Wait for note recording...

i am a noob. i admit. this is my first night with logic and i am having a hard time finding a "wait for note" recording option. i found where to change the count in but i was needing a wait for note because i am recording something previously recorded on my fantom. any help would be appreciated.

Well it is another beautiful day here in southern California. The smoke is so thick I can't even see the mountains a few miles away. Now that wind has shifted, It's all coming our way
Anyway, You have a few options to get your beats from the Fantom into Logic. Now if you want to get the midi notes into Logic. After you get a midi chord hooked up from the out of the Fantom to the input of your midi interface, and you can see you are getting midi signal, try this
1st you could just make sure both Logic and the fantom are the exact same tempo, set Logic to record and as close to a down beat as you can press start on the Fantom. After you record the part open either the Event list or the the Piano roll editor, selects all, and just drag your first note to be right on the beat, as long as all note are selected all will line up. If you have any timing drift and some notes are not lining up to the grid you can always quantize them
2nd you can always slave logic or the fantom to MTC (midi time code) so that they lock up real tight. how to do this is described in chapter 36 of the manual. if you want to slave logic to the Fantom you have to do it in MTC because Logic 8 no longer slaves to midi beat clock. After you look over the manual and you need further help on this ask.
If you have more that one midi channel that you want to send to logic, you can send them all at the same time and have logic separate them. Switch on the File > Project Settings > Recording > “Auto demix by channel if
multitrack recording” option. Then create as many tracks in logic that you have in the Fantom and set each Logic track to match the midi channels. then record enable them all, pressing the record button on each track. Chapter 14 page 382 explains multi-track midi recording.
You can also record all midi channels at once on to one track, and then from your region menu select "split/demix> demix by event channel" and that will separate all midi channels on to tracks
Anyway, this will get you started, let me know if you need more help
Don

Similar Messages

Where is the wait for note mode in logicstudio

Can anyone please tell me where the wait for note mode is in logicstudio, or how to enable it "ie hit record button, and it waits for me to hit a midi note before it starts to record.
Anyone out there with the info

that is so wack, i cant believe this is ok with everyone, i need wait for note mode , it might be a mental thing but dam, thanks for the info, something so simply

Update of jlabel does not happen when i wait for thread to finish (join())

gurus please help.
I have a main application which in actionevent calls a thread, that thread calls parent method to update ths status in jlabel, but when i use thread.join() to wait for process to complete, the jlabel does not get updated, please tell me how can i update the jlabel, i have to wait for thread to finish and during run i need to update the jlabel.
thanks

hi camickr and gurus:
here is the code:
notice after pressing the Process button, the label is being updated but its not working. I called the processnow() method directly and also by thread, but in thread I have to wait until it finishes using join() but still does not work, please help. Thanks
package label;
import java.awt.*;
import java.awt.event.*;
import java.util.*;
import java.text.*;
import javax.swing.border.*;
import javax.swing.*;
import javax.swing.table.*;
import javax.swing.event.*;
public class thePanel extends JDialog {
private DefaultTableModel tableModel = null;
private JTable theTable = new JTable();
private JScrollPane scrollPane = new JScrollPane();
JPanel tPanel = new JPanel();
private Border mainBorder;
private BorderLayout borderLayout1 = new BorderLayout();
private BorderLayout borderLayout2 = new BorderLayout();
private BorderLayout borderLayout3 = new BorderLayout();
private BorderLayout borderLayout4 = new BorderLayout();
private JPanel statusPanel = new JPanel();
private JPanel buttonPanel = new JPanel();
private JPanel lowerPanel = new JPanel();
private JLabel statusBar = new JLabel();
private JButton processButton = new JButton("Process");
public JButton closeButton = new JButton("Close");
boolean image = true;
theProcess processThread;
Vector tableData = new Vector();
ImageIcon Image = new ImageIcon("image.gif");
ImageIcon oImage= new ImageIcon("oimage.gif");
boolean errorOcurred=false;
String statusMessage;
public thePanel() {
 try {
 jbInit();
 } catch(Exception e) {
 e.printStackTrace();
private void jbInit() throws Exception {
 tPanel.setPreferredSize(new Dimension(800,424));
 mainBorder = new TitledBorder(BorderFactory.createEtchedBorder(EtchedBorder.RAISED)," ");
 statusPanel.setBorder(BorderFactory.createEtchedBorder());
 tPanel.setBorder(mainBorder);
 tPanel.setLayout(borderLayout1);
 scrollPane.getViewport().add(theTable, null);
 tPanel.add(scrollPane, BorderLayout.CENTER);
 // status
 statusPanel.setLayout(borderLayout2);
 statusPanel.setBorder(BorderFactory.createEmptyBorder());
 statusBar.setAlignmentX((float) 0.5);
 statusBar.setBorder(BorderFactory.createLoweredBevelBorder());
 statusBar.setMaximumSize(new Dimension(600, 21));
 statusBar.setMinimumSize(new Dimension(600, 21));
 statusBar.setPreferredSize(new Dimension(600, 21));
 statusPanel.add(statusBar, BorderLayout.SOUTH);
 // buttons
 processButton.setPreferredSize(new Dimension(70,25));
 processButton.addActionListener(new java.awt.event.ActionListener() {
 public void actionPerformed(ActionEvent e) {
 process_actionPerformed(e);
 closeButton.setPreferredSize(new Dimension(70,25));
 buttonPanel.setLayout(borderLayout3);
 buttonPanel.setBorder(BorderFactory.createRaisedBevelBorder());
 buttonPanel.add(processButton,BorderLayout.WEST);
 buttonPanel.add(new JPanel());
 buttonPanel.add(closeButton,BorderLayout.EAST);
 // lower panel
 lowerPanel.setLayout(borderLayout4);
 lowerPanel.setBorder(BorderFactory.createEmptyBorder());
 lowerPanel.add(statusPanel, BorderLayout.WEST);
 lowerPanel.add(buttonPanel, BorderLayout.EAST);
 tPanel.add(lowerPanel, BorderLayout.SOUTH);
 theTable.setAutoCreateColumnsFromModel(true);
 theTable.setColumnSelectionAllowed(false);
 theTable.setSelectionMode(ListSelectionModel.MULTIPLE_INTERVAL_SELECTION);
 theTable.getTableHeader().setReorderingAllowed(false);
getContentPane().add(tPanel);pack();
 getinfo();
show();
private void prepairTable(){
 tableModel = new DefaultTableModel(){
 public boolean isCellEditable(int row, int col)
 { return false; }};
 tableModel.addColumn("text 1");
 tableModel.addColumn("text 2");
 tableModel.addColumn("text 3");
 tableModel.addColumn("text 4");
 tableModel.addColumn("text 5");
 theTable.setModel(tableModel);
} // end method (prepairTable)
public void refreshTable() {
 prepairTable();
public void getinfo() {
 try {
 refreshTable();
 tableModel.addRow(new Object[]{"3465465555","0123456789",new Date(1135022905196L),"0100000","errror message","sssssss"});
 tableModel.addRow(new Object[]{"8949344562","0324354549",new Date(1134511763683L),"0166600","errror mes666e","ddddddd"});
setStatusMessage("ready to process, select record and click Process button to process record");
 errorOcurred = false;
 } catch (Exception ex) {
 errorOcurred = true;
 ex.printStackTrace();
 } // End try
private void process_actionPerformed(ActionEvent e) {
 try {
 if(theTable.getSelectedRows().length > 0) {
// processThread = null;
// processThread = new theProcess(this);
// processThread.start();
processnow();
 System.out.println("........finished now.........");
 } else {
 } catch (Exception ex) {
 ex.printStackTrace();
public void processnow() {
 try {
 int[] selectedRows = null;
 int totalSelected = 0;
 setStatusMessage("processing " + totalSelected + " selected records...");Thread.sleep(1500);
 selectedRows = theTable.getSelectedRows();
 totalSelected = selectedRows.length;
 for(int i = 0; i < totalSelected ; i++){
 setStatusMessage("processing " + (i+1) + " of " + totalSelected + " selected records...");
 System.out.println(".......................row: "+selectedRows);
Thread.sleep(2500);
System.out.println("........fins...........");
errorOcurred = false;
} catch (Exception ex) {
errorOcurred = true;
ex.printStackTrace();
} // End try
public void setStatusMessage(String message) {
statusMessage=message;
SwingUtilities.invokeLater(new Runnable() {
public void run() {
if(image)
statusBar.setIcon(Image);
else
statusBar.setIcon(oImage);
statusBar.setText(statusMessage);
statusBar.update(statusBar.getGraphics());
public static void main(String[] args){
new thePanel();
} // class
package label;
import java.lang.Runnable;
public class theProcess implements Runnable {
private thePanel parent;
public theProcess(thePanel xparent){
parent = xparent;
} // end constructor
public void start() {
try {
Thread thisThread = new Thread(this);
thisThread.start();
thisThread.join();
} catch(Exception ex) {
ex.printStackTrace();
} // end method (start)
public void run(){
try {
parent.processnow();
} catch (Exception ex){
ex.printStackTrace();
} // end try
} // end method (run)
} // end class

'&' character erratic in SQL (sometimes waits for input, sometimes does not)

Hi everyone,
I have a C program using OCI which sends insert, update and delete statements to an Oracle database. Now there was a case when I tried to insert a statement say INSERT INTO EMP(EMPNO, ENAME) VALUES(7000,'Jack & Jill'). This statement was hanging when I sent it once and then I realised that & is a special character which causes the statement to wait for an input. So we had to use escape characters probably so that the statement would not hang.
Sometime later (a day later) I deleted the record and put in the same one again and this time it worked without hanging.
Is there some reason why this can be do. The OCI code has not changed, but I do not know if the Oracle DBAs did any changes to the server to accept & as okay. The DBAs say that they are not aware of any changes made.
Does anyone know why this can happen? Or is there someway this '&' issue can be sorted out?
Thanks
Kind Regards
Aby Philip

Hi !!
I really could not figure out why it had gone thru the second time..
A way o get around it would be to modiy ur sql like :-
insert into .... ('sini'||'&'||'somakumar');
Has to do the work ;
Reagrds
Sini Somakumar

'&' character in SQL behaves erratic (waits for input sometimes does not)

Hi everyone,
I have a C program using OCI which sends insert, update and delete statements to an Oracle database. Now there was a case when I tried to insert a statement say INSERT INTO EMP(EMPNO, ENAME) VALUES(7000,'Jack & Jill'). This statement was hanging when I sent it once and then I realised that & is a special character which causes the statement to wait for an input. So we had to use escape characters probably so that the statement would not hang.
Sometime later (a day later) I deleted the record and put in the same one again and this time it worked without hanging.
Is there some reason why this can be do. The OCI code has not changed, but I do not know if the Oracle DBAs did any changes to the server to accept & as okay. The DBAs say that they are not aware of any changes made.
Does anyone know why this can happen? Or is there someway this '&' issue can be sorted out?
Thanks
Kind Regards
Aby Philip

Aby,
I have a similar problem when running scripts in SQL*PLUS. In this case I resolved problem using concat (||), like this example
<code>
INSERT INTO EMP(EMPNO, ENAME) VALUES(7000,'Jack '||'&'||' Jill')
</code>
Sergio
Hi everyone,
I have a C program using OCI which sends insert, update and delete statements to an Oracle database. Now there was a case when I tried to insert a statement say INSERT INTO EMP(EMPNO, ENAME) VALUES(7000,'Jack & Jill'). This statement was hanging when I sent it once and then I realised that & is a special character which causes the statement to wait for an input. So we had to use escape characters probably so that the statement would not hang.
Sometime later (a day later) I deleted the record and put in the same one again and this time it worked without hanging.
Is there some reason why this can be do. The OCI code has not changed, but I do not know if the Oracle DBAs did any changes to the server to accept & as okay. The DBAs say that they are not aware of any changes made.
Does anyone know why this can happen? Or is there someway this '&' issue can be sorted out?
Thanks
Kind Regards
Aby Philip

HSDIO conditionally fetch hardware compare sample errors (script trigger to flag whether or not to wait for software trigger)

I am moderately new to Labview and definitely new to the HSDIO platform, so my apologies if this is either impossible or silly!
I am working on a system that consists of multiple PXI-6548 modules that are synchronized using T-CLK and I am using hardware compare. The issue I have is that I need to be able to capture ALL the failing sample error locations from the hardware compare fetch VI... By ALL I mean potentially many, many more fails than the 4094 sample error depth present on the modules.
My strategy has been to break up a large waveform into several subsets that are no larger than 4094 samples (to guarantee that I can't overflow the error FIFO) and then fetch the errors for each block. After the fetch is complete I send a software reference trigger that is subsequently exported to a scriptTrigger that tells the hardware it is OK to proceed (I do this because my fetch routine is in a while loop and Labview says that the "repeated capbility has not yet been defined" if I try to use a software script trigger in a loop).
This works fine, but it is also conceivable that I could have 0 errors in 4094 samples. In such a case what I would like to do is to skip the fetching of the hardware compare errors (since there aren't any) and immediately begin the generation of the next block of the waveform. That is, skip the time where I have to wait for a software trigger.
I tried to do this by exporting the sample error event to a PFI and looping that PFI back in to generate a script trigger. What I thought would happen was that the script trigger would get asserted (and stay asserted) if there was ever a sample error in a block, then I could clear the script trigger in my script. However, in debug I ended up exporting this script trigger back out again and saw that it was only lasting for a few hundred nanoseconds (in a case where there was only 1 injected sample error)... The sample error event shows up as a 1-sample wide pulse.
So, my question is this: is there a way to set a flag to indicate that at least one sample error occurred in a given block that will persist until I clear it in my script? What I want to do is below...
generate wfmA subset (0, 4094)
if scriptTrigger1
clear scriptTrigger1
wait until scriptTrigger0
end
clear scriptTrigger0
generate wfmA subset (4094, 4094)
I want scriptTrigger1 to be asserted only if there was a sample error in any block of 4094 and it needs to stay asserted until it is cleared in the script. scriptTrigger0 is the software trigger that will be sent only if a fetch is performed. Again, the goal being that if there were no sample errors in a block, the waiting for scriptTrigger0 will not occur.
I am probably going about it all wrong (obviously since it doesn't work), so any help would be much appreciated!

Please disregard most of my previous post... after some more debug work today I have been able to achieve the desired effect at slower frequencies. I did straighten out my script too:
generate wfmA
if scriptTrigger1
clear scriptTrigger0
wait until scriptTrigger0
end if
generate wfmA
scriptTrigger1 = sample error event flag
scriptTrigger0 = software trigger (finished fetching error backlog in SW)
However, I am still having a related issue.
I am exporting the Sample Error Event to a PFI line, looping that back in on another PFI line, and having the incoming version of the Sample Error Event generate a script trigger. My stimulus has a single injected sample error for debug. For additional debug I am exporting the script trigger to yet another PFI; I have the sample error event PFI and the script trigger PFI hooked up to a scope.
If I run the sample clock rate less than ~133MHz everything works... I can see the sample error event pulse high for one clock period and the script trigger stays around until it is consumed by my script's if statement.
Once I go faster than that I am seeing that the script trigger catches the sample error event occasionally. The faster I go, the less often it is caught. If I widen out the error to be 2 samples wide then it will work every time even at 200MHz.
I have tried PFI0-3 and the PXI lines as the output terminal for the sample error event and they all have the same result (this implies the load from the scope isn't the cause).
I don't know what else to try? I can't over sample my waveform because I need to run a true 200MHz. I don't see anything that would give me any other control over the sample error event in terms of its pulsewidth or how to export it directly to a script trigger instead of how I'm doing it.
Any other ideas?

Iphone 4s not syncing to iTunes *waiting for changes to be applied*

I have a brand new iphone 4s that wouldnt sync with my pc desktop and i recently got a new mbp and the same thing is happening an error keeps popping up in Itunes after the 2nd step of syncing and it says waiting for changes to be applied. Its really frustrating i restored my phone and it did nothing for the syncing just deleted all my apps...and ive researched these problem before and its obvioius a big occurance with other users and apple has done nothing?!?! wth !! and i have no voice memos on my phone so there is nothing to delete for those that have solved their issue that way....So if someone has a solution to help me sync my iphone 4s to my mbp i would greatly appreciate since obviously apple does not care to fix this issue!!!! terrible..

also tried to wifi sync and nothing ...

Quicktime plugin does not load on FireFox 4.01 says Waiting for Video

When i go to Apple Trailers and view a trailer the popout box opens but message in window is " Waiting For Video ". Have re-installed quicktime still doesnt work, works ok in IE 8 still.
== This happened ==
Every time Firefox opened
== since installing Firefox 4.1

You are using the '''first beta release''' of Firefox 4; it is not meant for general public use. Not all plugins may yet be updated. Only experienced testers should be using that new beta release. When using an early beta release of any application, you can expect problems. You can go to the Quicktime site and/or Quicktime forums to see if there is information there concerning the compatibility of your version of Quicktime with Firefox 4.
'''''Other Issues''''': ~~red:You have installed plug-ins with known security issues. You should update them immediately.~~
'''Install/Update Adobe Reader for Firefox (aka Adobe PDF Plug-In For Firefox)''': your ver. 9.3.2; current ver. 9.3.3 (important security update release 06-29-2010; see: http://www.adobe.com/support/security/bulletins/apsb10-15.html)
~~red:Check your version here~~: http://www.mozilla.com/en-US/plugincheck/
See: http://support.mozilla.com/en-US/kb/Using+the+Adobe+Reader+plugin+with+Firefox#Installing_and_updating_Adobe_Reader
''You may be able to update from the Adobe Reader installed on your system'' instead of going to the Adobe site and downloading. Start > Program Files, find and click Adobe Reader to open, click Help, click Check for Updates.
''If you go to the Adobe site to download the current Adobe Reader:''
-'''use Firefox to download''' and '''SAVE to your hard drive''' (save to Desktop for easy access)
~~red:-See the images at the bottom left of this post to see the steps to take on the Adobe site~~
-exit Firefox (File > Exit)
-check to see that Firefox is completely closed (''Ctrl+Alt+Del, choose Task Manager, click Processes tab, if "firefox.exe" is on the list, right-click "firefox.exe" and choose End process, close the Task Manager window'')
-double-click on the Adobe Reader installer you just downloaded to install/update Adobe Reader
*'''NOTE: On Vista and Windows 7''' you may need to run the plugin installer as Administrator by starting the installer via the right-click context menu if you do not get an UAC prompt to ask for permission to continue (i.e nothing seems to happen). See this: http://vistasupport.mvps.org/run_as_administrator.htm
*'''NOTE for IE:''' Firefox and most other browsers use a Plugin. IE uses an ActiveX version. To install/update the IE ActiveX version, same instructions as above, except use IE to download the ActiveX installer. See: [[ActiveX]]
*Also see: http://kb.mozillazine.org/Adobe_Reader ~~red:'''''AND'''''~~ [[How do I edit options to add Adobe to the list of allowed sites]]

Text Entry not waiting for entry before continuing

Captivate 4
I'm trying to add a TEB where the user will need to enter the correct text before moving to the next slide. I would like it to continue as soon as they user types the correct entry. The problem is that the slide doesn't pause to wait for the entry - it continues to the next slide without anything being typed or a click. ??
I have the correct text listed in the 'Correct Entries' box and have it set to 'go to next slide' for 'On success'. Under 'Options', I have it set to 'Validate User Input'. I do not have any hint or caption buttons, and I am not showing a 'submit' button.
Can someone tell me how to get it to pause the training to wait for the user to enter the correct text?
Screen shots below.
Thanks in advance,
D

Hi there
Indeed there is!
You enable the Button in the properties. This will place an associated button next to the field.
What's that you are asking? You don't want a button?
Well, nobody said you actually have to SEE the button! Just double-click the button and its properties will show. Choose Transparent Button and configure it so it's invisible. Then you configure the other "1" for the Button press!
Cheers... Rick
Helpful and Handy Links
Captivate Wish Form/Bug Reporting Form
Adobe Certified Captivate Training
SorcerStone Blog
Captivate eBooks

TS4268 hi my imessage isnt working so I turned off imessage and now its been saying "waiting for activation" and has been for a long while now? can you please help me!!! Also saying that my apple ID password is inccorrect when its not!

Hi,
My imessage isnt working so I turned off imessage and now its been saying "waiting for activation" and has been for a long while now? Also saying that my apple ID password is inccorrect when its not! Can anyone help me?
Thanks

While we all have MacBooks in this forum most of us don’t have Lion. There's a Lion Support Community where everybody has Lion.You should also post this question there. https://discussions.apple.com/community/mac_os/mac_os_x_v10.7_lion

It is so nice spending 2 hours on a phone to be hung up upon waiting for a supervisor. After being told the day before I would get a call when the customer service representiave started her shift at 7pm to give me more answers. I do not like to be stuck w

What a frustrating experience I have had trying to get away from This phone and Plan. I just want to down grade this phone. What difference does it make to you here? All VZW will do is re certify the phone and give it to someone else. I just would like to down grade to a cheaper phone and do away with android os. I still have the same issues with the phone as I did with my other one within a hour of re activating it. I should have no issues with the os it is flawed and should not happen. I am sorry to say but The blackberry OS is a lot more stable. There may not be as many apps but it is more productive and being able to multi task is a lot more needed on a phone. I was told yesterday I would get a call back today at 7pm when this tech support lady would start her shift to give me my options and she did not call. Making me call at 930pm today and after talking to someone I waited for 45 minuets to be hung up on. That is a real great way to treat a customer and make things better. I just want away from the Andriod OS. What difference does it make to you as a company to make a customer happy who was with you since 08 and having a second device added on to the account? What Poor way to treat someone to make them happy with all the profits you have and can't give anything back to a customer.

What a frustrating experience I have had trying to get away from This phone and Plan. I just want to down grade this phone. What difference does it make to you here? All VZW will do is re certify the phone and give it to someone else. I just would like to down grade to a cheaper phone and do away with android os. I still have the same issues with the phone as I did with my other one within a hour of re activating it. I should have no issues with the os it is flawed and should not happen. I am sorry to say but The blackberry OS is a lot more stable. There may not be as many apps but it is more productive and being able to multi task is a lot more needed on a phone. I was told yesterday I would get a call back today at 7pm when this tech support lady would start her shift to give me my options and she did not call. Making me call at 930pm today and after talking to someone I waited for 45 minuets to be hung up on. That is a real great way to treat a customer and make things better. I just want away from the Andriod OS. What difference does it make to you as a company to make a customer happy who was with you since 08 and having a second device added on to the account? What Poor way to treat someone to make them happy with all the profits you have and can't give anything back to a customer.

Process chain Error: This AND process is not waiting for event RSPROCESS

Hi All,
I am facing an error in the process chain in PRD.
Error message: This AND process is not waiting for event RSPROCESS.
We had a process chain which had two sub chains which run parallel and below of this we had AND process type and below of the AND process we had 4 more jobs.
Once the two subchains got successfully loaded, the and process should turn to green and further 4 jobs should start.
It is a daily load , it worked fine from past years,but suddenly the AND processtype is getting failed.The thing is in the two subchains if one got completed, the AND process process is not waiting for 2nd subchain to get completed.The AND process is turning to RED (status: cancelled) . I tried to repeat the AND process once after above 2 subchains loaded, but it didnt worked.
And i removed the existing AND process and created a new one and placed it in same place and activated and schedules again.but still it is getting failed with same error.
Thanks in advance,
Sai Chand.S

Hi,
If you did any transports related to that metachain we face similar kind of issues.
not only the AND process , we need to remove all the process before executing the AND process and create it again.
It helps you, you said your in production So you should take the proper approvals and do it.
Regards,
Yerrabelli.

When syncing after recent update, sync is stuck at "Step 4 of 4" "Waiting for changes to be applied" and will not complete, even after hours. How can this be fixed?

I completed the most recent software update for both iTunes and iPhone recently. I am now trying to sync my iPhone to add newly purchased audiobooks and the sync remains stuck at "Step 4 of 4" with the message "Waiting for changes to be applied" I have tried everything to correct this. When sync is cancelled a failure to sync message is generated. Any ideas????

Alright, so I reset my computer and suddenly it then recovered. Other times it wouldn't recover after resetting the computer, so I have no idea how it happened. I just restarted the computer lots of time and finally it worked.
Okay, back to square one. Now to transfer music, I tried my previous acknowledgable solutions but they didn't work. The iPod touch does not feature a hard-disk mode, and windows media player doesn't support iPods.
I've tried multiple programs to transfer music but none of them work properly and keep giving me error codes. So my iPod still gets stuck at Step 4: Waiting for changes to be applied or whatever it said.
Thanks in advance ._. (Please help)
p.s - Apple is useless. If I don't get steady answers tomorrow I'm going to end up calling them and get this problem fixed first hand. Second hand? I don't know, over the **** phone.
juiceb0xk signing out for the night. Bye. >:(

Material Description is not displaying for few records in Report

Dear Experts,
Report Material Description is not displaying for few records in Bex Report but for records it is coming and even the heading of the material Description is also not coming for this report.
Cud u plz suggest a good solution for it.
Regards,
Sai Phani.

Hi Phani,
For the text of the material in records, check if there is text maintained for that material in the master data. also try by changing the text to medium text and long text.
regarding header, you will have same heading for key and text, you may use Materail ID / Description as the heading if you want.
regards,
Rk.

HT204406 Hello, I have songs that show they are "Waiting" for download from the cloud but they are greyed out. Some songs in one album are done others in the same album will not download. It is not a time function because i have been working on this for

Hello, I have songs that show they are "Waiting" for download from the cloud but they are greyed out. Some songs in one album are done others in the same album will not download. It is not a time function because i have been working on this for weeks. I have allowed my compter to run for days and the songs are still not accessible. I have a Match subscription and Match is working. If I click on the "Genre" link the greyed out songs show that they are ready for download from the cloud but I cannot download them. I have downloaded over 1500 other songs, so I am trying to understand what is going on here. I would appreciate any help anyone can give me.
Thanks

I did think about that and if I have to I will do that, however there are about 50 songs. I have closed and reopened iTunes several times and I am sure that I have the latest version. It fails right away but I can click on the cloud download icon and download the song that it failed on ... therefore it is not that song "or any one song" causing the issue. Any ideas?

Wait for note recording...

Similar Messages

Maybe you are looking for