What are the settings to remain only in the 5MHz mode?

I would like to remain only in the 5MHz mode ond skipp the 2.4 MHz ode in my wireless net: What ate te setting 802.11 a/n - 802.11 b/g/n ans what do tey mean?
Hans

The Time Capsule and AirPort Extreme are simultaneous dual band wireless routers. This means that they broadcast both a 2.4 GHz and 5 GHz signal at the same time.
It is not possible to turn off one band and leave the other active. Either both bands are "on", or both bands are "off".
The setting of 802.11a/n --- 802.11 b/g/n is the default setting for the Time Capsule and AirPort Extreme.
802.11a/n are 5 GHz wireless modes. The other side of the ---- (dash) 802.11 b/g/n are 2.4 GHz modes.
Note that "n" wireless can operate at both 2.4 GHz and 5 GHz settings.
By default, both the 2.4 GHz and 5 GHz bands use the same wireless network name.
It is possible using Wireless Options in AirPort Utility to assign a separate name to the 5 GHz band if you wish, but this will not turn off 2.4 GHz.

Similar Messages

HT201210 I was in the middle of installing the new update using the wifi at a local restaurant when I lost the wifi signal and my iPhone shut down, and now I can't get into the phone. I only get the iTunes logo with the cable pic. What are my options now?

I was in the middle of installing the new update using the wifi at a local restaurant when I lost the wifi signal and my iPhone shut down, and now I can't get into the phone. I only get the iTunes logo with the cable pic. What are my options now?

Your only option is to connect your iPhone to your computer via USB (as the diagram indicates) and restore using iTunes.

What are these settings about?

In the editor workspace immediately below the photo you are working, on is a drop down tap which can display documents profile,documents dimensions,sizes, scratch sizes, timing etc. What are these settings all about I didn't see them mentioned in the manual? And then over to the left a area where it shows percentage. Percentage of what?
I'm using PSE5

This information is present in the help files.
Just open the help for PSE 5, and type the word 'status' in 'Search for' input for the product.
This will lead you to 'To display file information in the Info palette or status bar' page. It contains the answer to your query.
The percentage is to specify the Zoom percentage of your image.

Hello. I have this situation: iphone 5s freezes and does not respond. connect to itunes to restore it, but there says that I should turn off search by icloud in the settings of cellphone. but if the phone freezes?? what to do?? help me please!!

Hi. I have this situation: iphone 5s freezes and does not respond. connect to itunes to restore it, but there says that I should turn off search by icloud in the settings of cellphone. but if the phone freezes?? what to do?? help me please!! Thanks advanced!!

Check for hardware issues
Related errors: 1, 3, 10, 11, 12, 13, 14, 16, 20, 21, 23, 26, 27, 28, 29, 34, 35, 36, 37, 40, 1000, 1002, 1004, 1011, 1012, 1014, 1667, or 1669.
These errors mean that your device or computer may have a hardware issue that's preventing the update or restore from completing.
Check that your security software and settings aren't preventing your device from communicating with the Apple update server.
Then try to restore your iOS device two more times while connected with a cable, computer, and network you know are good.
Confirm that your security software and settings are allowing communication between your device and update servers.
If you still see the error message when you update or restore, contact Apple support.

HT2515 I have a Macbook Pro and an iPhone5. At one point, I received messages in sync on both devices. Now, I get some messages on the Macbook and others only on the iPhone. What happened?

I have a Macbook Pro and an iPhone5. At one point, I received messages in sync on both devices. Now, I get some messages on the Macbook and others only on the iPhone. What happened?

Associate your mobile number with your Apple ID, if you haven't already done so.
Sign out of iMessage on the Mac:
Messages ▹ Preferences ▹ Accounts ▹ Sign out
and on the iPhone:
Settings ▹ Messages ▹ Send & Receive ▹ Apple ID ▹ Sign out
Then, on the phone, tap
Use Your Apple ID for iMessage
Sign back into iMessage on both devices and test. If there's no change, you may have to wait for a change in network conditions.
Credit for this solution to ASC user SmittyLove and to Glenn Fleishman of tidbits.com.

What are correct settings on iCloud to make sure photos are on all devices?

What are correct settings on iCloud to make sure photos are on all devices?

If your Westell modem (actually, it is likely a gateway...a combination modem/router) is set up for "PPP is on the modem", then the AEBS should be configured to Connect Using = DHCP or Ethernet. The AEBS also needs to be configured in Bridge Mode.
Open AirPort Utility, click on the AEBS, and click Edit
Click the Internet tab and change to setting to "Connect Using DHCP"
Then click the Network tab and set the Router Mode for "Off (Bridge Mode)"
Update to save changes and restart the network by powering everything off in any order that you want. Then start the Westell device first, followed by the AEBS a minute later, etc until everything is powered back up.
This type of setup may work OK for you.
If not, you will need to change the Westell setup to "PPP is on the router" and then configure the AEBS to provide the PPPoE service as you did originally.
AT&T does generally advise that the modem should be in "Bridge Mode" or "PPP is on the router" when other routers are used with the "modem". See this document for more info:
http://www.att.com/esupport/article.jsp?sid=KB401764&cv=801,902&title=Connecting +a+non-AT%26T+provided+router+to+your+AT%26T+Internet+connection#fbid=43oi_bcpYy U

What are views in DDIC and plz mention the difference between them

hi,
What are views in DDIC and plz mention the difference between the different type of views..
1) maintainence view
2)database view
3)Projection view
4)help view
P.S : Good answers will be rewarded with points.

Hi,
The followings are different types of views:
- Database View   (SE11)
Database views are implement an inner join, that is, only records of the primary table (selected via the join operation) for which the corresponding records of the secondary tables also exist are fetched. Inconsistencies between primary and secondary table could, therefore, lead to a reduced selection set.
In database views, the join conditions can be formulated using equality relationships between any base fields. In the other types of view, they must be taken from existing foreign keys. That is, tables can only be collected in a maintenance or help view if they are linked to one another via foreign keys.
- Help View    ( SE54)
Help views are used to output additional information when the online help system is called.
When the F4 button is pressed for a screen field, a check is first made on whether a matchcode is defined for this field. If this is not the case, the help view is displayed in which the check table of the field is the primary table. Thus, for each table no more than one help view can be created, that is, a table can only be primary table in at most one help view.
- Projection View
Projection views are used to suppress or mask certain fields in a table (projection), thus minimizing the number of interfaces. This means that only the data that is actually required is exchanged when the database is accessed.
A projection view can draw upon only one table. Selection conditions cannot be specified for projection views.
- Maintenance View   ( SE54 )
Maintenance views enable a business-oriented approach to looking at data, while at the same time, making it possible to maintain the data involved. Data from several tables can be summarized in a maintenance view and maintained collectively via this view. That is, the data is entered via the view and then distributed to the underlying tables by the system
Thanks,
Shankar

HT4623 why does my ipad kick me out of FB and sometimes to the 'settings' page or sometimes to the desk top, for what reason? I have 50.8 GB of capacity available; it is version 5.1.1 and model MC497LL. it is WIFI and internet via AT&T??? Can you h

Can anyone help me? Why does my ipad kick me out of FB? Sometimes to the 'settings' page and sometimes to the desk top? I would like to know why this happens and what I can check or change to make it stop. I have 50.8 GB of capacity available; it is version IOS 5.1.1; model MC497LL. It is WIFI and internet via AT&T? Can anyone give me some clues on what to do; or change in settings??? Thank you very much!

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

I can't log in the App store because an from Zambia which is not listed in Apple outlets. How do i go around this as apple products are using globally and not only in the listed countries. My product is a Mac book pro.

I can't log in the App store because am from Zambia which is not listed in Apple outlets. How do i go around this as apple products are used globally and not only in the listed countries. My product is a Mac book pro. i feel this limits how i can use my product

Unfortunately you have taken an Apple product outside of the area where Apple currently does business. There isn't legally a way around this. Apple cannot license apps to you where you currently live.

HT4356 All my devices except my iPhone 4S can airprint. Only the 4s tells me no airprint printers found. I see no changes in the settings and I am on the same network.

All my devices except my iPhone 4S can airprint. Only the 4s tells me no airprint printers found. I see no differences in the settings and I am on the same network as the printer. Like I said, two iPads and an iPhone 4 airprint like a champ!

Appreciate the suggestion and tried it, but still, no joy. I even had another iPhone brought into the network and it found the printer, no problem. It's just this one iPhone 4s. Sounds like a trip to the Genius Bar for me!

Only about 2/3 of the column show. Also, paragraphs on sidebars, such as the Youtube subtitle sentences are cut so after the first line I only see the top of the second line.

Only about 2/3 of the column show. Also, paragraphs on sidebars, such as the Youtube subtitle sentences are cut so after the first line I only see the top of the second line.

If you have increased the minimum font size then try the default setting "none" as a high value can cause issues like you described.
* Firefox > Preferences > Content : Fonts & Colors > Advanced > Minimum Font Size (none)
* Firefox > Preferences > Content : Fonts & Colors > Advanced > [X] "Allow pages to choose their own fonts, instead of my selections above"
Reset the page zoom on pages that cause problems: <b>View > Zoom > Reset</b> (Ctrl+0 (zero); Cmd+0 on Mac)
* http://kb.mozillazine.org/Zoom_text_of_web_pages

What are some good visual effects programmes for the Mac?

I have been editing with Final Cut Express since 05 and I want to be able to do fancy visual effects I cannot do with Final Cut Express so I put it to you; what are some good visual effects programmes for the Mac? I know there is Adobe After Effects but I am wondering if there are any others, including from Apple.

Russ H wrote:
Or does it? Because by purchasing Motion, you also get the Pro Res codecs and Animation. Will FCE be able to work with them if they're in your QT library? I think so but am not positive. I'd check with the FCE gurus in that discussion forum.
So I half answered my own question. FCE will respect the alpha channel in a PR 4444 file. But from the limited testing I was able to to, there doesn't seem to be a way to export it ( or other flavors of PR) as a PR sequence. It renders as AIC, which is fine. FWIW, it can always be exported as Pro Res via QT Conversion, but why bother?
However, I now have to say – despite what I said in my first post – that I'm not 100% percent certain that the all the codecs will be available by buying Motion. I'm like 95% sure, the more I think about it. But I have too much NLE and graphics "stuff" on my systems to test it conclusively.
Russ

What are BI reports and ABAP reports and the difference between them ?

What are BI reports and ABAP reports and the difference between them? please explain me in detail and let me know if you have some documentation about it.
Thank you in advance!
Steve Jobs

Do we have to write custom code for the ABAP reports? Do you have any documentation about it?
Thank you.
Steve Jobs

If multiple users will be using the same iPad, how can I lock it so the settings cannot be changed, specifically the languages(students are changing the languages)?

If multiple users will be using the same iPad, how can I lock it so the settings cannot be changed, specifically the languages(students are changing the languages)?

Even with Apple Configurator most of the settings cannot be locked, and that includes the language settings. Most schools and organizations seem to just accept that they'll have to reconfigure the iPads on a regular basis.
Regards.

Is it possible to hide the save function and only use the save as function in teststand

Hi,
When i'm done building a sequence i want to prevent other engineers to save the sequence with the same filename (or version number).
Is it somehow possible to "hide" the save button and only use the save as function?
Or is there another possiblity to solve my problem.
The idea is to have a sequence called Sequence_V1.0.seq which i have build. When installing this in a factory enviroment I would like whenever there is a change needed in the sequence that the version number increases (manual action) (becomes Sequence_V1.1.seq). So from the moment you want to save i would like to only have the function save as. In this way you are obligated to fill in a new sequence name (original sequence will be read-only)
What would even be great if there could be a log of what the changes were
Thx!!!

1) You could mark the file as read-only, by default you would then not be able to save over it. The user could make it not read-only though if they know what they are doing.
2) Another possibility is to lock the sequence file for editing (this is a teststand feature). Go to the Sequence File Property dialog, on the advanced tab, where it says Password Protection, set it to Not Editable and give it a good password. This doesn't however keep someone from saving another file to the same name as the locked one, but they at least won't be able to saved the locked file again without your password, nor will they be able to edit it.
Hope this helps,
-Doug

What are the settings to remain only in the 5MHz mode?

Similar Messages

Maybe you are looking for