What is the corresponding DOM property to control the "Simulate Paper Color" option on Print dialog

I want to simulate the following manual steps in script:
Manual steps:
1. File->Print->Color Management
2. Click "Proof" radio button
3. Uncheck "Simulate Paper Color"
Script:
2. app.documents[0].printPreferences.sourceSpace = SourceSpaces.PROOF_SPACE;
3. ??? here I can't find the corresponding property or method to uncheck "Simulate Paper Color"

I think I have figure out the corresponding property, it is PrinterPreset.intent
Assigning PrinterPreset.intent to RenderingIntent.absoluteColorimetric equals to checking "Simulate Paper Color", assigning it to RenderingIntent.relativeColorimetric equals to unchecking the box.

Similar Messages

Whether the NI step controller can control the digital servo driver and motor

I want to you can help me confirm whether the NI step controller can control the digital servo driver and motor.If can,what is the differents between servo controller and step controller to control servo motor?Thank you so much!
Best regards

The PCI/PXI/FW 7344 high precision controller can be used to control both steppers and servo motors. The older PC Step controllers are made for stepper only control. The difference in the two control types is with stepper control, the controller outputs two digital signals that control the step and direction of the motor. The drive uses these digital signals to energize the stepper phases and commutate the motor. In a servo system, the controller outputs a -10 to 10 Volt analog signal that the drive then uses to output the appropriate current to the motor which is proportional to torque.
You can get more information from the following website:
http://zone.ni.com/devzone/devzone.nsf/webcategories/69771825AE23E98E86256786000BEA02?opendocument
Please let u
s know if you have any further questions.
Regards,
Andy Bell
Applications Engineer
National Instruments

During initial setup, I deleted the additional colored options in the Calender application. How do I get those colored options back? Thank you!!

During initial setup, I deleted the additional colored options in the Calender application. How do I get those colored options back? Thank you!!

Sounds like you have the print dialog minimised, as shown.
If you click the triangle next to the printer name, this will expand the print dialog and from this view you can see all the menu options as mentioned in the guide.

Is the iPad air able to control the Mackie 1608 digital mixer?

I am in the market for the Mackie 1608 mixer that uses the I-pad for control, question being will the Mackie work using the I-pad AIR?
Please advise. Thanks

The Mackie web page at http://www.mackie.com/products/dlseries/ says:
"Wireless control supported from all iPad models"
If it works with iPad 1-4, it should work with the Air model.
 Cheers, Tom

Using Javascript to rotate images with the style.backgroundImage property & I leave the onload pg & return, the images have trouble loading.

I'm using Javascript to rotate background images -->
function rotateImages() {
setInterval("startRotator()", 7000);
var counter = 0;
function startRotator() {
var images = ["images/finance1.jpg","images/finance2.jpg","images/finance3.jpg","images/finance4.jpg","images/finance5.jpg","images/finance6.jpg"];
if( counter >= images.length ) {
counter = 0;
var image = "url('" + images[counter] + "')";
counter++;
document.body.style.backgroundImage=image;
The script is triggered by the load event when the homepage loads and the script only runs on the homepage. Everything works fine upon opening the homepage.
If I leave the home page and return, the images will have trouble loading for about 3 to 5 cycles and I'll get white backgrounds for part of the time. The same thing happens if I enter the site from a page other than the homepage and then go to the homepage.
I discovered, however, that if I enter the site at the homepage and then leave the homepage and return using the back button, everything runs fine. Apparently it then accesses a cached version of the homepage? Seems having two cached versions creates a conflict?
This problem only happens with Firefox (I have ver 29.0.1). It does not happen on IE ver 11, Chrome ver 34, or Safari ver 5.1.7.
I get the same problem with XP, Win7, and Win8 but, only on Firefox.
Can you please fix this?

Hey, I am trying to reproduce this here: [http://jsfiddle.net/u3TLb/]
Mozillazine forums and the [http://webcompat.com] are more specialized in Web Compatibility, please ask there as well.

Could you please add to the smaller windows in mission control the icons to the open applications

Please Apple add this feature. I loved spaces and could see in the open windows better to know where I'm going. Just add the icons to the small windows and that should take care of the problem. I'm getting lost because I'm not sure which the application is in what window.

Apple don't read these forums, they're for user-to-user only. You want:
http://www.apple.com/feedback/macosx.html

What are the corresponding Data Types of some MDM Data Types

Hi Guys,
The MDM ABAP API involves creation of a DDIC structure in SRM. This structure should have the same fields with the MDM table fields. We would like to ask the corresponding ABAP Data Types for the following MDM Data Types.
MDM SRM
1. Look up (flat)
2. Look up (taxonomy)
3. Look up (heirarchy)
4. Look up (qualified flat look up)
Any significant inputs on this?
Thanks and regards,
RE

Hi,
Refer the below link. This is from the MDM Reference guide and contains the sample source code as well for almost all the things like creating repository, creating tables and fields etc. It would be helpful to you.
http://help.sap.com/saphelp_mdm550/helpdata/en/47/5fd3f7cbd75518e10000000a421138/frameset.htm
Regards,
Jitesh Talreja

How can I automatically control the channel selection on the data logger

I am an in-experienced use with a simple system which measures and displays temperature from 16 thermocouples. Not all 16 thermocouples are always connected at once and those that aren't are blanked off from view. I would also like to use the Advanced Data Logger VI to log the measurements but would like to have the logger only record or display the thermocouples that are connected. Un-connected channels give a signal of 1264 degrees so I can use a comparator to give a boolean output to switch them off. Can anyone please tell me how to do this.
Also, I need to expand the VI to read all 16 channels instead of the current 8. Any help would be appreciated

Mike,
Unfortunately I couldn't get the reference of the example you mention, probably you may want to add it as an attachment so the person who decides to answer this question knows exactly which example you are describing. So for the part of making visible/invisible some of the channels I attached an example that I built for demonstrating this feature, simply open the VI and run it, if you want one of the channels or plots from the graph to be invisible just click in the push button that corresponds to it. Switch to the block diagram and review the use of property nodes, using the property of visible.
If you want to generate a support request please visit www.ni.com/ask to see the options of reaching us.
Good luck!
Nestor Sanchez
Applications Engine
er
National Instruments
Nestor
National Instruments
Attachments:
Visible_Plots.vi ‏46 KB

What is use of content-property in itemdescriptor

Hi
what is use of content-property in item descriptor? In which scenario it is used? Found below from ATG Docs, but still not clear.
http://docs.oracle.com/cd/E24152_01/Platform.10-1/ATGRepositoryGuide/html/s1403contentattributesandproperties01.html
Thanks In Advance.
Gopi

content-property is used in case of content repositories which has content repository items. Content repository is used just like regular SQL repositories. A content repository item can be thought as consisting of some content and its metadata. The content-property attribute is used in the content item-descriptor and is usually the name of the property that holds the content itself.
E.g. "media" as you mentioned. Here the metadata might include properties like name, description, type, date of creation, keywords etc. while the content would include the binary-data of the media itself (in case of internal media type). So the declaration content-property="data" in the media item descriptor signifies that property called "data" in the media item will be holding the actual content. You can find more details about it and content repositories in the ATG Repository documentation.
Edited by: Nitin Khare on Aug 16, 2012 6:59 AM

No object type found for the corresponding message in BPM

Hi All,
I have a BPM scenario where i pick a file and based on a condition in the Switch i send the meesage to Mail or Proxy.
When i tested the scenario i got error as "no object type found for the message check the corresponding process activated" error in the call adapter step.
I checked in sxi_cache, IP is active with 0 as return code .
When checked in sxmb_moni_bpe, under process selection it says "No workitem exists"
In SXMB_MONI, under inbound i clicked PE but got error as "Unable to perform action fro the selected Message" is displayed.
Im new to BPM so please tell me as what Im missing exactly.
Thanks

Hi Sachi,
Delete the Integration Process from ID and reimport it. Also check the status of your BPM in T Code SXI_CACHE....if return code is not '0' then re-activate your integration process..
Try REPEAT ACTIVATION on SXI_CACHE...
Have a look into this..
Re: Stuck in BPM Transformation process Async to Sync Scenario
Regds,
Pinangshuk.

How do I control the TEK TDS3052 by LABVIEW installed in a PC?

I used the "crossover" cable directly connect the PC and the TEK TDS3052(with a ethernet port).What I have done is that I configured the ethernet parameters( the IP adress, the net mask etc.). And when I apply the "Ping" command in the "run" window of the windows 98, there is a correct return.So the ethernet network is well done.Now I want to use the LABVIEW to control the oscilloscope. But I don't know then.Who can tell me the detail steps which I can take next, thanks a lot.

Kevin,
Which version of LabVIEW do you have?
There are two ways of controlling your oscilloscope from LabVIEW, one is using the VISA functions (instrument i/o palette in LabVIEW)and another one is using an already built instrument driver, which you can download by going to zone.ni.com, and then click on "resource library" at your left... then click in "instrument drivers", and then in "downloads" and then type in the "additional keywords" box type "tds 3052" and click SEEK... you will find a link for your instrument there... you can download that instrument driver and it fully functional with LabVIEW, now... the truth is that I have always used this drivers with a GPIB interface in the computer, in this case is only going to be by TCP/IP... so you can try to adapt the addresses instead of using an instrument type address, use the TCP/IP instrument type address and give it a try to see if it works. The address type for TCP/IP is stated below.
First you need to have the latest version of NI-VISA installed, 2.5.2, which is shipped with LabVIEW 6i (version 2.5.0 and then download a patch for 2.5.2).
Our solution for controlling instruments with Ethernet ports is NI-VISA.There are two possible situations:
1) Instrument supports the VXI-11 protocol.
The VXI-11 protocol was created to control instruments over Ethernet using the GPIB style. It has nothing to do with VXI, but it was there were it got approved.
NI-VISA supports VXI-11 instruments, to the point that the only change in the instrument driver written with VISA is the identification string. Instead of using GPIB::1::INSTR, you can use TCPIP::ip address::instrument name::INSTR. (For example, with the Tek TDS 3054, the string would be: TCPIP::130.130.130.1::gpib0,1::INSTR). (Note that 'gpib0,1' has nothing to do GPIB..its just a name given to the instrument..it could have been just 'tds3054' also if the instrument vendor chose to do so).
2) Instrument DOES NOT support the VXI-11 protocol.
In this case, you can still use NI-VISA to talk to the instrument using the NI-VISA Ethernet Sockets functions. However, you would have to take care of the specifics of the protocol used for the instrument. The instrument manufacturer should provide you with the details on how to control the instrument (commands, parsing, etc.).
*** Tek's Scopes ***
Tek introduced an ethernet interface for some of their scopes. We have a TDS3054 scope from Tek that is VXI-11 compliant. Since the TDS3054 is VXI-11 compliant, we used it at NIWeek to show how you could control it using the same code written for the instrument with the GPIB interface, by just changing the identification string.
NI-VISA 2.5.2
NI-VISA 2.5.0 introduced the support for instruments with Ethernet ports. Notice that LabVIEW 6i ships with the older 2.5.0 version. The patch to upgrade it to 2.5.2 is called NiViEnet.dll and is located in the ftp site at:
ftp://ftp.natinst.com/support/visa/drivers/win32/2.5/patch/
So you can try this Kevin and see if it works for you, contact us back (www.ni.com/ask) if you need further assistance.
Good luck!...
Nestor Sanchez
Applications Engineer
National Instruments
Nestor
National Instruments

How to control the R/3 prod and BW prod when diff teams works at the same

Hi Friends,
I would like to check with you guys, I'm working for support project at the same time different teams are using same server.
If the different teams are being used same Master data as well, We don't know what are the teams developing which are the objects.
Now the problem is when we check in the BW production every time having probem e.g: Inactive Masterdata Info Object, ODS replication etc.
I would like to ask you guys, Normally this being the case, How we can control the R/3 Production and BW production.
Can anybody give some valuable inputs...if it's applicable we'll implements in my project as well.
SIRI

Hi Siri
If am correct , your concern is when a development team sends some objects to production as part of their project, you see discrepencies of some master data being inactive .
Your Question is,How to coordinate those?
You sais you are working for Support means Data loads, then development team also works for the same server moving to Prod. then obviously there should be soem integration of all the teams for the work going live in production, maintain a call with all your team when and all objects are moving to Production and check if any impact of those objects for you when they are moved to Prod.
But all the time objects moved to prod will be supported by the development team for short period for its stabilization there.
Hope you need to have coordination with the team .......
Regards

Volume control sometimes gets stuck controlling the wrong volume - bug report?

Occasionally the volume control hard buttons on my Pre go wonky and "stick" to controlling an application as opposed to what they are supposed to. For example, I'll use the music player, and it will function fine and show the musical note when adjusting the volume. Then I'll toss away the music player app, but the volume will "stick" with the musical note and not control the system and ringer sound volumes.
This feels like a bug, but I might be missing something. Thanks!
Post relates to: Pre p100eww (Sprint)

Don't think your missing anything. Its a bug, I have encountered a few times. Seems like most the time, it has happened to me if I immediately try to change the volume after tossing a card away such as music player, or video. But have had it happen a few times without any explanation. Restarting it fixes it, and luckily it does not happen that often for me. Just wanted to chime in to say its not just you though.

I have a plot with two cursors - how can I control the "visible" attribute of the second cursor?

I have a waveform graph with multiple plots and two cursors. I can use the "cursor->visible" property to control cursor #1 but I cannot seem to find a way to control the visible attribute for cursor #2. Is there a way to do this?
Thanks,
RGA

There's an "Active Cursor" property that allows you select which cursor the following actions operate on. Remember that property nodes "execute" from top to bottom...
Mike...
Certified Professional Instructor
Certified LabVIEW Architect
LabVIEW Champion
"... after all, He's not a tame lion..."
Be thinking ahead and mark your dance card for NI Week 2015 now: TS 6139 - Object Oriented First Steps

Can I control the mouse pointer?

I would like to know is there any classes in the API that I can control the mouse pointer(cursor) like the one that is done in JavaScript? I couldn't find anything about it. In MouseEvent, the only thing that I found was getX() and getY() that will not assign the location to the current cursor. Since I need to do a First Person View mode stuff, I need to use mouse to pan and this is very important, thank you for all your repies.
Andy

I've never used it, but it appears the Robot class is what you are looking for.
http://java.sun.com/j2se/1.4.2/docs/api/java/awt/Robot.html

What is the corresponding DOM property to control the "Simulate Paper Color" option on Print dialog

Similar Messages

Maybe you are looking for