WLC 2504 latest version(s)?
What's the story with so many different "latest" releases?
I'm installing a new 2504 so which one do I upgrade to--the controller shipped with 7.0.x
Thanks.
7.2.115.2(ED)7.4.100.60(ED)
7.3.112.0(ED)
7.0.240.0(ED)
This is what's installed. Do I need to upgrade anything else first?
Product Version.................................. 7.0.220.0
Bootloader Version............................... 1.0.16
Field Recovery Image Version..................... 1.0.0
Firmware Version................................. PIC 16.0
Well they are all different flavors. Any of the latest versions are fine and it really comes down to what features you want. I've been running v7.4.x last couple months and it's been fine on my 2504 home environment:). I'm running the beta right now.
Sent from Cisco Technical Support iPhone App
Similar Messages
-
Hi!!! Please help with the solution.
I have one WLC 2504, 4 Cisco 1141 APs and one AP 1602.
Yesterday, I upgrade the WLC with version 7.5.102 to version 7.6.100.
After the upgrade in Message Logs on the WLC at the same time see the following message:
*RRM-MGR-5_0-GRP: Jan 23 08:44:25.449: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 08:35:41.189: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 08:34:17.373: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 08:25:32.125: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 08:24:09.309: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 08:15:23.013: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 08:14:01.213: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 08:05:13.949: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 08:03:53.149: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 07:55:04.905: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 07:53:45.086: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 07:44:55.813: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 07:43:37.010: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 07:34:46.749: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 07:33:28.930: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 07:24:37.669: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 07:23:20.865: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 07:14:28.593: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 07:13:12.789: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 07:04:19.529: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 07:03:04.729: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 06:54:10.493: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 06:52:56.689: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 06:44:01.445: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 06:42:48.645: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.
*sntpReceiveTask: Jan 23 06:35:22.218: #LOG-4-Q_IND: debug.c:2636 Unhandled debug module 5005.[...It occurred 19 times.!]
*RRM-MGR-2_4-GRP: Jan 23 06:33:48.070: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 06:32:36.266: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 06:23:39.030: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 06:22:28.226: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 06:13:29.986: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 06:12:20.186: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 06:03:20.930: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 06:02:12.130: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 05:53:11.890: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 05:52:04.090: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 05:43:02.838: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 05:41:56.039: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 05:32:53.790: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 05:31:47.986: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 05:22:44.758: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 05:21:39.950: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 05:12:35.718: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 05:11:31.910: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 05:02:26.670: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 05:01:23.859: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 04:52:17.606: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 04:51:15.794: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 04:42:08.566: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 04:41:07.750: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 04:31:59.506: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 04:30:59.703: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 04:21:50.450: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 04:20:51.646: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 04:11:41.402: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 04:10:43.598: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 04:01:32.326: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 04:00:35.522: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 03:51:23.258: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 03:50:27.442: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 03:41:14.182: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 03:40:19.378: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 03:31:05.106: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 03:30:11.302: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 03:20:56.042: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 03:20:03.242: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 03:10:46.978: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 03:09:55.178: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 03:00:37.902: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 02:59:47.102: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 02:50:28.826: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 02:49:39.026: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 02:40:19.782: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 02:39:30.983: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 02:30:10.742: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 02:29:22.942: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 02:20:01.698: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 02:19:14.886: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 02:09:52.646: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 02:09:06.842: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 01:59:43.587: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 01:58:58.783: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 01:49:34.546: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 01:48:50.742: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 01:39:25.494: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 01:38:42.687: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 01:29:16.454: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 01:28:34.642: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 01:19:07.402: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 01:18:26.594: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 01:08:58.362: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 01:08:18.554: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 00:58:49.322: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 00:58:10.514: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 00:48:40.266: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 00:48:02.467: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 00:38:31.222: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 00:37:54.411: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 00:28:22.174: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 00:27:46.374: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 00:18:13.106: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 00:17:38.306: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 00:08:04.062: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 00:07:30.262: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 22 23:57:55.022: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 22 23:57:22.222: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 22 23:47:45.958: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 22 23:47:14.158: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 22 23:37:36.906: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 22 23:37:06.106: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 22 23:27:27.826: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 22 23:26:58.026: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 22 23:17:18.762: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 22 23:16:49.962: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 22 23:07:09.686: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 22 23:06:41.870: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.
With what may be the problem exists? Any suggestion?Have you upgraded the FUS to 1.8.0.0? What happens if you try to boot from v7.5 do you see the messages and maybe boot back to v7.6?
Here is what the doc mentions about the error
Error Message %DEBUG-4-INVALID_MODULE: Unhandled debug module [dec].
Explanation This module cannot be debugged.
Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.
http://www.cisco.com/en/US/docs/wireless/controller/message/guide/msgs4.html#wp1000708
Sent from Cisco Technical Support iPhone App -
WLC 2504 Crash version 8.0.110.0
Hey guys,
I updated the software to version 8.0.110.0 for the WLC 2504 two days ago, it worked fine until this morning that it crashed, it's was blinking amber and green and the SYS light as well, I couldn't ping it, then I took the power cable off, and reboot it to get it up again, does anybody knows the reason of it, and also if there is some work around that I can do in order to solve it.
I'll be waiting for your comments.
Regards,
Alberto Badilla.Hi,
We had a same experince with same IOS software 8.0.110(we have 3 controllers), we found that iuuses with legecy access points like 1240,1142,1250 ap's. Only working with either 2700/3700/1700 ....
Thanks & Regards,
Naveen A -
Install GoDaddy wildcard SSL on WLC 2504 conroller
I'm attempting to install a GoDaddy wildcard ssl certificate onto a WLC 2504 running version 7.4.100.0.
I am getting the error "#SSHPM-3-KEYED_PEM_DECODE_FAILED: sshpmcert.c:4055 Cannot PEM decode private key" when downloading the .pem file to the controller.
What I have attempted to do was to export the certificate from a Windows 2008 R2 server into a .pfx file. The file contained the private key and all possible root certficates (in this case a root and a intermediate cert). Now I took this .pfx file and attempted to create a .pem file with openssl using the following command: openssl pkcs12 -in myssl.pfx -out mynewssl.pem -passin pass:mypassword -passout pass:mypassword
Now I have opened the .pem file and verified it does contain the private key and the three certificates (wildcard, intermediate and root).Seth,
I had a similar problem, and saw the solution in another post on this forum. I am cross-posting this to help anyone else out there who might be searching for this answer.
Kudos to Robert Wells for finding this:
"I have it fixed now. The problem was the cisco only supports openssl 0.9.8x. I was using 1.0.1c. I used 0.9.8x and it worked perfectly fine."
The Windows version of OpenSSL I used was the 0.9.8y Light version from:
http://slproweb.com/download/Win32OpenSSL_Light-0_9_8y.exe
I hope this helps someone out there with this problem.
- Ken -
Query About Cisco WLC 2504 TDLS
Dear Friends,
One of my client want to encrypt data over the wireless. I have cisco WLC 2504 IOS Version 7.2.0.0.
Please help me on this. I think by-default data encrypt is enable. If not so how can I enable it. If I enable it is there any impact to my wireless user's.
Please help me out .....
Thanks & Regards,
Rahul WankhadeHow to enable:
http://www.cisco.com/c/en/us/support/docs/wireless/2500-series-wireless-controllers/113034-2500-deploy-guide-00.html#enable
Impact:
2500, WiSM2, WLC2—These platforms by default will not contain DTLS. To turn on data DTLS, you must install a license. These platforms will have a single image with data DTLS turned off. To use data DTLS you will need to have a license.
http://www.cisco.com/c/en/us/products/collateral/wireless/2500-series-wireless-controllers/data_sheet_c78-645111.html
AS per cisco: Encryption limits throughput at both the controller and the access point.
Regards
Dont forget to rate helpful posts -
WLC 2504 - Ap join fails with "Unknown AP type. Using Controller Version!!!"
Hi,
I haven't encountered this problem before. On my WLC 2504 I've tried now software versions 8.0.100.0, 7.6.130.0 and 7.4.121.0 (as per recommendation from other supportforum-posts), but still get this debug error when I'm trying to join ap models 1142 and 2602:
(Cisco Controller) >debug capwap errors enable
(Cisco Controller) >*spamApTask5: Jan 02 02:11:46.549: Unknown AP type. Using Controller Version!!!
*spamApTask0: Jan 02 02:11:46.550: 88:43:e1:78:10:08 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 5,joined Aps =0
*spamApTask5: Jan 02 02:11:56.670: f8:66:f2:14:4e:c1 Deleting AP 10.68.254.101 which has not been plumbed
*spamApTask5: Jan 02 02:11:56.673: f8:66:f2:14:4e:c1 DTLS connection was closed
(Cisco Controller) >
Does anyone know what is failing here? Surely the ap's should be "known" in these software versions?
Best
Bent EskilHi I have the same issue, today i rebooted the controller after that no Access Point is joining the controller. While debug i can see same logs as given above. I have configured option 43 and 60 as well on cisco switch. Pool commands are:
ip dhcp pool Room-1
host 192.168.30.113 255.255.255.0
client-identifier 0188.1dfc.f7cb.30
default-router 192.168.30.3
domain-name mina.local
option 43 hex f108.aca8.1e68
dns-server 192.168.30.1 4.2.2.2
option 60 ascii "Cisco AP c3702
I have checked the time and country code all fine but still Access point are not joining. Can you help me out to figure out the issue.
Thanks -
Dear Friends,
I am using Cisco WLC 2504 current software version is 7.0.220.0 and I want to upgrade it to the latest version which is 8.x.x.x.
Could you please help and advice the best way of doing it? Also can I upgrade direct to the latest version or do I have to upgrade step by step?
Thank you very much for your help and support.
Thanks
UmarHi
Could you please help and advice the best way of doing it? Also can I upgrade direct to the latest version or do I have to upgrade step by step?
Yes, you can go directly to 8.0.x from 7.0.x code. Refer below link
http://www.cisco.com/c/en/us/td/docs/wireless/controller/release/notes/crn80mr1.html#68333
Make sure you refer the release notes for any known issues with this code. Also upgrade FUS to 1.9.0.0 as well. This will take around 30 min downtime as well.
http://www.cisco.com/c/en/us/td/docs/wireless/controller/release/notes/fus_rn_OL-31390-01.html
If you have different AP models, MSE, Prime products, refer this compatibility matrix as reference.
http://www.cisco.com/c/en/us/td/docs/wireless/compatibility/matrix/compatibility-matrix.html
HTH
Rasika
**** Pls rate all useful responses **** -
WLC 2504 sudden network instability
Hello,
we're running a WLC 2504 with two SSIDs on it. It is connected to to a small PoE switch. Standard untagged vlan. A handfull APs connected to it. No DHCP, the APs have all static IP addresses.
All of a sudden we're having a number of issues with the network connection:
APs restarting
The APs restart every now and then reporting that their IP is being used by another device. Looking through the logs there are two MAC addresses that are reported as using the APs IP address. These two MAC addresses have unknown vendor IDs.
Warning: AP with Base Radio MAC f8:72:ea:7c:9d:e3 has found its IP Address 0.2.146.0 being used by a machine with MAC
Address 04:c6:f8:40:00:00 (The other mac that is reported is 04:cc:90:40:00:00)
AP 'AP5', MAC: 0c:68:03:dd:1b:80 disassociated previously due to Link Failure. Uptime: 4 days, 00 h 48 m 50 s . Reason: Capwap WTP Event request.
So: There are two MACs that use the IP addresses of 7 APs?!?! And there is no vendor to be found for these MACs?
Ping timouts on the webGUI and CLI
I have a ping running on the IP for managing the device. This is running fine for ages. As soon as I connect via webGUI or CLI I lose packets. Get timeouts etc. some packets get through some don't. More of the latter. So ping is fine but any other traffic seems to be impacted heavily.
What we have done for troubleshooting
Checked duplex/speed settings of the interfaces. Everything ok.
Connected to another switchport. Same.
Changed the IP address of the management port. Same.
Swapped places with a laptop with the same IP address --> Worked fine.
Plugged in a completely new device, installed the latest firmware (7.6) and uploaded the config from the other one. Same.
Restarted the default gateway for the subnet the controler is on.
So now we're at the end of our knowledge. It seems to be a non-physical network issue, but we're a small team and no one has changed anything they say :-/
Any ideas what we could check next?
KatHello,
thanks for your suggestions. It's hard to find those two MAC addresses. As they seem to be virtual I cannot get a hint from the vendor ID. A show mac-address table on the switch the WLC is connected to doesn't show those two
I found an error in the WLC AP config. AP1 had the same IP as AP5 and a wrong netmask. I changed that. Unfortunately that doesn't solve our problem.
Here are some more messages from the WLC's log:
AP 'AP3', MAC: 0c:68:03:dd:34:00 disassociated previously due to Link Failure. Uptime: 4 days, 15 h 04 m 15 s . Reason: Capwap WTP Event request.
AP Disassociated. Base Radio MAC:0c:68:03:dd:34:00
AP's Interface:1(802.11a) Operation State Down: Base Radio MAC:0c:68:03:dd:34:00 Cause=Heartbeat Timeout Status:NA
AP 'AP3', MAC: 0c:68:03:dd:34:00 disassociated previously due to Link Failure. Uptime: 4 days, 15 h 00 m 45 s . Reason: Capwap WTP Event request.
RF Manager updated TxPower for Base Radio MAC: 0c:68:03:dd:34:00 and slotNo: 0. New Tx Power is: 2
AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:0c:68:03:dd:16:e0 Cause=Max Retransmission Status:NA
IDS Signature attack detected. Signature Type: Standard, Name: Deauth flood, Description: Deauthentication flood, Track: per-signature, Detecting AP Name: AP7, Radio Type: 802.11b/g, Preced: 9, Hits: 500, Channel: 6, srcMac: C2:9F:DB:21:47:60
This is the sh run-config of our WLC including one AP:
>show run-config
System Inventory
NAME: "Chassis" , DESCR: "Cisco 2500 Series Wireless LAN Controller"
PID: AIR-CT2504-K9, VID: V01, SN: PSZ17381EPZ
Burned-in MAC Address............................ 50:17:FF:27:12:80
Maximum number of APs supported.................. 15
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.4.110.0
Bootloader Version............................... 1.0.18
Field Recovery Image Version..................... 1.0.0
Firmware Version................................. PIC 16.0
Build Type....................................... DATA + WPS
System Name...................................... UK-BRI-WFAPC
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
IP Address....................................... 172.17.128.12
Last Reset....................................... Power on reset
System Up Time................................... 4 days 0 hrs 46 mins 6 secs
System Timezone Location.........................
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
Configured Country............................... GB - United Kingdom
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +20 C
External Temperature............................. +25 C
Fan Status....................................... 4000 rpm
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 3
Number of Active Clients......................... 6
Memory Current Usage............................. Unknown
Memory Average Usage............................. Unknown
CPU Current Usage................................ Unknown
CPU Average Usage................................ Unknown
Burned-in MAC Address............................ 50:17:FF:27:12:80
Maximum number of APs supported.................. 15
AP Bundle Information
Primary AP Image Size
ap1g2 9568
ap3g1 11288
ap3g2 11196
ap801 7164
ap802 8568
c1130 5072
c1140 9416
c1250 6944
c1520 8044
c602i 3736
Secondary AP Image Size
ap3g1 5792
ap801 5192
ap802 5232
c1100 3084
c1130 4964
c1140 4992
c1200 3364
c1240 4812
c1250 5504
c1310 3136
c1520 6404
c3201 4324
c602i 3716
Switch Configuration
802.3x Flow Control Mode......................... Disable
FIPS prerequisite features....................... Disabled
secret obfuscation............................... Enabled
Strong Password Check Features:
case-check ...........Enabled
consecutive-check ....Enabled
default-check .......Enabled
username-check ......Enabled
Network Information
RF-Network Name............................. RFGROUP
Web Mode.................................... Disable
Secure Web Mode............................. Enable
Secure Web Mode Cipher-Option High.......... Disable
Secure Web Mode Cipher-Option SSLv2......... Disable
Secure Web Mode RC4 Cipher Preference....... Disable
OCSP........................................ Disabled
OCSP responder URL..........................
Secure Shell (ssh).......................... Enable
Telnet...................................... Disable
Ethernet Multicast Forwarding............... Disable
Ethernet Broadcast Forwarding............... Disable
AP Multicast/Broadcast Mode................. Multicast Address : 0.0.0.0
IGMP snooping............................... Disabled
IGMP timeout................................ 60 seconds
IGMP Query Interval......................... 20 seconds
MLD snooping................................ Disabled
MLD timeout................................. 60 seconds
MLD query interval.......................... 20 seconds
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
Cisco AP Default Master..................... Disable
AP Join Priority............................ Disable
Mgmt Via Wireless Interface................. Disable
Mgmt Via Dynamic Interface.................. Disable
Bridge MAC filter Config.................... Enable
Bridge Security Mode........................ EAP
Mesh Full Sector DFS........................ Enable
AP Fallback ................................ Enable
Web Auth CMCC Support ...................... Disabled
Web Auth Redirect Ports .................... 80
Web Auth Proxy Redirect ................... Disable
Web Auth Captive-Bypass .................. Disable
Web Auth Secure Web ....................... Enable
Fast SSID Change ........................... Disabled
AP Discovery - NAT IP Only ................. Enabled
IP/MAC Addr Binding Check .................. Enabled
CCX-lite status ............................ Disable
oeap-600 dual-rlan-ports ................... Disable
oeap-600 local-network ..................... Enable
mDNS snooping............................... Disabled
mDNS Query Interval......................... 15 minutes
Port Summary
STP Admin Physical Physical Link Link
Pr Type Stat Mode Mode Status Status Trap POE
1 Normal Forw Enable Auto 1000 Full Up Enable N/A
2 Normal Forw Enable Auto 100 Full Up Enable N/A
3 Normal Forw Enable Auto 1000 Full Up Enable Enable (Power Off)
4 Normal Disa Enable Auto Auto Down Enable Enable (Power Off)
AP Summary
Number of APs.................................... 7
Global AP User Name.............................. Not Configured
Global AP Dot1x User Name........................ Not Configured
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
AP7 2 AIR-CAP1602I-E-K9 f8:72:ea:e4:9a:81 default location 1 GB 1
AP1 2 AIR-CAP1602I-E-K9 f8:72:ea:7c:9d:e3 default location 1 GB 1
AP3 2 AIR-CAP1602I-E-K9 f8:72:ea:e4:9c:57 default location 1 GB 1
AP6 2 AIR-CAP1602I-E-K9 f8:72:ea:e4:9a:90 default location 1 GB 1
AP2 2 AIR-CAP1602I-E-K9 f8:72:ea:7c:9b:63 default location 1 GB 1
AP4 2 AIR-CAP1602I-E-K9 f8:72:ea:e4:9a:9b default location 1 GB 1
AP5 2 AIR-CAP1602I-E-K9 f8:72:ea:e4:9a:cb default location 1 GB 1
AP Tcp-Mss-Adjust Info
AP Name TCP State MSS Size
AP7 disabled -
AP1 disabled -
AP3 disabled -
AP6 disabled -
AP2 disabled -
AP4 disabled -
AP5 disabled -
AP Location
Total Number of AP Groups........................ 0
Site Name........................................ default-group
Site Description.................................
NAS-identifier................................... UK-BRI-WFAPC
AP Operating Class............................... Not-configured
RF Profile
2.4 GHz band.....................................
5 GHz band.......................................
WLAN ID Interface Network Admission Control Radio Policy
1 corporate Disabled None
2 dirtynetwork Disabled None
3 dirtynetwork Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
AP7 2 AIR-CAP1602I-E-K9 f8:72:ea:e4:9a:81 default location 1 GB 1
AP1 2 AIR-CAP1602I-E-K9 f8:72:ea:7c:9d:e3 default location 1 GB 1
AP3 2 AIR-CAP1602I-E-K9 f8:72:ea:e4:9c:57 default location 1 GB 1
AP6 2 AIR-CAP1602I-E-K9 f8:72:ea:e4:9a:90 default location 1 GB 1
AP2 2 AIR-CAP1602I-E-K9 f8:72:ea:7c:9b:63 default location 1 GB 1
AP4 2 AIR-CAP1602I-E-K9 f8:
RF Profile
Number of RF Profiles............................ 0
Out Of Box State................................. Disabled
RF Profile Name Band Description 11n-client-only
AP Config
Cisco AP Identifier.............................. 15
Cisco AP Name.................................... AP7
Country code..................................... GB - United Kingdom
Regulatory Domain allowed by Country............. 802.11bg:-E 802.11a:-E
AP Country code..................
................ GB - United Kingdom
AP Regulatory Domain............................. -E
Switch Port Number .............................. 1
MAC Address...................................... f8:72:ea:e4:9a:81
IP Address Configuration......................... Static IP assigned
IP Address....................................... 172.17.128.24
IP NetMask....................................... 255.255.128.0
Gateway IP Addr.................................. 172.17.128.1
Domain...............
Name Server......................................
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ default location
Cisco AP Floor Label............................. 0
Cisco AP Group Name.............................. default-group
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ....
............................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ..
....................... kern
S/W Version .................................... 7.4.110.0
Boot Version ................................... 15.2.2.0
Mini IOS Version ................................ 7.4.1.37
Stats Reporting Period .......................... 180
Stats Collection Mode ........................... normal
LED State........................................
Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-CAP1602I-E-K9
AP Image...............................
.......... C1600-K9W8-M
IOS Version...................................... 15.2(2)JB2$
Reset Button..................................... Enabled
AP Serial Number................................. FGL1725W7F7
AP Certificate Type.............................. Manufacture Installed
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system loggi
ng host..................... 255.255.255.255
AP Up Time....................................... 3 days, 23 h 26 m 50 s
AP LWAPP Up Time................................. 0 days, 00 h 14 m 12 s
Join Date and Time............................... Tue Jan 28 18:11:43 2014
Join Taken Time.................................. 0 days, 00 h 11 m 41 s
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211n-2.4
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
Radio Mode .................................. Local
CellId ...................................... 0
Station Configuration
Configuration ............................. AU
TOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 0c:68:03:dd:16:e0
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
6000 Kilo Bits........................... SUPPORTED
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... SUPPORTED
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
MCS Set
MCS 0.................................... SUPPORTED
MCS 1.................................... SUPPORTED
MCS 2.................................... SUPPORTED
MCS 3.................................... SUPPORTED
MCS 4.................................... SUPPORTED
MCS 5.................................... SUPPORTED
MCS 6.................................... SUPPORTED
MCS 7.................................... SUPPORTED
MCS 8.................................... SUPPORTED
MCS 9.................................... SUPPORTED
MCS 10................................... SUPPORTED
MCS 11................................... SUPPORTED
MCS 12..
................................. SUPPORTED
MCS 13................................... SUPPORTED
MCS 14................................... SUPPORTED
MCS 15................................... SUPPORTED
MCS 16................................... DISABLED
MCS 17................................... DISABLED
MCS 18................................... DISABLED
MCS 19................................... DISABLED
MCS 20................................... DISABLED
MCS 21................................... DISABLED
MCS 22................................... DISABLED
MCS 23................................... DISABLED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ GB
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 13
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 4
Tx Power Level 1 .......................... 16 dBm
Tx Power Level 2 .......................... 13 dBm
Tx Power Level 3 .......................... 10 dBm
Tx Power Level 4 .......................... 7 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 3
Tx Power Assigned By ...................... DTPC
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 6
Channel Assigned By ....................... DCA
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11,12,
......................................... 13
TI Threshold .............................. -50
Legacy Tx Beamforming Configuration ....... CUSTOMIZED
Legacy Tx Beamforming ..................... ENABLED
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
Diversity.................................. DIVERSITY_ENABLED
802.11n Antennas
A....................................... ENABLED
B....................................... ENABLED
C....................................... ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................
CleanAir Management Information
CleanAir Capable......................... No
Radio Extended Configurations
Beacon period.............................. 100 milliseconds
Beacon range............................... AUTO
Multicast buffer........................... AUTO
Multicast data-rate........................ AUTO
RX SOP threshold........................... AUTO
CCA threshold.............................. AUTO -
Acs 5.3 and wlc 2504 config with restricted network access
Hello,
i submit you the following issue that i'm actually facing:
i must configure a secured wireless network with access restriction based on SSID. the equipements are : cisco wlc 2504 (soft 7.3) cisco secure acs aplliance 1121 (soft 5.4) .
the users that will connect to the network are regrouped by identity groups, each identity group having it's own SSID. Clearly each group of users must access only one SSID.
i followed the procedure below to configure it:
-- creating user identity groups;
-- creating users and assigning them to the groups;
--- creating authorization profiles for each SSID under policy element/ authorization and permission/network access/authorization profiles and putting the Airespace-Wlan-Id(the SSID number) in the radius tab.
--- assigning the authorization profiles to the identity groups under access policies.
after all these config the users can access the network using there userid/password configured. But the problem is Every user can access every SSID, seems like the restriction is so not very well configured.
i found some documentation on this kind of config but the version of ACS used seems older than the one that i use, so menu are very different.
Please can someone provide with the right steps to follow to achieve this kind of config.
tkx in advanceYes.. you only have to add the end filter like what I posted... as far as the calling station id in the WLC security tab, it doesn't matter because that is not used when using 802.1x. I would also try to not enable everything that you have just to start from the basic and make sure it works first. The WAP Authentication Method might or might not work for you. Uncheck that for now and when you have a successful authentication, look at the monitor log and see what radius attributes are being sent, because those attributes is what you can use to build your policies.
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered" -
WLC 2504 - French characters for guest web login page
Good day,
I have recently installed a WLC 2504 and I have the following issue:
When I modify the text for the web login page (Under security/Web Auth/Web Auth page), if I use french caracters such as (é, è, à, etc...) in the message body, it does not show up correctly on users computers. As we're a bilingual country, I must put a bilingual text message. Are there any settings or workaround out there to rectify this?
We're on version 7.2.103.0
Thanks,
EricThanks Scott, I'll have a look at the documentation.
Right after sending this post, I tried typing the actual HTML code for the character instead and it seems to be working. I'm curious about custom webauth page, we may be able to customize it more than we thought we could do.
Cheers,
Eric -
Hi Guys,
What configuration should I use in order to configure HA using 2x Cisco WLC 2504 ?
- Do I need to have licenses for 2x Controllers ? I have only one WLC with license installed.
At the moment I have the following scenario below.
AIR-CT2504-K9 – Primary (30 Aps Supported)
AIR-CT2504-HA-K9 – Secondary (0 license)
Software Version - 7.6.130.0 (Both Controllers)
Both controllers are going to be in the same place.
Can anyone help me please ?
Thanks,
EvertonThanks Scott Fella !
Just one more question.
Should I use a crossover cable to connect the primary controller to the secondary ? Or should I use a switch to connect them ?
Thanks,
Everton -
This might be a really stupid question but I need to ask just so that I get a definitive answer. I have a customer that is using a WLC 2112 and has maxed out the licenses for the WLC. I have suggested for him to purchase a 2504 with 30 or 40 licenses to replace the existing 2112. He doesn't want to purchase 30 to 40 licenses and doesn't want to remove the 2112 from the network environment. He would rather purchase a WLC 2504 with 15 licenses and just add that into the network.
My question is, will there be a problem running a 2504 and a 2112 on the same network? Or can I just make one a primary and one a secondary?That should be fine. Just make sure the WLCs are running the same code version and everything should work fine. This is required for APs failover from one WLC to another. You don't want the APs upgrading or downgrading code versions every time the ap moves from the primary to the secondary WLC.
Sent from Cisco Technical Support iPhone App -
LWAP 1231G can't join an WLC 2504 , Unsupported!!
Dear All,
I have WLC 2504 with 7.2.103.0 software version , & 2 different LWAP 1262n & 1231G with "c1200-rcvk9w8-mx.124-21a.JA" Image.
The 1262n is joined to the to the controller and working fine but the 1231G it cann't join the controller , the controller says "Join request received from an unsupported AP" !!
i will attaches the logs for this AP.
please can any one help.If you want to use 1230, then the "highest" WLC version you can run is the 7.0.235.3.
It says so in the Release Notes under the heading Software Release Support for Access Points, Table 1-1. -
WLC 2504 Hangs after upgrading 7.4 firmware
Hi All
We have WLC2504 ( Upgraded to Firmware 7.4) and AP'S are AP 1602
When Wirless Controller trying to Connects AP'S then they are hanging and same is happening for AP'S os we are not able to do configuration.
Pinging continous is breaking for WLC IP Address.
We have upgraded to Latest Firmware 7.4...
I have read that this is Bug in Firmware 7.4....What is the work around??
ThanksHi,
Make sure your WLC 2504 is sync with the NTP Server. -
Recommended to upgrade WLC to software version 4.0.179.8?
Hi Sir,
I'm deploying a few WLC 4404-100 in a Mobility Group. They are installed with software version 4.0.155.5.
I understand that the latest version is 4.0.179.8. Is it recommended to upgrade the WLCs to this version?
Please advise.
Thank you.
B.Rgds,
Lim TSHi,
I'm having a WLC 4404-100 running software version 4.0.179.8. Doing functional test now.
Created a WLAN with 802.1x and WEP 104-bits.
My wireless card is 3Com 3CRWE62092B. Windows XP SP2. Associated to the Lightweight AP and passed my EAP PEAP-MSCHAPv2 authentication with a backend Microsoft domain controller.
The connection is fine. However, every about 15 minutes, XP prompts the username/password dialog box again. My connection is cut off until I re-authenticate.
I never faced this problem before using Odyssey client previously with a WLC running software version 155.5.
Please advise.
Thank you.
B.Rgds,
Lim TS
Maybe you are looking for
-
We have 3 G5 towers and an older g4 tower with a apple studio display. For some reason i had it on sleep and when we came into the office this morning the display was all out of wack. Does anyone know the problem. It's almost like it's trying to fit
-
Oracle portal Favorites portlet
Has anyone found a way to default for other users the links in the favorites portlet? Or get rid of the oracle links? We would like to roll this out, but we will not if we cannot even put our default links in there. There are no edit_defaults links a
-
i need to download se10 transport detail (Parent request and child request with description of task) , any idea?? or any view from which i can download into excel in proper format.
-
Preview 7.0 not opening in 10.9
I tried to open a scanned document in PDF format and got an Error Mesdsage saying that Preview does not work on this computer. I am using Mavericks 10.9
-
I am using Illustrator CS4 on a Vista OS and don't see the red, yellow and green circles on the Application Bar. Can anyone help?