What is the xml,why it is.....

Hi developers...
I am new for xml.please explain patiently.I don't know what is the xml, why xml and how to write xml code.please help me.
Thank u
reguards
sure

Hi,
To understand the XML:
1. http://www.w3.org/XML/
2. http://www.xml.org/xml/resources_focus_beginnerguide.shtml
To understand Java with XML - This place is the best
http://java.sun.com/xml/faq.html
Hope it could answere your question
With Cheers,
Prasanna

Similar Messages

What are the reasons why a wideband modem can not take a CPE?

I have an M-CMTS with RFGW1.
I have the following settings:
int c6/1/3
downstream Modular-Cable 1/0/0 rf-channel 16-17 upstream 0-3
int c6/1/4
downstream Modular-Cable 1/0/0 rf-channel 18-19 upstream 0-3
cable fiber-node 9
downstream Modular-Cable 1/0/0 rf-channel 16-19
downstream Cable6/1/3
upstream Cable 6/1 connector 12-15
cable fiber-node 10
downstream Modular-Cable 1/0/0 rf-channel 16-19
downstream Cable6/1/4
upstream Cable 6/1 connector 16-19
interface Wideband-Cable1/0/0:4
load-interval 30
cable bundle 1
cable bonding-group-id 5
cable rf-channel 16 bandwidth-percent 45
cable rf-channel 17 bandwidth-percent 45
cable rf-channel 18 bandwidth-percent 45
cable rf-channel 19 bandwidth-percent 45
the cable modem gets online, but does not take cpe, my question is why?
D2.0 modems do take CPE, but the 3.0 modems do not. I know that may be a problem in the RFGW1 because another time I changed the port and it worked.
but I would like to know the reason why only the wideband modems are not taking cpe.
I'd like to hear from you.
thanks in advance

Hi Diego,
- The first time that was put online, it became as w-online and take CPE (The DHCP assigned IP addresses both, Modem and CPE)- But it did not work, so I reset the modem, and went online again, (but did not have a CPE IP address)
I'm not following you here. In the first point you mentioned that the modem came w-online and the CPE got an IP. However, in the second point, you mentioned that it didn't work and then you reset the modem. What didn't work (I understood the problem was CPE getting IP address which, as you mentioned, was done on the first point)?
You also said that, at some point, the modem was online but not pingable. The CPE didn't get IP that time. In that case, was the modem online or w-online? What was the primary channel for this modem? Take into account that, for wideband, the modem uses the primary channel to register and perform all Docsis operation. Any data traffic (like a ping or a DHCP request from a CPE) will use the secondary channels. If these channels have some issue you may see an issue as the one described.
For the D2.0 modem using Mo1/0/0:16, it could be similar as above. If this channel is OK but the rest have some issues, you could see a behavior like that. The D2.0 modem will use the primary channel (only channel) also for data transfer. Since this channel is OK, the D2.0 modem don't have any issue. However, if a D3.0 modem uses Mo1/0/0:16 as primary it may come online (since the channel is OK) but, if the rest of channels have issues, then you may have problem to pass data traffic.
Did you check if D2.0 modem can use all the channels? You may also want to check the modulation profiles being used. It could be that you are using a lower modulation profile for ranging (initial, station maintenance) and a higher one for data transfer which may be affected by some condition in the network.
Best regards.

What's the xml for this?

I am running on a tomcat server and have not been able to find what the xml is to create a uri to a resource other than a servlet. how do I edit the web.xml file to create a uri to a webpage or image?

To give you an example of what I am talking about (I'm the author of the post, this is just a diff acount) if I wanted to make a uri to link to a servlet on tomcat I would add this to the web.xml file in WEB-INF:
<servlet>
<servlet-name>Anything</servlet-name>
<servlet-class>Name of servlet class (w/o .class at the end)</servlet-class>
</servlet>
<servlet-mapping>
<servlet-name>The servlet name defined above</servlet-name>
<url-pattern>(Anything i'll use->) /Servlet/</url-pattern>
</servlet-mapping>
then when you want to link to the servlet in say, a form you would write the following in an html file:
<form action="/Servlet/" method="Post">
you can do the same thing with a link:
text
What I am curious to know is: How do I do this if I want the uri to link to an image? (I know for a page I can just link to a servlet that just forwards you to a page) I've tried changing the servlet-class to another resource, but that doesn't work. Does anyone know how to do this?

What is the purpose why we define partner determination

hi
my question is what is use of partner determination. How many partner functions we should create in customer master. Is there any thumb rule we have create sd,bp,py,sh
thanks in advance

Hi,
We sell the goods to the customer who places the order. In SAP this ordering customer role is played by the sold to party. Similarly the shipping address is the ship to party used while creating the delivery. While creating the invoice we require the bill to party and for receiving the payment payer function is required. Hence partner determination procedure is very important in SD from the sales flow point of view otherwise if you create the customer without any partner function then you will not be able to create even the sales order.
SP, SH, BP & PY are the basic partner functions. Apart from this you can create partner function for commission agent, notifying party, sales employee, etc. You will find this in IMG-sales & distribution - basic functions - partner determination - set up partner determination. Click here and you will see
1.Set Up Partner Determination for Customer Master
2.Set Up Partner Determination for Sales Document Header
3.Set Up Partner Determination for Sales Document Item
4.Set Up Partner Determination for Delivery
5.Set Up Partner Determination for Shipment
6.Set Up Partner Determination for Billing Header
7.Set Up Partner Determination for Billing Item
8.Set Up Partner Determination for Sales Activities (CAS)
Just go through the documentation below. You will get a clear picture on how to do the partner determination procedure for a customer.
PARTNER DETERMINATION PROCEDURE
First go to OBD2 create customer account groups. Here you make new entries, click whether it is a one time customer, description. Also you can do the field selection here for general data, co. code data and sales area data.
Now go to IMG logistics general business partner customers control define & assign customer number ranges. Here you define the number range that you want and assign it to your customer account group.
Now go to VOPA here the selection will be on customer master, click on partner procedures, create the partner determination procedure. After saving it double click on it then you will face with a screen. Here you enter the partner function and you can select if you want the function as mandatory and not changeable.
Then go back, click on procedure assignment, enter your account group in the lower left corner of the screen, press enter then in front of that select your partner determination procedure. Then save it.
Then click on go back 2 times. Here you can see partner functions, click on it, then go to environment in the upper menu and select Acct. grp assignment. Here just select your partner function and in front of that you select your customer account group. Then save it. Now you have completed the pre requisites to create the customer master.
Then go to XD01 and create your customer master.
<REMOVED>
Regards,
Allabaqsh G. Patil
Message was edited by:
Yathish K

What are the reasons why Server Assistant won't detect Auto Server Setup ?

Hi there,
I've been having issues with Auto Server Setup mechanism (the mechanism that allows an administrator to install a machine without human user interaction). I actually have the answer to my post question but I post it anyway because it might help someone that stumbles on the same issue. Moreover, the answer raises other questions about licencing.
I had the problem that I had created a NetInstall image that had a "/Auto Server Setup/generic.plist" file; this worked perfectly on the XServe I was testing it on : when I started the client in NetBoot mode, the client was installing without any human interaction, from the disk formatting to the login window... all this was pefectly good. Then I tried to install another machine by starting it in NetBoot mode : the machine installed the system and then waited for human interaction for the configuration step in Server Assistant, as is there was no "/Auto Server Setup/generic.plist" file....
I finally managed to figure out what was wrong (not thanks to Apple, as I couldn't find any clue : no message from "Server Assistant", nothing useful in the logs I found just by luck in /Library/Logs/ServerAssistant.log) : my "/Auto Server Setup/generic.plist" was ignored because of the Mac OS X licence key. When I replaced the key in generic.plist with another key, it started working again. I know that the official documentation says to use site licences when using the generic.plist mechanism but at least an error message somewhere would have helped...
So, it seems that "Server Assistant" talks to apple servers and refuses to use a licence key that is used somewhere else. These policies are perfectly fine, as long as it works and it is consistent, which I'm not convinced of :
- first, we had success in the past in duplicating Mac OS X 10.5 system disk images (we have lots of xserves with valid licence keys but we found it easier to duplicate system disk images) on our xserves, and even if all xserves had the same osx server licence key, they worked fine (except that Server Admin doesn't like it). As a result, the licence verification policy is inconsistent as it depends on the way mac osX is installed...
- second, I'm not sure this licence checking mechanism even works : I beleive that apple registers associations between a machine id and a licence key; then, how does apple guarantees that this association (therefore free the licence key) is removed when you format a system hard drive (there is no other way to uninstall Mac OSX, right ?) ?
Does anyone knows how licence key registration works and more specifically how licence keys get freed for reuse on another machine ?

Hi Stephen,
To login, the internal server should be: https://boot.ciscojabbervideo.com/endpoint/configuration
The external server and domain fields are blank.
Your username only needs the prefix of your @jabber.com video address. For example, if your video address is [email protected] then your username is "stephen."
Unfortunately, there is only forum support for this free service.
Regards,
Jason

What is the XML format for Sub Agreements?

Hi,
We have requirement to automate loading Master Agreements and Sub Agreements into CLM from a non-SAP system.
Currently the data is loaded using CSV files, but Double Byte Char. is not supported in CSV file format.
I am trying to load using XML format and have be successful to load Master Agreement.
I need help with Sub Agreement XML Structure or a better alternative to load Sub Agreement metadata containing Double Byte Char.
Provided below is the Sub Agreement XML Structure. Please provide suggestions or guidance on this issue.
We are on 7.0 SP8 .
Thanks
Sai

Hi Prasad,
Thanks for your quick response.
I am able to load successfully Project and Master Agreement in XML format with metadata containing multibyte char.
Multibyte char is displayed on Project and Master Agreement Screen.
English , German, Chinese, Japanese, Korean, Spanish, French and Italian language packs are installed in Sourcing.
I am getting below error while importing XML for Sub Agreement.
Record 1. Warning: XML import could not process field: CONTRACT_UNIQUE_DOC_NAME
Facility=local4;sessionid=bR6bHsKNs_s_sA8ihHdOSyOASPCvRgEP3icA_SAP;tenantid=#ebay#;username=sguntaka;exception=java.lang.IllegalArgumentException: unsupported null bind parameter no. 0 found in statement SELECT OBJECTID, CONTEXTID, REVISION_COUNT, UNIQUE_DOC_NAME, DISPLAY_NAME, COLLN_METADATA, RESERVATION_LOCK, DOCUMENT_DESCRIPTION, CREATED_BY_USER_OBJECT_ID, CREATED_BY_USER_CLASS_ID, CREATED_BY_USER_OBJECT_NAME, MODIFIED_BY_USER_OBJECT_ID, MODIFIED_BY_USER_CLASS_ID, MODIFIED_BY_USER_OBJECT_NAME, EDIT_BY_USER_OBJECT_ID, EDIT_BY_USER_CLASS_ID, EDIT_BY_USER_OBJECT_NAME, CREATED_AT, MODIFIED_AT, EDIT_AT_DATETIME, INACTIVE, TRACK_CHANGES, COLLABORATION_POLICY, HAS_PUBLIC_DISC, IS_TEMPLATE, CANCELED_BY_USER_OBJECT_ID, CANCELED_BY_USER_CLASS_ID, CANCELED_BY_USER_OBJECT_NAME, DOC_OWNER_USER_OBJECT_ID, DOC_OWNER_USER_CLASS_ID, DOC_OWNER_USER_OBJECT_NAME, CLOSED_BY_USER_OBJECT_ID, CLOSED_BY_USER_CLASS_ID, CLOSED_BY_USER_OBJECT_NAME, CANCELED_AT, CLOSED_AT, TEMPLATE_OBJECT_ID, TEMPLATE_CLASS_ID, TEMPLATE_OBJECT_NAME, DOC_TYPE_OBJECT_ID, DOC_TYPE_CLASS_ID, DOC_TYPE_OBJECT_NAME, BASE_DATE_DATE, SCHEDULE_WORK_DAYS, BUSINESS_UNIT_OBJECT_ID, BUSINESS_UNIT_CLASS_ID, BUSINESS_UNIT_OBJECT_NAME, COMPANY_OBJECT_ID, COMPANY_CLASS_ID, COMPANY_OBJECT_NAME, ESTIMATED_CURRENCY, ESTIMATED_OBJECT_ID, ESTIMATED_PRICE, BUDGETED_CURRENCY, BUDGETED_OBJECT_ID, BUDGETED_PRICE, CURRENCY_OBJECT_ID, CURRENCY_CLASS_ID, CURRENCY_OBJECT_NAME, VENDOR_VISIBLE, DATE_TO_PUBLISH_DATE, LOCK_BASELINE, LI_PERIOD_TYPE_OBJECT_ID, LI_PERIOD_TYPE_CLASS_ID, LI_PERIOD_TYPE_OBJECT_NAME, CALC_METHOD, SPEC_ID_COUNT, ATTR_ID_COUNT, FORMULA_ID_COUNT, PURCHASING_ORG_OBJECT_ID, PURCHASING_ORG_CLASS_ID, PURCHASING_ORG_OBJECT_NAME, PURCHASING_GRP_OBJECT_ID, PURCHASING_GRP_CLASS_ID, PURCHASING_GRP_OBJECT_NAME, TRANSACTION_TYPE_OBJECT_ID, TRANSACTION_TYPE_CLASS_ID, TRANSACTION_TYPE_OBJECT_NAME, COMPANY_CODE_OBJECT_ID, COMPANY_CODE_CLASS_ID, COMPANY_CODE_OBJECT_NAME, INTEGRATED_TYPE, USE_ERP_VALIDATION, STORAGE_LOCATION, RECORD_SERIES, RETENTION_DATE_DATE, RETENTION_REMINDER_DATE_DATE, RETENTION_EVENT_OBJECT_ID, RETENTION_EVENT_CLASS_ID, RETENTION_EVENT_OBJECT_NAME, EFFECTIVE_DATE_DATE, EXPIRATION_DATE_DATE, TERMIN_NOTICE_LEAD_TIME, TERMIN_COMMU_DATE, PERPETUAL_TERM, AUTO_RENEWAL, EVENT_OBJECT_ID, EVENT_CLASS_ID, EVENT_OBJECT_NAME, RENEWAL_REMINDER_DATE, VENDOR_OBJECT_ID, VENDOR_CLASS_ID, VENDOR_OBJECT_NAME, CONTACT_OBJECT_ID, CONTACT_CLASS_ID, CONTACT_OBJECT_NAME, LOCATION_OBJECT_ID, LOCATION_CLASS_ID, LOCATION_OBJECT_NAME, PAYTERMS_OBJECT_ID, PAYTERMS_CLASS_ID, PAYTERMS_OBJECT_NAME, REPLENISHMENT_OBJECT_ID, REPLENISHMENT_CLASS_ID, REPLENISHMENT_OBJECT_NAME, VENDOR_ACCT_NUM, INT_CAT_OBJECT_ID, INT_CAT_CLASS_ID, INT_CAT_OBJECT_NAME, EXT_CAT_OBJECT_ID, EXT_CAT_CLASS_ID, EXT_CAT_OBJECT_NAME, EVALUATION_CRITERIA, NEXT_AUDIT_DATE, LAST_AUDIT_DATE, TOTAL_EXPECTED_CURRENCY, TOTAL_EXPECTED_OBJECT_ID, TOTAL_EXPECTED_PRICE, TOTAL_BUDGETED_CURRENCY, TOTAL_BUDGETED_OBJECT_ID, TOTAL_BUDGETED_PRICE, TOTAL_ACTUAL_CURRENCY, TOTAL_ACTUAL_OBJECT_ID, TOTAL_ACTUAL_PRICE, TOTAL_SAVINGS_CURRENCY, TOTAL_SAVINGS_OBJECT_ID, TOTAL_SAVINGS_PRICE, TOTAL_COST_SAVINGS_CURRENCY, TOTAL_COST_SAVINGS_OBJECT_ID, TOTAL_COST_SAVINGS_PRICE, TOTAL_COST_AVOIDANCE_CURRENCY, TOTAL_COST_AVOIDANCE_OBJECT_ID, TOTAL_COST_AVOIDANCE_PRICE, PERF_EVAL_CRITERIA, PERF_LAST_UPDATE_DATE, PERF_NEXT_UPDATE_DATE, BUYER_SEARCHABLE, VAL_PERIOD_TYPE_OBJECT_ID, VAL_PERIOD_TYPE_CLASS_ID, VAL_PERIOD_TYPE_OBJECT_NAME, INCLUDE_PART_NUMBER, TOTAL_ACTUAL_SPEND_CURRENCY, TOTAL_ACTUAL_SPEND_OBJECT_ID, TOTAL_ACTUAL_SPEND_PRICE, FORECAST_SPEND_CURRENCY, FORECAST_SPEND_OBJECT_ID, FORECAST_SPEND_PRICE, ACTUAL_LIMIT_PCT, FORECAST_LIMIT_PCT, LINEITEM_ID_CNT, LIMIT_VALUE_CURRENCY, LIMIT_VALUE_OBJECT_ID, LIMIT_VALUE_PRICE, MINIMUM_VALUE_CURRENCY, MINIMUM_VALUE_OBJECT_ID, MINIMUM_VALUE_PRICE, MINIMUM_DAYS_OFFSET, MARGIN_PRICING, DELETED_AT_DATETIME, DELETED_BY_OBJECT_ID, DELETED_BY_CLASS_ID, DELETED_BY_OBJECT_NAME, CTR_IS_DUET, HAS_DUET_ITEMS, WORD_ATTRIBUTES_TEXT_PREVIEW, WORD_ATTRIBUTES_TEXT_OBJECT_ID, WORD_ATTRIBUTES_TEXT_CLASS_ID, WORD_ATTRIBUTES_CHECKSUM, SENT_TO_ERP_DATETIME, STATUS_OBJECT_ID, STATUS_CLASS_ID, STATUS_OBJECT_NAME, LAST_SPEND_IMPORT_DATE, BUYER_SPECS_SUPPORT, VENDOR_SPECS_SUPPORT FROM clmuser.FCI_CONTRACT WHERE UNIQUE_DOC_NAME = ? AND CONTEXTID = ?;stacktrace=java.lang.IllegalArgumentException: unsupported null bind parameter no. 0 found in statement SELECT OBJECTID, CONTEXTID, REVISION_COUNT, UNIQUE_DOC_NAME, DISPLAY_NAME, COLLN_METADATA, RESERVATION_LOCK, DOCUMENT_DESCRIPTION, CREATED_BY_USER_OBJECT_ID, CREATED_BY_USER_CLASS_ID, CREATED_BY_USER_OBJECT_NAME, MODIFIED_BY_USER_OBJECT_ID, MODIFIED_BY_USER_CLASS_ID, MODIFIED_BY_USER_OBJECT_NAME, EDIT_BY_USER_OBJECT_ID, EDIT_BY_USER_CLASS_ID, EDIT_BY_USER_OBJECT_NAME, CREATED_AT, MODIFIED_AT, EDIT_AT_DATETIME, INACTIVE, TRACK_CHANGES, COLLABORATION_POLICY, HAS_PUBLIC_DISC, IS_TEMPLATE, CANCELED_BY_USER_OBJECT_ID, CANCELED_BY_USER_CLASS_ID, CANCELED_BY_USER_OBJECT_NAME, DOC_OWNER_USER_OBJECT_ID, DOC_OWNER_USER_CLASS_ID, DOC_OWNER_USER_OBJECT_NAME, CLOSED_BY_USER_OBJECT_ID, CLOSED_BY_USER_CLASS_ID, CLOSED_BY_USER_OBJECT_NAME, CANCELED_AT, CLOSED_AT, TEMPLATE_OBJECT_ID, TEMPLATE_CLASS_ID, TEMPLATE_OBJECT_NAME, DOC_TYPE_OBJECT_ID, DOC_TYPE_CLASS_ID, DOC_TYPE_OBJECT_NAME, BASE_DATE_DATE, SCHEDULE_WORK_DAYS, BUSINESS_UNIT_OBJECT_ID, BUSINESS_UNIT_CLASS_ID, BUSINESS_UNIT_OBJECT_NAME, COMPANY_OBJECT_ID, COMPANY_CLASS_ID, COMPANY_OBJECT_NAME, ESTIMATED_CURRENCY, ESTIMATED_OBJECT_ID, ESTIMATED_PRICE, BUDGETED_CURRENCY, BUDGETED_OBJECT_ID, BUDGETED_PRICE, CURRENCY_OBJECT_ID, CURRENCY_CLASS_ID, CURRENCY_OBJECT_NAME, VENDOR_VISIBLE, DATE_TO_PUBLISH_DATE, LOCK_BASELINE, LI_PERIOD_TYPE_OBJECT_ID, LI_PERIOD_TYPE_CLASS_ID, LI_PERIOD_TYPE_OBJECT_NAME, CALC_METHOD, SPEC_ID_COUNT, ATTR_ID_COUNT, FORMULA_ID_COUNT, PURCHASING_ORG_OBJECT_ID, PURCHASING_ORG_CLASS_ID, PURCHASING_ORG_OBJECT_NAME, PURCHASING_GRP_OBJECT_ID, PURCHASING_GRP_CLASS_ID, PURCHASING_GRP_OBJECT_NAME, TRANSACTION_TYPE_OBJECT_ID, TRANSACTION_TYPE_CLASS_ID, TRANSACTION_TYPE_OBJECT_NAME, COMPANY_CODE_OBJECT_ID, COMPANY_CODE_CLASS_ID, COMPANY_CODE_OBJECT_NAME, INTEGRATED_TYPE, USE_ERP_VALIDATION, STORAGE_LOCATION, RECORD_SERIES, RETENTION_DATE_DATE, RETENTION_REMINDER_DATE_DATE, RETENTION_EVENT_OBJECT_ID, RETENTION_EVENT_CLASS_ID, RETENTION_EVENT_OBJECT_NAME, EFFECTIVE_DATE_DATE, EXPIRATION_DATE_DATE, TERMIN_NOTICE_LEAD_TIME, TERMIN_COMMU_DATE, PERPETUAL_TERM, AUTO_RENEWAL, EVENT_OBJECT_ID, EVENT_CLASS_ID, EVENT_OBJECT_NAME, RENEWAL_REMINDER_DATE, VENDOR_OBJECT_ID, VENDOR_CLASS_ID, VENDOR_OBJECT_NAME, CONTACT_OBJECT_ID, CONTACT_CLASS_ID, CONTACT_OBJECT_NAME, LOCATION_OBJECT_ID, LOCATION_CLASS_ID, LOCATION_OBJECT_NAME, PAYTERMS_OBJECT_ID, PAYTERMS_CLASS_ID, PAYTERMS_OBJECT_NAME, REPLENISHMENT_OBJECT_ID, REPLENISHMENT_CLASS_ID, REPLENISHMENT_OBJECT_NAME, VENDOR_ACCT_NUM, INT_CAT_OBJECT_ID, INT_CAT_CLASS_ID, INT_CAT_OBJECT_NAME, EXT_CAT_OBJECT_ID, EXT_CAT_CLASS_ID, EXT_CAT_OBJECT_NAME, EVALUATION_CRITERIA, NEXT_AUDIT_DATE, LAST_AUDIT_DATE, TOTAL_EXPECTED_CURRENCY, TOTAL_EXPECTED_OBJECT_ID, TOTAL_EXPECTED_PRICE, TOTAL_BUDGETED_CURRENCY, TOTAL_BUDGETED_OBJECT_ID, TOTAL_BUDGETED_PRICE, TOTAL_ACTUAL_CURRENCY, TOTAL_ACTUAL_OBJECT_ID, TOTAL_ACTUAL_PRICE, TOTAL_SAVINGS_CURRENCY, TOTAL_SAVINGS_OBJECT_ID, TOTAL_SAVINGS_PRICE, TOTAL_COST_SAVINGS_CURRENCY, TOTAL_COST_SAVINGS_OBJECT_ID, TOTAL_COST_SAVINGS_PRICE, TOTAL_COST_AVOIDANCE_CURRENCY, TOTAL_COST_AVOIDANCE_OBJECT_ID, TOTAL_COST_AVOIDANCE_PRICE, PERF_EVAL_CRITERIA, PERF_LAST_UPDATE_DATE, PERF_NEXT_UPDATE_DATE, BUYER_SEARCHABLE, VAL_PERIOD_TYPE_OBJECT_ID, VAL_PERIOD_TYPE_CLASS_ID, VAL_PERIOD_TYPE_OBJECT_NAME, INCLUDE_PART_NUMBER, TOTAL_ACTUAL_SPEND_CURRENCY, TOTAL_ACTUAL_SPEND_OBJECT_ID, TOTAL_ACTUAL_SPEND_PRICE, FORECAST_SPEND_CURRENCY, FORECAST_SPEND_OBJECT_ID, FORECAST_SPEND_PRICE, ACTUAL_LIMIT_PCT, FORECAST_LIMIT_PCT, LINEITEM_ID_CNT, LIMIT_VALUE_CURRENCY, LIMIT_VALUE_OBJECT_ID, LIMIT_VALUE_PRICE, MINIMUM_VALUE_CURRENCY, MINIMUM_VALUE_OBJECT_ID, MINIMUM_VALUE_PRICE, MINIMUM_DAYS_OFFSET, MARGIN_PRICING, DELETED_AT_DATETIME, DELETED_BY_OBJECT_ID, DELETED_BY_CLASS_ID, DELETED_BY_OBJECT_NAME, CTR_IS_DUET, HAS_DUET_ITEMS, WORD_ATTRIBUTES_TEXT_PREVIEW, WORD_ATTRIBUTES_TEXT_OBJECT_ID, WORD_ATTRIBUTES_TEXT_CLASS_ID, WORD_ATTRIBUTES_CHECKSUM, SENT_TO_ERP_DATETIME, STATUS_OBJECT_ID, STATUS_CLASS_ID, STATUS_OBJECT_NAME, LAST_SPEND_IMPORT_DATE, BUYER_SPECS_SUPPORT, VENDOR_SPECS_SUPPORT FROM clmuser.FCI_CONTRACT WHERE UNIQUE_DOC_NAME = ? AND CONTEXTID = ?
at com.sap.odp.common.db.AbstractDb.findWhere(AbstractDb.java:5823)
at com.sap.odp.common.db.AbstractDb.findWhere(AbstractDb.java:5760)
at com.sap.eso.contracts.ContractHome.findUniqueByDocName(ContractHome.java:96)
at com.sap.eso.contracts.importer.processors.AgreementProcessor.createNewHook(AgreementProcessor.java:479)
at com.sap.odp.doc.importer.AbsDocImportProcessor.processRow(AbsDocImportProcessor.java:165)
at com.sap.odp.common.install.dataimport.csv.CsvFileProcessor.processRowInternal(CsvFileProcessor.java:1370)
at com.sap.odp.common.install.dataimport.csv.CsvFileProcessor.processFile(CsvFileProcessor.java:281)
at com.sap.odp.common.install.dataimport.xml.XmlImporter.importXmlObject(XmlImporter.java:249)
at com.sap.odp.common.install.dataimport.xml.XmlImportHandler.endElement(XmlImportHandler.java:155)
at org.apache.xerces.parsers.AbstractSAXParser.endElement(Unknown Source)
at org.apache.xerces.impl.XMLDocumentFragmentScannerImpl.scanEndElement(Unknown Source)
at org.apache.xerces.impl.XMLDocumentFragmentScannerImpl$FragmentContentDispatcher.dispatch(Unknown Source)
at org.apache.xerces.impl.XMLDocumentFragmentScannerImpl.scanDocument(Unknown Source)
at org.apache.xerces.parsers.XML11Configuration.parse(Unknown Source)
at org.apache.xerces.parsers.XML11Configuration.parse(Unknown Source)
at org.apache.xerces.parsers.XMLParser.parse(Unknown Source)
at org.apache.xerces.parsers.AbstractSAXParser.parse(Unknown Source)
at org.apache.xerces.jaxp.SAXParserImpl$JAXPSAXParser.parse(Unknown Source)
at javax.xml.parsers.SAXParser.parse(SAXParser.java:375)
at javax.xml.parsers.SAXParser.parse(SAXParser.java:176)
at com.sap.odp.common.install.dataimport.xml.ImportXmlReader.importObjects(ImportXmlReader.java:141)
at com.sap.odp.common.install.dataimport.xml.ImportXmlReader.parse(ImportXmlReader.java:84)
at com.sap.odp.common.install.dataimport.xml.ImportXmlReader.parse(ImportXmlReader.java:73)
at com.sap.odp.common.install.dataimport.xml.XmlImporter.go(XmlImporter.java:164)
at com.sap.odp.install.actions.ProcessXmlImportFile.executeHook(ProcessXmlImportFile.java:170)
at com.sap.odp.install.actions.InstallAction.execute(InstallAction.java:203)
at com.sap.odp.install.engine.ScriptedImportEngine.runSingleItem(ScriptedImportEngine.java:319)
at com.sap.odp.install.engine.XmlImportEngine.execute(XmlImportEngine.java:128)
at com.sap.odp.install.imports.ImportController$ImportRunner.execute(ImportController.java:302)
at com.sap.odp.install.imports.ImportController$ImportRunner.run(ImportController.java:212)
at java.lang.Thread.run(Thread.java:708)
Let me know if you need additional details.
Regards
Sai

I would like to know is why the light is yellow alert on the Xserve is blinking, I would like to know what are the reasons why do that. Thank you very much beforehand!

I know, because I had never turned on the light in yellow on the back and I see that has the logo warning, then I wonder what it was that or because ocaciono is giving that alert.

Your question belongs in this forum:
https://discussions.apple.com/community/iphone/using_iphone

TS1702 What is the problem why I cannot purchase?

I'm trying to make a purchase and it keeps referring me back to iTunes support

Have you Contacted iTunes Support as requested...
http://www.apple.com/support/itunes/contact.html

Why are all the events in the XML SAX parser not activated?

Hi everyone,
I have written a mini server that parses XML files into SQL queries.
Below is a segment of my code;
 try {
 Class.forName( JDBC_DRIVER );
 myConnection = DriverManager.getConnection( DATABASE_URL, "username", "password");
 EventXMLParser myEXP = new EventXMLParser(directory, myConnection);
 File[] xmlFiles = directory.listFiles();
 for (File xmlFile : xmlFiles) {
 myEXP.XMLtoDB(xmlFile);
 outWriter.println("File:" + xmlFile.getName() + " DONE");
 } catch (SQLException e) {
 System.err.println("SQLException for establishing connection");
 e.printStackTrace();
 } catch (ClassNotFoundException e) {
 System.err.println("CLASS NOT FOUND EXCEPTION HERE");
 e.printStackTrace();
 } catch (Exception e) {
 System.err.println(e);
 e.printStackTrace();
 finally {
 outWriter.println("PARSING COMPLETED");
 outWriter.close();
 }Where the constructor EventXMLParser constructs the following:
 public EventXMLParser(File path, Connection connection) {
 super();
 try {
 this.XMLpath = path;
 this.db_connection = connection;
 this.xr = XMLReaderFactory.createXMLReader();
 this.XMLSAXhandler = new DefaultHandler(); //create a new own handler
 this.xr.setContentHandler(XMLSAXhandler);
 this.xr.setErrorHandler(XMLSAXhandler);
 //System.out.println("DEBUG: db_connection is " + db_connection.toString());
 catch (Exception e) {
 System.out.println("Constructor Error!");
 e.printStackTrace();
 }Below are all my helper methods within EventXMLParser.java
 public void XMLtoDB(String XMLpath) throws Exception {
 try {
 //Input
 System.out.println("XMLpath is : " + XMLpath);
 /*FileReader r = new FileReader(XMLpath); debug
 InputSource in = new InputSource(r);
 xr.parse(in);
 xr.parse(XMLpath);
 /* Note that while parsing, the end of each event, </event>
 * will trigger sendSQL to execute the query on the database
 catch (Exception e) {
 throw new Exception("Error with XMLtoDB!! Exception: " + e);
 public void sendSQL(Event event, Connection sql_connection) throws SQLException {
 //JDBC part
 try {
 System.err.println("DEBUG sendSQL");
 Statement sql_statement = sql_connection.createStatement();
 ResultSet resultSet = sql_statement.executeQuery( event.toSQL() );
 catch (SQLException e) {
 e.printStackTrace();
 /* Parsing XML
 * From here onwards it's all designed for the SAX Parsing with different event calling methods
 public void startDocument() {
 System.err.println("Start Document");
 public void endDocument() {
 System.err.println("End Document");
 public void startElement(String uri, String name, String qName, Attributes atts) {
 CurrentElement= name;
 System.out.println("This is parsing");
 public void characters(char ch[], int start, int length) {
 SimpleDateFormat formatter = new SimpleDateFormat("yyyy-MM-dd hh:mm:ss");
 StringBuffer sb = new StringBuffer();
 for (int i = start; i < start + length; i++)
 sb.append(ch);
 String content = sb.toString();
 if (CurrentElement.equals("eid"))
 temp.setEventID( (Integer.valueOf(content)).intValue() ) ;
 else if (CurrentElement.equals("sd"))
 temp.setShort_description(content);
 else if (CurrentElement.equals("ld"))
 temp.setLong_description(content);
 else if ( (CurrentElement.equals("dt")))
 temp.setDate_Time( formatter.parse(content, new ParsePosition(0)) );
 else if (CurrentElement.equals("repeat"))
 temp.setRepeat_pattern( (Integer.valueOf(content)).intValue() );
 else if (CurrentElement.equals("valid"))
 temp.setValid_period(content);
 else if (CurrentElement.equals("status")) {
 temp.setStatus( (Integer.valueOf(content)).intValue() );
 else {}
 public void endElement(String uri, String name, String qName) {
 System.err.println("DEBUG" + temp.toString()); /*debug*/
 if (name.equals("event")) {
 try {
 /*debug*/ temp.setUserID(1);
 /*debug*/ System.err.println("DEBUG: " + temp.toString());
 sendSQL(temp, db_connection);
 //temp = new Event();
 catch (SQLException e) {
 System.err.println(e);
 }//end catch
 }//end try
Where event is a public class Event {
 //fields
 private int userID = 1; // = 1 only applies for testing
 private int eventID;
 private String short_description;
 private String long_description;
 private Date date_time = null;
 private int repeat_pattern;
 private String valid_period;
 private int status; //1 for new, 0 for modification and -1 for delete
 SimpleDateFormat formatter = new SimpleDateFormat("yyyy-MM-dd hh:mm:ss");
 //Constructors
 //every event requires the following: userID eventID and short_Description
 public Event(int uID, int eID, String shortDescrp) {
 setUserID(uID);
 setEventID(eID);
 setShort_description(shortDescrp);
 public Event(int uid, int eid, String sd,
 String ld, Date d_t, int r_p, String v_p, int s) {
 setUserID(uid);
 setEventID(eid);
 setShort_description(sd);
 setLong_description(ld);
 setDate_Time(d_t);
 setRepeat_pattern(r_p);
 setValid_period(v_p);
 setStatus(s);
 //set
 public void setUserID (int x) { this.userID = x ;}
 public void setEventID (int x) { this.eventID = x ;}
 public void setShort_description (String x) { this.short_description = x ;}
 public void setLong_description (String x) { this.long_description = x ;}
 public void setDate_Time(Date x) { this.date_time = x ;}
 public void setRepeat_pattern (int x) { this.repeat_pattern = x ;}
 public void setValid_period (String x) { this.valid_period = x ;}
 public void setStatus (int x) { this.status = x; }
 //get
 public int getUserID() { return this.userID;}
 public int getEventID() { return this.eventID;}
 public String getShort_description() { return this.short_description;}
 public String getLong_description() { return this.long_description;}
 public Date getDate_Time() { return this.date_time;}
 public int getRepeat_pattern() { return this.repeat_pattern;}
 public String getValid_period() { return this.valid_period;}
 public int getStatus() { return this.status; }
 //Event to SQL statements;
 public String toSQL() {
 StringBuffer sb = new StringBuffer();
 ///if ( status == 1) {
 sb.append( "INSERT INTO events SET" );
 sb.append( " userID = " + userID + ", ");
 sb.append( "eventID = " + eventID + ", " );
 sb.append( "short_description = " + "\'" + short_description + "\'" + ", "); //String
 sb.append( "long_description = " + "\'" + long_description + "\'" + ", "); //String
 sb.append( "date_time = " + "\'" + formatter.format(date_time) + "\'" + ", ");
 sb.append( "repeat_pattern = " + repeat_pattern + ", " );
 sb.append( "valid_period = " + "\'" + valid_period + "\'" ); //String
 sb.append( ";");
 //} else if ( status == 2) {
 System.err.println(sb.toString());
 return sb.toString();
} My question is: I have taken my SQL query generated by toSQL() method in events and it worked.
Here is the funny thing:
Everything is correct syntax wise: No complaints what soever
The mysql part works: Tested separately.
So I tend to think that the problem lies within the SAX parser. I have written SAX2 parsers on this machine before and they have worked too. I tried inserting println statements all over startElement endElement etc etc only to find out that the SAX parser did not call any of the methods that I overided!! Why is that so?
Can you guys spot where my SAX parser fails?

I see.
I try to correct this problem by removing super();
so right now my code looks like this:
 static Event temp = new Event(0, 0, "null", "null", new Date(), 0, "null", 0);
 static String CurrentElement = null;
 static File XMLpath;
 static Connection db_connection;
 static XMLReader xr;
 static DefaultHandler XMLSAXhandler;
 //Constructor, Build the SAX Parser
 public EventXMLParser(File path, Connection connection) {
 try {
 this.XMLpath = path;
 this.db_connection = connection;
 this.xr = XMLReaderFactory.createXMLReader();
 this.XMLSAXhandler = new DefaultHandler(); //create a new own handler
 this.xr.setContentHandler(XMLSAXhandler);
 this.xr.setErrorHandler(XMLSAXhandler);
 //System.out.println("DEBUG: db_connection is " + db_connection.toString());
 catch (Exception e) {
 System.out.println("Constructor Error!");
 e.printStackTrace();
 }This time, I created a new instance of default handler() which can be referenced by as the objects's XMLSAXhandler. However, that did not solve the problem, why does the problem still persist?
Right now, there is only one instance of a default handler created. So why does all my parsing event functions still get ignored?

Why is the thumbnail images placed in different order than the xml?

Hi all!
This same code I have asked about before, and got excelent help, but this is a different problem so I just start a new thread.
This is a code that open a XML file, containing a small list of images, and place them as thumbs on the page.
It kinda work now, but the funny thing is, the order of the thumbs is totally scrambled compared to the xml list, and I can't just see why!
It has something to do whith when the loaders gets transfered via addEventListener to the placePics function, more than that I cant find out!
There may be the better way to put up this code. I just feel putting it up in two nested addEventListeners like this is not the best of practice. But I see no other way here...
package {
 import flash.display.*;
 import flash.events.*;
 import flash.net.*;
 public class thumbHolder extends MovieClip {
 var xmlRequest:URLRequest;
 var xmlLoader:URLLoader;
 var imgData:XML;
 var numberOfChildren:Number;
 var currentImgNum:Number;
 var imgLoader:Loader;
 var imgContainer:Array = [];
 var currentImg:String;
 public function thumbHolder() {
 currentImgNum = 0;
 xmlRequest = new URLRequest("images.xml");
 xmlLoader = new URLLoader(xmlRequest);
 xmlLoader.addEventListener(Event.COMPLETE, handlePics);
 public function handlePics(e:Event):void {
 imgData = new XML(e.target.data);
 numberOfChildren = imgData.*.length();
 for (var i:int = 0 ; i < numberOfChildren ; i++) {
 currentImg = imgData.image[i].imgURL;
 imgLoader = new Loader;
 imgLoader.load(new URLRequest(currentImg));
 imgLoader.contentLoaderInfo.addEventListener(Event.COMPLETE, placePics);
 function placePics(e:Event):void {
 var oldH:Number = e.target.loader.height;
 var oldW:Number = e.target.loader.width;
 e.target.loader.height = 100;
 var prosent:Number = (e.target.loader.height / oldH) * 100;
 e.target.loader.width = (prosent * oldW) /100;
 imgContainer.push(e.target.loader);
 imgContainer[currentImgNum].x = (e.target.loader.width * currentImgNum) + (currentImgNum * 5) + 6;
 addChild(imgContainer[currentImgNum]);
 currentImgNum++;

Never mind! I finally managed to see what to do. Thanks for the help
package {
 import flash.display.*;
 import flash.events.*;
 import flash.net.*;
 public class thumbHolder extends MovieClip {
 var xmlRequest:URLRequest;
 var xmlLoader:URLLoader;
 var imgData:XML;
 var numberOfChildren:Number;
 var currentImgNum:Number;
 var imgLoader:Loader;
 var imgContainer:Array = [];
 var currentImg:String;
 public function thumbHolder() {
 currentImgNum = 0;
 xmlRequest = new URLRequest("images.xml");
 xmlLoader = new URLLoader(xmlRequest);
 xmlLoader.addEventListener(Event.COMPLETE, handlePics);
 public function handlePics(e:Event):void {
 imgData = new XML(e.target.data);
 numberOfChildren = imgData.*.length();
 adToArray(currentImgNum);
 private function adToArray(currNum:Number):void {
 currentImg = imgData.image[currNum].imgURL;
 imgLoader = new Loader;
 imgLoader.load(new URLRequest(currentImg));
 imgLoader.contentLoaderInfo.addEventListener(Event.COMPLETE, placePics);
 function placePics(e:Event):void {
 var oldH:Number = e.target.loader.height;
 var oldW:Number = e.target.loader.width;
 e.target.loader.height = 100;
 var prosent:Number = (e.target.loader.height / oldH) * 100;
 e.target.loader.width = (prosent * oldW) /100;
 imgContainer.push(e.target.loader);
 imgContainer[currentImgNum].x = (e.target.loader.width * currentImgNum) + (currentImgNum * 5) + 6;
 addChild(imgContainer[currentImgNum]);
 if (currentImgNum < numberOfChildren) {
 currentImgNum++;
 adToArray(currentImgNum);

What is the rule for adding application elements to faces-config.xml

I have posed this question before, but was unable to get an answer so here goes again.
What is the rule for adding more than one application element to the faces-config.xml?
The schema documents that 1-n are possible, but why and when should I do this?
--W

sorry if you don't login in tomcat administration before. you must enter login and password of a manager user on tomcat .
The user is the one you give when installing tomcat.
If you have forgotten it : see it to: C:\Program Files\Apache Software Foundation\Tomcat 6.0\conf\tomcat_users.xml
and choose one whop have role='manager'

What is the advent of writing xml mapping for servlet in tomcat4.1

what is the adventage of writing xml mappings for servlet in tomcat4.1? why dont we write in tomcat 3.1?

what is the adventage of writing xml mappings for
servlet in tomcat4.1? why dont we write in tomcat 3.1?Tomcat 3.1 doesn't support it because it was not a common practice then. Tomcat 4.1 deployments were made J2EE compliant. Mapping in XML has an advantage of having a proper DTD for validation, which would be known to all. It serves as a common standard irrespective of the server you use.

What is the most popular reason for importing XML?

Hi
New to this feature, so I would like to know what people are using it for. Presumably the XML is exported from another application. I need to get some idea of which applications people are generally exporting from, and why. Brief examples of workflows would be appreciated.
Many Thanks
Jason

All databases support today export to XML.
For InDesign the items have to be transformed in a special order.
Upon import InDesign can attach a XML element to a specific style or element in the document.
This helps to import a huge amount of informative content in formatted styles. Such methods are used for example for exhibition guides where information comes often very late, but the structure is foreknown or for special medicine the package will be produced automatically upon the content.
XML makes sense when the structure is given but the content may vary. Think about it with catalogues, receipts, phone and address books or similar. Less for literature.
Other methods to get the same result might be InDesign tagged text, which could also be exported from data bases.
Or if someone is exporting IDML it is a package of XML files bundled together, zip compressed with the extension IDML. Here you can research a little bit how XML works with InDesign.

What is the use of XML data collections

Dear all,
I have open the Adventure works database sample and have few technical design question about it :
1- I have seen that seen that some function has been define. IN which case we should use function vs Store procedure ? so far I always have used SP.
2- I have notice also that in some table, there is a field which contains XML content and this XML content is coming from the XML Schema collections. Some shemas has been define here for different tables.
    - What are those shema used for in here ?
    - How they are created ?
    - how they get inserted to Table colum ?
I am not a DBA and knows some basics but not all so thanks for simple explaination :-)
regards

Hi wakefun,
About your questions, I recommend you review the following articles for understanding user function , Store procedure and XML Schema collections in Adventureworks database.
1. Stored Procedures in AdventureWorks;
2.
User-Defined Functions in AdventureWorks;
3. XML Schema Collections (SQL Server).
The XML schema collection is a metadata entity like a table in the database. You can create, modify, and drop them.
the XML stored in a column or variable that a schema is associated with is referred to as typed XML, because the schema provides the necessary data type information for the instance data.
Regards,
Sofiya Li
Sofiya Li
TechNet Community Support

The old calender iOS6, in the year view, it shows how much busy I am in a day by indicating the color intensity. But the new calendar year view is totally useless!!! also too bright!! Why apple does this?? What is the way to revert the calendar back???

The old calender iOS6, in the year view, it shows how much busy I am in a day by indicating the color intensity. But the new calendar year view is totally useless!!! also too bright!! Why apple does this?? What is the way to revert the calendar back???

Unfortunately, that's the way the cookie crumbles nowadays. Sir Jony Ive's GUI design for iOS7 has been met with much skepticism (to say the least). But until the company sees the compelling need for an adjustment or reversal, it "ain't happenin' ". So amble over to the feedback page ( http://www.apple.com/feedback/ ) and make your displeasure known to the company, OR make it known by not purchasing its products. Because as long as the iGadgets continue selling as fast as they can make them, they will see no need for change.
BTW, do note you are NOT talking to Apple here. This is just a user-to-user forum.
Edit: for now, you can also try out any of the alternate calendaring apps available in the App Store.

What is the xml,why it is.....

Similar Messages

Maybe you are looking for