Will I be able to use my printer which is not wireless with the airport express and will it become a wireless printer ?

I have a wired printer and I need to know will the airport express work with this printer and will I be able to print wirelessly from my IPad ?

Can't print from iPad unless it's AirPrint able...
If it isn't you may want to check out Printopia.

Similar Messages

  • I downloaded CS6 and am having issues with my print driver. It is not compatible with the HP 2600n and have tried to download drivers given to me by adobe ( (Jupiter 3) but it is not working. after a few days. Its a temporary fix and is still looking for

    I downloaded CS6 and am having issues with my print driver. It is not compatible with the HP 2600n and have tried to download drivers given to me by adobe ( (Jupiter 3) but it is not working. after a few days. Its a temporary fix and is still looking for the HP driver when i boot up. It also will not save in any print or postscript format. Does anyone know how to fix?
    Currently use a Mac with the latest Mavericks 10.9.4

        Oh boy! Acting kind of weird seems to be an understatement, aquaequus!
    What type of troubleshooting were we able to do with you? I want to make sure that we can get some sort of resolution for this problem.
    It is quite possible the battery door may get your phone in working order again. I'm not sure if the store has it in stock, but it is available in our warehouse for $14.99 which can be ordered via customer service.
    Tamara H.
    Follow us on Twitter @VZWSupport

  • I have an Airport Express connected via optical toslink to a dac/amp in turn connected to speakers. When using iTunes I get message "no speakers connected to Airport Express" and audio sound has drop outs.

    I have an Airport Express connected via optical toslink to a dac/amp in turn connected to speakers. When using iTunes I get message "no speakers connected to Airport Express" and audio sound has drop outs.

    Ok, if you are connecting the AirPort Express Base Station (AX) to the existing wireless network, then the DSL in the next room is most likely a combination DSL modem and wireless router. Thanks for clarifying that for me.
    Although they may only be separated by a single wall, the building material used in that wall may be enough to prevent the AX from receving a "good" signal from the DSL router.
    Since I don't know what computing equipment you have available, please check out this AirPort User Tip: AirPort - Optimal Base Station Placement to see if you can get some SNR measurements at the location of your AX. To do this properly, you will want to power-off the AX and only get these measurements for the DSL router.

  • When our iPad is in use on the internet, my iMac internet connection goes off. I can't get the two devices to work at the same time with the AirPort Express. Is there a setting somewhere I may have missed?

    When our iPad is in use on the internet, my iMac internet connection goes off. I can't get the two devices to work at the same time with the AirPort Express. Is there a setting somewhere I may have missed?

    When two or more devices conflict it typically means that the DHCP service is either misconfigured or is not running at all. DHCP provides IP addresses to local network clients.
    Is your AirPort Express base station the only router in your current network configuration? That is, is it connected directly to an Internet modem and not to another router upstream of it?

  • Printing problem with Macbook, Airport Express and new Canon IP4600

    Just set up new printer, a Canon ip4600. Adding printer in System Preferences to my flat-screen iMac, I got it working using the Airport Express. But trying the same thing with the Macbook (2.4 GHz Intel), can't get it to print. (Both worked fine with previous Epson printer.) I fear it's a network issue, not sure what to do. Any suggestions will be appreciated.

    For each of the AirPort Express Base Stations (AX), did you also change the "iTunes Speaker Name" on the Music tab when using the AirPort Admin Utility? Is this the name you're referring to from iTunes?

  • HT4623 My iphone will no longer sync with my Mac with Lion operating system which does not interface with the cloud. How do I sync by plugging in?

    I have always been able to sync by plugging into my computer Mac OS 10.6.8 which does not interface with icloud. Now my iphone only wants to sync calander and contacts via icloud and will not sync when plugged in. Does any one else have this issue and or ideas?

    Do you have the latest version of iTunes?  If not, get it at:
    http://www.apple.com/itunes

  • I was told at the Apple store that I could simply plug in ( electric power) the Airport Express and it would find my wireless network. I hoped to use it as a way to play music from my iphone. I do not use other Apple routers etc,

    The Airport Express is not finding my wireless network. I do not have any of the devices listed below. I have a Belkin wireless router. Can I still use Airport Express ( without plugging an ethernet cable into it) ? Any ideas for how to make it find my network ? It is sitting next to the wireless router-so is in range.
    If you already have a wireless network in your home and want to extend its range, AirPort Express can help. Just place it in range of your primary base station — an AirPort Extreme, Time Capsule, or another AirPort Express — and near the area where you want your wireless connection. Launch the easy-to-use AirPort Utility app on your iOS device or Mac, and you’re mere minutes away from long-range Wi-Fi enjoyment.

    Hi - you can do what you want to do with AirPlay from your iPhone - but unfortunately it is not as easy as the people in the Apple store told you - your first problem is that you have a non Apple router - you cannot extend a non Apple router wirelessly with the Express - you can only join the network and connect an ethernet device to it - you can however connect via ethernet and have it create a wireless network of its' own - you can set this up from your iPhone or the XP - but this is a complicated setup and would involve many different discussion areas of this forum - therefore I would suggest that you use your 90 days of support and consult directly with Apple to do this - go to this link - http://www.apple.com/support/contact/

  • Current version of airport utility will not connect with older airport express

    I was given an older aiport express that I want to add to my network for iTunes sharing.  I have an airport express and aiport extreme currently.  I am running Mac OS x 10.7.5.  My current version of airport utility does not support this express and it tells me to download utility version 5.6. When i try to install version 5.6 i get an error message that tells me to contact software manufacturer.  I'm sure there is a simple fix but I don't know what to do.  Any help would be great!

    Hi
    again , at least for getting 5.6 installed, look at my post earlier, or better to JEFFY's and download an much better alternative "unpkg", to get it ( 5.6) on to  your  mac.
    Then, though, getting to use it to configure your older AP as I attempted is anothe matter. I didn't succed so far..
    Good luck to you. If it works pse tell .
    Thanks.
    Pierre

  • Itunes will not connect with my airport express

    My new macbook will connect automatically to my airport express network with airtunes but the itunes on my imac will not. It show the network as an option for additional speakers but when I choose the airport express network as my external speakers it gives me a box saying it is connecting then after a few minutes it just goes away and reverts to the computer for my speakers. Any ideas on what to do? The aiport express has the latest firmware update.

    Check the Firewall settings in the Sharing area of System Preferences.
    I think you need to have iTunes Music Sharing enabled (maybe not).
    Ian

  • TS3408 I am unable to use Safari because the web pages fail to load or does not load graphics.  I am not pleased with the current Safari and will now have to use a secondary browser.

    My issues is with multiple websites.  Buttons do not work, pages do not load completly or the graphics are not visible.  I need to use another browser such as FIrefox or Chrome.

    Please read this whole message before doing anything.
    This procedure is a test, not a solution. Don’t be disappointed when you find that nothing has changed after you complete it.
    Step 1
    The purpose of this step is to determine whether the problem is localized to your user account.
    Enable guest logins* and log in as Guest. Don't use the Safari-only “Guest User” login created by “Find My Mac.”
    While logged in as Guest, you won’t have access to any of your personal files or settings. Applications will behave as if you were running them for the first time. Don’t be alarmed by this; it’s normal. If you need any passwords or other personal data in order to complete the test, memorize, print, or write them down before you begin.
    Test while logged in as Guest. Same problem?
    After testing, log out of the guest account and, in your own account, disable it if you wish. Any files you created in the guest account will be deleted automatically when you log out of it.
    *Note: If you’ve activated “Find My Mac” or FileVault, then you can’t enable the Guest account. The “Guest User” login created by “Find My Mac” is not the same. Create a new account in which to test, and delete it, including its home folder, after testing.
    Step 2
    The purpose of this step is to determine whether the problem is caused by third-party system modifications that load automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
    Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you boot, and again when you log in.
    Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Ask for further instructions.
    Safe mode is much slower to boot and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal boot may also be somewhat slow.
    The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    Test while in safe mode. Same problem?
    After testing, reboot as usual (not in safe mode) and verify that you still have the problem. Post the results of Steps 1 and 2.

  • I want to create a network so that I can share a printer, but I don't want to connect it to the internet. It is just for the laptops to connect to the printer. Is that possible with the airport express?

    I think I should be able to, but both at the apple store and when I called apple, the sales people told me it can't be done.
    I've read the manuals for both the express and the extreme, and I can't see why this is not possible.
    Can anyone enlighten me on this?

    Yes, this is possible ... but understand that you would need two switch wireless networks between network/Internet access and for printing.
    The AirPort would not get a Public IP address, but it would have a Private IP address of 10.0.1.1 ... and it would be providing wireless clients connected to it with Private IP addresses in the 10.0.1.2 - 10.0.1.200 range.
    AirPort Utility > Select the AirPort > Manual Setup > AirPort > Wireless
    Wireless Mode: Create a wireless network
    Wireless Network Name: <enter a desired Network Name or SSID>
    Radio Mode: <leave the default or select a desired radio mode>
    Channel: Automatic
    Wireless Security: <select the desired wireless security type>
    Internet > Internet Connection
    Connect Using: Ethernet
    Connection Sharing: Distribute a range of IP addresses
    Internet > TCP/IP
    Configure IPv4: Manually
    IP Address: 10.0.1.1
    Subnet Mask: 255.255.255.0
    Router Address: 10.0.1.1
    DNS Server(s): <leave blank>
    Domain Name: <leave blank>
    Internet > DHCP
    DHCP Beginning Address: <leave default or change to a desired starting address>
    DHCP Ending Address: <leave default or change to a desired ending address>
    Advanced > Logging & Statistics
    Allow SNMP (unchecked)
    The AirPort will still report at least three errors: 1) Configuration of WAN, 2) SNMP over WAN, and 3) Double NAT. These can all be safely ignored to stop the AirPort's status light from flashing amber in this configuration.

  • Using Captivate 3 which is not compatible with Flash 10, need 9

    When using Captivate 3 with full motion tracking, if using Flash 10 we get a blank screen. I've been told I need to install Flash 9 so it will work. However, I can't find a way to download Flash 9 anywhere. Any suggestions?

    ios 6 requires itunes 10.6.3 or higher which requires Mac OS 10.6.8 or higher

  • Using iMovie '08 on an iMac G5 with the new Canon and Panasonic cameras???

    Once you get an HD component, you want to rapidly upgrade the rest of your system to HD. My question- which of the recently announced Panasonic and Canon cameras with 1080i or 1080p(24) can I use with iMovie 08 on an iMacG5? Do these new flash-based cameras have any ability to support nonAVCHD which isn't good for sports.

    I have had good results recording football games in AVCHD, but you may not consider it acceptable.
    A G5 is on the lower borderline of acceptable hardware for iMovie 08, so you should expect long importing and processing times.
    AVCHD in iMovie requires an intel processor for importing. There may be a workaround by using third party software called "Voltaic". Do a search on these forums to find posts from people who use this.
    Here is a sample of a AVCHD movie of a football game recorded on a Panasonic HDC-SD5 using 1920x1080. This version is in the medium setting for WebGallery.
    http://gallery.mac.com/htimjohnson#100343

  • Compatibility Issue(s): Airport Express and HP Officejet 8500 Pro. How to enable network-printing?

    Hello there,
    I recently bought a Macbookl pro and now wanted to connect my Denon S 302 and my printer to my wireless network. Since the Denon S 302 cannot connect to my mac (since it's fireware is to old, so there are combatibility issues as well), I bought a "Airport Express station". The station has been configurated as a seperate wireless network, the stereo device (my Denon) and the HP Officejet were also connected. The stereo device with it's optical plug, the printer first over USB and then over ethernet conncetion.
    The setup was quite easy, the stereo device is also working with my iTunes libary, so the connection from Mac to Airport Express is not the problem.
    Also the printer is working correct, when it's plugged in my Mac... Both connection ways, the USB and Ethernet connection were not working, the printer cannot be activated it's status is offline.
    Also the Manual does not really help.
    The prouble shooting here linked a document to the HP site, which states, that my printer will not work with the airport express station, so is this ture???
    Unfortunatly the warranty is exeeded, so there are no possibilities to connect the HP support via Mail or ask any questions..
    Thanks for any help and advice in this case...

    There is another problem:
    The printer is recognized in the router setup, so it should work, but since I'm now using a Mac instead of my old Laptop, the router cannot forward the printer to my Mac, this only works with Windows PC's ... 
    I could post a link to the official help board of my telephone provider (the distributor of my router), but since this post is in german, it might not really help. But what was said, that it could work, if Apple would help them to get the right settings...
    Now I'm trying again to connect the printer to the Airport Express, which is now connected to the existing wireless network, instead of building a new one...
    So, are there any more possible solutions?
    And thanks in forward for all your help...
    Greetings from Germany

  • Help - Receive message "an error occurred printing this document" when using airport express and Ipad

    Hi, I am trying to set up an airport express hub to work with a Star tsp100 receipt printer and IPad 2. The IPad is being used to accept credit card payments and I was hoping to print receipts out wirelessly using the airport express and receipt printer. I checked to make sure the airport express has the latest firmware and it does. The IPad software is also updated to the latest 7.1.  I then connected the Airport express and IPad and the network setup with no problems. I connected the receipt printer to the airport express using the USB slot available. While the printer comes up as available, when I attempt to print something, I get the error message "An error occurred printing this document" and I can cancel or Try again. No matter how many times I try, I continue to get this message and I lost as to the cause. When I disconnect and reconnect, another instance of the printer appears, but receive the same cryptic error message when I try to print. Totally lost, please help

    Hi kelston3,
    In order to print from an iPad you will need to use a printer that is compatible with AirPrint, which is described in the following article -
    About AirPrint
    http://support.apple.com/kb/HT4356
    AirPrint printers must be wireless on your network - not connected via USB to the base station. There is a list of printers that are known to be compatible with AirPrint in the article.
    Thanks for using Apple Support Communities.
    Best,
    Brett L

Maybe you are looking for

  • Displaying MS Word File in browser

    Hello, Can anyone pls tell about the method to display MS word file present in a folder in my site on the browser. I dont want it to give it as download dialog box. Thanks Sharath

  • Error 0xE8000084

    I just downloaded iOS 7 today and after the download, I was having trouble connecting my iPhone 5 to iTunes. My phone does not show up in iTunes even though it is plugged in and I repeatedly get the error code 0xE8000084. I have Windows 8 and I have

  • How to put documents in portal

    Dear Friends, I have an issue like, our client having some help documents, that they want to put in portal through worksets (role base access). help me Regards Suresh

  • Maitain text in diff languages

    Hi,         i want to maintain the user given text into diff languages in database table. ( like FR, IT, ES, DE, NL, PT) and also maintain the EN language in another database table. This is the my requirement ( this is not depends on the user log on

  • Iphoto library files show 'unsupported format'

    I can't see some of the files in aperture_3 that were imported originally from iPhoto - I get this message: The file index.xml.gz could not be found. It may have been moved, renamed, or deleted. Would you like to locate it? When i try to relocate the