Was not able to stop the listener

Hi All,
As a part of shut down I stopped the application tier and Database and Then when I was trying to stop Listener I was getting the below error.
LSNRCTL> show log_file
Connecting to (ADDRESS=(PROTOCOL=tcp)(HOST=)(PORT=1521))
TNS-12541: TNS:no listener
TNS-12560: TNS:protocol adapter error
TNS-00511: No listener
Linux Error: 111: Connection refused
I couldn't find where I was going wrong.. Can anyone help me out in this.

Hi Helios,
Here is the output of the listener status
[oracle@oracleerp PROD_oracleerp]$ ps -ef|grep inherit
oracle 4831 4080 0 11:19 pts/1 00:00:00 grep inherit
And these are the entries in /etc/hosts file
[oracle@oracleerp PROD_oracleerp]$ cat /etc/hosts
# Do not remove the following line, or various programs
# that require network functionality will fail.
192.168.0.113 oracleerp.localdomain.com oracleerp
127.0.0.1 localhost.localdomain localhost
And Service Network Restart -- I already tried
[oracle@oracleerp PROD_oracleerp]$ service network restart
Shutting down loopback interface: Users cannot control this device.
[FAILED]
rm: cannot remove `/var/lock/subsys/network': Permission denied
Setting network parameters: error: permission denied on key 'net.ipv4.ip_forward'
error: permission denied on key 'net.ipv4.conf.default.rp_filter'
error: permission denied on key 'net.ipv4.conf.default.accept_source_route'
error: permission denied on key 'kernel.sysrq'
error: permission denied on key 'kernel.core_uses_pid'
error: permission denied on key 'kernel.shmall'
error: permission denied on key 'kernel.shmmax'
error: permission denied on key 'kernel.shmmni'
error: permission denied on key 'kernel.sem'
error: permission denied on key 'fs.file-max'
error: permission denied on key 'net.ipv4.ip_local_port_range'
error: permission denied on key 'net.core.rmem_default'
error: permission denied on key 'net.core.wmem_default'
error: permission denied on key 'net.core.rmem_max'
error: permission denied on key 'net.core.wmem_max'
[FAILED]
Bringing up loopback interface: Users cannot control this device.
[FAILED]
Bringing up interface eth0: Users cannot control this device.
[FAILED]
touch: cannot touch `/var/lock/subsys/network': Permission denied
But Didnt yet
I had gone through the document you suggesed already.
Please suggest me how i can get this issue fixed.

Similar Messages

Not able to start the listener in oracle 10g after the domain name changed

Hi
I had installed the oracle 10g on zLinux. It was working fine( was able to mount the database and start the listener). Now my server's domain name got changed. So i have added the new domain name in the tnsnames.ora and listeners.ora file . now i could able to mount the databases but am not able to start the listener . whille starting the listener , am getting the following error
oracle@ptcr4d00:~> lsnrctl start
LSNRCTL for Linux: Version 10.2.0.2.0 - Production on 05-AUG-2009 10:31:05
Copyright (c) 1991, 2005, Oracle. All rights reserved.
Starting /opt/oracle/10g/bin/tnslsnr: please wait...
TNSLSNR for Linux: Version 10.2.0.2.0 - Production
System parameter file is /opt/oracle/10g/network/admin/listener.ora
Log messages written to /opt/oracle/10g/network/log/listener.log
Listening on: (DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(KEY=EXTPROC1)))
Listening on: (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=PTCR4D00)(PORT=1521)))
Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=IPC)(KEY=EXTPROC1)))
TNS-12547: TNS:lost contact
TNS-12560: TNS:protocol adapter error
TNS-00517: Lost contact
Linux Error: 104: Connection reset by peer
Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=PTCR4D00)(PORT=1521)))
TNS-12541: TNS:no listener
TNS-12560: TNS:protocol adapter error
TNS-00511: No listener
Linux Error: 111: Connection refused
I have posted the contents of the tnsnames.ora and listeners.ora
TNSNAMES.ORA
TC =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = PTCR4D00)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = TC)
EXTPROC_CONNECTION_DATA =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1))
(CONNECT_DATA =
(SID = PLSExtProc)
(PRESENTATION = RO)
LISTENERS.ORA
SID_LIST_LISTENER =
(SID_LIST =
(SID_DESC =
(SID_NAME = PLSExtProc)
(ORACLE_HOME = /opt/oracle/10g)
(PROGRAM = extproc)
LISTENER =
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1))
(ADDRESS = (PROTOCOL = TCP)(HOST = PTCR4D00)(PORT = 1521))
Could you please help me to resolve this issue ?
Regards
Mani

Hi
Please find the content of the /etc/hosts below
# IP-Address Full-Qualified-Hostname Short-Hostname
#127.0.0.1 localhost
9.124.114.49 PTCR4D00
# special IPv6 addresses
::1 localhost ipv6-localhost ipv6-loopback
fe00::0 ipv6-localnet
ff00::0 ipv6-mcastprefix
ff02::1 ipv6-allnodes
ff02::2 ipv6-allrouters
ff02::3 ipv6-allhosts
9.124.114.49 PTCR4D00 PTCR4D00
Regards
Mani

Hi I was using whatsapp on my iPhone5.I was not able go to the main menu by pressing the center button so I hold on to the button for 2 seconds.Then the whole display turned out to be black

I was not able go to the main menu from whatsapp by pressing the center button so I hold on to the button for 2 seconds.Then the whole display turned out to be black & white. how can i fix it?

Hello monicaa003,
Thanks for participating in the Apple Support Communities.
If your iPhone display turned black and white after holding down the Home button for 2 seconds, first try pressing the Home button again to go to the main menu (Home screen.)
For reference, holding down the Home button for 2 seconds will trigger Siri if that feature is enabled:
About Siri - Apple Support
If pressing the Home button doesn't return you to the main menu, try restarting or resetting your iPhone:
Restart or reset your iPhone, iPad, or iPod touch - Apple Support
Additionally, if Whatsapp is not responding or working as expected, see the troubleshooting steps at this link:
If an app you installed unexpectedly quits, stops responding, or won’t open - Apple Support
Best Regards,
Jeremy

HT202873 I just purchased GB10 last week and I repeatedly keep getting the following message, "Garageband was not able to install the new sounds. Close and re-open Garageband to download and install them again." I have tried EVERY suggestion!

Model Name: MacBook Pro
OS X Yosemite: 10.10.2
Model Identifier: MacBookPro8,2
Processor Name: Intel Core i7
Processor Speed: 2.3 GHz
Number of Processors: 1
Total Number of Cores: 4
L2 Cache (per Core): 256 KB
L3 Cache: 8 MB
Memory: 4 GB
I just purchased GarageBand 10.0.3 last week and I repeatedly keep getting the following message when I try to download ANY of the FREE Piano lessons in the "Lesson Store", "Garageband was not able to install the new sounds. Close and re-open Garageband to download and install them again." I have tried EVERY suggestion that I have come across on the internet and nothing is working! If I'd known I would encounter this issue, I would not have paid for this. Tried restarting, rebooting, reinstalling, deleting the cache, and on the verge of just reinstalling the OS. I have come across people have the same issue for months and I can't believe Apple has not offered a fix or update or anything.

Immargarita, Since you just purchased the software you qualify for a no charge one on one at an Apple store. They never could tell me what was wrong, but after three visits and not one dime, all lessons downloaded at the store. I was not going home until it worked.
Hint, hint, I had just upgraded OX when the problem started. So... I qualified for tech support. I forgot to get my none working since the up grade Photoshop fixed. Some Java component can't be found and just like GB, the link to Apple for support does not work. I have the good old PS disc. I'm not happy with this cloud stuff.
When you call and give the SN for your computer, they may say it will cost $29.00 dollars for one time support. Instead choose a different prompt, tell the human being what your problem is and set up a visit to the Apple store. BTW, no one at the store seemed to have heard of this issue.
The techie just started the download and ran the activity monitor. The download stopped once. Then he continued it and everything is there now.
Shame on you Apple.
Hope this helps.

Garageband was not able to install the new sounds

I'm on an iMac 21.5-inch (mid 2011) running Yosemite; 2.5 GHz Intel Core i5; 4GB memory.
A few months ago, I uninstalled GarageBand. Now I'm trying to reinstall it. I can get GarageBand 6 reinstalled, but I would like to get working with the latest version. I'm able to download the latest version from the App Store with no issue. It installs with no issue.
When I open it, it thanks for me downloading it, and then begins to download "an essential collection of sounds and loops." After a bit of downloading, it asks for my admin password; I enter it, and a few seconds later, it gives the error: "GarageBand was not able to install the new sounds. Close and re-open GarageBand to download and install them again." Closing and reopening GarageBand just takes me through the same loop (no pun intended). When the window is open, if I click on the GarageBand menu in the Apple bar, nothing happens.
It does not ask me to accept anything; I am signed into the App Store with the same Apple ID I have always used (it is the only one I have ever had, so that's not the issue). I am an admin on my Mac, so it's not a permissions issue. It's not a password issue either.
Things I have tried:
Rebooting into Safe Boot and opening from there; same issue.
Repaired permissions (it fixed oodles of things completely unrelated to GarageBand); same issue.
Creating a new admin profile and opening from there; it gives a different error, but the effect is the same.
Removed the program, trashed anything remotely related to GarageBand (preferences, folders, etc), emptied the trash, restarted the computer, reinstalled; same issue.
Installed GarageBand on top of itself, just in case; same issue.
I can't think of what else to try. Help!
For reference, here is a screenshot of what I'm getting stuck on:

The solution Lijoesat posted above worked for me!
First I found the private/var/folders/ (and then lots of gibberish folders) and singled out two garageband files and deleted them. This did not work.
I then deleted everything which may or may not be a good thing, I am an idiot, I have no idea if these are extremely important files or not!
I tried to empty the trash bin after but many files was locked and Garageband would still not install.
I did a restart of the computer, emptied the bin successfully and tried to install Garageband again and it worked fine!
The inserted picture show some of the folder structure, I deleted everything after private/var/folders/

Cannot get all the sounds in library to download. I get this message GarageBand was not able to install the new sounds. Close and re-open GarageBand to download and install them again.

When I attempt to download all the sounds in my Garage Band library, I get this message.
"GarageBand was not able to install the new sounds. Close and re-open GarageBand to download and install them again". When I do this, I get the same message again.
CAn anyone advise how to get all the sounds in my Garageband library?

the same here for the drummers sounds in garageband 10xxx

HT5252 I tried to change my metadata date and got this Aperture was not able to adjust the date and time of the original file "01769_p_h13ajyrm4bm0944.jpg" because it is locked or you do not have permission to modify it.

I tried to change the metadata date. It changed the date on my photo, but when I checked the box that said "also change my original file", it gave me this error message.
Unable to change original file. Aperture was not able to adjust the date and time of the original file “01769_p_h13ajyrm4bm0944.jpg” because it is locked or you do not have permission to modify it.
Wassup?

What is your Aperture version? The older versions of Aperture 3 had a problem to apply Metadata changes to the original file.
If you are using the current version Aperture 3.4.5, try to repair the permissions on your Aperture library, if you have not already done so:
Launch Aperture with the key combination ⌥⌘ held down and select "Repair Permissions" from the First Aid PAnel, that will appear.
If that does not help, post back with more information on your original files - are the referenced or managed? Where is your Aperture library located? Since when do you have this problem? And what did you do directly before noticed the problem for the first time?
Regards
Léonie

Aperture was not able to adjust the date and time of the master file "2008-06-22 at 14-41-14.jpg" because it has a format that does not permit date modification.

I can't seem to find a way to update the date/time of a master file. There is a format issue but I can't seem to figure out how to correct it.
Aperture was not able to adjust the date and time of the master file “2008-06-22 at 14-41-14.jpg” because it has a format that does not permit date modification.

Can you post an ipconfig /all from the server and the DC?
Robert Pearman SBS MVP
itauthority.co.uk |
Title(Required)
Facebook |
Twitter |
Linked in |
Google+

Initially I had downloaded Document 2 (Free) application to view my doc, ppt and xls files. I was not able to edit the files so there was an option for upgrade the Document-2 free to paid version. I have upgraded the Document 2 application.

Initially I had downloaded Document 2 (Free) application to view my doc, ppt and xls files. I was not able to edit the files so there was an option for upgrade the Document-2 free to paid version. I have upgraded the Document 2 application. But on my iPad now there are to application present Docemnt-2 (Free) and Document-2. I am not able to open any existing document using the upgraded version of application. How do I connect all the existing txt,PPT,XLS doccument to the new upgraded Document-2 application and then to edit it on my iPad.

As suggested I had deleted the free application and did a hard restart the iPad. I have again copied the document using iTunes. But I am not able to edit any document using this app. Document 2 (paid version) supports editing features of the txt/ xls /ppt files. Is there any problem while loading the Document 2 app. If I reload then do I need to purchase again?

I exported a pages document to word, but was not able to edit the new word document.

i exported a pages document to word, but was not able to edit the new word document.

I have a OSX IMAC Version 10.8.5. I got pages at the same time I purchased this computer. I use a document to write all my passwords. Seems like when I E-mail myself the document from pages, I have not been able to type in the document, it acts like it is locked. I checked all the "lock" and "unlock" fields, and none of them were locked. I notice the document says PDF. How do I correct this? Seems like I've tried everything. If you can help, that would be great!

NOt able to start the listener..

After Indtalling oracle 11g .. i am not able to start the listener
dbstart $ORACLE_HOME
lsnrctl start
ORACLE_SID=orcl
export ORACLE_SID
lsnrctl start
[oracle@test1 bin]$ lsnrctl start
LSNRCTL for Linux: Version 11.1.0.6.0 - Production on 27-DEC-2012 15:35:36
Copyright (c) 1991, 2007, Oracle. All rights reserved.
Starting /u01/app/oracle/product/11.1.0/db_1/bin/tnslsnr: please wait...
TNSLSNR for Linux: Version 11.1.0.6.0 - Production
System parameter file is /u01/app/oracle/product/11.1.0/db_1/network/admin/listener.ora
Log messages written to /u01/app/oracle/diag/tnslsnr/test1/listener/alert/log.xml
Listening on: (DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(KEY=EXTPROC1521)))
Listening on: (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=test1.com)(PORT=1521)))
Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=IPC)(KEY=EXTPROC1521)))
STATUS of the LISTENER
Alias LISTENER
Version TNSLSNR for Linux: Version 11.1.0.6.0 - Production
Start Date 27-DEC-2012 15:35:37
Uptime 0 days 0 hr. 0 min. 0 sec
Trace Level off
Security ON: Local OS Authentication
SNMP OFF
Listener Parameter File /u01/app/oracle/product/11.1.0/db_1/network/admin/listener.ora
Listener Log File /u01/app/oracle/diag/tnslsnr/test1/listener/alert/log.xml
Listening Endpoints Summary...
(DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(KEY=EXTPROC1521)))
(DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=test1.com)(PORT=1521)))
**The listener supports no services**The command completed successfully
tried all posibalaties as here
Oracle 11g Listener Supports No services
Please help me beacuse of which my work is struck for whole day

[oracle@test1 bin]$ ps -ef|grep tns
oracle 13498 11176 0 16:41 pts/5 00:00:00 grep tns
[oracle@test1 bin]$
[oracle@test1 bin]$ lsnrctl start
LSNRCTL for Linux: Version 11.1.0.6.0 - Production on 27-DEC-2012 16:41:08
Copyright (c) 1991, 2007, Oracle. All rights reserved.
Starting /u01/app/oracle/product/11.1.0/db_1/bin/tnslsnr: please wait...
TNSLSNR for Linux: Version 11.1.0.6.0 - Production
System parameter file is /u01/app/oracle/product/11.1.0/db_1/network/admin/listener.ora
Log messages written to /u01/app/oracle/diag/tnslsnr/test1/listener/alert/log.xml
Listening on: (DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(KEY=EXTPROC1521)))
Listening on: (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=test1.com)(PORT=1521)))
Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=IPC)(KEY=EXTPROC1521)))
STATUS of the LISTENER
Alias LISTENER
Version TNSLSNR for Linux: Version 11.1.0.6.0 - Production
Start Date 27-DEC-2012 16:41:10
Uptime 0 days 0 hr. 0 min. 0 sec
Trace Level off
Security ON: Local OS Authentication
SNMP OFF
Listener Parameter File /u01/app/oracle/product/11.1.0/db_1/network/admin/listener.ora
Listener Log File /u01/app/oracle/diag/tnslsnr/test1/listener/alert/log.xml
Listening Endpoints Summary...
(DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(KEY=EXTPROC1521)))
(DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=test1.com)(PORT=1521)))
The listener supports no services+The command completed successfully
[oracle@test1 bin]$
[oracle@test1 bin]$ echo $ORACLE_SID
orcl
[oracle@test1 bin]$ echo $ORACLE_HOME
/u01/app/oracle/product/11.1.0/db_1
[oracle@test1 bin]$
[oracle@test1 bin]$

TS4513 I KEEP GETTING THIS ERROR. PLEASE HELPMainStage 3 was not able to complete the download. Check your internet connection and try downloading again.

I KEEP GETTING THIS ERROR. PLEASE HELPMainStage 3 was not able to complete the download. Check your internet connection and try downloading again.

Hi
From others (on the Logic Forums), it seems that there may have been issues with Apple's servers.
Try again...
if that does not work, delete Mainstage, and then try again to download teh whole thing.
Alternatively, the direct link to the basic content is here:
https://discussions.apple.com/thread/6015391?tstart=0
CCT

Just purchased a new mac mini 3GHz Intel Core i7, with 16GB ram version 10.10.1. With it i purchased a new wireless keyboard. All of a sudden I was not able to use the #1 key. I thought I had a defected newly purchased keyboard. I pulled out my older

Just purchased a new mac mini 3GHz Intel Core i7, with 16GB ram version 10.10.1. With it i purchased a new wireless keyboard. All of a sudden I was not able to use the #1 key. I thought I had a defected newly purchased keyboard. I pulled out my older wireless keyboard, and the same thing happened. It must not be the keyboard if it happened to two different keyboards. I have a habit of restarting my computer, when things don't work, I find it helps, and sure enough, everything works. Today, it happened again. Does anyone know what is causing this to happen?

Try resetting the SMC and PRAM
Intel-based Macs: Resetting the System Management Controller (SMC)
About NVRAM and PRAM
Try reinstalling Yosemite with out losing stuff. See:
OS X Yosemite: Reinstall OS X

10/4-2014 - "GarageBand was not able to complete the download. Check your internet connection and try downloading again." Ver. 10.0.2.

I have downloaded GarageBand and when I first clicked to open it started dowloading a content package. But then in the middle of this it told me that my perfectly fast working internet connection was not availeble. See attached screenshot.
Does anybody know how to solve this?
I have tried deleting and downloading againg but same message appears.
Best,

GarageBand was not able to complete the download. Check your internet connection and try downloading again.
Todavía no puedo instalarlo, lo he descargado y eliminado por mas de 5 veces.
Por favor alguna solución a esta situación?

Help needed: "Logic was not able to complete the download"

I purchased Logic Pro 9 today from App store. Downloaded and installed the software. After installation & startup Logic started to download 2GB of additional content. This download was interrupted by the message "logic was not able to complete the download". I trashed Logic, redownloaded and reinstalled it several times from App store, always gives same message after startup. Doesn't even start to download basic content again, just gives the message. After hitting "ok" Logic just quits. This is extremely frustrating and I have no idea what to do about this.
I would very much appreciate any advice about how to solve this problem!

I start with the same problem but it ends differently.
I purchased Logic Pro 9 today from App store. Downloaded and installed the software. After installation & startup Logic started to download
the basic content. Upon startup the program already seemed weird, but it started and finished the basic content.
By weird I mean all I get on my screen is the Logic menu bar and the text is yellow instead of black. To top it all up, the text from the menus is missing and all I get is empty boxes.
I have deleted it and reinstalled from the app store to ensure a new clean installation but still the problem persists.
I have checked all your above points as well and none seem to work would be grateful for any help.
Cheers

Was not able to stop the listener

Similar Messages

Maybe you are looking for