Wrong pass word entred more than 10 times.

wrong pw entred by children= itouch diactivated how to restore it ?

If you repeatedly enter the wrong passcode, iPhone or iPod touch will be disabled for longer intervals, before you can try again. After too many unsuccessful attempts, you won't be able to try again until you connect to the computer you normally sync with. Note that starting with iPhone 2.1 software, there is a setting to cause the device to erase itself after 10 consecutive incorrect password attempts. This setting is off by default. It can be turned on by tapping Settings > General > Passcode Lock after you enter a correct passcode.
See:
http://support.apple.com/kb/HT1212

Similar Messages

My ipad had been frozen my daughter put wrong pass words more than 3 times its written on the screem connect to itunes what shall i do please.

My ipad had been frozzen my daughter puts the passwords wrong more than 3 times ,And its written on the screem connect to itunes .What shall I do please?Thank you.

You have to restore the device within iTunes. You want to use the same computer that you always sync with so that you can restore your app data and settings. You can restore with any other computer, but you will lose everything on the iPad.
Instructions can be found here.
http://support.apple.com/kb/ht1212
You may need to restore using Recovery Mode. You can read about it here.
http://support.apple.com/kb/ht4097
Recovery Mode Instructions
Disconnect the USB cable from the iPad, but leave the other end of the cable connected to your computer's USB port.
Turn off iPad: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for iPad to turn off.
If you cannot turn off iPad using the slider, press and hold the Sleep/Wake and Home buttons at the same time. When the iPad turns off, release the Sleep/Wake and Home buttons.
While pressing and holding the Home button, reconnect the USB cable to iPad. When you reconnect the USB cable, iPad should power on.
Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears you can release the Home button.
If necessary, open iTunes. You should see the recovery mode alert that iTunes has detected an iPad in recovery mode.
Use iTunes to restore iPad.

My ipad is locked after entring wrong pasword more than 10 times and i did not back up my ipad. now my device is not able be conncted with i tunes to restore or update, i need a help how can i unlock it?

my ipad is locked after entring wrong pasword more than 10 times and i did not back up my ipad. now my device is not able be conncted with i tunes to restore or update, i need a help how can i unlock it?

You have to restore the iPad by syncing to the original computer that you synced to.
This article explains the process.
http://support.apple.com/kb/ht1212

HT2729 im locked out of my i phone i used the wrong pass word the computer that i used to setup my phone does not work any more, what can i do i am using a computer now but it wont synic my phone

im locked out of my phone i used the wrong pass word the computer that i used to set it up no longer works

Hi ,
I'm sorry you have to put your device in the DFU mode which means that you're gonna lose your data in your phone
Have you upload something in your cloud ?
I'm here if you need more help

HT1212 My little children Majd enter the wrong passcode for more than 10 times, my iPhone automatically got reset all data was deleted. I managed to retrieve the contacts only but I'm unable to retrieve my SMS's and my photos???? Can you help me please ??

My little children Majd entered the wrong passcode for more than 10 times, my iPhone automatically got reset all data was deleted. I managed to retrieve the contacts only but I'm unable to retrieve my SMS's and my photos???? Can you help me please ???

Hi,
Did you ever back up your phone on the computer?
Did you use photo stream at all?
May I suggest changing your passcode lock to a letters and numbers lock (if not all ready it will make your iphone more secure and a restore lock otion shouldent be needed). Then change your setting as well preventing restore after ten incorect passwords.
kc

HT201274 my phone is lock because i prees wrong password more than 10 times

My phone is lock because i prees wrong password for more than 10 times. I can open my phone what should i do?

Open iTunes on computer, connect iPhone to computer with USB cable. Hold both Home and Power buttons on iPhone until iTunes recognizes iPhone in Recovery Mode. This usually takes about 20 seconds of holding both buttons. Restore the iPhone Firmware. At the end Restore from your iTunes Back-Up or use iCloud to get your data back.

How to share more than one Time Machine folder

Hi,
With Snow Leo Server I found how to find how to share more than one Time Machine Folder but I can't see how to do the same with Lion Server, could you help me with that ?
The goal of that is to offer one TM folder per user which is located on a dedicated partition in order to limit the size of TM backups per user (150Gig).
In Lion, in can only share one TM folder for everybody and I didn'tfind if I can set a limit size per user...
Thank you in advance,

I have figured out a way to enable multiple backup targets.
However, it's one of these things I wouldn't want to describe to anyone except true programmer types, because everyone else has a 90%+ chance of messing up their system if they do something wrong.
It involves turning off file sharing, and then editing the plist files in /private/var/db/dslocal/nodes/Default/sharepoints/
The gist of it is this:
a) first create all the share points you later want to use for TimeMachine, and set them up for afp-only file sharing, also create one TM target, which you can either use later, or have there so the system has one entry it knows how to handle. I just made a bogus one that I'm not actively using.
b) turn off file sharing in Server.app
c) turn off TimeMachine in Server.app
d) now you can edit the files, the easiest is with Xcode, so you may want to install that first
e) for each sharpoint you made in a) there will be a corresponding .plist file in the location indicated, these are the files that need to be edited.
f) for each of these files
     1) the item0 string property in the timeMachineBackup array must be switched from 0 to 1
     2) a new key of type array with the name timeMachineBackupUUID must be created
     3) in the newly created array an item of type string must be placed with the value of a UUID, which can be created with the shell command uuidgen
g) make sure all the edited plist files are saved
h) turn on TimeMachine in the Server.app again
If all went well, you now should be able to go to one of your networked client computers and see all the time machine share points just created as options for being a time machine target.
Anyway, if you go that route: be careful, don't blame me if you muck things up...

How to pass a variable more than one values?

How to pass a variable more than one values?

You can't.
During 1 session, 1 ODI variable can have only 1 value at a time.
If you need more than 1 value, you will have to do somethink like a loop inside your package, and refresh the variable value each time.

I have contacted apple for more than 5 times, but no reply

Hi , i have renewed my iphone developer program for 99$ , But i used to get the message that "my account is expired please renew it" , later now my apps too disappeared in appstore.I have contacted apple support for more than 5 times, but no reply.What is happening.Can some one please explain please.

"Apple will fix all these problems during a week."
Or not.
There are many devs who still have NO access to ANY part of the developer website.
Apple is aware of this (a dev support person telephoned me last week) but, so far, there is no fix or work-around.
It may be true that the developer site has access for SOME subscribers; it is NOT true that everyone is able to get resources shown as "online" on the status page -- many of us have ZERO access.
So, when Apple says 'this week' you have to balance that with the FACT that their assessment of the current status, ie. everyone has limited access now, is wrong/untruthful.
Anyone who doubts this should simply look at other posts in this forum -- lots of folks can't get into the site -- just an infinite loop from login to grey linen maintenance page and back.

CVI Error : After more than 2000 times connect to database.

Dear all:
After connect to the database more than 2000 times ,CVI shows below error,( I also used the DBdiscoected to free system resources )
It seems out of memory, but when I checked the memory usage with resource track , memory leak is not found .
and the physical memory of PC is enough .
All of your advice is appreciated.
Tks

Hi -
I just setup an ran a simple program which connected and disconnected from a databse 2500 times without error. My program was simply a loop around DBConnect and DBDisconnect, checking for errors after each call.
Please tell us more about your system. What version of CVI are you using? Also, what is your OS? How many connections do you have open at a time?
Also, from your screenshot, I see that it mentions "Native error code -2147024882". According to this KnowledgeBase article, native error code messages mean that an error occurred in the database itself, and the code is being passed back to CVI to be handled. From a quick google search on this error code, it appears to mean "Not Enough Storage is available to complete this operation".
If you are able to condense your code into a version that we can run, which reproduces the error, you can post it and we'll take a look at it. Also, I would recommend looking more into the -2147024882 error in regard to the database that you are using.
Best Regards,
John M
National Instruments
Applications Engineer

MGW: How to configure subscriber to try reconnect more than 16 time?

In MGW we have registered a WMQ foreign queue and added a subscriber and a propagation schedule for INBOUND_PROAGATION. In general, everything seems to be working fine. We do successfully get messages from WMQ.
However, admins restart WMQ every night. So, every morning when we come in we see this in the view MGW_SUBSCRIBERS:
SUBSCRIBER_ID = SUB_WMQ2AQ_EFLDRTRANS
FAILURES = 16
LAST_ERROR_DATE = [today]
LAST_ERROR_TIME = [around 5:20 AM]
LAST_ERROR_MSG = MQSeries queue manager, MV17WA01, creation failed errorcode = 800
We have found that if WMQ is restarted fast enough, before the subscriber fails 16 times, everything works fine again. Also, we have found that after 16 failures, all we have to do is reset the subscriber and everything works fine again.
So, question: How can we configure the subscriber so that it tries to reconnect more than 16 times?
TIA. ASD
Edited by: user11135387 on Apr 1, 2011 5:17 AM

hi,
Suppose my form contains the following fields as:
Project,Category,Start Time,End Time,Task Assigned,Task Description
and I want to apply databank values for these fields
Steps which i do are as follows.
1. First of all i Configure the databank file as:
Project,Category,Start Time,End Time,Task Assigned,Task Description
and the values pass are :
Orgnization Process,General,13: 00,14 : 00,test1,test2(in the first row)
NMDGF,General,14:00,15:00,test3,test4(in the second row).
2. After configuring the databank file i have to link with Script node. But since there are more than one fields so how i can link the csv file with script node?
as for the single variable script node , i just substitute the value and link with the databank file its work perfectly fine and it add the folowing code in java code
getDatabank("Timesheet Project").getNextDatabankRecord(); in the starting of run function
3. So i have to add custom code for fetching the value for the next field? As I am not so gud in Java Code so what wil be the code to fetch the values for the next field from CSV file

HT201263 Hi, I forgot the password of my iphone4s I tried more than ten times and it lock me out with a message to connect the iPhone with itunes on the screen but the itunes doesn't recognise it. What can I do?

Hi, I forgot the password of my iphone4s I tried more than ten times and it lock me out with a message to connect the iPhone with itunes on the screen but the itunes doesn't recognise it. What can I do?

Locked Out, Forgot Lock or Restrictions Passcode, or Need to Restore Your Device
1. iTunes 10 for Mac- Update and restore software on iPod, iPhone, or iPad
2. iOS- Forgotten passcode or device disabled after entering wrong passcode
3. iPhone, iPad, iPod touch: Wrong passcode results in red disabled screen
4. iOS- Understanding passcodes
5. What to Do If You've Forgotten Your iPhone's Passcode
6. How to Recover Forgotten iPhone Restrictions Passcode | The iPhone and iPad
7. Restoring iPod touch after forgotten passcode
8. RecBoot: Easy Way to Put iPhone into Recovery Mode - if all else fails.
Forgotten Restrictions Passcode Help
1. How to Recover Forgotten iPhone, iPad Restrictions Passcode
If this method does not work, then you will need to fully Restore your
device as New
Also, see iTunes- Restoring iOS software.

I have iPhone 4s and i switch find my iphone on ! my problem that i have kids who know my apple ID and they put it like more than 10 times and they block it. my iphone wouldn't open or format in right way. plz help

i have iPhone 4s and i switch find my iphone on ! my problem that i have kids who know my apple ID and they put it like more than 10 times and they block it. my iphone wouldn't open or format in right way. plz help

If your kids blocked the phone by repeatedly putting in the wrong password for the lock screen, follow this help article to unlock it again:
Forgot passcode or device disabled

How to deploy a Webapplication on WAS more than one times on same server?

Hi all,
I 've a special problem:
In our web-app (some DC's) also stored propertie-Files. Now we would to deploy this application more than one times at same server using different WebContentRoots. (f.e. http://server/app1 and http://server/app2 a.s.o.)
We know, that we must create different EAR-Projects and refer the web-Module and configure the application.
But in the second application there it's recommended to change some properties.
How we can handle this in JDI without copy the web-application?
I hope my question can be understood.
Best Regards
Sven Rickelt
Using Netweaver + WAS 6.40 2004 SP 13

Hi Sven,
as I'm new to NWDI, I cannot give you a 100 percent, field-tested solution. But have you already thought about using the Configuration-Adapter?
If you can change the source of your web-app, you could maintain the data formerly stored in property files using the configuration adapter of visual administrator. The SC <a href="http://help.sap.com/saphelp_nw04/helpdata/en/45/e7e14b517b42788a1c166f9f32455e/content.htm">configuration</a> allows you to access this data.
With this approach you can stick to one web-application and do the configuration work separately for each deployed application.
Best regards,
Frank

Not able to load pages more than 3 times continuosly

Hi
JDeveloper 11.1.1.6, BPM/SOA 11.1.1.6, WLS 10.3.6, Database : MS SQL Server 2008 R2
I am not very sure if it is related to BPM or ADF, but it looks more like an ADF error..
We have a BPM process with some human tasks. The human tasks pages are ADF pages.
The pages / user tasks are opened properly for a few times, but does not load after that, until we close all the browser windows.
I am getting these errors intermittently whenever I try to open a human task page in the BPM Workspace.
(Common observation is that for the first few times the pages open properly. After more than 3+ times of opening the same task repeatedly, I a getting these 2 errors).
The page stops rendering after the last text '<div' tag.
Following are the 2 exceptions we see in the logs of the server.
We are using MS Sql Server 2008 R2 for database.
I tried with both Type 4 XA and Non XA versions of the JDBC Connections, but still getting the same error messages.
Can anyone please let us know if we might be missing anything.
Thanks for any help.
Sameer
Exceptions
####<Nov 1, 2013 12:32:34 PM EDT> <Info> <JDBC> <localhost> <BPM_MY_server_2> <[ACTIVE] ExecuteThread: '12' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <6e6476ca04c34712:23175e39:14213d8a6b8:-8000-0000000000025615> <1383323554494> <BEA-001128> <Connection for pool "MYDS" has been closed.>
####<Nov 1, 2013 12:32:34 PM EDT> <Info> <JDBC> <localhost> <BPM_MY_server_2> <[ACTIVE] ExecuteThread: '12' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <6e6476ca04c34712:23175e39:14213d8a6b8:-8000-0000000000025615> <1383323554497> <BEA-001128> <Connection for pool "MYDS" has been closed.>
####<Nov 1, 2013 12:38:37 PM EDT> <Info> <ServletContext-/workflow/MYProcessesUI> <localhost> <BPM_MY_server_2> <[ACTIVE] ExecuteThread: '2' for queue: 'weblogic.kernel.Default (self-tuning)'> <E5OI> <> <6e6476ca04c34712:23175e39:14213d8a6b8:-8000-0000000000025eec> <1383323917256> <BEA-000000> <JspServlet error: Servlet unable to dispatch to the following requested page: The following exception occurred:oracle.jbo.common.ampool.ApplicationPoolException: JBO-30003: Application pool com.dso.publicModel.applicationModule.CostReportInstanceAMLocal fails to check out an application module due to the following exception:>
####<Nov 1, 2013 12:38:37 PM EDT> <Error> <HTTP> <localhost> <BPM_MY_server_2> <[ACTIVE] ExecuteThread: '2' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <6e6476ca04c34712:23175e39:14213d8a6b8:-8000-0000000000025eec> <1383323917268> <BEA-101017> <[ServletContext@1068542008[app:MY module:/workflow/MYProcessesUI path:/workflow/MYProcessesUI spec-version:2.5]] Root cause of ServletException.
java.lang.IllegalStateException: Attempt to validate an already invalid RegionSite:
                at oracle.adf.view.rich.component.fragment.UIXRegion$RegionSiteImpl.validate(UIXRegion.java:993)
                at oracle.adf.view.rich.component.fragment.UIXRegion$RegionContextChange.doChangeImpl(UIXRegion.java:1198)
                at oracle.adf.view.rich.context.DoableContextChange.doChange(DoableContextChange.java:91)
                at oracle.adf.view.rich.component.fragment.UIXRegion._beginInterruptibleRegion(UIXRegion.java:693)
                at oracle.adf.view.rich.component.fragment.UIXRegion.encodeBegin(UIXRegion.java:283)
                at javax.faces.component.UIComponent.encodeAll(UIComponent.java:929)
                at org.apache.myfaces.trinidad.render.CoreRenderer.encodeChild(CoreRenderer.java:406)
                at oracle.adf.view.rich.render.RichRenderer.encodeChild(RichRenderer.java:2633)
                at org.apache.myfaces.trinidad.render.CoreRenderer.encodeAllChildren(CoreRenderer.java:421)
                at oracle.adfinternal.view.faces.renderkit.rich.PanelHeaderRenderer.renderChildrenAfterHelpAndInfo(PanelHeaderRenderer.java:542)
                at oracle.adfinternal.view.faces.renderkit.rich.PanelHeaderRenderer._renderContentCell(PanelHeaderRenderer.java:1067)
                at oracle.adfinternal.view.faces.renderkit.rich.PanelHeaderRenderer.renderContentRow(PanelHeaderRenderer.java:490)
                at oracle.adfinternal.view.faces.renderkit.rich.PanelHeaderRenderer.encodeAll(PanelHeaderRenderer.java:231)
                at oracle.adf.view.rich.render.RichRenderer.encodeAll(RichRenderer.java:1396)
                at org.apache.myfaces.trinidad.render.CoreRenderer.encodeEnd(CoreRenderer.java:341)
                at org.apache.myfaces.trinidad.component.UIXComponentBase.encodeEnd(UIXComponentBase.java:767)
                at javax.faces.component.UIComponent.encodeAll(UIComponent.java:938)
And
[2013-11-01T12:17:08.807-04:00] [BPM_MY_server_2] [NOTIFICATION] [J2EE JSP-00008] [oracle.j2ee.jsp] [tid: [ACTIVE].ExecuteThread: '2' for queue: 'weblogic.kernel.Default (self-tuning)'] [userId: sdarbha] [ecid: 6e6476ca04c34712:23175e39:14213d8a6b8:-8000-0000000000023fb4,0] [APP: MY] unable to dispatch JSP page: The following exception occurred:.[[
JBO-30003: Application pool com.dso.publicModel.applicationModule.CostReportInstanceAMLocal fails to check out an application module due to the following exception:
java.lang.ClassCastException: weblogic.jdbc.wrapper.PoolConnection_weblogic_jdbc_sqlserverbase_ddah
                at oracle.jbo.server.OracleSQLBuilderImpl.setSessionTimeZone(OracleSQLBuilderImpl.java:5533)
                at oracle.jbo.server.DBTransactionImpl.refreshConnectionMetadata(DBTransactionImpl.java:5311)

Hi,
depends on whether you control the BPM task flow or not. If you do, have a look at this thread for how to debug the problem
How to debug "Attempt to validate an already invalid RegionSite"?
Otherwise, post it to the SOA forum if this is initiated by their generated code. The most common reason though is that the task flow lacks a default activity. So if the default activity is somewhat calculated dynamically in your application then this may be a reason
Frank

Wrong pass word entred more than 10 times.

Similar Messages

Maybe you are looking for