin is tie to VSS .

Similar Messages

Virtex6:Configuration data download to FPGA was not successful. DONE did not go high, please check your configuration setup and mode settings

Hello，everyone.
I am using virtex6 FPGA and trying to download mcs file to PROM and have failed.
I download .bit file to FPGA and succeed.
When i try to download .mcs file to PROM XCF128X-FTG64C(BPI Flash) and choose Slave SelectMAP Mode
and the process is about 68% it fails.
The message below the IMapct is as belows:
done.
PROGRESS_END - End Operation.
Elapsed time =      0 sec.
// *** BATCH CMD : identifyMPM
// *** BATCH CMD : assignFile -p 1 -file "C:/Users/Administrator/Desktop/TEST/LED/led.bit"
'1': Loading file 'C:/Users/Administrator/Desktop/TEST/LED/led.bit' ...
done.
INFO:iMPACT:2257 - Startup Clock has been changed to 'JtagClk' in the bitstream stored in memory,
but the original bitstream file remains unchanged.
UserID read from the bitstream file = 0xFFFFFFFF.
INFO:iMPACT:501 - '1': Added Device xc6vlx240t successfully.
INFO:iMPACT - Current time: 2014/3/13 8:48:14
// *** BATCH CMD : Program -p 1
PROGRESS_START - Starting Operation.
Maximum TCK operating frequency for this device chain: 66000000.
Validating chain...
Boundary-scan chain validated successfully.
INFO:iMPACT - 1: Over-temperature condition detected! [ 230.52C > 120.00C]
1: Device Temperature: Current Reading: 230.52 C, Max. Reading: 230.52 C
1: VCCINT Supply: Current Reading:   2.997 V, Max. Reading:   2.997 V
1: VCCAUX Supply: Current Reading:   2.997 V, Max. Reading:   2.997 V
'1': Programming device...
Match_cycle = NoWait.
Match cycle: NoWait
LCK_cycle = NoWait.
LCK cycle: NoWait
done.
INFO:iMPACT:2219 - Status register values:
INFO:iMPACT - 0011 1111 0111 1110 0100 1011 1100 0000
INFO:iMPACT:579 - '1': Completed downloading bit file to device.
INFO:iMPACT:188 - '1': Programming completed successfully.
Match_cycle = NoWait.
Match cycle: NoWait
LCK_cycle = NoWait.
LCK cycle: NoWait
INFO:iMPACT - '1': Checking done pin....done.
'1': Programmed successfully.
PROGRESS_END - End Operation.
Elapsed time =     23 sec.
Selected part: XCF128X
// *** BATCH CMD : attachflash -position 1 -bpi "XCF128X"
// *** BATCH CMD : assignfiletoattachedflash -position 1 -file "C:/Users/Administrator/Desktop/TEST/LED/leda.mcs"
INFO:iMPACT - Current time: 2014/3/13 8:49:32
// *** BATCH CMD : Program -p 1 -dataWidth 16 -rs1 NONE -rs0 NONE -bpionly -e -v -loadfpga
PROGRESS_START - Starting Operation.
Maximum TCK operating frequency for this device chain: 66000000.
Validating chain...
Boundary-scan chain validated successfully.
INFO:iMPACT - 1: Over-temperature condition detected! [ 230.52C > 120.00C]
1: Device Temperature: Current Reading: 230.52 C, Max. Reading: 230.52 C
1: VCCINT Supply: Current Reading:   2.997 V, Max. Reading:   2.997 V
1: VCCAUX Supply: Current Reading:   2.997 V, Max. Reading:   2.997 V
'1': BPI access core not detected. BPI access core will be downloaded to the device to enable operations.
INFO:iMPACT - Downloading core file D:/Xilinx/14.3/ISE_DS/ISE/virtex6/data/xc6vlx240t_jbpi.cor.
'1': Downloading core...
Match_cycle = NoWait.
Match cycle: NoWait
LCK_cycle = NoWait.
LCK cycle: NoWait
done.
INFO:iMPACT:2219 - Status register values:
INFO:iMPACT - 0011 1111 0111 1110 0100 1011 1100 0000
INFO:iMPACT:2492 - '1': Completed downloading core to device.
Current cable speed is set to 6.000 Mhz.
Cable speed is default to 3Mhz or lower for BPI operations.
Current cable speed is set to 3.000 Mhz.
Setting Flash Control Pins ...
Setting Configuration Register ...
Populating BPI common flash interface ...
Common Flash Interface Information Query completed successfully.
INFO:iMPACT - Common Flash Interface Information from Device:
INFO:iMPACT - Verification string: 51 52 59
INFO:iMPACT - Manufacturer ID:        49
INFO:iMPACT - Vendor ID:             01
INFO:iMPACT - Device Code:           18
Setting Flash Control Pins ...
Using x16 mode ...
Setting Flash Control Pins ...
Setting Configuration Register ...
'1': Erasing device...
'1': Start address = 0x00000000, End address = 0x008CE03B.
done.
'1': Erasure completed successfully.
Setting Flash Control Pins ...
Using x16 mode ...
Setting Flash Control Pins ...
Setting Configuration Register ...
INFO:iMPACT - Using Word Programming.
'1': Programming Flash.
done.
Setting Flash Control Pins ...
'1': Flash Programming completed successfully.
Using x16 mode ...
Setting Flash Control Pins ...
Setting Configuration Register ...
'1': Reading device contents...
done.
'1': Verification completed.
Setting Flash Control Pins ...
Current cable speed is resumed to 6.000 Mhz.
'1': Configuration data download to FPGA was not successful. DONE did not go high, please check your configuration setup and mode settings.
`Elapsed time =    814 sec.
and i find many people have met the same thing. But they are spartan series FPGA and i try to low the Resistances of Mode pins,M0 M1 and M2, but the problem does not been solved.
I have read the status Registers and find there is an over-temperature state
and in Impact i could not readback the registers. It is strange.
I am anxious about this problem and have not solved it yet
What reasons may it be?
Hope for your answer, thank you

Hi~I want to know if you solve the configuration problem for virtex-6?
As I encounter the  same configuration problem, I want to consult  you with some question.
Can I have your email?
gszakacs wrote:
I have measured the VCCINT and find it is 1.0V, not 2.997V;
That is not at all surprising. I always assumed the problem is with reading the XADC (system monitor) block and not with the voltage or temperature.
my Reference board is ML605
That would have been nice to know at the beginning...
It seems that you have selected the correct mode, assuming your jumpers are set as required in the ML605 Hardware User's Guide. See table 1-27, table 1-33 and the note below it about switch S1.
I'm not that familiar with the details of this reference design, but it may be that the slave SelectMap circuitry requires a reset or power cycle to actually configure the FPGA. Have you tried power-cycling to see if the FPGA boots from the flash?
I'd also suggest that you select the V6 in the JTAG chain view, then go to the debug menu of Impact and select Read Device Status (this is from memory, but it's something like that). That will not only show the bits of the configuration status register, but also describe what each bit means. Among other things you can check the state of the FPGA's configuration logic and the Mode pins.

Configuration data download to FPGA was not successful.

I have designed a board with the Spartan 6 LX9 TQFP144 Package.
I am able to load a bitstream to the device with the digilent HS-2. However the fpga can not selfconfigure from
the attached SPI Flash.
Here is the console output from iMPACT:
GUI --- Auto connect to cable...
INFO:iMPACT - Digilent Plugin: Plugin Version: 2.4.4
INFO:iMPACT - Digilent Plugin: found 1 device(s).
INFO:iMPACT - Digilent Plugin: opening device: "JtagHs2", SN:210249983579
INFO:iMPACT - Digilent Plugin: User Name: JtagHs2
INFO:iMPACT - Digilent Plugin: Product Name: Digilent JTAG-HS2
INFO:iMPACT - Digilent Plugin: Serial Number: 210249983579
INFO:iMPACT - Digilent Plugin: Product ID: 30900152
INFO:iMPACT - Digilent Plugin: Firmware Version: 0109
INFO:iMPACT - Digilent Plugin: JTAG Port Number: 0
INFO:iMPACT - Digilent Plugin: JTAG Clock Frequency: 10000000 Hz
Attempting to identify devices in the boundary-scan chain configuration...
INFO:iMPACT - Current time: 27.07.2015 16:19:26
PROGRESS_START - Starting Operation.
Identifying chain contents...'0': : Manufacturer's ID = Xilinx xc6slx9, Version : 2
INFO:iMPACT:1777 -
Reading C:/Xilinx/ISE/14.7/ISE_DS/ISE/spartan6/data/xc6slx9.bsd...
INFO:iMPACT:501 - '1': Added Device xc6slx9 successfully.
done.
PROGRESS_END - End Operation.
Elapsed time = 0 sec.
Selected part: N25Q128
Unprotect sectors: FALSE
INFO:iMPACT - Current time: 27.07.2015 16:20:19
PROGRESS_START - Starting Operation.
Maximum TCK operating frequency for this device chain: 25000000.
Validating chain...
Boundary-scan chain validated successfully.
'1': SPI access core not detected. SPI access core will be downloaded to the device to enable operations.
INFO:iMPACT - Downloading core file C:/Xilinx/ISE/14.7/ISE_DS/ISE/spartan6/data/xc6slx9_spi.cor.
'1': Downloading core...
LCK_cycle = NoWait.
LCK cycle: NoWait
done.
'1': Reading status register contents...
INFO:iMPACT:2219 - Status register values:
INFO:iMPACT - 0011 1100 1110 1100
INFO:iMPACT:2492 - '1': Completed downloading core to device.
'1': IDCODE is '20ba18' (in hex).
'1': ID Check passed.
'1': IDCODE is '20ba18' (in hex).
'1': ID Check passed.
'1': Erasing Device.
'1': Using Sector Erase.
'1': Programming Flash.
'1': Reading device contents...
done.
'1': Verification completed.
'1':Programming in x4 mode.
'1': Configuration data download to FPGA was not successful. DONE did not go high, please check your configuration setup and mode settings.
INFO:iMPACT - '1': Flash was not programmed successfully.
PROGRESS_END - End Operation.
Elapsed time = 78 sec.
If i read that correctly Data was written to the Flash but the fpga was not able to configure from that data.
Done-pin is connected to 3.3V via a 470 Ohms Resisor.
The Flash is a N25Q128A13ESE40G, Datasheet here: http://www.farnell.com/datasheets/1674445.pdf
I can perform a readback, checksum and an erase.
If i do a read device status this is the console output:
INFO:iMPACT - Current time: 27.07.2015 16:36:27
Maximum TCK operating frequency for this device chain: 25000000.
Validating chain...
Boundary-scan chain validated successfully.
'1': IDCODE is '20ba18' (in hex).
'1': ID Check passed.
'1': IDCODE is '20ba18' (in hex).
'1': ID Check passed.
'1': IDCODE is '20ba18' (in hex).
'1': ID Check passed.
INFO:iMPACT - '1': Reloading FPGA configuration data stored in flash...
INFO:iMPACT:182 - done.
On the Flash side I have pulled s# and Hold up to 3.3V with 100k Resistors.
Can someone help me to find the problem?

So does the FPGA try to read the SPI flash when it boots ?
out with scope, probe the clock and the data , see if you can see it streamig out when you boot.
If so, then one other thing I see wrong a few times is data path of the SPI, single bit or 4 bits of data.
you have to make certain the bit file was created in the same width as the fgpa is expecting,
In ISE I think its in Impact where you make the SPI flash file and specify this .

I lost my iTunes library on my pc when the hard drive crashed. None of the data on the drive was recoverable and I did not have a backup. How can I get the music that resides on my ipod nano (4th generation back onto the new hard drive on my pc.

I lost my iTunes library on my pc when the hard drive crashed. None of the data on the drive was recoverable and I did not have a backup either locally or on the cloud. Much of the music is from old vinyl and podcasts which are no longer available.
How can I get the music that resides on my ipod nano (4th generation) back onto the new hard drive on my pc.
I have been reluctant to install iTunes on the new hard drive out of fear that I will lose all the contents on the ipod if I try to synch to the new hard drive.
Help!

No backup is a huge mistake.
You can redownload some itunes purchases in some countries:
Downloading past purchases from the App Store ... - Apple - Support

Can I recover data from a reformatted hard drive? I did not do a back up prior to talking to Apple Support and the guy having me delete the hard drive and start anew. My bad but is all lost??

Can I recover data from a reformatted hard drive? I did not complete a back up prior to talking to Apple Support and the guy having me delete the hard drive (10.5.8) and start anew (10.6.3). My bad but is all lost?? Years of very important information....

You will need to purchase reovery sofware such as such as FileSalvage
http://subrosasoft.com/software/filesalvage
You can download a demo copy that will tell you what it can recover
If you want to recover that you must pay for the software then
When you do the recovery, you will need another disk drive to receive the recovered files
Having install a new operating system on the disk after the retformat is going to gradually reduce the amount of data that this software will be able to recover for you
Allan

I bought a movie...verified my payment,but have nooo idea how to get the movie downloaded or where to even find it. did not purchase coud. that ought to be a free feature

I bought a movie...verified my payment,but have nooo idea how to get the movie downloaded or where to even find it. did not purchase coud. that ought to be a free feature

Go to Settings>General>Usage. How much space does it show you have?
If you connect your phone to your computer, what does iTunes say is on your phone? Do you see a large amount of "Other"? If so, you may have a corrupted database. You'll need to sync your phone then restore it as NEW (not from back up) then re-sync your data).

I plugged IPOD in to sync ( first time in over a year) it auto started with the "Do Not Disconnect", but did not sync. Now the IPOD is stuck in that mode, won't shut off, won't sync, won't work. is there a way to reboot it?

I plugged IPOD in to sync ( first time in over a year) it auto started with the "Do Not Disconnect", but did not sync. Now the IPOD is stuck in that mode, won't shut off, won't sync, won't work. is there a way to reboot it?

It has already been 6 days from your post, my apology for responding so late, but it is my habit to help only the leftovers, which the other contributors missed.
Toggle the hold switch make sure there is no red showing.
To reboot an iPod. (Or RESET in Apple iPod jargon)
Press Menu and Center button for about 10 secs till the Apple logo comes ON , this would not erase any data from your iPod.
I would advice you to leave the iPod charging for about 4 hours, if it has been discharged for 1 year or more, and also Apple recommends that you charge the iPod at least once a month, to prevent a discharged battery leakage, which may corrrode the circuitry in the iPod.
Hopefully you don't get the dreaded RED X on the iPod screen.
Good Luck!

I recently have ipad but before i sell it i made a back up of it and by an iphone when i put all the date on my iphone some files and software did not install is there anything i can do to recover the lost data? please help

i recently have ipad but before i sell it i made a back up of it and by an iphone when i put all the date on my iphone some files and software did not install is there anything i can do to recover the lost data? please help

I don't think you're on iOS 5, I think you're using iOS 6. That's the latest version.
Unless you've used iCloud to back up your documents, you won't be able to restore them. And for future reference, you don't have to uninstall Pages to update your iPad anymore. Sorry about this.

Can you please help to understand how the firefox decides on the Expires date for a cached javascript file ( my server did not set any Expire header, but firebox set it down).

# Question
Can you please help to understand how the firefox decides on the Expires date for a cached javascript file ( my server did not set any Expire header, but firebox set it down). I tried to understand but different javascript file gets different Expires date value when it is being cached. Please help me as I tried lot and could not get proper answer for this. Thanks in Advance.

Try posting at the Web Development / Standards Evangelism forum at MozillaZine. The helpers over there are more knowledgeable about web page development issues with Firefox. <br />
http://forums.mozillazine.org/viewforum.php?f=25 <br />
You'll need to register and login to be able to post in that forum.

How to verify my account it always says when i downloaded a free app it says i did not alreadyverify

ow to verify my account it always says when i downloaded a free app it says i did not alreadyverify

Did you successfully verify yur account as asked in the message? To verify:
How do I verify my Apple ID by email?
Simply follow the link in the verification email that says "Verify Now." Sign in with your current Apple ID and password, then click Verify Address. You can also verify by signing in at My Apple ID. You'll receive an email prompting you to verify.

I was downloading an album, but the last song did not make it? Store said it could not do it at this time.

I was downloading an album, but the last song did not make it? Store said it could not do it at this time. There is black disk before the song?

Hey Skip,
I would check your Purchased section in the iTunes Store to see if you can try to download it again:
Downloading past purchases from the iTunes Store, App Store, and iBooks Store
http://support.apple.com/kb/HT2519
Welcome to Apple Support Communities!
Have a great day,
Delgadoh

How do I stopi-Tunes from downloading songs on my device which I did not order and which I then have to delete?

How can I stop i-Tunes from downloading songs on my device which I did not order and which I then have to delete because I do not want it?

Does swiping/dragging across the tracks from right-to-left (or possibly left-to-right depending upon the iOS version) in the Downloads tab in the iTunes store app stop them downloading ?
If it's the U2 album Songs of Innocence then : http://itunes.com/soi-remove
If it's a different album/tracks and you didn't buy them, and nobody else has access to your account and/or devices and bought them, then contact iTunes Support : http://www.apple.com/support/itunes/contact/ - click on Contact iTunes Store Support on the right-hand side of the page

HT4623 I download the software update but the update did not installed

I download the software update but the update did not installed

Did you do this download on the phone, or in iTunes? If on the phone, after the download did you select install? Same with iTunes, did you select update and install or just download? What did it do? Is anything showing on your phone?

HT2311 After waiting 27 minutes while the new iTunes supposedly downloaded onto my computer, the Finder window did not appear, and the iTunes.mpkg icon didn't appear on my desktop (where downloads usually go). What do I do?

After waiting 27 minutes while the new iTunes supposedly downloaded onto my computer, the Finder window did not appear, and the iTunes.mpkg icon didn't appear on my desktop (where downloads usually go). I also looked for the new iTunes by clicking on my Hard Drive icon but didn't see it there either. I only see the icon for the old iTunes. What do I do?

The exclamation mark means that the app has lost the link to the actual file.
First step: try and make sure the iPhoto Library is working correctly:
Go to the App Store and check out the Purchases List. If iPhoto is there then it will be v9.6.1
If it is there, then drag your existing iPhoto app (not the library, just the app) to the trash
Install the App from the App Store.
Sometimes iPhoto is not visible on the Purchases List. it may be hidden. See this article for details on how to unhide it.
http://support.apple.com/kb/HT4928
One question often asked: Will I lose my Photos if I reinstall?
iPhoto the application and the iPhoto Library are two different parts of the iPhoto programme. So, reinstalling the app should not affect the Library. BUT you should always have a back up before doing this kind of work. Always.

Variant Configuration Data download from R/3 to CRM

Hello all
It may be a very dumb question, but I would certainly appreciate an answer.
We are currently using SAP R/3 4.6c and heavily use VC for configurable products and also for pricing.
Now we wish to explore the possibility of using SAP CRM 5.0 to enable our sales force to use CRM PCUI to create quotes for configurable materials.
My questions are as following:-
1. Is it possible to download all VC related data into CRM from R/3 including pricing? I understand that for different VC object, I will have to use different CRM objects but is it possible? If the data transfer is possible, is it typically done by a middleware resource?
2. I would also like to confirm that by creating a run time version and Kbase is pre requisite to enable the download to CRM.
If you could please point me to the appropriate help on this topic, I would really appreciate it.
Best regards
Jai

Hi Gun,
In your message, You stated
As recommended by SAP, if we have R/3 link into our CRM
the best scenario is to get VC product from R/3 into CRM.
Is there any documentation tjhat backs this up? could you give it to me
we have a situation in our company where we have been using a home grown product that not only lets you configure product bu it also takes the user through a selling experience for example it asks the user if he is interested in buying any accessories for the product and provides options through pop messages and the user can select. this way it takes leads the user through questionnaires that comes in pop ups to select a product
we have crm service and ecc implemented and now we need to implement this feature for the crm sales piece
the question is do we go for PME or variant config that is already set up in ECC ?
the link and middle ware set up between ECC and CRM is also available so we can bring the variant configuration from ECC into crm. but how about the questionnaires and the selling experience that is available through pop up questionnaires,
we can set up the selling experience via the Product modeler but as a company we need to make a decision whether we bring the varinat configuration from ecc and use the selling experience for the pop up questionnaires that leads customer
or should we just use sales packages that behaves similarly like varinat configuration and add enahcnements to create the pop- up questionaires
Could you direct /provide some guidance in this area?
Sara

V5 in BPI Mode " Configuration data download to FPGA was not successful. DONE did not go high,"

Similar Messages

Maybe you are looking for