VoIP (Internet Ready) phone connected to Airport Extreme?

I have Airport Extreme (7.6.4) and have it hard connected to a Comcast router. Router is in the basement across the house and the Airport Extreme is in the first floor office. I want to connect a VoIP phone directly to the Airport Extreme instead of running another line from the router directly to the phone. Can this be done? Is there any connectivity issues with a VoIP phone directly into the Airport Extreme? Any tips or suggestions for, or against, this?
Many thanks!

Yes. Disable that. Using that may make you feel good but the MAC addresses are easily discovered and cloned. Instead use WPA with a non-dictionary password.

Similar Messages

Internet connection via Airport Extreme/router thats not working, why?

I have been having problems with the internet connection via Airport Extreme which I find it a bit unusual and its still driving me nuts! This is what happened:
I have lost my internet connection last Sunday evening upon my return from a weekend away from home. The last time I have used the internet connection on my macbook was the previous Friday morning. Prior to the apparent disconnection on Sunday, I have always used my internet connection wirelessly through Airport Extreme (that is connected via ethernet cable to the NETGEAR DG834v2 ADSL modem which had worked beautifully until the problem arose on my return). This wireless internet connection allowed me to surf the internet anywhere in my home.
However, upon the successful re-connection to the internet via the modem router, I have discovered several new problems. I have tried to set up the internet connection wirelessly again but instead the following happened:
1. Router (Netgear) drops ADSL connection and cannot reconnect when connected to airport via Ethernet. (which is the case when using airport wireless).
2. Router connects to ADSL fine when computer is connected to it via Ethernet. (However, router disconnects when magsafe power adapter is taken out for some inexplicable reason!)
3. Router connects to ADSL fine when nothing is connected to the router (ie. No Ethernet connections)
4. Router connects to ADSL fine when connected to airport via Ethernet and computer is connected to airport via Ethernet.
So from the above, I cannot connect to the internet properly whether wirelessly or not so I suspect it could be faulty router or could it be airport extreme? I have asked my ISP for an explanation and all they have said is that it cannot be the mis-configuration but could be to do with the power adaptors or the way plugs are set up and suggested I take out all the power plugs (and power surge protector) out to switch everything off, the macbook, router, printer and airport extreme. However, when I have re-plugged them all back in, the problems I have described above still persists!
Would appreciate any help if anyone here recognises why this is the case and what seems to be the cause of this. If so, what should I do? Though I have written back to my ISP again yesterday for more help so im waiting to hear from them...
Thanks
u2dougal

I have been having problems with the internet connection via Airport Extreme which I find it a bit unusual and its still driving me nuts! This is what happened:
I have lost my internet connection last Sunday evening upon my return from a weekend away from home. The last time I have used the internet connection on my macbook was the previous Friday morning. Prior to the apparent disconnection on Sunday, I have always used my internet connection wirelessly through Airport Extreme (that is connected via ethernet cable to the NETGEAR DG834v2 ADSL modem which had worked beautifully until the problem arose on my return). This wireless internet connection allowed me to surf the internet anywhere in my home.
However, upon the successful re-connection to the internet via the modem router, I have discovered several new problems. I have tried to set up the internet connection wirelessly again but instead the following happened:
1. Router (Netgear) drops ADSL connection and cannot reconnect when connected to airport via Ethernet. (which is the case when using airport wireless).
2. Router connects to ADSL fine when computer is connected to it via Ethernet. (However, router disconnects when magsafe power adapter is taken out for some inexplicable reason!)
3. Router connects to ADSL fine when nothing is connected to the router (ie. No Ethernet connections)
4. Router connects to ADSL fine when connected to airport via Ethernet and computer is connected to airport via Ethernet.
So from the above, I cannot connect to the internet properly whether wirelessly or not so I suspect it could be faulty router or could it be airport extreme? I have asked my ISP for an explanation and all they have said is that it cannot be the mis-configuration but could be to do with the power adaptors or the way plugs are set up and suggested I take out all the power plugs (and power surge protector) out to switch everything off, the macbook, router, printer and airport extreme. However, when I have re-plugged them all back in, the problems I have described above still persists!
Would appreciate any help if anyone here recognises why this is the case and what seems to be the cause of this. If so, what should I do? Though I have written back to my ISP again yesterday for more help so im waiting to hear from them...
Thanks
u2dougal

Can't connect to internet via MacBook Pro to Airport Extreme

I can't connect to internet via MacBook Pro to Airport Extreme. I reset AE and modem (power down and back up again). Some computers on my home network will connect fine and others won't. The ones that won't don't populate the DNS server or the Search Domains. AE shows up on all the machines. I have one computer also connect to AE via ethernet and it has the same symptoms. Why do some Macs connect and others don't. Even when I get them to connect when I shutdown or put in sleep mode over night I lose the internet connection and have to start all over. Very frustrating.

Regrettably no replies. I have struggled with this for days with no success and I have given up on the Airport Extreme. I have found several other Forum posts with very similar problems and no one seems to have a solution to this. It seems other wireless routers work better than the Apple product. I was able to get my old Linksys wireless router reset and it is set up and working well. The Linksys router does populate the DNS servers and domains where as the AE does not. Apple engineers should look into this. If I am mistaken and there is a fix for this someone please let me know, otherwise my AE will probably appear on Ebay very soon.

I can connect to internet with my MBP through Airport Extreme, but my iOS devices can't. Please help.

I can connect to internet with my MBP through Airport Extreme, but my iOS devices can't. Please help.

GerleMan, Welcome to the discussion area!
There are two probably causes:
Your ISP is blocking the port used by Entourage to send mail and the ISP used by the other wireless networks is not.
OR
Your ISP doesn't like OS X's default MTU seting of 1500. If this were the case it should also affect any large file transfers you try to make from your Mac to the Internet.

Do I need to connect the AirPort Extreme with a ethnet cable

Do I need to connect the AirPort Extreme with a ethnet cable

Hi Tracy,
I have an airport express connected by ethernet cable to a Netgear modem which is connected to a phone socket. Those devices stay at one end of the house. I can use my MacBook Pro to connect to the internet (by Wi-Fi, no cables) anywhere else in the house. I hope this helps.
Ian.

How do I connect my Airport Extreme 802.11n to Epson 645 Printer?

I can't figure out how to connect my Airport Extreme 802.11n to my Epson 645 Printer. Can anyone help me? Thanks!

You may want to try reinstalling Mavericks. Airport Utility installed by Mavericks may no longer connect to your older AEBS (though I've not heard that.) Installing the Old AirPort Utility (Version 5.6) on Mountain Lion | frank.is.
Reinstall Lion, Mountain Lion, or Mavericks
     Boot to the Recovery HD: Restart the computer and after the chime press and hold down the
     COMMAND and R keys until the Utilities menu screen appears. Alternatively, restart the computer and
     after the chime press and hold down the OPTION key until the boot manager screen appears.
     Select the Recovery HD and click on the downward pointing arrow button.
     Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the Utilities menu.
     Repair the Hard Drive and Permissions as follows.
After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
     Reinstall Lion/Mountain Lion, Mavericks: Select ReinstallLion/Mountain Lion, Mavericks from
     the Utilities menu, and click on the Continue button.
     Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is
                three times faster than wireless.

How do I connect my airport extreme to windows 8.1

how do I connect my airport extreme to windows 8.1

Connect an Ethernet cable between the U-verse router's LAN port to the WAN (circle-of-dots) port on the AirPort Extreme Base Station (AEBS). Since you will have two routers in series, you will want to reconfigure the AEBS as a bridge. (ref: AirPort Utility > Select the AEBS > Manual Setup > Internet > Internet Connection tab > Connection Sharing = Off (Bridge Mode))

How do I connect my Airport Extreme to an AT

How do I connect my Airport Extreme to an AT&T U-verse Modem/Router?

Connect an Ethernet cable between the U-verse router's LAN port to the WAN (circle-of-dots) port on the AirPort Extreme Base Station (AEBS). Since you will have two routers in series, you will want to reconfigure the AEBS as a bridge. (ref: AirPort Utility > Select the AEBS > Manual Setup > Internet > Internet Connection tab > Connection Sharing = Off (Bridge Mode))

Cannot connect to internet with iMac connected to airport via Ethernet

Hi all,
Firstly please forgive if this problem has been posted before but unfortunately i haven't yet been able to find a solution to my problem.
I cannot seem to get my wireless network to work since updating my Airport to v5.7. I have reverted back to 5.6 but with no joy. OK, here's my setup - I have an iMac G5 1.8 which is connected to my airport via an ethernet cable (it is plugged into the correct port) and an iBook with an Airport card to connect wirelessly. The airprot is connected to my ADSL modem which is a D-Link 300T. When set up like this my iMac cannot connect to the internet even though my iBook can. When i take the4 iBook and Airport out of the equation my iMac connects fine to the internet via ethernet cable direct to my modem.
As i've said, as soon as i bring in the iBook and Airport the iMac cannot connect via airport extreme, even though the iBook can connect.
I have searched through the discussions looking for clues and answers. I have made sure that distrubute IP address is not checked and that internet sharing is off on my iMac but on on my iBook. I have tried all channels and all possible different settings on the airport admin utility but nothing works.
I hope i've given enough information to give a clear indication what is wrong, if not please ask and i will try my best to answer. Any help would be much appreciated so i can convince my girlfriend that buying my iBook was not "a waste of money!".
Many thanks in advance,
Carl.

Same questions as Paul.
Open up the Network System Pref on the iMac G5.
If you pick Show: "Network Status", what do you see ? Be precise.
If you change Show: to "Built-in Ethernet", what do you see on the TCP/IP, PPPoE and Ethernet tabs ? Again, be precise.
On the Network Status, you should see a green mark next to Built-In Ethernet, which should be at the top. It should also give you an IP address and tell you you are connected to the Internet. Well it would if it was working, so "say what you see".

Mouse quits w/printer connected to airport extreme

After 2+ yrs w/ no problems, now, mice will not move cursor when HP PSC2410 is connected to Airport Extreme, internet is OK. If I plug the printer directly into the mini, mice work fine. What the........!&%$

After 2+ yrs w/ no problems, now, mice will not move cursor when HP PSC2410 is connected to Airport Extreme, internet is OK. If I plug the printer directly into the mini, mice work fine. What the........!&%$

Devices not connecting through Airport extreme wired connection

Hi
I just got an Airport extreme to use as an extention of my existing network, and to plug some devices in so that they can connect to the internet for updates (Sony Blu-ray player, dish network receiver, slingbox)...
my wireless is from a linksys/cisco wireless router (4-port) wrt310n, that is connected to my cable modem. The airport is set and has the green light showing. The blu-ray player and dishnetwork receiver are plugged into two of the ports. The blu-ray player says it can't connect to the internet. The dish network receiver says it is connected, giving ip address/submask, etc.
If I take my macbook pro and turn off wireless and plug into the airport it will not connect to the internet.
What have I not done to allow wired connection to the airport extreme to connect to the net?
thanks
David

Thanks for the clarification of your setup.
Unfortunately, the bottom line here is that this is not going to work.
The ethernet ports on the Extreme will only be active if you configure the AirPort Extreme to "extend a wireless network". But, it can only "extend" a wireless network from another Apple router. It's not compatible for this purpose with your Cisco router or any other manufacturer's router.
If you are unable to connect the AirPort Extreme to your router using an ethernet cable, you might want to take a look at a pair of ethernet powerline adapters to accomplish the same task by using the wiring in your home to transmit the ethernet signal.
I should clarify that if you connect the Cisco and AirPort Extreme using ethernet, you would not use the "extend" setting on the AirPort Extreme. This is only used if the device is connecting to another Apple router.
Message was edited by: Bob Timmons

I changed my internet box and now my airport extreme light flashes amber what I need to do to get the green light back

I changed my internet box and now my airport extreme light is flashing amber but I have internet connection, how can I get the green light back

When you change modem (the internet box I presume) you should reset the AE to factory and redo the setup completely.
However if you merely want to stop the amber flashing.. find the cause.
Open the airport utility and click on the AE..
It will give you a list of faults or problems... fix each one and the light will turn green.
The most likely fault is double NAT.
That means the AE should be in bridge mode.. but if you list the fault we can give you further help with what to do to fix it if you cannot understand the instructions.
Apple does give a procedure to remove the problem although it may not always be the best solution.
eg Ignore.. the light will turn green.
Lately Apple is saying to use double NAT and ignore the problem.. I do not thing that is a good idea at all.
To bridge however may be easier after a full factory reset than trying to do a change to the setup.
If you run Yosemite.. then I recommend the following.. please read AE for TC.. (Time Capsule is what I mainly use but the setup is identical).
Factory reset universal
Power off the TC.. ie pull the power cord or power off at the wall.. wait 10sec.. hold in the reset button.. be gentle.. power on again still holding in reset.. and keep holding it in for another 10sec. You may need some help as it is hard to both hold in reset and apply power. It will show success by rapidly blinking the front led. Release the reset.. and wait a couple of min for the TC to reset and come back with factory settings. If the front LED doesn’t blink rapidly you missed it and simply try again. The reset is fairly fragile in these.. press it so you feel it just click and no more.. I have seen people bend the lever or even break it. I use a toothpick as tool.
N.B. None of your files on the hard disk of the TC are deleted.. this simply clears out the router settings of the TC.
Setup the TC again.
ie Start from a factory reset. No files are lost on the hard disk doing this.
Then redo the setup from the computer with Yosemite.
1. Use very short names.. NOT APPLE RECOMMENDED names. No spaces and pure alphanumerics.
eg TCgen5 and TCwifi for basestation and wireless respectively.
Even better if the issue is more wireless use TC24ghz and TC5ghz with fixed channels as this also seems to help stop the nonsense. But this can be tried in the second round.
2. Use all passwords that also comply but can be a bit longer. ie 8-20 characters mixed case and numbers.. no non-alphanumerics.
3. Ensure the TC always takes the same IP address.. you will need to do this on the main router using dhcp reservation.. or a bit more complex setup using static IP in the TC. But this is important.. having IP drift all over the place when Yosemite cannot remember its own name for 5 min after a reboot makes for poor networking. If the TC is main router it will not be an issue.
In your case bridge is most likely required.. and it is up to you how you deal with this one.. for now see if it is stable.. if it gives you issues come back and fix it.
4. Set IPv6 to link-local only on the computer..
This is strange one in that apple should have fixed this up ages ago.. but we are finding the auto setting even on Yosemite is still giving the wrong setup.

Unable to connect to Airport Extreme since installing Mountain Lion

Unable to connect to Airport Extreme since installing Mountain Lion. If I go to Finder > Shared I can see it listed but then when I go to connect to it won't. I can see it in Airport Utility and connect to the internet but when I try and connect to the base station to use my hard drive / printer it won't connect?
Tech Support tried saying it could be the devices attached don't have an update for them yet but doesn't explain why I can't connect to the base station. In their defence I can see it in airport utility so the base station does work with the OS X
However I've just tried connecting by an ethernet cable and connects fine?

Ok .
Power down the base station (Mine is connected to a 4 way so i down powered base station, printer and hard drive) powered back up and now when I go to finder then look at the shared section I can view my files on the base station.
Hope this helps

Imac will not connect to Airport Extreme when configured WPA/WPA2

Imac will not connect to Airport Extreme when configured WPA/WPA2
Posted: Jul 5, 2007 8:22 PM Reply
I just got my Imac to connect to the internet using my Airport Extreme but only by using WEP. I had my Windows XP SP2 machines connecting using WPA/WPA2 with no problem. The Imac will not connect using anything other than WEP, and 1 of the XP machines will not connect using WEP.(I have not tried the other XP machines) I had to set the Airport Extreme for an open network in order to let both computers access the shared hard drive and access the internet.
I don't know what the problem might be and would appreciate any suggestions.
MacBookPro, Imac Mac OS X (10.3.9) Fujitsu tablet PC, 2 XP desktops

hehe...on the visuals. I figured it out already, and I have the old airport card. However, I did a chat with Apple support and while we were chatting I found a USB adapter with MAC drivers which will work. It is:
Hawking Technology HWUG1A Wireless-G USB Adapter with Removable Antenna for Macintosh
Manufacturer Part# HWUG1A
That is the only adapter that actually does WPA/WPA2 that I can find that is for a Mac and not just an older USB that only does WEP. It surprises me that Apple does not have a USB product like this. Anyway, for $56 including shipping, I will have it by Monday or Tuesday. Pretty cool.
Thank you so much for your assistance. It is appreciated.
Lynn

Lost wifi connection with Airport Extreme.

Lost wifi connection with Airport Extreme. When I connect my modem directly to the computer I can access the internet, however as of this morning I am no longer able to access the internet via wifi on my airport extreme. I have been using airport extreme for 6 months or more and everything has been working fine.
When I diconnect my airport extreme and reconnect it I get wifi for 1-2 minutes working fine, but then i lose internet connection. According to airport Utility everything is setup and connected and working ok, but I still am not able to access any webpages over wifi.

I have the same issue, I'm getting droppeds from wireless constantly

VoIP (Internet Ready) phone connected to Airport Extreme?

Similar Messages

Maybe you are looking for