What's the best way to cut annoying mid-range frequencies?

Does anybody know how to eliminate/cut mid-range frequencies that cause the speakers to "buzz"? Hi-cut and low-cut filters don't help much.
Thanks
Anya

hi, anya, how is your cd going?
there are a number of reasons for spiked upper mids.
inferior conversion, inferior monitors, small square rooms, inferior mic/mic-pre.
i heard your original demos when you posted them here, so i'm guessing it's your speakers, as i didn't hear that much wrong with the demo over my monitors.
the region of frequencies you are refering to are what superior gear addresses.
check out the "airwindows plugin' by chrisj. (kagi-airwindows plug-ins)
he has some fee ones which i'm now using a lot.
his commercial ones are well priced.
i have noticed quite a sweetening of the "presence range", which is where your problem is, using his channel and channel eq.
i like his stuff and will buy some more soon.
also try sonalksis' eq, it's very sweet sounding and subtle.
the udder cause of "buzz" could be sub bass overdrive, ie: too much bass that your speakers cannot handle and is making them vibrate. this sort of bass boost does nother for your mix except subtract from its headroom/dynamics.
again, this is due, generally, to using headphones or small bookshelfs to mix on.
best, david r.

Similar Messages

  • What is the best way to extend time capsule range?

    Hello there:
    I was wondering what kind of set up do people have in their house to ensure a good coverage all around the house? I've tried several options and none seems to work correctly. I've tried Time capsule + airport base, I've tried two time capsules, but didn't get too far.
    Thoughts?

    Do you get good coverage all around your house? how big is your house?
    The size of the house is not really the issue nearly as much as the obstructions in the signal path. For example, a wireless signal will easily travel 100 feet with no obstructions slowing down the signal.
    A "typical" wall of sheetrock and 2 x 4s in a home will on average, absorb about 15-20% of the signal. So, with 3-4 walls in the signal path, it is not hard to understand why a signal will likely be much weaker at the other end of the house, or at the point where you add an "extending" device.
    A ceiling is usually about twice the thickness of an average wall or more, so you'll have to take that into account as well if you have multiple stories.
    The "extending" device can only repeat the signal that it receives, so if it gets a weak signal, it "extends" a weak signal.
    The "best" way to extend is connect the two wireless devices using an Ethernet cable, which may not be easy depending on the construction of the home, but it is by far, the "best" way to provide more wireless coverage to remote areas that need it.

  • PE 13: What is the best way to cut out an unwanted segment and leave a fade-out/fade-in overlap?  Without multi-track overlaps?

    I have a long video segment and want to remove unwanted segments and replace them with fade-in/fade-out transitions.  I know that I can do this between two separate video tracks by fading out Video 1 and fading in Video 2 and having the two tracks overlap during the transition.  Is there an easy way to do this on the same track?  The way I've done this before is to cut out the unwanted segment, then move the two segments to separate tracks and overlap them.
    To compound the problem, I have a separate audio track for the wireless microphone I'm wearing. I need to pull that into the fade transitions.  So that's Video 1 and Audio 1 with Narration, all cut at the same time with overlapping fade-out/fade-in in the fewest steps.  Can Premiere Elements 13 handle that?

    billsbayou
    Add On...I am weighing the merits of applying an audio transition directly below the video transition. Considering Crossfade's  Constant Gain or Constant Power with a forced alignment of Between Clips. According to Adobe documentation
    Adobe Premiere Elements Help | Applying transitions to clips
    Adobe Premiere Elements includes two audio transitions in the Crossfade category: Constant Power and Constant Gain. Though both provide fades, they differ slightly. Constant Power creates a smoother-sounding fade, while Constant Gain, though mathematically linear, often sounds abrupt.
    ATR

  • What is the best way to handle input parameter

    When writing sub-vi's, what is the best way to handle input parameter range checking? On the front panel I can choose to have numeric values coerced to be within range, but this does not affect constants or controls wired to the vi when used as a sub-vi. I can build range checking into the vi, but this can result in a cluttered looking vi. Do you have any suggestions.

    As you discovered, the Range and Coercion properties of controls do not work when used in sub-vis.
    Your best option is to go ahead and build your range checking into your sub-vis. If it�s something you will be doing a lot, just make your range checking a sub-vi and drop it where needed. This will keep the clutter to a minimum. You may end up with more than one range checking VI if you need different functionality, but this will still make less clutter and easier re-use.
    Ed
    Ed Dickens - Certified LabVIEW Architect - DISTek Integration, Inc. - NI Certified Alliance Partner
    Using the Abort button to stop your VI is like using a tree to stop your car. It works, but there may be consequences.

  • What is the best way of compressing a large 3 hour final cut file

    What is the best way of compressing a large 3 hour final cut file. I shot the play and it is in final cut and I rndered it so now I have a 22gb file that I need to put on a dvd . Any suggestions
    Thanks
    Macbook Pro
    2.3 GHz Intel Core i7
    with Final Cut Pro 7.0.3
    using Lion as operating system

    Presuming your menus aren't complicated(include audio or video) the total size for the MPG-2 and AC3 files should probably be under 8GB for a dual layer disk. The inspector will tell you the estimated size. 2-pass varible bit rate would be recommended.
    Trying to fit 3 hours on a DVD-5 will only bring very noticable quality hits. Compressor will let you change the average bit rate so that you can fit 174 minutes but trade-off isn't worth it in my opinion.
    Be aware that dual-layer -R and +R media may not play well for everyone everywhere.
    I presume you are not making 1000 or more copies? If you were replication could solve this.
    One other alternative would be to break-up the show into two parts and spread it across two DVD-5s.

  • What is the best way to get a copy of Final Cut 7?  I don't see it on Apple's site anymore and I was told I needed to get ahold of Apple's Pro Divison?

    What's the best way to get a copy of Final Cut 7?

    Amazon.
    Apple stoped selling it officially 20 months ago.

  • What si the best way to export Final Cut Pro X movies to YouTube?

    Hi
    The Share > YouTube tool is proving to be very unrelaible. Often the Share Loader comes back with the "Your password has been rejected" message when I know that the password is correct. It seems to work fine for 50% of the time but it's really frustrating.
    My videos are quite large (given that they are all under two minutes they have been shot in HD and are often over 1Gb - too big for YouTube).
    What is the best way of getting my movies down in size and then uploaded to YouTube?
    Thanks
    Stephen

    Thanks for the advice guys. I'm just rather reluctant to spend more money when FCP is meant to be good at this kind of thing. It's frsutrating thet the YouTube option doesn't work, but it clearly doesn't.
    I think I just need to stop being a scrooge and to buy compressor!
    Cheers
    Stephen

  • What is the best way to import and edit a large amount of footage?

    Hello Apple world,
    As a newbie to Final Cut 10 I have a question regarding best ways to import footage. I'll give you a quick run down.
    I have a 150 gig of gopro footage that I just hit 'import' to recently (from my external HD), it took around 10 hours to process it all.
    Its all under one event, but then somewhat organised into dates etc. But it is very slow. I imported it all at once because it was all footage from the last 6 months of my Whistler/states/fiji trip and want to make a movie out of it, using clips from all over the time, not just in chronological order.
    I have the latest mac book pro, 4 gig ram,2.4 GHz i7, 750 hard drive, with nothing else on the computer.
    Ive read about creating proxy media, after ive imported, but am still somewhat confused as to the benefit. Does it create duplicates? that will fill up my pretty large HD as it is!
    Can you suggest any ways that might make my laptop run a bit faster? Should i delete and work directly from external HD etc etc?
    Any suggestions will be greatly appreciated!
    Thanks in advance
    Harlee

    ascreenwriter wrote:
    Hello,
    I've just finished shooting what I am considering to be my directorial masterpiece.  Shot it on the Canon 5D (1080p, 24fps), and the footage looks amazing.  Now I am ready to start editing and have been using premiere lately, but I have yet to figure out the proper pipeline.  I want to know the best way to retain resolution before I delve into this project.
    My questions:
    1)  What is the best way to start a new project and import the footage without having to render whilst editing, so as to retain all resolution and originality of the source footage?
    2)  What is the best way/ codec/ format to export this same footage once editing is complete so as to retain that crisp 1080p for which the 5D is so recognized?
    3)  What is the best way/ codec/ format to import and export/ render between premiere and after effects?  I am speaking mostly of vfx and color correction.  I also have some 30fps footage that I intend to slow down in AE and then import into premiere.
    I know this is pretty broad, but as a solo filmmaker I really need someone's guidance.  I rarely ever finish my films with the same, crisp look as the footage.  I need pipeline help, and really appreciate it!
    1. Follow the advice above. Also use the Media Browser to import the footage in case you have spanned media files. Import files with the Media Browser.
    2. It largely depends on what you wish to ouput to: Blu-ray, web, etc. This FAQ gives the best answer: What are the best export settings?
    3. Use the Replace with Adobe After Effects Composition function.

  • What's the best way to set up new imac for logic etc?

    In brief:
    Getting new imac (27", 3.4 i7, 8-16GB ram, 1TB HD). Will be using it mainly to run Logic Studio (loads of plugins) and Final Cut Express. I also have 2 external Hard drives one 500G one 1TB.
    The last imac I bought was my first and just went ahead and threw everything at it not really knowing where things should go. This time I want to set things up correctly.
    Basically, with what I've got, what is the best way to set things up. I.e where do I put logic files, samples, BFD2, Amplitube etc. Where do I put videos for use in FCE. Storing projects and backups for use with Time Machine.
    Also noticed the new imac will only have 1 firewire port. I will need to plug in the Hard drives (daisy chained), camera and RME Fireface 800. Was thinking of getting a Thunderbolt Hard drive but they are expensive and hard to find.
    Would really appreciate any help before I get the new machine and start messing things up again.
    Thanks.

    Adding to babowa, enable the system firewall in System Preferences>Security>Firewall tab. Click Advanced and check Stealth Mode.
    Lion is a pretty steady and secure operating system, and as there really aren't MANY Mac viruses, there ARE viruses out there still. OS X is pretty good about letting you know if you do accidently download a virus, and it will help you throw it away if it detects one, such as the MACDefender virus. OS X has built in security features such as sandboxing that doesn't allow viruses in as easily as a Windows PC. As for hackers, as long as you have the firewall enabled and a secure password (for your computer and email accounts), then you should be fine.
    It's the user that lets the virus in, not the computer (unless there's some untold serious vulnerability in OS X, which is highly unlikely). Keep your apps up to date, don't download pirated software, and be street smart on the internet. Don't download things or visit websites that you don't think are real. Safari includes a Phishing feature that automatically detects known phishing sites, protecting you from that big problem. Keep your passwords secure and you should be fine.
    There are antivirus solutions out there, one notable one available in the AppStore is Intego's VirusBarrier (free and plus versions), if you feel you still need one.
    I wouldn't worry about it. Windows users who switch to Mac are always asking these questions.
    Here's some good reading as well
    http://www.apple.com/macosx/what-is/security.html
    Enjoy OS X Lion

  • What is the best way to set up my new Mac Pro?

    Not wanting to screw up in a process I've not done with a brand new machine before, I'm looking for feedback on my plan for setting my new Mac Pro next week...
    The physical plan is this:
    For RAM, I have four 2GB SDRAM's plus the supplied six 1GB modules. My plan here is to install the 2GB rams into the first four slots and install four of the 1GB modules into the remaining four slots for a total of 12GB's.
    When the cost for 4GB modules gets down to reasonable, I'll buy four of them and bump the current rams down the line which will then give me a total of 24 gigs where I'll stay.
    For my hard drives, I'm installing a 160GB Intel X25-M into the first drive bay
    http://www.intel.com/design/flash/nand/mainstream/index.htm
    using one of MaxUpgrades' 'MaxConnects' kits. I will use this drive for the operating system software and my applications and their libraries.
    Next, into the remaining three drive bays, I am installing three 300GB WD Velociraptors. Mine are the pre-'backplane ready' versions:
    http://www.wdc.com/en/products/products.asp?DriveID=459
    so I have bought these sleds for them...
    http://www.maxupgrades.com/istore/index.cfm?fuseaction=product.display&product_i d=180
    I own one of Sonnet's Tempo SATA E4P cards
    http://www.sonnettech.com/product/temposatae4p.html
    which, thanks to this forum, I now understand, with the correct firmware installed, function well so I will install it and be able to establish hardware RAID. I will create a RAID 0 set with the three Velociraptors and use it to store all of my data files.
    Backup will happen on a 1TB WD 'Caviar Black' external drive connected through one of the Sonnet card's external eSATA ports and using the OS 'Time Machine' software.
    And that's the physical plan. My question is about setting things up. The physical installation part is straight forward and I don't expect any difficulties but I'm wondering what is the best way to install the operating system.
    Do I take a first step keeping the supplied hard drive installed, install the solid state drive into the next drive bay and then transfer the contents from the supplied drive onto the SSD or do I do the complete physical installation process and do a 'C' drive start up and install the OS that way?
    And, do you have any tips/suggestions on setting up the RAID 0 set?
    thanks for the help. I want to do this right.
    JQ

    oh mighty Hatter, I knew you'd have helpful guidance to offer! And thank you. You've confirmed my anxieties about the Sonnet card; kind of a 'too much, too quickly' sort of thing. And it's not that Sonnet's not a good company. Just everything to do with new technologies and the growth curve we all, manufacturers and users, go through when they come out. And, for sure, the new Mac Pro's are new technology; the single biggest forward leap in Apple's top-of-the-line machines for some time far as I can tell. Just reading at Intel's website about the Nehalem's is a joy!
    So, I will proceed now with everything except for the controller card, leaving that 'til later. In the meantime, I think I'll just happily run with the four hard drives all running independently. No software RAID. I know just those, the SSD boot drive plus Velociraptor trio's going inside of a 2.66ghz 8-core Nehalem Mac Pro is going to be a working pleasure. Heck, this way, I'll get settled in and used to the machine's speed, have a great time doing so and then, in however many months, I can jump into spending another chunk of money on an excellent RAID card, RAID card's dear Barefeats will have tested and reviewed for us, set up my RAID 0 set and head of to those new races watching my computer leap for joy! Could be that, by then, the cost of Intel 160GB X25-M's will have dropped enough that I can afford to go for a second and have a two SSD RAID 0 boot drive... Yummy!
    Thanks for the help. Like I say, I knew there was useful guidance hanging on some limb within your personal kit, (otherwise referred to as your mind)!
    Interesting to read about the problems people have had with Sonnet's 2.17 update in PPC's... In this computer, my PowerMac G5 dual 2.7ghz, I have a Sonnet 'Tempo Sata X4P' controller card. I downloaded and installed 2.17 and got the same troubles; no cut, no paste, no 'drag and drop' etc. It was miserable.
    Mine, fortunately, magically corrected after running the 'permissions verify and correct' process in Disc Utility and, after a restart, all was back to almost normal but for one exception; the Sonnet card was no longer present or functioning including the four eSATA ports out the back. (I ran Tech Tools Pro 5's repair suites first but, and who knows why, it didn't correct the problem...) This one was absolutely in the 'who knows what the f_'s going on and why it disappeared but did' class.
    Oh, the other remnant is that, when the computer goes into sleep, after about five minutes, the fans rev up, and up, and the computer's frozen; only access is to do a forced shutdown pressing and holding the power button, so I've had to adopt a 'shut down whenever leaving it for more than fifteen minutes' approach to this dear friend. Once I've fully moved into and established my new one (which should arrive today, by the way... Yippeee!!! Can't wait!), I'll do a complete restoration on this one including taking out the Sonnet card. Usually, I sell my old Pro's but, this time, I'm going to keep this one as a back up and just general second computer for times I might need it. It has been such a great and dependable machine. Keeping it seems the right thing to do.
    thanks Hatter. I'll let you know how things go, including what happens with the SSD. I don't have speed test software so I won't be able to track it's performance like that guy in the post you gave me did...
    JQ
    ps- Gotta love that ILLogic fellow eh? Talk about not getting the essence!

  • What is the best way of converting a Top Level VI into a 'sub vi' - or function ( without duplicating programming)

    Hi,
    General question here about design architecture, which i keep running into, but haven't found a really good solution.  If i write a 'Top Level VI' to do something, what is the best way of converting it into a subVI - which is call-able from other VIs, while still allowing the top level VI to have synchronised feedback/indicator updates.
    I guess the point is that when something is a top level VI you write gui logic about what happens when someone clicks buttons or whatever - which you don't want in the 'sub vi' version.
    I did at one point try having a hidden boolean button that was an input to the subVI which would let the VI know if it was supposed to be doing the front panel stuff - or simply running as a subVI.  This isn't really ideal though - since it would be better to be able to hive off the grizzly useful stuff from the fluffy - front panel updating stuff - having them together makes the VIs rather untidy.  More annoyingly though, if you have the front panel version of it running - say waiting for you to hit 'go', it breaks all the other VIs that use it as a sub vi - since they can't compile when a sub vi is already running.
    Another possibility that i tried was to basically duplicate the vi so that there was a backend part, and a front end part - and when i click 'go' the backend part is called as a sub vi.  The problem with this is that it really limits the interface that the user gets - since none of the controls on the front panel update with the results untill the sub vi is over.  I guess again i could solve this by passing references to some of the controls to update them in the subvi - but this doesn't really seem like the ideal situation if the subvi is called by something else without the same types of controls etc.
    One final idea i had was to essentially paste all the controls in the VI into a global variable file, and make the sub vi update them, and the front panel VI read from them.  This seems to 'work' - although clearly it is a work around rather than a proper solution - since i spend loads of time worrying about how i update cluster variables in the global - reading and writing.
    Does anyone have any guidance on what they do to solve this problem?
    JP

    You could run a subvis in a Subpanel on your top level.  Lets you see the current data while the subvi is running.
    --Using LV8.2, 8.6, 2009, 2012--

  • What is the best way to import pictures from Lightroom 5 into FCP X

    What is the  best way to transfer pictures from Lightroom 5 into Final Cut Pro X?

    There is no one best way.  If, for instance, you want to be able to zoom into the picture with a Ken Burns effect then you may want to save out a very high res version that will be larger than your video resolution. Just use Lightroom to export a jpg file wherever you want it. You could export it into the Events folder and then choose not to copy it when you import it within FCPx. You could import the picture into iPhoto and then access it directly from within FCPx. Those are two simple, "regular" ways to get it into FCPx but if you are not going to Ken Burns the image by zooming into it and such you will want to crop it in Lightroom to the same size you will be using ie if you are making 720HD video then crop the image to that size and proportion before you export it from Lightroom.

  • What is the best way to work with mixed media in 1080 timeline?

    Hi there,
    I have a project shot mostly in 1080 24p but a bit of 720 24p and 4x3 30p footage.
    What is the best way to work with this mixed media?
    Thanks!
    Steven

    Hi Shane,
    Ok just to recap (thanks for being patient by the way)...I have put some questions in here...feel free to write in caps to respond and we'll put this baby to rest!
    1) I will work in a 1080p FCP sequence, correct?
    2) HD 1080p footage captured as applepro res hq I will leave as is and work with?
    3) HD 720p footage which was captured as applepro res hq. Can I just drop in 1080 timeline and let FCP do its work? Or should i run through compressor, if so what setting shall I submit it too?
    4) I dont have a budget for an external hardware to convert SD to HD...should I capture my SD Beta through Final Cut and just leave and let FCP do its work? Or should I run through compressor? If so what setting shall I submit it too?
    5) For for my master sequence in FCP am I not using an I-Frame format apple pro res if I am using my apple pro res hq 1080 footage as my formatted sequence? I am not sure what you mean by GOP?
    6) I also found some 60p footage 1080p XDCAM compressor shot with the same XDCAM camera. I put in the 1080p 24p timeline but it was pretty choppy...any ideas of this conform?
    Thanks very much for all your help it has gone along way,
    Steven
    Saying what CODECS you are working with was my question. 1080, 720, 4:3...really says nothing. There are a dozen 1080 codecs, another dozen 720 codecs, and nearly 100 4:3 formats.
    Best to capture all the footage to one uniform codec.
    Second best is to work with one format and let FCP conform the rest to that...IF and only IF that format is an I-Frame format like ProRes. GOP formats as master sequence formats cause TONS of issues.
    What I'd do is work 1080 ProRes, just add the 720p footage (Use Compressor to convert it if you didn't have a lot, but if you had a lot, just add it), but I'd capture all the SD 4:3 footage via a Kona 3 or Matrox MXO2 as 1080 ProRes. Hardware conversion of SD to HD is much better than anything FCP can do. AE might do good as well. But then use Compressor to convert 29.97 footage captured (you can't convert 29.97 to 23.98 when you capture) to get to 23.98.

  • What is the best way to Burn a DVD Movie

    What is the best way to Burn a DVD Movie, do I need a specific program?

    pamelafrommelbourne wrote:
    What is the best way to Burn a DVD Movie, do I need a specific program?
    If  you're trying to copy a commercial movie and burn it to disc, then it is expressly against the Terms of Use of this community to describe any method to illegally copy or circumvent copy protection DVD's
    If you've made a movie and want to author a DVD, then you should use iDVD, Toast or, if  you're really skilled, Final Cut Pro X. 
    If you just want to move a movie to a DVD, which probably won't play on a DVD player, then just insert a blank DVD, and move it over from the finder.  Click burn.

  • I have two videos and I would like to use parts of both videos with one audio track what is the best way to edit this?, I have two videos and I would like to use parts of both videos with one audio track what is the best way to edit this?

    In Final Cut Express I have two videos I'd like to merge parts of each video into a final film.  What is the best way to do this in FCE?

    Hi
    I use a slightly different way than Alchroma.
    Same
    • One video on track 1 and the other on Video.track 2
    • Resize to 25% and move one to the left and the other to the right
    Diff
    • I don't use the blade tool
    • I use the Pen tool and change the transparency - then I get fast or slow transitions in same stroke and easy to fine-tune later if needed. (But this can be done with the Roll-tool if Blade is used - so it might be as easy)
    Final
    • Resize to 100% and Center
    Video is done
    Audio - very close to this by changing the level so that best audio will dominate
    • Pen tool here too
    But that's me - the Alchroma way is as good as this or may be better for some
    Yours Bengt W

Maybe you are looking for