Wireless controler issue

Cisco 5508
Once a guest connects to wireless lan, they are displayed a "disclaimer" and then the session should run for 3 hours without seeing the disclaimer.
If the session disconnects before 3 hours and re connects, they are presented with the dicslaimer again , and they shouldnt be.
Would you be able to confirm if my understanding is correct?
Please advise.
Thanks.
Albert

Just for info:
A. The ARP Timeout is used to delete ARP entries on the WLC for the devices learned from the network.
The User Idle Timeout: When a user is idle without any communication with the LAP for the amount of time set as User Idle Timeout, the client is deauthenticated by the WLC. The client has to reauthenticate and reassociate to the WLC. It is used in situations where a client can drop out from its associated LAP without notifying the LAP. This can occur if the battery goes dead on the client or the client associates move away.
Note: In order to access ARP and User Idle Timeout on the WLC GUI , go to the Controller menu. Choose General from the left-hand side to find the ARP and User Idle Timeout fields.
The Session Timeout is the maximum time for a client session with the WLC. After this time, WLC de-authenticates the client, and the client goes through the whole authentication (re-authentication) process again. This is a part of a security precaution to rotate the encryption keys. If you use an Extensible Authentication Protocol (EAP) method with key management, the rekeying occurs at every regular interval in order to derive a new encryption key. Without key management, this timeout value is the time that wireless clients need to do a full reauthentication. The session timeout is specific to the WLAN. This parameter can be accessed from the WLANs > Edit menu.
@ http://www.cisco.com/en/US/products/ps6366/products_qanda_item09186a00808b4c61.shtml

Similar Messages

Xbox 360 Wireless Control not working in W7 x64

Hey all,
I have read some topics in here about issues on a Xbox 360 Wireless Control connection in Windows 7 x64 (I'm on a Dell Inspiron n5110, 6gb ram, intel core i5). Thing is, in difference to all those threads, in my devices list there ain't any "unrecognized
devices" nor anything, so all the solutions listed don't work for me.
What I have done:
1) Installed the Accesories 1.2 for Windows 7 x64
2) Plugged the receiver to my usb (it got detected by windows, recognized and listed properly in the devices and printers, as a wireless receiver)
3) Turned the controller on, hitted the sync button on the receiver, then on the control... and I get a eternal green blink around the Xbox button, which never ends nor stays in one of the quadrants.
As I don't see nothing like "unidentified device" in the device admin, I simply can't use the "update drivers" stuff. What can I do, what am I doing wrong?
Thanks in advance...

Hi,
I would suggest you to follow these steps and check if the issue is resolved:
1. Verify that the accessory is an officially licensed Xbox 360 wireless accessory.
2. Examine or replace the batteries to make sure that you have fully charged the batteries in the Xbox 360 wireless accessory.
3. Move the receiver away from other devices that could interfere with the wireless communication between the receiver and the Xbox 360 wireless accessory.
Note: Devices such as wireless routers, cordless telephones, and microwave ovens can generate wireless interference.
4. If you are using a wireless keyboard or mouse, disconnect the keyboard or mouse and reconnect the the wireless gaming receiver. Then try reconnecting your Xbox 360 wireless device to the PC.
Also, you may try uninstalling and reinstalling the drivers for controller in device manager and check if this helps.
If the problem persists, then please contact Xbox support for further assistance. Here’s the link:
http://www.xbox.com/en-GB/support/xbox360/
Please Note: Since the site is not hosted by Microsoft, the link may change without notice. Microsoft does not guarantee the accuracy of this information.
Hope it helps.
Regards,
Blair Deng
Blair Deng
TechNet Community Support

Pavilion wireless keyboard issues

I have just bought a new Pavilion 500-250ea desktop + Pavilion 22xi monitor. Nice hardware, shame about having to have Windows 8.1 though :-)
The desktop shipped with a wireless mouse and a wireless keyboard (Part No 697345-031). I've spent the last couple of days with all the kit on the desk, setting everything up and transferring all my files etc. All going nicely until I got to the stage where I was able to take my old machine away and put the new one in the space UNDER the desk (wooden top). Now the mouse is erratic and the keyboard often just 'hangs' for a while. Surely the wireless range ought to be better than that and not bothered simply by an intervening desk???? Or is 'deskTOP' meant to be taken literally.....
Also, the keyboard has NO CapsLock or NumLock lights !!! This plays havoc when trying to enter passwords :-( Is there any utility perhaps to display the CapsLock and/or NumLock status on the screen??

Hello Nemo2000,
I have read your post on how your desktop is experiencing erratic control of the wireless keyboard and the mouse with the desktop hidden away, and I would be happy to assist you!
To begin, I recommend moving the desktop to a more open area to test for spacial interference. To expand on this, I suggest following this document on Wireless Printing Common Questions. Under "Wireless Connection Issues" please select "How do I improve a weak signal from my wireless router?" on obstructions.
In regards to the caps and num lock keys, I understand there are no indication lights in the top right-hand corner. On most programs, however, you will be given an indication that the cap locks are on for passwords. A good example of this is when you log onto your computer, it will tell you if the caps lock is on or not.
Please re-post with the results of your troubleshooting, and I look forward to your reply!
Regards
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

Wireless Control System Error Msgs.

Hi,
I have a problem with Wireless Control System (WCS v7) WCS-STANDARD-K9 and installed with WCS-PLUS-100 (installed two licenses) so total licensed installed is for 200 Acesspoint's in WCS. I have 149 AP's connected to WCS and its shows error " System is in voilation of license. The number of APs (149) registered is greater than licensed (0). Please go to the license center under the Administation Menu to add additional WCS licenses.
What would be the reason for this error,? Thanks

If you go to the license center in WCS, do you see a total of 200 AP support. You need to make sure you have a base license before you add additional plus license. I had an issue before, where I added a whole bunch of plus license after I installed a 250 base. I had 400+ APs and ran into the same issue but I had 250 base. Well I forgot to add the other 250 base so I had to remove all the plus license before I could add the other 250 base. Then I had to add all those plus license after that. The license center will tell you exactly how many APs it will support. From what you posted, it looks like you have 0.
Sent from Cisco Technical Support iPhone App

Wireless control light on G780 still on

Hi,
I have a minor problem with my G780 laptop machine, the wireless control light is always on, even after switching off all the Broadcom wireless card and the Bluetooth module in the Control Panel (Windows 8 64-bit).
I just updated the Broadcom card driver, did not help.
The problem is not critical, everything still works, but it's annoying.
Doeas someone know the solution to this?
Thanks,
Christopher

hi KBoniecki
Welcome to the Lenovo Forums.
When you said "the wireless control light", you probably mean the wireless status indicator light.
- Link to picture
I haven't tried this on the G780 but for the G580 (which is a similar model), you can turn off the lights by doing either one of the following:
1. Press the Windows key‌ +R, type diskmgmt.msc and press Enter. On the Device Mananager, navigate to Network Adapters then right click on your wireless card (eg. Broadcom 802.11n Network Adapter) and hit Disable.
2, Boot into the BIOS by tapping F2 on boot up then disable the Wireless LAN Support on the Conguration Tab.
- Link to picture
Give it a shot.
Regards
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Is there a fix for the MBP wireless dropping issue?

I began to experience the Macbook Pro dropping wireless connectivity on my very 1st Apple in 2008. At the end of the day my machine was replaced with a new Macbook Pro mid 2010. It appeared to be working just fine until about 2-3 months ago when I started dropping my wireless printer connection. I searched the internet hoping for a driver update from HP or something from Apple and each time I found something, the problem still existed. I even thought that by upgrading to Lion would resolve any issues that I have with my MBP wireless connectivity issue. After upgrading to buying a new router, new printer and upgrading to Lion; the wireless dropping issue still remains unresolved! I know there are several hundred in not thousands of people who are having the same problem so what are we supposed to do?
When my 1st MBP was replaced in 2010 I had to stop working because I was diagnosed with "Failed Back Surgical Syndrome" and was in the process of applying for disability. Something in the back of my mind said that I needed to purchase Apple Care for this new replacement however I had used all of my savings & retirement to sustain life for me and my family that there was nothing for Apple Care. If it weren't for my church and family I am not sure what I would do during the 18 months of no income while waiting for a decision only to receive an appeal until I findly stood in front of an Administrative Law Judge who heard my case and granted me disability. Besides there was no way I could ask anyone for money to purchase a warranty for a top of the line laptop while the country was falling off an economical cliff.
I broke down and called Apple Support and was told that I qualified for technical assistance regarding the upgrade to Lion a few weeks ago. The tech on the phone had me run some disk utility tests and had me repair permissions which she said could be the cause of the problem. I willingly went along with her in hopes that this was indeed the fix. However, within 10 minutes of hanging up the phone my MBP began to drop it's wireless connection to my new HP printer and also the Internet. Hence my question above is what I am really looking to have answered! What is the fix to this problem that so many people are having issues with? I couldn't afford to purchase Apple Care back in 2010 and I can't afford to purchase a new 2011 machine today if that truly is the fix!
I will be disabled for the remainder of my life and I have grown dependent upon my computer to stay in touch with friends and colleges from work. I worked for the IT Group at Wynn Resorts and I can say that the type of service Appple is providing it's customers is not what I learned over the past 25 years with Mr. Wynn. Why can't Apple get the simple concept that it's customers are it's life line and keeps them in business. I need help and I don't know what to do nor where to turn. It would be different if Apple acknowledged the issue and said they were working on it however they aren't. I plead to Apple to help me fix my notebook so I can stay connected to the outside world vs. couped up inside my home.
Best Regards,
Scott Leavitt

I am simply lookig for some help not an argument. I am not an RF specialist however have setup a few wireless networks in my tenure at Wynn Resorts. I fully agree that wireless networking is an art and a science however the powers that be in Network Land have toughted wireless networking is the easiest and quickest way to get two computers to talk with one another. As I previously said I have already turned one (1) MBP in for this problem and Apple decided to replace it because they could not fix the problem with my particular MBP. This MBP was running Leopard when the problems started
I am having a hard time believeing that there are several other devicces in my home that depend on a wireless network to operate and my MBP is the only one having an issue. I took this a step further and decided to see what would happen if I tried to connect wirelessly via Fusion. In Windows 7 I am able to print and scan to my hearts content without any issues. I am able to browse the internet as much as I want. I close Fusion and try to connect to my printer via wireless and nothing.
In order to get Apple to help do I need to get a Network Analyzer and capture packets when I have these problems? Out of the 1000 + posts is there a consolidation of which answer is the best? BTW I am accessing the internet via a wireless connection using Fusion and Windows 7.
In response to Linc's comments, I will look at the router specifications however I did not qualify that these devices are not using the wireless connection at the same time. Right now I would guess there are maybe two (2) or three (3) at the most that are actively transmitting / receiving information. -- Thanks

Cisco wireless control system

we are using cisco wireless control system i need block some MAC address or devices how can i do it

Hi,
Yes you can block the specific client using MAC Address filtering option in WCS
This option is avialbe in Configure> Security >MAC Filtering
here you can create new template as per your requirement
Go through below link for detail knowledge.
http://www.cisco.com/c/en/us/td/docs/wireless/wcs/7-0/configuration/guide/WCS70cg/7_0temp.html#wp1095263

Cisco Wireless Control System need wireless Lan Controller ?

Cisco Wireless Control System need wireless Lan Controller , for Rogue detection

Hi Joao,
The WCS is used in conjuntion with the WLC (Wireless Lan Controller) for Rogue Detection. It is not a must for this function but more of an add-on :)
The Cisco WCS is an optional network component that works in conjunction with Cisco Aironet Lightweight Access Points, Cisco wireless LAN controllers and the Cisco Wireless Location Appliance.
From this doc;
http://www.cisco.com/en/US/products/ps6305/index.html
Overview of WCS
The Cisco Wireless Control System (WCS) is a Cisco Unified Wireless Network Solution management tool that adds to the capabilities of the web user interface and command line interface (CLI), moving from individual controllers to a network of controllers. WCS includes the same configuration, performance monitoring, security, fault management, and accounting options used at the controller level and adds a graphical view of multiple controllers and managed access points.
WCS runs on Windows 2003 and Red Hat Enterprise Linux ES 4.0 and AS 4.0 servers. On both Windows and Linux, WCS can run as a normal application or as a service, which runs continuously and resumes running after a reboot.
The WCS user interface enables operators to control all permitted Cisco Unified Wireless Network Solution configuration, monitoring, and control functions through Internet Explorer 6.0 or later. Operator permissions are defined by the administrator using the WCS user interface Administration menu, which enables the administrator to manage user accounts and schedule periodic maintenance tasks.
WCS simplifies controller configuration and monitoring while reducing data entry errors with the Cisco Unified Wireless Network Controller autodiscovery algorithm. WCS uses the industry-standard SNMP protocol to communicate with the controllers.
From this good doc;
http://www.cisco.com/en/US/products/ps6305/products_configuration_guide_chapter09186a00806b7270.html#wp1131195
Detect and Locate Rogue Access Points
From this WCS doc;
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a00806f070a.shtml#new5
Rogue Detection under Unified Wireless Networks
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_white_paper09186a0080722d8c.shtml
Hope this helps!
Rob

5s Volume control issues

Anyone having volume control issues? My wife's 5s (less than a month old) is having issues with the up volume. If she mutes it using the down volume, it won't go back up. I can get it to work if I hold the volume a long time and it eventually comes back. Or last time i had to remove her case, hold the volume and release several times before it finally kicked in. Any thoughts or ideas? Thanks.

Hi,
Please test in other computer to see if the issue persists, it may be caused by the bad output channel.
But for better solution, I recommend you go to MSDN forum for further help.
http://msdn.microsoft.com/en-US/
Thanks for your understanding!
Regards,
Ada Liu
TechNet Community Support

Wireless connecion issues using a macbook

Hi,
RE: Wireless connecion issues using a macbook
After doing some google searches, I have come to understand that there is a bug with OSX power management when running on battery which impacts the wireless connection of the macbook, though Apple geniuses are unaware of any such issue. Please see: http://kristopherjohnson.blogspot.com/2006/08/macbook-wireless-connection-drops. html and type in "macbook wireless connection problems" in google for many other discussions on this issue.
For all those who are having wireless connection issues with a macbook:
Plug in the macbook to use mains power (not the battery) to verify that you are impacted by the same bug (I even find sometime unable to connect to the router when on battery so have resorted to starting the machine with mains power plugged in). If that is the problem then here is a work around (taken from above blog):
Open the terminal window and type in the following command: ping -i 5 google.com
(this will ping the google domain every 5 seconds and maintain the wireless activity thus a connection).
I am surprised that Apple are not acknowledging this well known and widely reported bug and fixing the issue. In my case, I dont mind plugging the machine into mains most of the time and that has resolved the problem, otherwise I hope the above pinging works for you.
I discovered the workaround after ditching my old DLink router (though it had done its time) and buying an Airport extreme (£120), a trip to the Apple store (40 miles drive), trying several different people's machine on my network (frustration) and finally google to rescue, more specifically Kristopher Johnson's blog.
NOTE: My macbook worked fine in the Apple store while on battery power which was frustrating but apparently the problem only arises when connecting to consumer grade networks and not commercial ones, which I dont understand technically.
HTH
Regards
Faisal

you can use but you will not get full screen on HDMI output.
Sometimes width or height of the screen was not completely used by ur mac other then that everything would be good.
You need to buy HDMI Output cable for mac something like this
http://store.apple.com/us/product/HA825ZM/A/belkin-mini-displayport-to-hdmi-cabl e-2-m65-ft?fnode=51

Can Wireless Control System Send Alarms As Traps to a trap receiver

Can the Cisco Wireless Control System be configured to send its alarms as SNMP traps to a specified trap receiver ? if so how is that capability configured ? is it thru Notification Receiver ?

Yes, it can. And yes through the Notification Reciever. Pity though, it can only send traps in regards to Guest Account Activity such as guest association and authentication.
Hopefully future versions of WCS will be more versatile in that regard.
Cheers

Inline Posture deployment for non Cisco Wireless Controler

Hi all of you
I have to deploy an Inline Posture to manage non Cisco Wireless Controler ( ZoneDirecteur 1000 Ruckus), It seem easy but I don't know from where to start. All documentation I rode it's about Inline Posture for VPN. I want just to use this Inline Posture to manage Wireless user through ZoneDirector wirelss controler. Thank you.
Regards
Kouassi

So what is the solution for this scenario?
remote site has non-cisco autonomous wireless AP. NAC is centralized. I can not use OOB since there is no support for non-cisco AP in OOB mode. As a result I use InBand mode. This means that local wireless trffic in remote site must travel to central site, go through NAC Server and go back to remote site. Is this correct?

Legal control Issue - License cannot be used

Hi Team,
The sales order has Legal Control: Issue Error, due to this we are unable to deliver the goods. the below message found in the Log details:
Access object: License Master
Key (license nubmer): xxxxx
Validity period not long enough
Requested delivery date for item: 02/20/2012
End of validity period of license: 1231/2011
License cannot be used
we tried to extend the validity of license but it is not allowing. can anyone give some inputs on this error.
Thanks,
Rajam

Its a SAP GTS related error.
I hope you are aware of the License are created under Legal Control in GTS system.
If I'm not wrong, we can maintain License (GTS) by using TCode /SAPSLL/LCLIC01 and if the License is in active mode then can be modified by using TCode /SAPSLL/LCD_CHANGE
If my input didn't assist, then try to post your SAP GTS related query in SCN Forum following, for expertise help on SAP GTS.
- [Forum on *_SAP Global Trade Service_*|SAP Global Trade Services (GTS);
Regards
JP

I have a VIXIA HF R400 and I love it but I cannot find where the wireless controls are?

Were are the wireless controls on the VIXIA HF R400? The manua says what they do but not clear instructions on how to access it.

Hi bgutzman!
Using the CameraAccess app for iOS devices and Android smartphones, you can control the camcorder from a distance while you view the camcorder's image on the smartphone's screen. Not only can you control the camcorder to start and stop recording, you can also record the camcorder's image directly onto your smartphone. The CameraAccess app can be downloaded from either the Apple App Store or the Google Play Store. When this has been done:
1) Set the camcorder to receive remote control commands in the menu.
2) Activate WiFi on the settings screen.
3) Touch the access point with the same SSID as the one you saw earlier when you set the camcorder for remote control.
4) Enter the password.
5) Start the CameraAccess app.
If this is a time sensitive-matter, additional support options are available at Contact Us.
Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

ATV2 OFFICIALLY rolled back to 4.2.1 due to wireless N issues

My ATV prompted me to update it an hr ago, I did, and when it came back up, 4.3 was gone and 4.2.1 was there.. I plugged it into itunes and it said it was up to date... I called apple support and they verified that JUST the ATV2 has been rolled back due to Wireless N and other wireless compatability issues.

TallBearNC wrote:
I had 4.3 on my ATV for weeks. it even said 4.3 in the about screen. You do not know what YOU are talking about.
Once my ATV went to 4.3 a few weeks ago, it could no longer connect to my N network until I turned WMM on, and even then it kept dropped off. So I had to switch my router back to A/G mode.
Yes, there WAS.. and if you don't belive me, ill be HAPPY to show you the ATV2 4.3 IPSW I've had sitting on my desktop for weeks
You are wrong. Take my advice and stop now before you embarrass yourself.

Wireless controler issue

Similar Messages

Maybe you are looking for