WRT54G wrong input port?

When I configure my Linksys WRT54G wireless router with my cable modem the easy networking setup can't find an internet connection. Now this is only when I plug the cat 5 cable from the cable modem into the "input" of the wireless router. Now if I plug that same wire into any of the four "outputs" then it'll work just fine. I am trying to share cable modem internet service with two laptops wirelessly.
Any suggestions? I haven't updated the firmware yet, but I will look into when I get home from work.

dont plug it into your output, its bypassing all the security a router provides
you need to plug it into your input, and go into your router console, and make sure its establishing a IP address through the input.. you may have to enable "obtain ip address via dhcp"
if it is obtaing a ip via dhcp, and shows you have an ip, gateway, and DNS, then you need to go into your NIC card settings, and make sure its obtaining a IP address from your router... if its not, then you need to enable dhcp broadcasts within the router
if it is obtaining an ip address form the router, make sure the DNS is 192.168.1.1 (your router address)... if it is, and its still not working, then set a static ip address to your computer, and set your DNS as the DNS listed in your router's console

Similar Messages

How to change audio port output to input port on mac os x 10.9.2 to connect electric guitar on macbook pro for garageband

How to change audio port from output to input port so that i can connect my electric guitar to play along with garageband. I couldn't the option to change it in my system preferences of sound as my mac os x is 10.9.2. So please help me!!!!!!!!!!!! I want to play electric guitar with my garageband so badly!!! :O
Mac os x 10.9.2. ; Garageband 10.0.2

There is no audio line input on your Mac, get a USB interface, get one that is specified for guitars.

Same SQL Statement Works in Data Service but not in its Input Port

Hi Experts,
I am using this query in one of my data service. Test execute success which returned:
                                        E      U      H     M      L
2     Less Than 1 Week     0     0     0     0     0
3     1 - 2 weeks          0     0     0     0      0
4     2 - 4weeks          0     0     0     0      0
5     More Than 1 Month     0     0     6     0     0
However, when i copy the same query to the input port, enclosing it with "[my query]"
Deployed and run it. I get an "Unspecified Error" message box prompted in the iView, and null pointer exception error in the log file.
#1.5 #001A64CA3F5600660000034400001140000487DBB6D27A4D#1275277641800#com.sap.portal.visualComposer_NWBIKit_logger#sap.com/irj#com.sap.portal.visualComposer_NWBIKit_logger#TOMAS004#89896##n/a##37c590906c6711df8503001a64ca3f56#SAPEngine_Application_Thread[impl:3]_32##0#0#Error#1#/System/Server#Java###null
[EXCEPTION]
#1#java.lang.NullPointerException
     at com.sap.portal.guimachine.bikit.query.relational.impl.BIRelationalQuerySql.processTemplateParams(BIRelationalQuerySql.java:40)
     at com.sap.portal.guimachine.bikit.query.relational.impl.BIRelationalQuerySql.<init>(BIRelationalQuerySql.java:31)
     at com.sap.portal.guimachine.bikit.query.relational.impl.BIRelationalFactory.newRelationalQuery(BIRelationalFactory.java:59)
Any idea what is the mistake?
Thanks in Advance,
Sarah

Hi Experts,
I am using this query in one of my data service. Test execute success which returned:
                                        E      U      H     M      L
2     Less Than 1 Week     0     0     0     0     0
3     1 - 2 weeks          0     0     0     0      0
4     2 - 4weeks          0     0     0     0      0
5     More Than 1 Month     0     0     6     0     0
However, when i copy the same query to the input port, enclosing it with "[my query]"
Deployed and run it. I get an "Unspecified Error" message box prompted in the iView, and null pointer exception error in the log file.
#1.5 #001A64CA3F5600660000034400001140000487DBB6D27A4D#1275277641800#com.sap.portal.visualComposer_NWBIKit_logger#sap.com/irj#com.sap.portal.visualComposer_NWBIKit_logger#TOMAS004#89896##n/a##37c590906c6711df8503001a64ca3f56#SAPEngine_Application_Thread[impl:3]_32##0#0#Error#1#/System/Server#Java###null
[EXCEPTION]
#1#java.lang.NullPointerException
     at com.sap.portal.guimachine.bikit.query.relational.impl.BIRelationalQuerySql.processTemplateParams(BIRelationalQuerySql.java:40)
     at com.sap.portal.guimachine.bikit.query.relational.impl.BIRelationalQuerySql.<init>(BIRelationalQuerySql.java:31)
     at com.sap.portal.guimachine.bikit.query.relational.impl.BIRelationalFactory.newRelationalQuery(BIRelationalFactory.java:59)
Any idea what is the mistake?
Thanks in Advance,
Sarah

Please help! Not able to set Video input Port(S-Video or Composite)on Linux

Hi
I am using JMF2.1.1e(Linux performance pack) for video capturing on Linux OS. I want to set video input port(S-Video or composite) through my application. I am using the following code:
     if ( dataSource != null )
          arrControls = dataSource.getControls ();
     if ( arrControls != null )
          nCount = arrControls.length;
     System.out.println("No. of Controls: " + nCount);
     for ( i = 0; i < nCount; i++ )
          if ( arrControls[i] == null )
               continue;
          if ( !(arrControls[i] instanceof Control) )
               continue;
          componentControl = ((Control)arrControls).getControlComponent ();
          System.out.println("ComponentControl : " + componentControl);
          if ( componentControl == null )
               continue;
But, i am getting No. of Controls: 0 (Zero). So i am not able to get any control component also. Rest of the application is working fine. Please help me solving this problem.
Thanks in advance.

To go a stage further.
Google run a Jabber server for their service.
Jabber apps (those that can) use a Protocol called Jingle to make the A/V connections.
Google's version is not even that compatible with other Jabber apps. (See Here)
The Plug-in in the Google Install (Or the Standalone Web Browser Plug-in allow Browsers to access the GoogleTalk A/V side as does the Standalone PC app called GoogleTalk as well.
iChat uses a process called SIP (Session Initiation Protocol) to connect to other iChat Users or to the AIM for PC app.
However this also works in any iChat to iChat Connection no matter if the Buddy List is an AIM Login based one, Jabber (including GoogleTalk) or A LAN based Bonjour Chat.
In you care this is not going to work.
Getting the Standalone (Intel only) Browser Plug-in and using the Chat option in the Google Mail Web page is probably the easiest option.
7:31 PM Friday; January 7, 2011
Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"

Would connecting the HDMI port of my 15 Macbook Pro Retina to the DVI input port on my Dell UltraSharp 2434 LED HD Monitor work?

Would connecting the HDMI port of my 15 Macbook Pro Retina to the DVI input port on my Dell UltraSharp 2434 LED HD Monitor work?

Hi Wizard0705,
If you have questions about connecting an external display to your MacBook Pro, you may find the following article helpful:
Apple Support: How to use multiple displays with your Mac
http://support.apple.com/kb/HT5019
Regards,
- Brenden

G4 and microphone suitable for sound input port

I'm looking into getting started with podcasting and I need help with selecting a microphone. I'm on a G4 desktop machine with a sound input port, any suggestions as to the tech spec or manufacturer of a suitable microphone would be most appreciated.
Thanks.
G4 desktop Mac OS X (10.4.6)

Hi, Neil -
This Apple KBase article provides some info with regard to microphone selection -
http://docs.info.apple.com/article.html?artnum=18275
Scroll down the article to the G4 section that matches your G4 model.
Many users have gone to using the Griffin iMaic adapter, since it permits a wide variety of micophones to be used. There's a link near the bottom of the above article to Griffin's iMic page.

How to submit data from multiple Input Ports in single SUBMIT button click

Hi,
I am in SPS8.
What exactly steps I need to perform to submit data from multiple Input Ports.
I couldn't able to submit One input Form and one Input Table to BAPI data service in single SUBMIT button click.
I debugged the VC application in SPS8.
While debugging, I found that when I click the SUBMIT button in the Input Form, Only data in that Input
form are being passed to the BAPI, But not the Table Form data.
If I click on the SUBMIT button in another Input Table, Only data from that table is being passed to the BAPI, but not the Input form data.
Essentially I need to submit both of them in one SUBMIT button.
Thanks,
Ramakrishna

Ramakrishna,
From the word document that you sent to me the steps you are missing to map the appropriate information into the BAPI is first you are not mapping all data rows into the table input port. To do this double click on the input table view and change your selection mode from single to multiple. Then when you click on your link between the BAPI and your input table you will see a new option appears under data mapping "Mapping Scope" select All Data Rows.
That's the first part of the problem to get the BAPI to recognize both the inputs coming from the form and the table eliminate the submit button from the form. Drag and drop a link from the output port of the table view to the Input port of the BAPI. Double click on the link between the BAPI and the table view and open the expressions editor for the two fields:
1/ Automatic Source
2/ SKIP_ITEMS_WITH_ERROR
On the hierarchical folder structure on the right expand expand the Data Fields node to find the fields from the form and map them accordingly.
Now when you hit the submit button on your table it should pass the BAPI all the parameters from both the form and the table.
Hope this helps,
Cheers,
Scott

HT4619 How to test the audio input port

How do you tell if the Audio in port is functioning. I have tried everything and cannot get the computer to accept audio from the external mic. or guitar.

The audio input port is line-level and will not pickup the week signal from an un-amplified mic or guitar pickup.
To test the audio input, try an iPod, stereo receiver or something that has a built in amplifier.
To use an un-amplfied mic or guitar, you will need something like a > MXL iBooster or a USB > Griffin iMic.

Sysgen : How to read the input port data type, width and rate dynamically in a masked subsystem ?

Hello everybody,
     I am designing a general purpose block in system generator. I pass the user parameters to the block through masking it. Some user parameters can change the block configuration. The input port data type, width and rate can also affect the block configuration.
     The problem is that these values (input port data type, width and rate) are subject to change. So I should read them dynamically, then change the block configuration through programming the "Initialization Commands" field. But unfortunately there is no straight way to read the input port information.
     There are some methods in for example the "Black Box". these are:
input_width = this_block.port('din').width;
input_rate = this_block.port('din').rate;
But these methods are not applicable to a masked subsystem.
I have tried other ways also. You can find them below. None of them worked.
Does anybody know how can I solve this problem?
Other ways I tried:
1)
design_name([],[],[],'compile')
q=get_param(gcb,'PortHandles');
get_param(q.Inport,'CompiledPortDataType')
get_param(q.Inport,'CompiledPortWidth')
get_param(q.Inport,'CompiledPortDimensions')
design_name([],[],[],'term')
2)
ssGetInputPortDataType
3)
ts = Simulink.Block.getSampleTimes([gcb '/Input'])

Today we rely on Simulink to perform parameterization of your designs in two ways:
Parameterizable Subsystems and Blocks : Parameters themselves can be MATLAB expressions that need to be evaluated for which we need the MATLAB interpreter
The very useful Rate and Type propagation or Simulink compilation that allows us to specify types & rates in one location that gets systematically propagated to all.
To truly make the HDL Netlist that is generated from SysGen parameterizable, we would have to implement some of this capability in the HDL netlist itself by:
Using Generics(VHDL) or Parameters(Verilog) - We would have to capture the bit width(type) propagation through levels of hierarchies and finally parameterize the IP itself based on this value
Since IP itself does not have this capability through generics, we would have to package a separate tcl script that updates the IP parameterization appropriately in response to top level parameters(or GUI parameters)
Interpreting MATLAB expressions and translating them into VHDL/Verilog expressions (alternatively tcl expressions of IP). In simulink, mask parameters can be passed from one level to the next. Also parameterization of a block can be composed of Matlab expressions using variables from ancestor masks & the MATLAB interpreter – so we will need to somehow capture that as well.

Multiple Input Ports on BAPI to submit at the same time

Hi
I have looked at previous threads and still not getting this right. When I click the submit button I need it to all go to the BAPI at the same time.
I'm using BAPI SalesorderCreatefromdat2, I need to use at least three input ports.
I have done the following.
-dragged the bapi on the page
-selected the ports required, flipped a port of required
-the for ports I have created 1 form (Order Headr I n Port), 2 tables (Order Itmes In port, Order Partners Port).
-the have connected the form and tables to the bapi, so have three different lines.
-For each one the eventname is *SubmitAll
-Then there is one button,on the action tab I selected custom action,the name is SUBMITALL, Apply To is Self
Is the above correct??
Please let me know, thanks in advance

Hi Basheer
Thank you for your reply.
I have changed the buttons to Action Type "System Action", the field System Action to "Submit Form", the Apply To is "Self"
I however get the error "Please enter sold to party or ship to party"
Can you please help me. I have changed my BAPI to use SalesorderCreatefromdat1 like yours.
I'm using the following input ports and fields
-Order Header in form, using fields DISTR_CHAN, DIVISON, DOC_TYPE, SALES_ORG
-Order Partners Table in table, using fields PARTN_NUM and PARTN_ROLE
-Order Itmes Table in Table, using fields MATERIAL and TARGET_QTY.
Is this correct? Thank you for the response.

Multiple Input ports - Single Form

Hi,
I have a RFC which has multiple input ports. How do i use a single form to provide data to all the input ports.
Regards
Bharathwaj

Hi,
you can create the single form direct, if you pull a line out of the RFC, then the form must be created with the fields. If not, then you have to create it manually and map the fields with the input port.
Best Regards,
Marcel

How read from the HDMI Input Port?

Pulling down the Add Media menu in my Premiere Elements 11 window, I do not see an HDMI port input.
My Dell XPS ONE PC (running Win 8.1 Pro) has an HDMI Input port.
I would like to pull audio/video off this port into Premiere Elements 11 to edit and save to a disk file.
Any ideas on this?
Thank you!

AT,
Thank you for your reply.
First to comment on DV, HDV data capture. Yes, reading Adobe documentation I see the Premier Elements data capture works with Firewire.
For example, one Adobe document is at:
http://helpx.adobe.com/premiere-pro/using/setting-system.html
The HDMI port in this diagram is an output port on the camcorder and connects to a TV set. That way the user can monitor the data capture in progress.
I suspect that most PC's and laptops, like the DV/HDV camcorder labeled with letter "D." in the Adobe diagram have an HDMI output port only. The intent is to put the screen or video content out to an external TV.
Some PC's now, as does my Dell XPS, include an HDMI input port. It is connector # 15 on the diagram for the XPS at
ftp://ftp.dell.com/Manuals/all-products/esuprt_desktop/esuprt_xps_desktop/xps-one-27-2710- aio_Setup%20Guide_en-us.pdf
To make my post brief and concise I purposely left out any detail about the input device. I believe HDMI stands for High Definition Multimedia Interface. I want to assume some high definition (and therefore high speed) digital data stream accompanied by a digital audio stream is coming into the PC. Whatever HDMI supports, the HDMI hardware on the PC input port should handle.
As one example, I should be able to play a file from my DVR into the PC over the HDMI input port. This might be a saved TV show or a clip from a DV/HDV camera recording.
That's just an example. But, what I am trying to do is recover the video/audio off an old Samsung SCL901 Hi8 camcorder. I was asked and I told my acquaintance I would try.
The camcorder interface is the legacy S-video port. A second audio port (3.5 mm female jack) carries (as you know) only mono audio (left side in the stereo cable).
One thing to do is to play the camcorder Hi8 tape into my DVR. The DVR has a legacy S-Video port and phono plugs for the audio right in the front panel. Then burn a DVD. Then put the DVD in the PC, read it into Premier Elements and edit the material.
Instead, what I'd like to do is play the tape right into the PC. There seems to be a lot of legacy media that folks have just let sit around way too long. And now the world has passed them by. Enough people that apparently some companies have built converters.
I looked at this S-video to HDMI converter.
http://www.walmart.com/ip/Composite-S-Video-and-HDMI-to-HDMI-Converter-and-Switch-w-HDMI-P AL-NTSC-Support/39457809
This is a Roku brand S-Video to HDMI converter. It upsamples the legacy 480i to 720p or 1080p HDMI digital signal.
The Roku converter appears to get the S-Video into the PC hardware. Then what?
It was sort of wishful thinking pulling down the “Add Media” menu tab in Premier Elements 11, wanting to read from the HDMI Input port.
Still, Adobe does magical things, so I thought I would ask in this forum.
So “Yes” to your add-on question at the end of your post. I was thinking of capture via HDMI. And I agree with your first impression that this is not possible.
It could be there is software available from somewhere that will dump the HDMI port on the PC directly into an AVI, MOV, Microsoft, Flash, mpeg, DVD or some other standard file format. Then Premier Elements can open the file for further editing.
AT, I appreciate your response and comments on this project. They have been useful guides. Thank you so much for your time.
JB

Problems configuring a port in niPXI-6509 card as input port using static DIO Register Level Programmer maual

Hello ,
I am using a ni PXI-6509 card for my application. Since I have to compile my application in Interval Zero RTX, I am using the static DIO Register level programming using VISA. I have successfully configured the card to do output on port0. But when I attempt to comfigure another port1(not the same as output) I can successflly configure it. But when I send 5V through the corresponding pins I donot get a value 1 in the Data register for that channel.
the following i did to configure as Input...
1) IO Select register set to 0 (for input as the manual suggests)
2) read from IO data register.
Do I need to do anything special to configure as input port.
please suggest...
Thanks
Kuchi

Hi Sathish,
Given how much blatant, undisclosed, and unrepentant
cross-posting [1] [2] [3] [4] [5] you've done to ask this question, I
gave you the benefit of the doubt that you were new to the NI forums
and didn't understand the etiquette of this community. However, looking
at your profile, you've been around just over 8 years! How can you be
so selfishly impolite?
To your credit, you at least searched the forums to find (somewhat) relevant to which topics to reply, but as you said you 'tried the entire NI Site', I'm surprised that you missed the DDK home page [6] that has a link to the M Series register map.
[1] Re: m series register programming in straight C
http://forums.ni.com/ni/board/message?board.id=90&message.id=1644#M1644
[2] Re: Problems configuring a port in niPXI-6509 card as input port using static DIO Register Level Programmer maual
http://forums.ni.com/ni/board/message?board.id=90&message.id=1645#M1645
[3] Re: Problem with writing to registers
http://forums.ni.com/ni/board/message?board.id=90&message.id=1646#M1646
[4] Re: Is there a Register Level Programming manual for NI 625x PXI
http://forums.ni.com/ni/board/message?board.id=270&message.id=7661#M7661
[5] Re: Where Can I find information about register level programming the PXI 6259?
http://forums.ni.com/ni/board/message?board.id=250&message.id=53551#M53551
[6] Register Level Programming for OEM Customers
http://digital.ni.com/express.nsf/bycode/exyv4w?opendocument
Joe Friedchicken
NI VirtualBench Application Software
Get with your fellow hardware users :: [ NI's VirtualBench User Group ]
Get with your fellow OS users :: [ NI's Linux User Group ] [ NI's OS X User Group ]
Get with your fellow developers :: [ NI's DAQmx Base User Group ] [ NI's DDK User Group ]
Senior Software Engineer :: Multifunction Instruments Applications Group
Software Engineer :: Measurements RLP Group (until Mar 2014)
Applications Engineer :: High Speed Product Group (until Sep 2008)

Input port BAPI

Hello,
Can anyone tell me how to use BAPI's that have no input port, in the Visual Composer?
For example BAPI_OPPORTUNITY_GETDETAILMUL?
This BAPI has only output ports.
What scenario's/situations is such a BAPI useful in the Visual Composer (and how)?
Kind Regards
Murat

Hi Murat,
If the BAPI do not have input ports it should means you will get an output by default because it runs with an fix input, have you tried how it works in runtime ?
i.e: create an iView with this datasource and with some table as output... or just run the Test Datasource to see how it return the data
Best Regards,
Luis

Wrong input, new 3d card

Hi. I was going to install ati radeon 9200se on my computer. But when I plug it in det screen turns black after windows loading, it says: wrong input or something. How can I get it to work?

I don't know what your old card was but put it back in. Uninstall the drivers belonging to it from within the OS. Shut down. Install your new card. Should work. If not, see if you can get into safe mode (F8) and install new drivers there.

WRT54G wrong input port?

Similar Messages

Maybe you are looking for