Wicd Doesn't Show Networks

Question

I just installed wicd, had it working and everything, and then after I restarted X and wicd, it said I wasn't connected. The internet still worked, though; firefox was fine and I was torrenting at about 60 Kbps. Then, after a reboot, the whole thing went. Also, hal failed during the boot process, but I don't see why -- the only changes I made to DAEMONS was adding wicd and removing networkmanager/dhcpdbd, as per the wiki. Here's my rc.conf:
# /etc/rc.conf - Main Configuration for Arch Linux
# LOCALIZATION
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime"
# USEDIRECTISA: use direct I/O requests instead of /dev/rtc for hwclock
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
LOCALE="en_US.utf8"
HARDWARECLOCK="UTC"
USEDIRECTISA="no"
TIMEZONE="America/Chicago"
KEYMAP="us"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"
# HARDWARE
# MOD_AUTOLOAD: Allow autoloading of modules at boot and when needed
# MOD_BLACKLIST: Prevent udev from loading these modules
# MODULES: Modules to load at boot-up. Prefix with a ! to blacklist.
# NOTE: Use of 'MOD_BLACKLIST' is deprecated. Please use ! in the MODULES array.
MOD_AUTOLOAD="yes"
#MOD_BLACKLIST=() #deprecated
#MODULES=(snd_pcsp)
MODULES=(fglrx !pcspeaker !snd_pcsp)
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
# NETWORKING
# HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
HOSTNAME="Bender"
# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available interfaces.
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
# - prefix an entry in INTERFACES with a ! to disable it
# - no hyphens in your interface names - Bash doesn't like it
# DHCP: Set your interface to "dhcp" (eth0="dhcp")
# Wireless: See network profiles below
#eth0="eth0 192.168.0.2 netmask 255.255.255.0 broadcast 192.168.0.255"
eth0="dhcp"
wlan0="dhcp"
INTERFACES=(lo !eth0 !wlan0)
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# - prefix an entry in ROUTES with a ! to disable it
gateway="default gw 192.168.0.1"
#ROUTES=(!gateway)
ROUTES=(gateway)
# Enable these network profiles at boot-up. These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up (dialog package required)
# - prefix an entry with a ! to disable it
# Network profiles are found in /etc/network.d
# This now requires the netcfg package
#NETWORKS=(main)
# DAEMONS
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
DAEMONS=(@syslog-ng pulseaudio hal !network !dhcdbd !networkmanager wicd netfs @crond alsa @openntpd)
#DAEMONS=(@syslog-ng !network pulseaudio hal dhcdbd networkmanager netfs @crond alsa @openntpd)
#DAEMONS=(syslog-ng network netfs crond)
Edit: I should also mention that, not only is wicd not connecting, but also that no networks are showing up.
Last edited by Buce (2009-03-20 07:29:50)

Answer 1

Figured it out. For anyone else switching from networkmanager to wicd, make you don't uninstall wireless_tools when you remove networkmanager (or reinstall it if you do).