WAAS inline deployment options

Hi,
Can someone answer this basic question? I cant seem to find that much documentation on the inline modules.
Can you confirm whether or not devices can see each other on layer 2 across the two groups of an inline WAAS Ethernet module? i.e., if I have a router connected to the WAN of group 1 and another connected to the WAN of group 2, and the two routers are running HSRP (or even an ASA cluster), will they see each other correctly?
Thanks

Thanks for that. So if I had
Group1 = router1 - WAAS inline group1 - LAN switch
Group 2 = router2 - WAAS inline group2 - LAN switch
The routers would see each other through the WAAS and then the LAN switches (as if they were just connected to the switches), but wouldn't see each other directly across the WAAS module? Or you mean they don't see each other at all?
Cheers

Similar Messages

WAAS inline deployment

Hello All,
I'm deploying a couple of WAE-512's in "inline" mode for a customer. I have the configuration and seems pretty straight forward, looks like I just need to have the inlinegroup created and allow all VLAN's. I will also have a crossover connection from the gateway router to the WAE and straight through from the WAE to the core LAN infrastructure. Is there any other things I should look out for?, gotcha's,etc?. Just looking to see what other people experiences have been with this type of deployment. Thanks for your help!

Beware of duplex issues that can pop-up from time to time on FE connections, hard coding can help avoid that. I would also suggest portfast where applicable ie switchports.

WAAS Inline & HSRP Deployment

I'm running in a problem where auto-discovery is failing. We have remote-offices with one router and one wae in inline deployment, so far so good, this works perfect.
On the Main-Office we have two routers for redundancy, on the lan site we use hsrp.
Can I use both inline-cards two for each router ?
-----|- inlinegroup1---hsrp-router1-|--mpls
lan--|- inlinegroup2---hsrp-router2-|
or do I have to put both routers behind one pair of inline-card ?
-----|- inlinegroup1-|-hsrp-router1-|
lan--|- inlinegroup1-|-hsrp-router2-|--mpls
Kind Regards
-Lukas

Lukas,
If traffic for a connection flows asymmetrically through both inline groups, then CSCsk47177 can prevent optimization. This is schedule to be fixed in the next WAAS maintenance release.
Thanks,
Zach

WAAS - 2 arm inline deployment

I have a 2 arm deployment on a WAE-7371 with inline deployment at the core. Both WAN routers are connecting to the same MPLS cloud.
I found out when the traffic going out via the L0/W0 & return via the same int inlinegroup then it's fine. But if the return traffic come in via the W1/L1 then the traffic will be PT no peer/ Asymetric.
Does anyway face this before or am I missing something?
Thanks.
Edward

Hi Dan,
We have deployed more than 12 remote sites + 1 at DC for the client. Traceroute from both client & server end shows that the traffic is flowing through the WAE at both ends.
However, at DC's WAE with the 2 arm deployment, if traffic going out through the inlinegroup 1/0 (due to HSRP active router) and return via inlinegroup 2/0 then it will not optimised. So far there is 1 remote site traffic is routing this way (return via inlinegroup 2/0).
When I change the HSRP active router to force the out going traffic flowing through inlinegroup 2/0, this particular remote site will be fine & traffic is being optimized. But the rest of the 11 remote sites will be in Asymetric PT.
That's why I hope to find out why asymetric routes on a single WAE with 2 arm will not optimized.
Thanks & Regards,
Edward

"Deploy" Option Missing from VS

We just finished installing SharePoint 2013 RTM and VS 2012 for development purposes. I also installed the Preview 2 of the Office and SharePoint Dev Tools. The "Deploy" option which was previously present in Visual Studio to deploy SharePoint projects seems
to have disappeared. Oddly, I can however still tell the projects to Debug, which does the equivalent of Deploy + starts the debugger.
This is an extremely annoying issue as it is much faster to Deploy without starting the debugger. If anyone has any solution I'd be very appreciative. Thanks.

try these linsk:
https://louisliang.wordpress.com/2013/07/02/deploy-option-missing-from-visual-studio-2012-for-sharepoint-project/
https://social.msdn.microsoft.com/forums/sharepoint/en-US/c7b00231-680f-4fa1-b7ea-0008697c8122/visual-studio-2012-missing-deploy-option-on-build-menu
http://stackoverflow.com/questions/22944015/deploy-option-missing-visual-studio-2012
http://sharepoint.stackexchange.com/questions/49718/where-is-package-menu-item-in-visual-studio-2012
http://sharepoint.stackexchange.com/questions/82878/missing-deploy-button-visual-studio-2012
Please mark as answer if you find it useful else vote for it if it is close to answer..happy sharepointing

Where do I find the Package and Deployment options in CF Admin 8 and 9?

I've recently talked to a person at Adobe and found documentation on migrating using the Package and Deployment option to create CAR files. I just can't seem to find the menu options in my CF8 or CF9 Admin. I am running CF standard. I do have around 40+ datasources and a couple of dozen scheduled tasks that I need to move.
I just need someone to point out to me how to get to the Package and Depoymeny section.
Warmest regards,
David Miller

Standard doesn't have this feature. You need to be running Enterprise or Developer (see http://www.adobe.com/products/coldfusion/editions/).
You can revert to developer temporarily by removing your licence key, do the archive, put the key back in again ;-)
Adam

Deployment option under publish settings....

ello.
My problem has to do with under the DEPLOYMENT option in the
publish settings when your trying to import a video file, Im
wondering what the actionscript would perhaps look like if say I
want to take multiple videos and load them into one player. Im
trying to set up an empty flash player that when a user clicks on
say a thumbnail image the video corresponding to that image gets
loaded and autoplays in the player. Any ideas are
GREEEAAATTTLLLYY appreciated, cause im stuck.
Thanks, Joe.

don't import it unless you want a low-quality video that
takes a long time to load before it begins to display. use an flv
playback component or the video class or the video player
class.

SCCM 2012 Deployment Option Missing

Hey all,
I have a strange problem. I have build a custom task sequence (TS) to install operating systems on our computers. This TS runs scripts, installs applications and packages. I also have a front-end HTA that allows us to select certain software to be installed
and which OS image to apply. The issue I have is that every time the TS gets to the Run HTA part of the TS, which may I add is the very first step, the TS fails with error code 0x800700A1.
Now after several days of investigation I believe that the issue is that the deployment option is set to 'Download Content Locally when needed by running Task Sequence.' The problem, that is the only deployment option I can select. The other option, which
should be 'Access content directly from distribution point' is not even available. Researching this issue I found that I should make sure all my packages were copied to shares on the distribution points. So I did this, and to no avail. I made sure that a NAA
is set. Still, same error. A couple more things to note.
I am testing in a VMWare environment.
I have added the appropriate drivers to the boot image
Software deployments are working appropriately including the app catalog.
The NAA is a local admin on the distribution point.
All servers in the environment are Server 2012
So, I also began to think, "Well maybe SCCM doesn't like installing Applications from a TS and only handles packages...since applications are new to 2012."So I created a very simple TS that only installed an OS and still the same error. I added
the HTA just for kicks, same error. I have combed the smsts.log file and all of the errors keep leading me to dead ends or repeating steps I had already performed and then hoping for a different result. That's insane right?! If anyone has encountered this
error, and knows how to fix it, I would be forever grateful. If you would like the log file, I can accommodate. I just figured pasting a 4159 line long log file was a bit much.

>The problem, that is the only deployment option I can select.
The 'Run from DP' option is a Task Sequence-wide option in general, meaning that all the content would have to be duplicated to the package share in order to use it. Unless all the content is on the package share, this option is not available. The
only exception is the Apply OS step has its own setting.
If you have a step that uses content, but there is no formatted partition for the TS to download content to, you will receive an error. So, your first steps need to partition/format the drive if there is no usable partition before you try to download
content (like the files required for your HTA).
I usually steal the logic from the default MDT 2013 task sequence when integrated with ConfigMgr 2012 R2, even though I don't use MDT with ConfigMgr. The first real step is a format with this condition on it so it only runs if there isn't already a
local disk available:
If None of the Conditions are true:
select * from Win32_LogicalDisk where DriveType=3 and DeviceID != 'X:'
I hope that helps,
Nash
Nash Pherson, Senior Systems Consultant
Now Micro -
My Blog Posts
If you found a bug or want the product to work differently,
share your feedback.
<-- If this post was helpful, please click the up arrow or propose as answer.

NI Industrial Communications for EtherCAT 2.4 requires FPGA deployment option?

I am using NI Industrial Communications for EtherCAT 2.4, along with PXI real time target and some third party EtherCAT devices.
When I right clicked on my third party slave device in the LabVIEW project tree and selected Online Device State it started searching for NiFpgaBitfileGet_all.vi, then put up a message Cannot display selected category. I have temporarily fixed it by installing the FPGA deployment option. Will the fix still work once the 30-day evaluation period is over? I shouldn't need FPGA deployment option so why is there a dependency?

I do not have any NI slave devices. The third party device is a Micro-Epsilon confocalDT 2451 distance measurement probe. My controller is a NI PXI-8109, and I am using a PXI-8231 as the EtherCAT master. I am using LabVIEW 2011 with LabVIEW Real-Time 11.1. As an initial test setup I have just the one slave, as the attached project tree shows. I eventually want to have eight of these slaves, but that will need another thread. I have not had the opportunity to try "Revert to Default Personality" yet.
Paul
Attachments:
LV2.jpg ‏34 KB

Deployment Options

OWB newbie here - previous experience in custom built ETL. Multiple clients using our Oracle OLTP. Now need to build a warehouse that can be deployed to all clients but with options to switch on/off relevant components. Possibility/probability of moving into disparate source systems in future. So I have questions about deployment options.
1. Deploying to many targets when we cannot see the target. Brief reading tells me that we need to export the metadata, install the OWB client and runtime repository on site & deploy it all there? If all sources are Oracle, then the "here's your script, execute it every night" would be a simple deployment. Maybe with more disparate sources (flat files, etc), having to install OWB is a small overhead compared to the potential pain? Any advice welcome!
2. Core source schema is the same, but some modules may not exist on some client sites (e.g. different countries use different third party data). So invalid staging packages result in invalid parent packages? I suppose a possible workaround is to put the staging extract in dynamic sql so it always compiles and only run when the parameter is switched on. But then we're possibly losing some OWB benefits (source tracing, etc). Are there other options for this sort of thing?
Thanks for your help!

Or you could also assume that you have to do the initial leg work...
Analyze all sources which could be different based on the country, region, etc.
But that's not a problem because you can handle that using custom view in your integration layer to make all sources look at some point idential
Then you could load all this wonderfull data in your target DW using the same processes ....

Changing the Task Sequence Deployment Options via script

Hi all,
I am fairly new to SCCM 2012 scripting/SDK and couldn't find any helpful examples how to change the deployment options of task sequences by using a script.
The problem is: we have got a significant number of TS that have the deployments set to "Download content locally when needed by running task sequence".
I have to change this setting to "Download all content locally before starting task sequence".
Afterwards I need to create a list of all changed TS Deployment options and also a list of current settings of all TS Deployment options.
Therefore I would need a script that can read and set this particular option of the TS.
Does anybody have a script that can do such tasks? Any help is highly appreciated.
Btw, I am not picky, I can handle WMI, SQL, VBS, PowerShell, .Net Code (vb.net or c#). Whatever you have handy would be quite helpful.
Many thanks
Amir

Hi,
The Set-CMTaskSequence -DeploymentOption could help you change this setting.
Set-CMTaskSequence
Best Regards,
Joyce Li
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

RDS gateway deployment options with no DMZ

Hello
I have setup an RDS server that is running nicely and I now need to deploy it externally. I have read through the deployment guides which state that you should deploy the gateway in a DMZ. My problem is that I do not have a DMZ and my firewall does not have
a DMZ port or an option to assign different IPs to different internal interfaces. What would be the best deployment option if no DMZ is available?

Hi,
Thank you for posting in Windows Server Forum.
Agree with “Guna” comment, you can setup RD Gateway for accessing the server externally. For that you can refer following link to setup RD Gateway.
1. How To Work with RD Gateway in Windows Server 2012
2. Deploying Remote Desktop Gateway RDS 2012
Hope it helps!
Thanks.
Dharmesh Solanki

Connect 9 Managed Services Deployment Option

I have some questions about the managed services deployment option for Adobe Connect 9
Does the AC9 A managed services deployment include the cost of running on AWS or do I have to purchase that separately?
Can I upgrade from AC8 on premises to a managed deployment?
Can it be merged with some on premises installs of Connect and/or Connect Edge for a customised install?
Does it scale based on user demand or as a result of consultation between AC support and Client or not at all?
Does it scale from simple install to clustered version by simple I mean 1 Connect, server and associated support servers kind of setup to a more robust setup involving edge servers and clustering?
Can I modify the deployment or have it modified for me during the life of the deployment e.g. add SSO a few months after 1st deployment?
Is there a minimum number of host licences that need to be purchased?
Can I specify data location rules e.g. all data resides within EU datacentres?
Can extra features like Events or Courses be added to the managed deployment?
Is it only AWS platform that is avaialble for the managed services?
What kind of feedback on usage/performance of the deployment environment does the client get? (can the client access the logs, resource usages of the AC servers or is access only via the Connect web UI and the Adobe Support ticketing system)

1. You are paying an annual fee, there shouldn't be additional costs unless you increase licensing. The accounts are all deployed on AWS, I believe.
2. Yes, it will cost money to migrate the data, but it can be done.
3. [Updated] This is probably possible if you throw enough money at it.
4. The account can scale as needed. This is more of an issue around licensing though. Maybe I'm interpreting the question wrong.
5. The setup of Edge Servers and Clustering is on Adobe. You purchase the account and licensing, they get their hands dirty to configure setup. I know there is clustering for fail over scenarios.
6. Yes, the account is like having a licensed deployment, only you can call Adobe and yell at them when it doesn't work. SSO, SSL, additional licenses can all be added when needed.
7. There is a minimum cost, so I guess licensing could be tied to that, but it would vary based on the account needs.
8. Probably, that is best answered by the ACMS team.
9. Yes, just purchase the licensing.
10. AWS, I believe, is the only platform offered by ACMS.
11. You should have full access to the logs (or at least be able to request them at any point, or set up a recurring delivery of the logs/information). Think of this as a licensed deployment, you will have all the info you get by running your own server. I don't know a web UI that will deliver this info, but there may be something that Adobe can put in place. You should have a dedicated number of a person or team to reach out to for your ACMS deployment. You shouldn't need to start at 800-42-ADOBE.

WAAS Inline Adaper and Microsoft NLB (ISA Server Array)

Hi
I would like to place a waas device with 4-port inline adapter between a MS ISA Firewall and the LAN switches. The ISA are unfortunately forming an array and using NLB which causes the switches to do unknown unicast flooding.
            / Switch A --------------- LAN0   WAN0 ------------ ISA1 ------------- Switch C ---------- Router A
LAN -- |            |                               WAAS                        Array                        |       HSRP     |
            \ Switch B --------------- LAN1   WAN1 ------------ ISA2 ------------- Switch D ---------- Router B
Will the WAAS get problems since it is seen all the traffic on both inline groups? Is this setup possible?
kind regards
Tobias

Gary,
Yes you just need to configuring your firewall to allow TCP options (specifically option 33 (0x21 in HEX)), then configure the WAEs for directed mode.
The firewall will see a TCP 3-way handshake at first so the two WAEs can auto discover each other and negotiate a UDP directed mode tunnel.
Once the auto discovery phase is complete traffic traffic sent over the WAN side of the connection will be encapsulated in the UDP 4050 tunnel (so your firewall must allow this traffic through as well).
Please see the configuration guide section on directed mode here which explains in more detail, and let me know if you have other questions.
http://www.cisco.com/en/US/docs/app_ntwk_services/waas/waas/v421/configuration/guide/network.html#wpxref53362
Cheers,
Mike

Waas inline in L2 environment

Hi,
A new WAAS installation is planed. The customer has 3 sites with one WAAS on each. On each site, there is no core layer. The L3 device is the ISP router. So, the WAAS will be plugged via inline interfaces between the ISP router and a switch. The WAAS will received all L2 broadcast from the LAN. There is no L3 point-to-point dedicated network between the router and the switch.
Is this scenario could be an issue ?
Rgds.

Wow, cant believe noone answered this for two years!
I´m having the similar WAAS deployment, check this link out:
http://www.cisco.com/en/US/prod/collateral/contnetw/ps5680/ps6870/white_paper_C11-560131.pdf

WAAS inline deployment options

Similar Messages

Maybe you are looking for