X-Fi Elite Pro no wave support in XP Media Cente

I no longer have my original installation CD. I downloaded the latest drivers from the site for Media Center 5 and they installed without any error messages. I don't get any sound. It shows the X-Fi as properly installed in device manager. I have disabled the Audio on my motherboard. If I open the Sounds and Audio Device Propeties dialogue box in Control panel under the Audio tab for Sound Playback it says there is "No Playback Devices". Under Midi music playback it does show "SB X-Fi Synth A [BC00]"? If I go to the hardware tab it shows the Creative SB-X-Fi under devices which if I open and click on the properties tab it shows Audio Devices, MIDI Devices and Instruments and Mixer Devices. If I double click on Creative X-Fi Audio Processor (WDM) the properties dialogue box opens which states the statas as: Driver is enabled and functioning properly. It seems to be installed properly but it is not available for wave audio.

I have checked, doublechecked and triplechecked the mixer settings,
and digital io only is switched off.
I've tried using the speaker connectivity wizard, but no luck....
Message Edited by JudgeHwak on 0-24-2005 0:56 AM

Similar Messages

Apple 23" Cinema Display not supported by Windows Media Center Edition PC

Well I'm learning the hard way and of course that is through experience. I just found out after purchasing my 23"Apple Display and talking to the Apple Support Tech is that Apple does not support the Cinema Display with PC's,
Wish Apple would be more transparent on this issue prior to a costly purchase. For example on the Apple site listing the Display in system requirements:
Windows PC and graphics card that supports DVI ports with full single-link digital bandwidth and VESA DDC standard for plug and play setup
Well I have a Windows PC with a Nvidia Graphics card just as the system requirements state. Yet my PC will not adjust to proper resolution for the Apple Display. The graphics card works fine. Its a driver issue where the Apple Display is not compatible with Window Media Center Edition on Windows PC's
So in conclusion the system requirements for Windows PC's that Apple is stating For Apple Cinema Displays is not correct. The system requirements need also to state that the Apple Cinema Display does not work with Windows Media Center Edition (MCE)
Hope that helps for any users with Windows Media Center Edition thinking or already have purchased an Apple Cinema Display.
73,
John
Mac Pro 2.66 GHZ, 1 GB RAM, 250 GB HD Mac OS X (10.4.7) Sony Vaio Desktop PC, G-Drive External HD,Toshiba Satellite Pro Notebook

Well,
Here is the latest from Nvidia Customer Care educating users on the DVI port on the Nvidia GeForce FX 5200:
"...The basic difference you will see in these ports are in their Physical appearance. The DVI-D has less pins compared to the DVI-I port connector. Also the Apple 23" Cinema Display will work at a resolution of 1920*1200. But this graphics card that is Geforce FX 5200 will not support this resolution of 1920*1200. It will support only till 1600*1200. So that's the reason you were having the issues were you were not able to adjust the resolution"
So I ask, which Nvidia GPU card can I substitute for the current one at a reasonable price? I don't need dual link, so single link would be sufficient for my application . Here is some more helpful tips from Nvidia support. Hope this helps other users, utilizing the Apple 23" Cinema Display"
"...go for a Geforce 7600 GS graphics card which is a AGP 8x compatible graphics card. This graphics card is just 129$ graphics card. Please visit the given link to know about the details of this graphics card."
http://bfgtech.com/7600GS_512.html
And now for the final conclusion of what you need to know regarding DVI ports. Evidently Nvidia uses a term called normal DVI port. I've never heard of that term in the literature in shopping for a graphics card and checking the specs. I guess you need to look for the specific term single or dual link specifically. If it doesn't say that, then what I can gather it is a normal DVI port...whatever the heck that is?
"...Yes let me inform you that the Geforce FX 5200 graphics card does have one DVI port and one VGA port. But these single link and Dual link DVI port is totally different compared to the normal DVI ports. As you wanted to connect an Apple 23" Cinema Display to this graphics card. So for this you will need to have a graphics card which will have a Single link or Dual link DVI ports not the normal ports. So to support an Apple 23" Cinema Display, you will need to have either a Geforce 6 series or the Geforce 7 series graphics card. That's the reason I gave you the list of graphics card which comes with Single or Dual link DVI ports, not the normal ports."
Oh well off to the market to pick up either a Series 6 or Series 7 Nvidia Graphics card. The Nvidia Customer Care team was very helpful and replied to my inquires very quickly through email.
Hope this long drawn out expose helps others who might have issue with connecting their proud Apple 23' Cinema Display to their PC
Kind Regards,
John
Mac Pro 2.66 GHZ, 1 GB RAM, 250 GB HD Mac OS X (10.4.7) Sony Vaio PC, G-Drive External HD,Toshiba Satellite Pro Notebook

X-Fi Elite Pro: Implementation of Effects in M

Hi
Can someone please help me here? It's quite urgent.
I only just switched over to X-Fi from SB Li've yesterday. I'm missing a few things which IMO shouldn't be this difficult to find. If the manuals were printed, they'd basically be good for nothing more paper weights so I do hope someone here will be able to assist me.
Before I start I should probably mention that I'm in Audio Creation Mode.
. EAX presets: When I open the EAX controls in the Audio console, there are no presets plus the preset window is blanked out. The help file says that one should select a preset from the list but given the afore mentioned info, this proves to be somewhat impossible. How do I make the preset window acti've and get presets into it's
2. Auxiliary Effects:
a. In the SB Li've's EAX controls, one was able choose with which MIDI controller to send triggers for EG. a Multi-Tap Echo. If I understand it correctly, the MIDI implementation chart in the manual (which I stumbled upon by accident) seems to indicate that Auxiliary effect 3 is triggered by Controller 92 and Aux 4 by controller 94. However, I get zero response from either Auxiliary when triggering either of the 2 controllers. How do I trigger Aux effect 3 & 4 from my sequencer? Also I don't get any response from Aux 3 & 4 on the Wave channel of the mixer.
b. Is there a better delay unit than the "Digital Delay"? The fact that Tap can only go to 207milliseconds and Tap2 to only 404milliseconds, makes it totally useless for a /4 note echo of anything slower than 48.5BPM. The SB Li've's Multi-tap used to be able to go into the thousands. I'm unable to hear what it sounds like since I can't get Aux 3 & 4 to work.
I hope someone will be able to help me.
Thanx in advance

Hi
Pardon me if I seem a little sinical in this post. It's just that I don't like buying a new and expensi've piece of equipment and having to do a runaround trying to fix problems which shouldn't have been there in the first place.
It's a pitty that problems one has with a new piece of equipment or software almost always is fixable with something that would appear to be user incompetance when in fact it's the result of poor documentation. Anyway, thank you to the support team who helped me out. It would have been nice, though, if my more specific issues were answered concisely and not left completely unanswered.
I thought I'd post the solution if someone could benefit from it:
If you had previously run a Sound Blaster Li've! Platinum before installing X-Fi Elite Pro and you find that Auxiliary effects 3 & 4 doesn't work, it's likely that some of the previous SB Li've drivers had not been completely removed from your system. To do this you have to do a clean sweep of your previous installation (which I would have though should be handled by the uninstall program). Anyway, here's a link to a support page which describes how to accomplish this:
http://us.creative.com/support/kb/article.asp?l=3&sid=72
and then click on the appropriate link.
One problem I had is that the CTZAPXX.EXE mentioned in the procedure doesn't appear on the driver disk that came with my SB Li've! Platinum. Fortunately I have a SB Li've 24bit as well and the app was on that driver disk.
After going through the procedure as mentioned above, the 2 Auxiliary effects still did not work. I then installed the new drivers (Update 4) as available on Creative's Driver Page on 2 Dec 2006. At last it worked. A word of caution: Make sure you exit the Creative Volume Panel before installing Update 4. Otherwise, nothing will work as it should.
OK so that fixed my auxiliary effects not working.
I had to answer my MIDI controller question myself by testing with 0-27 values as the reply from support ignored this question amongst others completely. In all fairness, though, the MIDI implementation chart did tell me where to start the trial and error and reduced the test time considerably. And here's the result: Controller 92 does in fact control the strength of Aux 3 and Controller 94 controls Aux 4. There, that sentence took me like what? ...0 seconds to write.
That leaves my other 2 questions:
. Where has the presets gone under the EAX tab of the Audio Console when in Audio Creation Mode? There are 7 or 8 of them in Game mode but only a blanked out window in Audio Creation Mode.
2. Is there a better delay unit available anywhere which allows for longer delay times. The current one is actually closer to a reverb unit than a delay unit as there are many reverb units with longer delay times than this.
OK, so enough raving. Thanx for the help from support.

Elite Pro and vista, creative console resets after ever reb

So, I've given up trying to search for the answer and I have no clue how to go about fixing this problem.
If I boot into visata 32 Ultimate, and go and setup my audio console the way I like it then reboot, it will reset itself to defaults when I boot back into windows.
basically its not saving my configuration. Why does this happen and how can I fix this? It doesn't sound the same as the Digital output resetting itself. I have the latest drivers installed on a clean slate...why does this still happen?
its friggen annoying!

yep , i see they are supported, the same is mentioned on the drivers download page,
it states that DTS has been re enabled on devices that supported it on XP when they were originally released.
so i have the elite pro, wich supported dd and dts, and still i get no sound form any dvd in dts or even sound from my PS3 input via optical to the external I/0 of the elite pro.
and i have been told that i would need to buy the dts pack.
why ? when i already paid ?250 for the card that supported it from the moment i bought it ?
dts input support was one of the reasons i bought this card in the first place.
i might as well sell this and use my onboard optical output and buy an amplifier that supports dts, at least then ill know that there are no drivers/support problems
?creative you might make the best sound cards out there but that alone only gets you half way there. us customers we need support and value for our money?
not u trying to rip us off
Message Edited by dkbimo on 07-0-2009 03:57 PMMessage Edited by dkbimo on 08-4-2009 05:9 PM

X-fi elite Pro Driver for Windows 7 64bit

)X-fi elite Pro Driver for Windows 7 64bitH Hi all
I've read in the past and toady some topics about the x-fi drivers and windows 7.
Due to the fact, that I want to install win7 64bit in the next few days, i just want to know which drivers I should use for my Elite Pro.
Currently I'm using XP and got no problems with the drivers yet, everything could be installed with the cd from my elite pro package.
So as far as I understood the topics correct, there are 3 option which drivers i could use:
. Orignal Creative windows 7 driver
2. Daniel_k support pack
3. Pax drivers
Can anyone tell me the advantages or disadvantages of these drivers? Important for me are the "gaming" utilities and THX for my 7. Teufel system.
Which dirvers should i use and work without problems?

- i have? windows 7? 64 bit
? and having trouble with an older version
? SOUNDBLASTER AUDIGY PLATINUM ex
? i cannot get it to open mixers, or other Audigy functions.
? even with downloading Windows 7 driver from Creative.
? doug barron? 902 425 8836

X-Fi Elite Pro, can't hear PS2/X

Hello. I tried to search the forums, but I either searched poorly or I couldn't find a similar issue.
Here's the problem -- I can't hear either my PS2 or my Xbox using the Elite Pro on my PC.
Hardware:
[The good part]
PC does not have on-board audio for the motherboard (no need to flip a BIOS switch).
I have the SoundBlaster X-Fi Elite Pro PCI card plugged into an open PCI slot on the motherboard.
I installed the drivers from the CD as per the instructions. After the drivers are installed, and the reboot occurs, I can hear my normal PC sound perfectly through my headphones (I only have headphones. Speakers will come later).
Initial hardware check - PASS.
[The bad part]
I plug the two RCAs (Left/Right) from my PS2 into the back of the Elite Pro exterior console.
I plug my Xbox into the back of the exterior console as well, only this time into the optical input using Monster cabling.
That's what I have set up. No matter what I've tried as far as configurations go on the software side, I cannot hear these two devices. Either through the fancy-graphics Creative Console Launcher, or from XP (SP2)'s Control Panel > Sound options... I just can't hear anything (Playback or Recording options, Mute boxes, volume sliders, etc). I've also tried flipping the Aux2/Phono switch on the back of the exterior console and then trying everything I already tried all oer again.
I'm at a loss as to why I can't hear anything. I went to the store and picked up a RCA-to-Stereo converter and plugged the PS2 into the Microphone/Line-In port on the exterior console, and I could hear the PS2 through that. There are several reasons why that is an insufficient fix to my problem: ) I'd like to hook up the Xbox and PS2 at the same time. 2) I play World of Warcraft, and need the microphone slot freed up so that I can speak to my guild, and not have to crawl behind my machine every time I want to switch what I'm doing. 3) I paid for the Elite Pro specifically so that I could set all this up.
If anyone has any suggestions, by all means let me know!Message Edited by Gimpifier on 09--2006 09:48 PMMessage Edited by Gimpifier on 09--2006 09:49 PM

Ok, as you see in the picture, there are several mixer stri
ps.
All of them are related to the upper tabs. So:
The Inputs tab bares all the available inputs on your rack and PCI card (just Line In for the latter).
The Multi-Channel Wave tab bares all the outputs available on your rack and the PCI.
Those two tabs are the most important right now.
As I noted earlier, the problem occures either from a mute selection in the Auxiliary 2 strip or a 0% setting to the volume slider of the same strip. Otherwise, you are routing the Aux2 to an output not connected to your speakers. From what I see, no "Mute On" is apparent and you are routing every input to Front L/R Output. Have you tried plugging your headphones to Front L/R and select "2/2." as speakers?
You should also select the monitoring to "Recording" and not to "Playback" (found at the blue field, bottom right). This will enable you to see the input level for your recording source (Aux2 in your case, correctly selected by you).
Your speaker selection is set to "Headphones". Are they connected to the front output?
It might be better to do some troubleshooting. So:
What is the real problem?
No signal from Aux2 input?
No signal from the headphones output?
You say that:
Gimpifier wrote:
The RCAs are li've and working. If I use the Stereo adapter, I can plug them into Mic-In/Line-In and I can hear them if I swap to Line-In. The problem is getting them to work as they are intended, so that I don't have to monkey behind the PC when I want RCA audio.
Can you be mor specific on this? Li've and working? You mean li've from the PS2? Get them to work as intended?
Message Edited by Chastity on 09-3-2006 08:46 AM

5.1 sound X-Fi elite pro and DTT3

Hi all?Ok, so I have an X-Fi Elite Pro, and the DTT3500 speaker setup from Creative. Both very expensi've where I li've. I could get 5. sound from my SB Li've! 5. digital, but no such luck on the X-FI. I've read all the posts, but when speaking to Creative tech support they tell a different story. I know I can get 5. (supposedly) from DVD etc. via co-ax or optical. How do I get 5. from other apps (such as VideoStudio) or games (BF242, etc.) that do not output DD or DTS?I've tried flexi jack to DIN (from card rear panel to the speaker amp), DIN to DIN (from break-out box to speaker amp) and 3 x 3.5mm stereo to DIN (from card rear panel to speaker amp) Nothing works. I get headphone sound obviously, and can get plain stereo sound (although I didn't get this setting right for optical; works with co-ax though)?(excerpt from tech support mail)
To assist you, i would suggest to connect the DDT3500 to the soundcard using the 3.5mm jack and the DIN Cable provided directly to the soundcard through the Digial In and DIN Socket.. enable the "Bit-Steam off" in the Audio Console, 2. select " Digital DIN" on the DTT3500 FacePlateIn case if you need any clarification, please do not hesitate to contactus.(/end excerpt)?I have made up a cable with 3 x 3.5 mm stereo jacks > DIN and got no sound at all from this. Tried all my solutions with digital I/O both on and off.?This is all very limiting, as apart from games that I'd like to enjoy as they're meant to be played, I also do video editing and need to proof my surround mixes. Not very happy Creative. Even the tech guy where I bought the card assured me it would work with 5....

I have never installed the updated applications available in the download page... just applications and driver for Vista 64bit inside the cd and i updated the driver with the latest one. Anyway, I: Reformatted and installed Vista.
Installed Chipset Drivers.
Installed Video Drivers.
Downloaded and installed JUST the latest SB drivers and i have that **bleep**-ing error window...Guys, it's 2 years i try to install Vista...Have i to destroy this sound card If i have to change it, i'll never buy another creative product in all my life (and till today i have bought 3 sound cards, 2 webcam, 4., 5. and 2. speakers for every computer we have in the office...). Thanks p.s.What is the DMLL.exe service, please
If i enter in the "Task Bar" is visible... if i close it and i restart the computer i find it... How can i delete it forever

Vista 64, Latest Driver & X-Fi Elite Pro: Audio issue with Pro Evolution Soccer 2008 (Pes 20

Hi,i have formatted XP S.P.2 and now i'm using Vista Ultimate 64.I have got an X-Fi Elite Pro and i have installed all the applications using the CD-Rom.I updated the driver, Alchemy and Mediasource to the latest version.The system is totally clean and updated (I used Windows Update when i finished to install Vista and nothing was installed). I would like to know why i cannot play Pro Evolution Soccer 2008 like in XP: when i enter in the game i have a noise (looks like the noise of the needle in old gramophones...) and i cannot use the speakers (Creative ProGamer G500).If i turn the volume to 0 i can hear it too... i have to switch off the speakers or exit the game to delete it.Is it another bug I tried to uninstall and doing a new installation of the game but... no way men... Thanks p.s.After year and 4 months (release date of Vista) is it possible to have a decent driver... The Audio Quality in Vista Ultimate 64 bit is lower than in XP and the same wave files have distortion with the low and middle-high volume (60-70).
Problems that i have never had in XP... i cannot reinstall XP another time. I bought Vista in 2006 and i cannot use it till you'll release a good sw.
Have we to wait till 200 for a fuc.ing working driver
My Hw.: Intel Core 2 Quad 6600, DFI Lanparty DK, 2GB DDR800 Team Group, X800XT 52MB, Enermax Noisetaker 600W, Creative X-Fi Elite Pro, Creative ProGamer G500, Plextor PX76SA, Logitech G5 and G5.

The problem is now official: other customers have problems with some games (Pes 2008 and Crysis in particular). I'll show u the main italian hw. forum. There is a thread of more than 500 pages just about Creative X-Fi: http://www.hwupgrade.it/forum/showth...42043&page=550 I would like to know if u test drivers before sharing... because i don't know what you did in more than year.You should meditate, people... I paid more than 400 $ for an Elite Pro and after year and 4 month i cannot install Vista 64 too for audio issues with mp3-wave files and Pes 2008 or Vista 32 bit for problems with Pes 2008. This is my latest Creative product, you can trust.

Apple TV issue-I have a Pioneer Elite Pro 1130 with a PRO-Ro6u Media Receiver. I cannot get my new Apple TV unit to work on this TV no matter what I have tried. No Video

My new Apple TV unit (3rd generation) will not work with my Pioneer Elite Pro 1130 tv. The TV has a PRO-R06u Media Receiver. No matter what I try, I cannot get anything to come up on the screen. No Video and No Audio??

Try cycling AppleTV resolutions with the remote using the tip for 'black screen recovery' here:
http://support.apple.com/kb/ht3176
The set is quite old now, does it support HDCP?

X-Fi Elite Pro help plea

I've just got an X-Fi Elite Pro, i slotted it into a spare PCI slot and booted into Windows XP.
Windows loaded fine, I inserted the driver disk and installed all the software on it. I restarted.
I get a window pop up saying "Multimedia Audio Controller" detected. I follow the messages to automatically find and install the drivers, after a while i get a message saying "The hardware was not installed because the wizard cannot find the neccessary software."
Can anyone help me on this issue please?
My X-Fi card has the code "SB0550" written on it btw.

I've just been looking at the Device ID and the devices supported by the Creative drivers they have.
My X-Fi Elite Pro defines itself as:
PCI\VEN_0&DEV_0005&SUSBYB_002002&REV_00\4&CF8C54&0 &08F0
The hardware itself is listed as:
PCI\VEN_02&DEV_0005&SUBSYS_002002&REV_00
PCI\VEN_02&DEV_0005&SUBSYS_002002
and X-Fi devices are defined by the driver as:
%XFi.DeviceDesc%=XFi_Device,PCI\VEN_02&DEV_0005&SU BSYS_00202
%XFi.DeviceDesc%=XFi_Device,PCI\VEN_02&DEV_0005&SU BSYS_00302
%XFi.DeviceDesc%=XFi_Device,PCI\VEN_02&DEV_0005&SU BSYS_002202
%XFi.DeviceDesc%=XFi_Device,PCI\VEN_02&DEV_0005&SU BSYS_002302
%XFi.DeviceDesc%=XFi_Device,PCI\VEN_02&DEV_0005&SU BSYS_002402
%XFi.DeviceDesc%=XFi_Device,PCI\VEN_02&DEV_0005&SU BSYS_002502
%XFi.DeviceDesc%=XFi_Device,PCI\VEN_02&DEV_0005&SU BSYS_002602
It's close but not the same - so where do i get the drivers for my specific card?

X-FI Elite Pro Din connector and compatible speakers

Hi all?I?m a?owner of an X-FI Elite Pro. Amazing 55 million transistor sound?From what I can read here in the forums, I can control selected Creative speakers with the?9 pin Din cable. I?m aware of the 3 spdif signals incompatibility with this connector.
Now I?m confused some say it works others say it doesn?t work..... Which speakers are supported ? Models ? Most of them have the wired remote or control pod. Nor in the speaker manuals nor in the Elite pro manual are the compatible models listed?I want power ... so I?m interested in the Gigaworks series like the S750. Anyone tested the combination ??

Well since nobody answered today I have hooked up the Logitch Z500 Digital and the sound is just amazing. I was moving to 7. but there isn?t much offer from Creative.... and 5. is still the standard. It?s a shame that on such a quality card there are only crappy Creative 20 watt speakers for sale.

Creative X-FI Elite Pro + Windows Vista = Audiodg.exe 60%+ CPU Please He

Hi,
I got a problem with the Audiodg.exe process, problem is that sometimes it uses from 5% cpu and jumps to 50% and more and when playing this makes everything choppy and even cause mouse lagg..
As fast as i tab down the game the process drops to 5-0 and if I tab in again it jumps and holds on for several sekunds/minutes and then everything works fine and some minutes later it starts again.
This Hapends when playing all sort of games but mostly hapends in Counter Strike Source, and Windows Media Player, when watching films or listening to music but when doing that it gets worse and making the sound to lagg or slowdown etc.
Any idea got all the latest drivers exept for bios becouse Asus bios are unstable, and i cannot switch audio drivers becouse i got 4gb of ram and only the latest creative drivers work with 4gb...
Hope you understand everything
Spec:
OS: Windows Vista x64 Build Version 6.0.600 (SP ENG)
Motherboard: Asus Crosshair nForce 590sli
CPU: AMD 5200+ FX-62 Dual Core Black Edition
RAM: 4xgb Corsair Dominator 066mhz (running only 932)
Sound: Creative Elite Pro
GFX: nVidia Gainward 8800GTX
PSU: CoolerMaster Real Power 000watt
HDD: 2x Western Digital Raptors X (2x50gb)
IDE: x DVD Liteon x8 burner and x CDRW Lite On Burner x52
USB 2x USB Devices Mouse and Keyboard
Lan Ethernet cable
Lan2 Disabled
Nothing gets overheated etc...
Everything got latest drivers etc...
Hope thats all, Best Regards C0MM4NDER

I didnt have this issue before to, it just starded after my reformat when i noticed that my cpus where on 100% in a game and then noticed that it was a process called Audiodg.exe that eats everything.
Im running software from my Creative Vista CD + updates from Creative Site, (and the 10006. driver from this site.) and no no codec packs installed yet. nothing this is a clean install only standard programs running installed only nod32 creative software and defrag software. and i used this before when i didnt have this problem only new is the drivers that i NEED becouse i use now 4gbs of ram and, this is the only hardware change from format, i had 2gb then now i got 4gb and i downloaded the latest driver, maybe its is the problem, but i need this driver.
Im 100% its the drivers because i've seen many other issues like this with other Audio companies that fixed it with a driver update, exept Creative "wow thats some news" i've allready talked at Technet on Vista 64 forums and person told me that it a driver issue.
Another proof is that if i run windows doing nothing Audiodg.exe uses constantly 0-4% of my CPU, if i start a mp3 its jumps to 6-8% if i turn of Cmss3d in Creative Console it drops instantly to 0% and stays there all the time, so its something with the drivers. running open al software only limits the audiodg to some point, but when running (Teamspeak) with Direct Sound, and (Counter StrikeSource) with Open Al /Alchemy) the Audiodg flips and starting to use 50% sometimes, and it hapends sometimes when i dont use teamspeak, so its Driver problem.
I phoned Creative and they told me on the support that they have no idea and telling the same story = Reainstall drivers etc..

X-fi Elite pro DIN out and Creative speak

hello,
I have the elite pro and megaworks 550 speakers, I have tried to connect the DIN cable from the I/o console to my sub instead of the original speakers remote control. but it is not work..it's won't turn my speakers on.
Is someone succeed to do that? maybe with another speakers? someone know how to fix it's
Thank you very much.

Some 8 months later people like me are still falling into this same trap.
The External console is NOT compatible with the Megaworks & Gigaworks speakers (even the 7. versions) or so I am told by Customer Support after 6 weeks of working through the issues.
Why Creative would design this incompatability into there premier products is beyound me

X-Fi Elite Pro and Radeon 5870

Hello, I've just added Radeon 5870 to my system. I observed some strange behaviour of my X-Fi Elite Pro since then.
Sometimes, when the sound goes really deep it sounds distorted. It never happened before neither with Radeon 3870 nor 4870.
Did you encounter this problem too? I'm thinking about ATI drivers, since they are in the eraly stage.
Every help is appreciated.

The software is named as MediaSource Audio Converter. It comes w/ the MediaSource package which can be found at support/downloads too.
BTW, XtremeAudio is not based on same hardware that those othed X-Fi (PCI) models are so, if you have Li've! 24-bit/Audigy SE/Value or any Audigy 2/4 card there already then you perhaps don't get any other advantage but those couple of bundled additional software only (as like the Chrystalizer).
You can rip CDs and record audio directly to mp3 format by simply using MediaSource Player ... I don't know if there are support for edit VOB or DAT format files (least creative wavestudio 5.0 didn't support) but, supposeingly, there are 3rd party software for this task available.
jutapa

[Help] Creative X-Fi Elite Pro Volume Rem

I have?X-Fi Elite Pro soundcard and Megawork 550 5. speaker. As You know that Elite Pro have an I/O console which have a 9 Pin DIN for remote control. Therefore, I connect my I/O Console with my speaker using the 9 PINS DIN Cable provided by Creative. the problem is, i can't adjust the volume of my speaker at all, it always goes to the max volume no matter how i try to adjust it.

Hi,
I have excactly same problem, tried reinstalling/updating GPU drivers, updating chipset drivers, emptying PCI-slots, putting sound card into different PCI-slots.
Also, it does not seem to have any memory, I/O or DMA conflicts with sound card. Maybe IRQ priorities?
This is what Microsoft says about "Code 2"
http://support.microsoft.com/?scid=kb%3Ben-us%3B3023&x=6&y=3
Specs:
GeForce 6600 GT (AGP)
Kingston Valueram 2x52 Mb Dual channel PC-3200
Abit IC7-MAX3, newest BIOS
SB X-Fi XtremeMusic (with most recent drivers)
Changing AGP Aperture Size to 256 Mb seems to fix the problem, thank you.Message Edited by Vilson on 07-20-2006 0:45 PM

X-Fi Elite Pro no wave support in XP Media Cente

Similar Messages

Maybe you are looking for