WakeOnLan (WOL ) through Cisco 870 not working

Hi,
I need to allow WOL packets through a Cisco 870W router. Its running IOS version 12.4(9)T
The WOL magic packet will be coming from VLAN1 (192.168.2.0/24) and going to FastEthernet4 (192.168.6.0/24).
The WOL application sends UDP packets on port 9
Here are the relevant running-config sections
interface Vlan1
ip address 192.168.2.30 255.255.255.0
no ip redirects
no ip unreachables
ip directed-broadcast
no ip proxy-arp
ip route-cache flow
ip tcp adjust-mss 1452
interface FastEthernet4
ip address 192.168.6.1 255.255.255.0
ip helper-address 192.168.2.1
ip helper-address 192.168.2.10
no ip redirects
no ip unreachables
ip directed-broadcast
no ip proxy-arp
ip route-cache flow
duplex auto
speed auto
no cdp enable
I've also found documents recommending I add
ip forward-protocol udp 9
which I've added and still nothing. Can anyone tell me why this is not working?
Thank you.
Vic.

Hi Vic,
The Small Business Support Community is limited to Cisco Small Business Products.
Your question below relates to a Cisco Classic Product for small offices which our community would not be able to help you with.
The best area for you to post your question would be at the Cisco NetPro forums: http://forums.cisco.com/eforum/servlet/NetProf?page=main
Best regards,
Cindy
Cindy Toy
Small Business Community Manager
Customer Advocacy
Cisco Systems, Inc.

Similar Messages

Since I installed the new OS X Lion, the iCal syncing through iTunes is not working properly.

Since I installed the new OS X Lion, the iCal syncing through iTunes is not working properly.
When I sync my MacBook Pro with my iPhone and iPad, the events set in both devices (iPhone & iPad) are not transfered to the iCal on my labtop. Events created in both devices are transfered and copied betwen them when I sync them with the iTunes app (through the MacBook Pro) but they are not trasfered/copied into the labtop (iCal). The events created in the iCal (on my MacBook) are tranfered to the devices as two events on same hour. One, with the description created on the iCal, and the other as a New Event (no description). This is happening since I installed the new OS X Lion last week.
I file a report and talked with an Apple Support Representative, but they could not help me. They have not receive any other reports on this matter. Do someone has confronted this issue. I need to find out how to solve this problem.
Regards,
JAD

Hi Sydness,
Thank you very much for your help. It just worked fine. I have 4 macs in my company for 25 years (one is updated each year), and it is the first time I could not solve a problem for weeks. It gave me the opportunity to join this great community.
Charles
Sydness wrote:
I reset my SyncServices and the calendar sync worked perfectly after that.
I followed the instructions found here:
http://support.apple.com/kb/TS1627?viewlocale=en_US
Mac OS 10.7.1 - MacBook

The two finger cycle through apps does not work?

Hello,
I don'nt know what is wrong, but it seems that the two finger gesture allowing to cycle through apps does not work for me. I am using a standard mac Bluetooth mouse.
Can anyone help me with this?
Thank you
Sebastien Dion
from Quebec city, Canada

Download a free app. It reauthorizes your device for use of your apple id.

License Key from Cisco is NOT Working.

Hello All,
Device: Cisco Wireless Controller 2504 (AIR-CT2504-K9)
We had purchased an Access Point Upgrade License for our Wireless Controller and when I try to upload the key to the WLC, I get a message that there were no valid Licenses found. We purchased the License from our 3rd party Cisco provider and our Rep had sent me 2 PAK numbers the other day for the Licenses. So I went on Cisco's site and entered the PAK Numbers (*there were 2 PAK Numbers) and after I entered both of those the SKUs that came up were: L-LIC-CT2504-UPG and L-LIC-CT2504-1A.
So I chose to download the License files and when I did I received a ZIP file containing one html file with instructions and one .lic file containing the License.
Here is what I see when I try:
        (Cisco Controller) > license install tftp://192.168.x.xxx/Cisco_WLC2504_Licenses/license_file_name.lic
        Transfering licenses from tftp://192.168.x.xxx/Cisco_WLC2504_Licenses/license_file_name.lic
        License installation: No valid license found to be installed
Anyone know why I would be receiving this error? I tried uploading to the WLC from both the Web Interface and the CLI with the same result.
I also tried having them email me the .lic file instead but I get the same thing when I try to upload it.
Any ideas?
Thanks,
Matt

Hey Vinod, thanks for the reply!
We had received an Access Point from our Cisco VAR partner and also ordered the License so we could add a 6th AP to the WLC. When we received the AP in the Mail the License was not with it so we emailed our acct rep and asked him for it, which is when they had me run the "show udi" command in order to give them the Serial Number so they could get me the PAK number. Which is I assume what you were talking about with the UDI (Unique Device Identifier)?
The License file itself contains the correct serial number, which is why I'm confused as to why it's not working. We don't have a SmartNet for this device so one of our Techs through our Cisco Var partner is contacting their Cisco Account Rep to find out what's going on. I guess I'll just wait till I hear back from them, and we'll see what they say. I even tried doing the Get Existing option on Cisco.com for the Product License Registration section of the site, which also did not work.
The strange thing is, when I did the Get Existing option and I downloaded the License file again, the Filename was different then it was the first time around... Not sure if this is normal or not, but I just thought that was strange.
Thanks Again for the reply Vinod..!
Thanks,
Matt

CISCO Box not working with Infrared Remove Control Repeater

There was an Infrared Remote Control Repeater set-up in my newly purchased house. It works for my LG DVD player, but does not work with my CISCO CHS435HDB box. Are there any work around for this? Should I change to a different box?

If you are using a repeater, make sure the piece that is relaying the IR signal is pointing directly the font of the Cisco box and nothing is plugged into the IR input port in the back of the box.
Anthony_VZ
**If someones post has helped you, please acknowledge their assistance by clicking the red thumbs up button to give them Kudos. If you are the original poster and any response gave you your answer, please mark the post that had the answer as the solution**
Notice: Content posted by Verizon employees is meant to be informational and does not supersede or change the Verizon Forums User Guidelines or Terms or Service, or your Customer Agreement Terms and Conditions or plan

Setting the custom master page through powershell is NOT working

Hi,
I am writing the below code to set the custom master page through powershell.
But its not working .when i went to site settings-->master page --> in the drodown , the maste page set is seattle.master ONLY, though my current master page is available in the dropdown.
Can anyone pls help, whether i am missing in the below :
      Add-PSSnapin Microsoft.SharePoint.Powershell
       $SiteURL = "http://srvr1:22307/sites/SPW5"
    $weburl= $SiteURL
    $Site= Get-SPSite $SiteURL
    $web = $Site.OpenWeb()
$web.CustomMasterUrl = "/_catalogs/masterpage/myMasterpage.master"
$web.MasterUrl = "/_catalogs/masterpage/myMasterpage.master"
$web.Update()
Das

Hi,
Is it a publishing page? If yes can you try the PowerShell scripts corresponding to the following code snippet?
var publishingWeb = PublishingWeb.GetPublishingWeb(web);
publishingWeb.CustomMasterUrl.SetInherit(inheritFromParent, false);
publishingWeb.CustomMasterUrl.SetValue(masterPageUrl, false);
publishingWeb.MasterUrl.SetInherit(inheritFromParent, false);
publishingWeb.MasterUrl.SetValue(masterPageUrl, false);
I've noticed sometime (not sure though) that Master page doesn't get updated if the inherit property is not updated first.
Thanks,
Sohel Rana
http://ranaictiu-technicalblog.blogspot.com

Loading flash through ajax does not work in IE 6.

Hi all,
I am having some problems on a site I'm developing. When I
load a video from youtube, etc, and do so dynamically through ajax,
it does not work on IE 6. Mind you it does work on all other
browsers. This problem happens with multiple copies of IE 6 so it
is reproducible. Not sure if there are any web devs here but any
help would be greatly appreciated.

Well, this probably belongs over in the Flash forum. That's
where the developer questions go.. It's surely a matter of the way
the code is written (or possibly the paths to the different
components. There are security restrictions on certain types of
loading that may also come into play. Hard to tell without more
detail.

Sound Output through external speakers not working

For some reason, the sound output to my JBL speaker system that is connected through the headphones jack of my iMac has cut out. When I go to the Sound Preferance panel, under Output, my choices are :
Internal Speakers
Soundflower (2CH)
Soundflower (16CH)
I have NO idea what these Soundflower things are, and don't see a standard "Headphones" option, which is the jack they are plugged into. I also don't see a way to delete these Soundflower "devices".
The sound output not working seemed to happen after a power outage in my building, so I'm going to try a powerreset of the iMac, but still not sure what is going on with this Soundflower stuff.

/System/Library/Extensions/Soundflower.kext and restarting your computer uninstalls Soundflower.
To remove preference panes, context-click on the preference pane's icon and select the Remove option.
https://getsatisfaction.com/cycling74/topics/how_to_uninstall
Long shot, but...
Open Audio Midi Setup in Applications>Utilities, see the input & output options & KHz setting there, some things will change it for their own use, then not set it back.

Smartview v11.1.1.3 drill through reports does not work in grids?

Hi,
I'm using v11.1.1.3 and know there is a drill through function to FDM from Smartview grids. I've tried but it does not work in the grids, only works in the forms. However, I'm able to drill through to FDM from workspace grids. Does anyone encounters the same?? Appreciate any kinds advices. Thanks!

Are you certian that the report is showing an input level cell? Often reports are designed to run at Total dimension members, i.e. <Entity Curr Total> which you can not drill into.

Videoconference through wireless card not working 100% but ethernet is fine

my system is:
Macbook Pro, running 10.5.1 and I have an Airport Extreme 802.11g running on bridge mode.
When I use iChat 4.0 and video chat with a fellow with a similar setup, I have no issues if I connect through the ethernet port of the Airport Extreme base station with the laptop's airport card off, but I cannot start it up through the wireless. The even more curious thing is that if I happen to turn the airport card back on, and then wait for it to set up, then disconnect the ethernet cable, I can then start a video chat through the wireless.
I have tried changing the port on my iChat configs in Server settings to 443, and that did not work. My only guess is that there is a port issue of some kind. I have made sure that under System Preferences that I have allowed all connections (while testing this) and STILL it will not work.
Any ideas?
Message was edited by: ulcain

Having read many of the posts since Leopard came out regarding the Airport Base Station - I would have to concede that there is something odd about the combination of iChat, the Mac Firewall and a Base Station.
Now there was a problem with the Mac Firewall at the base 10.5 release and the 10.5.1 basically turned it On.
Now, for the Base station there does seem that there is almost some interaction between the firewall and the Base Station.
It appears that if Allow Specifics was set before the 10.5.1 update was done that the firewall my not be fully recognising this.
The suggestion is to remove all apps from the Allow Specifics list and set the Firewall back to the default Allow All.
Then it can be reset to Allow Specifics and iChat Re-added to the list.
8:00 PM Sunday; January 27, 2008

Interconnection between HP and Cisco is not working

Dear all,
I support some old colleagues by connecting a Cisco 2960x with an HP Switch. Both sides are UP/UP, stp is fine, channel also. The Cisco switch is also fine. But not data traffic is working.
I see that we are sending but not receicing any packet. the same on the other side. We checked the cabeling use different fibers, etc. everything is fine. when we connect a copper port, its also fine. Online on the LWL side we have this problem. But interface and line protocol is UP.
Is there any command I may not know to check the LWL. UDLD is not working because we have just on cisco on one end. test tdr works only on copper. I guess there is something wrong with the compatibility between the both Gbics, but i can't exaclty say what it is. We use monomode and LX Gbic.
On another Core Switch HP/Cisco is working finde with SX.
I don't have live access, so sorry for any delay in my answer.
regards,
Sebastian

Hi cbafiero,
It seems that the problem lies in your router. I'm not sure exactly what the issue is (I've just now discovered it myself), but after switching from a Linksys WRT54GX2 to a thrift store Netgear, my shared libraries appeared instantly. My gut is telling me that the Linksys routers are blocking the multicast traffic, which is stupid on Linksys's part, to filter traffic internally. I'll look more into the Netgear and see what it has that the Linksys doesn't (or vice versa).

DTS (5.1) Audio Through Airport Express: Not Working

I imported some DTS-encoded WAV files into iTunes, to stream to my audio system via an Airport Express. The AE is connected to the preamp via optical, the WAV files were not converted or modified in any way, and the volume is @ 100% in iTunes.
The preamp receives the files and the DTS icon lights up, so all seems to be good... except the audio output is 2.0 only. As a test I converted the files to Apple Lossless (since I know the AE has to make that conversion), same result.
As another test I turned down the volume in iTunes and the audio became white noise, another indication that the files are DTS.
If I burn an audio CD using iTunes and the same WAV files, and play them on my OPPO player I get 5.1, the final and conclusive proof that the files are properly encoded.
I know I've read that streaming DTS-encoded audio via the Airport Express is possible, so I'm not sure what I might be doing wrong.
Any ideas?

Hi,
I experienced some DTS files in iTunes, with my AirPort Express some months ago, it was working fine on my Marantz receiver. A few days ago I wanted to listen to them again, only white noise... I wanted to rip by myself a DTS-CD, therefore I found this out. Apparently since AirTunes has been turned to AirPlay, it's not working anymore (?) / the same way.

Impersonation through C# is not working - sending wrong CallingID

Hello,
I need to modify the UserQuery entity, but per securities I can't update this unless it's updated as each individual user. So I've written a piece to update it using Impersonation by setting the CallerID. Below is a snippet of the code:
using (OrganizationServiceProxy proxy = new OrganizationServiceProxy(SvcMgt, Creds))
Guid OwnerID = new Guid("0c5b54bb-f2ab-e411-94aa-005056843a89");
proxy.CallerId = OwnerID;
Guid UserQueryId = new Guid((row["UserQueryId"].ToString()));
ColumnSet attributes = new ColumnSet(new string[] { "fetchxml"});
Entity userquery = new Entity("userquery");
userquery = proxy.Retrieve(userquery.LogicalName, UserQueryId, attributes);
userquery["fetchxml"] = row["FixedFetchXML"].ToString();
proxy.Update(userquery);
When I run this I get the error below:
System.ServiceModel.FaultException`1[Microsoft.Xrm.Sdk.OrganizationServiceFault]:
SecLib::AccessCheckEx failed. Returned hr = -2147187962,
ObjectID: 428e02bb-acb3-e411-94aa-005056843a89,
OwnerId: 0c5b54bb-f2ab-e411-94aa-005056843a89,
OwnerIdType: 8 and
CallingUser: e0d62cbb-86d6-e411-94aa-005056843a89.
ObjectTypeCode: 4230,
objectBusinessUnitId: 45072abb-5187-e211-86aa-005056b07049,
AccessRights: Read
Access (Fault Detail is equal to Microsoft.Xrm.Sdk.OrganizationServiceFault).
The CallingUser is me, but I assumed this would be the user I'm trying to impersonate given I've set that GUID as the CallerID. What am I missing?
Thanks in advance for any suggestions.

Thanks for the options. What I'm seeing now is my Impersonation code is working when I set the CallerId, but it's not working congruently across all users. For example I have two users, and I can run the following for one user and it creates
the Contact under that user, but if I change the CallerId to another User's GUID it creates the Contact under me and not that second user:
using (OrganizationServiceProxy proxy = new OrganizationServiceProxy(SvcMgt, Creds))
proxy.CallerId = new Guid("BBC683AA-3E8B-E211-98BB-005056B07049");
Guid NewContact;
Entity contact = new Entity("contact");
contact["firstname"] = "Test2";
contact["lastname"] = "Test2";
NewContact = proxy.Create(contact);
System.Console.WriteLine(NewContact.ToString());
At this point I believe my code is valid and working, because under the user that it works on the correct user is setup as the ModifyBy, CreateBy, etc but I'm setup as the ModifiedOnBehalfBy and CreatedOnBehalfBy. And I've even tested this with
updating the User Query entity, for some I can modify their Query successfully but for the same ones that won't allow me to setup a new Contact for them I can't update the User Query entity as them either.
So my question now is why does Impersonation work on some users but not on others. I've compared the profiles of users that it does and doesn't work on, but I can't find any difference.
Thanks --

LELA icon has red cirle with line through it. Not working.

On one of my home computers, my Linksys icon in the sytem tray has a red circle with a line thorugh it. It doesn't seem to be working. Tried rebooting, repairing the install, rebooting, uninstalling, rebooting, reinstalling, rebooting, OK I'm all out of reboots. It still doesn't work.
LELA works OK on two other computers. (All 3 are Vista computers.)

Gerco, LELA does not work no matter what version. If it does, consider yourself lucky. If not, don't waste your time. It gives incorrect information and makes any troubleshooting of the network difficult from normal procedures due to its interference. Please remove it from your system as it is not needed for ANYTHING for the router or your network, sorry. The program that might work better is Network Magic, try that.

Cisco 877 - not working with apple devices

Hello all,
I'm hoping someone can help me with a problem I have with my 877 adsl router.
A bit of background:
I have set this up as my home router to the internet, which is connected to a Linksys WRT54GL as a wireless access point.
My windows & Linux devices/laptops all work fine over this setup and connect without a problem
However, all my apple devices, phones and ipads don't fully work. I can get to google and a handful of pages, but not the store or games or facebook etc. (my daughter thinks its the end of the world - without FB and instagram)
If I take out the Cisco and put a Thompson router in, it all works fine. so I'm assuming it something with the Cisco config.
Below is the config I'm using on the router
Any pointers would be most appreciated.
ddhrouter#sh run
Building configuration...
Current configuration : 2292 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname ddhrouter
boot-start-marker
boot-end-marker
enable secret 5 mysecret
no aaa new-model
dot11 syslog
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.1.1
ip dhcp pool CISCODHCP
   network 192.168.1.0 255.255.255.0
   dns-server 212.50.160.100 213.249.130.100 8.8.8.8
   default-router 192.168.1.1
ip name-server 212.50.160.100
ip name-server 213.249.130.100
ip name-server 8.8.8.8
username cisco privilege 15 password 0 mysecret
archive
log config
hidekeys
interface ATM0
description ** adsl interface **
mtu 1452
no ip address
load-interval 30
no atm ilmi-keepalive
pvc 1/50
ubr 288
encapsulation aal5mux ppp dialer
dialer pool-member 1
dsl operating-mode auto
hold-queue 224 in
interface FastEthernet0
interface FastEthernet1
interface FastEthernet2
interface FastEthernet3
interface Vlan1
description ** local lan **
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
hold-queue 100 out
interface Dialer0
no ip address
interface Dialer10
description ** adsl dialer interface **
ip address negotiated
ip mtu 1482
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
ppp chap hostname myusername
ppp chap password 0 mypassword
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer10
no ip http server
no ip http secure-server
ip http max-connections 4
ip http timeout-policy idle 600 life 86400 requests 10000
ip nat inside source list 1 interface Dialer10 overload
ip access-list extended TerminalAccess
permit tcp host 192.168.1.0 any eq telnet
permit tcp any any eq 22
deny   tcp any any
ip access-list extended no_telnet
deny   tcp any any eq telnet
access-list 1 remark INSIDE_IF=Ethernet0
access-list 1 remark SDM_ACL Category=2
access-list 1 permit 192.0.0.0 0.255.255.255
access-list 110 permit icmp any any echo
access-list 110 permit icmp any any echo-reply
dialer-list 1 protocol ip permit
control-plane
line con 0
password password
no modem enable
line aux 0
line vty 0 4
access-class TerminalAccess in
password password
login
scheduler max-task-time 5000
end
ddhrouter#
all I'm after is a standard setup for my router. allow any out - deny any in.
Many thanks in advance.
Dave

ooo, you left your username, password, and enable in in clear text in the config you pasted, as well as not having an outside ACL applied and the VTY ACL allowing ssh from anywhere. Luckily the outside IP address isn't in the config or I'm sure someone would get ahold of your router....:) You should apply an outside access list and a firewall (I prefer CBAC firewall config for ease of use, but there is Zone based) to fix this. I assume ACL 110 was meant to be your outside ACL but it just isn't applied.
That being said Jody is likely right. PPPoE requires you to shrink your packet size (MTU/MSS) to allow room for the encapsulation that gets added to the packet. The command he supplied should fix this.
The 'ip mtu 1482' on the dialer interface may be too large as well.

WakeOnLan (WOL ) through Cisco 870 not working

Similar Messages

Maybe you are looking for