Agent 2.2.0 failed: errcode=00000, errmsg=Unexpected error on manager2.2

Hi,
I have a Oracle VM manager having 2 nics and conected to 2 differebt subnets.
I have insatlled 2.2.1 Oracle VM server on HP bl-460.
When i ty to add this server to the manager it says - error on the status bar and in the logs this is what it says.
During creating server pool (172.16.9.20), cluster setup failed: (OVM-1011 OVM Manager communication with 172.16.9.20 for operation HA Setup for Oracle VM Agent 2.2.0 failed: errcode=00000, errmsg=Unexpected error: <Exception: ha_check_hostname_ip failed:<Exception: check srv('172.16.9.20') hostname/IP failed! => <Exception: Invalid hostname/IP configuration: hostname=dmzserver1;ip=127.0.0.1> )
Can anybody please help ASAP

Re: Error status on newly created pool
Error in Creating Server Pool

Similar Messages

PowerOn Failed : Result - failed:errcode=20000, errmsg=No enough memory

Hi,
When I tried to start a VM from ovm manager I get this message 'PowerOn Failed : Result - failed:errcode=20000, errmsg=No enough memory to run vm'
As per this document (https://communities.oracle.com/portal/server.pt/community/view_document/217?docID=198299) I have tried these commands to increase memory
[root@ovm-rac-exp01 ~]# xm info | grep -E '^free_memory'
free_memory : 15590
[root@ovm-rac-exp01 ~]# /opt/ovs-agent-2.3/db/db_kv.py srv ovm-rac-exp01 -t int -f mem_free 15590
old: ovm-rac-exp01 => 0
new: ovm-rac-exp01 => 15590
but after a few seconds mem_free returns to 0
How can I set the mem_free parameter ?
Thanks

I am experiencing the same behavior.
* The OVM server (2.2.2) in my test lab has 8GB physical memory with 563MB assigned to Dom0 per GRUB config: kernel /xen-64bit.gz dom0_mem=563M
* When attempting to start a single Windows 2008 (HVM) VM, allocated 1024MB, and with no other guest VM on the system I see the following in /var/log/ovs-agent/ovs_root.log:
"2011-10-18 12:35:28" DEBUG=> select_tgt_host: vm('/OVS/running_pool/W2K8_SVR01')=>memory=1024
"2011-10-18 12:35:28" ERROR=> select_tgt_host: faild. => errcode=20000, errmsg=No enough memory to run vm(/OVS/running_pool/W2K8_SVR01), required memory=1024.
StackTrace:
File "/opt/ovs-agent-2.3/OVSServerSelection.py", line 336, in select_tgt_host
raise OVSException(ERR_NO_MEMORY, {"vm_path": vm_path, "memory": memory})
"2011-10-18 12:35:28" ERROR=> start_vm: failed! vm('/OVS/running_pool/W2K8_SVR01') errcode=20000, errmsg=No enough memory to run vm(/OVS/running_pool/W2K8_SVR01), required memory=1024.
StackTrace:
File "/opt/ovs-agent-2.3/OVSSiteVM.py", line 124, in start_vm
raise e
"2011-10-18 12:35:28" INFO=> OVSPolicyServer.execute_policy(): vm('/OVS/running_pool/W2K8_SVR01'), action=start_vm action_params=(vm_path, ) => failed:errcode=20000, errmsg=No enough memory to run vm(/OVS/running_pool/W2K8_SVR01), required memory=1024.
StackTrace:
File "/opt/ovs-agent-2.3/OVSSiteVM.py", line 124, in start_vm
raise e
* There seems to be plenty of memory available:
# xm info | grep memory
total_memory : 8156
free_memory : 7490
node_to_memory : node0:7490
* Starting the VM manually using 'xm create' works:
# xm create /var/ovs/mount/C974E8A5DEFF4FD18CBD8D74BE9092D3/running_pool/W2K8_SVR01/vm.cfg
Using config file "/var/ovs/mount/C974E8A5DEFF4FD18CBD8D74BE9092D3/running_pool/W2K8_SVR01/vm.cfg".
Started domain W2K8_SVR01 (id=2)
* Memory usage seems as expected:
# xm list
Name ID Mem VCPUs State Time(s)
Domain-0 0 563 4 r..... 392.1
W2K8_SVR01 2 1024 1 ...... 1.2
# xm info | grep memory
total_memory : 8156
free_memory : 6453
node_to_memory : node0:6453
* Trying the procedure suggested here ( https://communities.oracle.com/portal/server.pt/community/view_document/217?docID=198299 ) is of no use as 'mem_free' reverts to value of zero within a few seconds. It seems the agent is re-reading what it thinks is total available memory (from where?) and updating the database. I tried stopping the agent, changing 'mem_free' value and then restarting the agent but it makes no difference. Not sure procedure in docID=198299 is supported anyway.
* Sorry I can't help much but at least you are not alone in experiencing this issue...

Picture services failed to load - An unexpected error occurred

Just uninstalled Desktop 5.0 and installed Desktop 6.0.
Everything else seems to be working fine. It's just that when I try to access "Media Sync-->Pictures". I get the following message:
"Picture services failed to load - An unexpected error occurred"
I especially need to access my pics b/c my media card is out of room.(perhaps itself a clue?)
I have a Curve 8350i from Nextel/Sprint
I would happily post the "log" entry, but I don't know how to find it and/or turn logging on.
Please help.
Gerard Marra

This is a portion of the Desktop Log. It is strange because the Blackberry Desktop Software 6.0 works fine on my laptop but not on my desktop computer....
14:48:30.075|INFO |9|Rim.Desktop.Media|0|TASK: [Load_Picture_Library], STATE: Failed, TRANSITION: none, OPERATION: none, DURATION: 5304
14:48:30.079|ERROR|9|Rim.Desktop.Media|18005|EXCEPTION: Rim.Desktop.Services.Tasks.Exceptions.TaskFailedException -- MESSAGE: Load_Picture_Library -- STACK: at Rim.Desktop.Services.Tasks.Task.get_Result(){CRLF} at Rim.Media.Source.Pictures.PictureDataSource.GetLibraryResultFromTask(Task task){CRLF} at Rim.Media.Source.Pictures.PictureDataSource.LoadLibraryUsingTask(){CRLF} at Rim.Media.Source.Pictures.PictureDataSource.LoadOriginalDataSource(){CRLF} at Rim.Media.Source.DataSource.LoadDataSource(IDataSourceSnapshot snapshot){CRLF} at Rim.Media.Sync.BBMusicSyncAPI.<>c__DisplayClass12.<GetLoadDataSourceTask>b__e(){CRLF} at Rim.Desktop.Services.Tasks.Task.RunOneOperation()
14:48:30.079|ERROR|9|Rim.Desktop.Media|18005|INNER EXCEPTION: System.IO.IOException -- MESSAGE: The device is not ready.{CRLF} -- STACK: at System.IO.__Error.WinIOError(Int32 errorCode, String maybeFullPath){CRLF} at System.IO.__Error.WinIODriveError(String driveName, Int32 errorCode){CRLF} at System.IO.DriveInfo.get_VolumeLabel(){CRLF} at Rim.Media.Source.Pictures.PictureList.GetFriendlyName(IFolderPath path){CRLF} at Rim.Media.Source.Pictures.PictureList..ctor(IPictureLibrary owner, ILibraryFolder folderPath){CRLF} at Rim.Media.Source.Pictures.PictureLibrary.GetLibrary(IFolderLibrarySession folderLibrarySessionData, ICancelable task){CRLF} at Rim.Media.Source.Pictures.PictureDataSourceLoader.LoadLibrary(ICancelable task){CRLF} at Rim.Media.Source.Pictures.PictureDataSource.<>c__DisplayClass1.<LoadLibraryUsingTask>b__0(){CRLF} at Rim.Desktop.Services.Tasks.Task.RunOneOperation()
14:48:30.079|ERROR|9|Rim.Desktop.Media|18005|EXCEPTION: Rim.Desktop.Services.Tasks.Exceptions.TaskFailedException -- MESSAGE: Load_Picture_Library -- STACK: at Rim.Desktop.Services.Tasks.Task.get_Result(){CRLF} at Rim.Media.Source.Pictures.PictureDataSource.GetLibraryResultFromTask(Task task){CRLF} at Rim.Media.Source.Pictures.PictureDataSource.LoadLibraryUsingTask(){CRLF} at Rim.Media.Source.Pictures.PictureDataSource.LoadOriginalDataSource(){CRLF} at Rim.Media.Source.DataSource.LoadDataSource(IDataSourceSnapshot snapshot){CRLF} at Rim.Media.Sync.BBMusicSyncAPI.<>c__DisplayClass12.<GetLoadDataSourceTask>b__e(){CRLF} at Rim.Desktop.Services.Tasks.Task.RunOneOperation()
14:48:30.080|ERROR|9|Rim.Desktop.Media|18005|INNER EXCEPTION: System.IO.IOException -- MESSAGE: The device is not ready.{CRLF} -- STACK: at System.IO.__Error.WinIOError(Int32 errorCode, String maybeFullPath){CRLF} at System.IO.__Error.WinIODriveError(String driveName, Int32 errorCode){CRLF} at System.IO.DriveInfo.get_VolumeLabel(){CRLF} at Rim.Media.Source.Pictures.PictureList.GetFriendlyName(IFolderPath path){CRLF} at Rim.Media.Source.Pictures.PictureList..ctor(IPictureLibrary owner, ILibraryFolder folderPath){CRLF} at Rim.Media.Source.Pictures.PictureLibrary.GetLibrary(IFolderLibrarySession folderLibrarySessionData, ICancelable task){CRLF} at Rim.Media.Source.Pictures.PictureDataSourceLoader.LoadLibrary(ICancelable task){CRLF} at Rim.Media.Source.Pictures.PictureDataSource.<>c__DisplayClass1.<LoadLibraryUsingTask>b__0(){CRLF} at Rim.Desktop.Services.Tasks.Task.RunOneOperation()
14:48:30.080|INFO |9|Rim.Desktop.Media|0|TASK: [API_LOAD_DATASOURCE_PicturesDesktop], STATE: Progressing, TRANSITION: Progressing -> Finishing, OPERATION: Void <GetLoadDataSourceTask>b__e(), ERROR: Rim.Desktop.Services.Tasks.Exceptions.TaskFailedException: Load_Picture_Library ---> System.IO.IOException: The device is not ready.
 at System.IO.__Error.WinIOError(Int32 errorCode, String maybeFullPath)
 at System.IO.__Error.WinIODriveError(String driveName, Int32 errorCode)
 at System.IO.DriveInfo.get_VolumeLabel()
 at Rim.Media.Source.Pictures.PictureList.GetFriendlyName(IFolderPath path)
 at Rim.Media.Source.Pictures.PictureList..ctor(IPictureLibrary owner, ILibraryFolder folderPath)
 at Rim.Media.Source.Pictures.PictureLibrary.GetLibrary(IFolderLibrarySession folderLibrarySessionData, ICancelable task)
 at Rim.Media.Source.Pictures.PictureDataSourceLoader.LoadLibrary(ICancelable task)
 at Rim.Media.Source.Pictures.PictureDataSource.<>c__DisplayClass1.<LoadLibraryUsingTask>b__0()
 at Rim.Desktop.Services.Tasks.Task.RunOneOperation()
 --- End of inner exception stack trace ---
 at Rim.Media.Sync.BBMusicSyncAPI.DataSourceFailedToLoad(Exception exception)
 at Rim.Desktop.Services.Tasks.Task.RunOneOperation()
 at Rim.Desktop.Services.Tasks.Task.Run()
 at Rim.Media.Sync.BBMusicSyncAPI.LoadDataSource(MediaSource mediaSource, ICancelable parentTask)
 at Rim.Media.Sync.SyncService.<>c__DisplayClasse.<StartUp>b__a()
 at Rim.Desktop.Services.Tasks.Task.RunOneOperation()

Music services failed to load an unexpected error occurred

Hi!
Till the last Day, the WiFi and/ore the USB-Sync with iTunes runs perfectly.
But at this moment, it doens't work anymore and i got this message on my DM6 "Music services failed to load an unexpected error occurred"
I don't know why, cause i didn't change anything on my DM6, iTunes ore Torch.
This ist my Desktop.log
13:05:54.907|INFO |12|Rim.Desktop.Media|39001|Got Request POST http://192.168.2.105:4481/mediasync/music/17afe97cfe9d52d6
13:05:54.910|INFO |12|Rim.Desktop.Media|39001|gzip requested
13:05:54.992|FATAL|12|Rim.Desktop.Shell|0|Fatal Application Error
System.FormatException: The input yields a number greater than 4 bytes.
   bei Rim.Common.Utilities.JavaBinaryReader.ReadCompressedInt()
   bei Rim.Media.Sync.SyncProviders.Device.Destination.DeviceChanges.ReadChanges(Stream changeStream)
   bei Rim.Media.Sync.Listener.HttpMediaServer.OnUpdatesProvided(Object sender, UpdatesProvidedEventArgs e)
   bei Rim.Common.Utilities.Events.Eventer.Raise[THandlerArgs,TArgs](Object sender, EventHandler`1 handler, TArgs e)
   bei Rim.Media.Sync.Listener.MediaHttpListener.Request(IAsyncResult result)
   bei System.Net.LazyAsyncResult.Complete(IntPtr userToken)
   bei System.Net.LazyAsyncResult.ProtectedInvokeCallback(Object result, IntPtr userToken)
   bei System.Net.ListenerAsyncResult.WaitCallback(UInt32 errorCode, UInt32 numBytes, NativeOverlapped* nativeOverlapped)
   bei System.Threading._IOCompletionCallback.PerformIOCompletionCallback(UInt32 errorCode, UInt32 numBytes, NativeOverlapped* pOVERLAP)
13:05:54.994|FATAL|12|Exception|0|Fatal Error
System.FormatException: The input yields a number greater than 4 bytes.
   bei Rim.Common.Utilities.JavaBinaryReader.ReadCompressedInt()
   bei Rim.Media.Sync.SyncProviders.Device.Destination.DeviceChanges.ReadChanges(Stream changeStream)
   bei Rim.Media.Sync.Listener.HttpMediaServer.OnUpdatesProvided(Object sender, UpdatesProvidedEventArgs e)
   bei Rim.Common.Utilities.Events.Eventer.Raise[THandlerArgs,TArgs](Object sender, EventHandler`1 handler, TArgs e)
   bei Rim.Media.Sync.Listener.MediaHttpListener.Request(IAsyncResult result)
   bei System.Net.LazyAsyncResult.Complete(IntPtr userToken)
   bei System.Net.LazyAsyncResult.ProtectedInvokeCallback(Object result, IntPtr userToken)
   bei System.Net.ListenerAsyncResult.WaitCallback(UInt32 errorCode, UInt32 numBytes, NativeOverlapped* nativeOverlapped)
   bei System.Threading._IOCompletionCallback.PerformIOCompletionCallback(UInt32 errorCode, UInt32 numBytes, NativeOverlapped* pOVERLAP)
13:05:58.439|INFO |12|Rim.Desktop.Media|39001|HttpMediaServer status update: ServerOn
What can i do, to fix the problem?
Tank you!
Sorry for my bad english
Greetings from Germany
Kalorie99

I found the answer, here in the forum from a user:
Here is the solution that worked for me, based on antoniovtorres post (I resisted the urge to get PO'd and tried to figure out what he must have done):
With desktop manager closed, using Blackberry user tools, navigate to 'Blackberry\system\' (make sure that hidden files are shown or you won't see the 'system' folder).
Move or delete the folders 'Media Sync' and 'media' from the system directory.
Re-open desktop manager.
Click yes to any dialog that appears.
You should now be able to sync music again.
Note that your device may want to double up on your synced pictures and videos, so you may want to delete your pictures and videos off of the device before your next picture or video sync. Hope it works for y'all.
Scott
It works again!
Yeah!
BlackBerry rocks!

I am trying to set up iCloud to sync my Outlook Calendar however it keeps failing due to 'an unexpected error' but it doesn't say what the error is! Any suggestions would be gratefully received.

I am trying to set up iCloud to sync my Outlook Calendar however it keeps failing due to 'an unexpected error' but it doesn't say what the error is! Any suggestions would be gratefully received.

Create a iTune and App Store account without credit card
1. Go to App Store and select a free app
2. Tap INSTALL APP
3. Create New Apple ID
4. Confirm Your Country
5. Agree with Terms and Conditions
6. Fill in your Apple ID and Password (must be a valid email address)
7. Create and answer your secret question e.g. What is the name of my dog?
8. Select NONE for Payment Method
9. Fill in Billing Address i.e. your address
10. Submit application for new Apple ID
11. Wait for verification email
12. When email arrive, verify your account
13. Start downloading your free apps

Yaourt fails "error: failed to prepare transaction (unexpected error)"

Today, I am trying to do a full system upgrade using yaourt, but I get this strange message:
[christian@pb-tj72 ~]$ yaourt -Syua
:: Synchronizing package databases...
core is up to date
extra is up to date
community is up to date
error: failed to prepare transaction (unexpected error)
:: Starting full system upgrade...
It makes me wonder that it first reports the error and then executes the full system upgrade.
I hope that this is a well-known problem or that somebody can help me with instructions regarding how to increase verbosity or which log files to look at.
Otherwise, will the yaourt-alternatives work with the AUR packages that I've already installed with yaourt?
BR,
Christian

SS4 wrote:I'd imagine yaourt has a -v switch for verbose
I tried yaourt -Syuv (didn't work together with the '-a' switch). First I got error: you cannot perform this operation unless you are root., but when running as sudo, it works. This makes me wonder whether the -v switch is undocumented or if it invokes pacman instead.
pstree -a shows me that in fact, yaourt -Syuv launches pacman -Syuv
nbvcxz wrote:Please find if you have some packages installed with "unsatisfied" dependences (eg. pulseaudio but no rtkit or libreoffice but no orbit2). To see more please do first pacman -Syu - should tell you more.
pacman -Syu tells me that I do have unresolved dependencies since my kernel is frozen until a certain bug is resolved:
warning: linux: ignoring package upgrade (3.2.14-1 => 3.3.2-1)
resolving dependencies...
warning: ignoring package linux-3.3.2-1
warning: cannot resolve "linux>=3.3", a dependency of "virtualbox-modules"
warning: ignoring package linux-3.3.2-1
warning: cannot resolve "linux>=3.3", a dependency of "virtualbox-modules"
But shouldn't yaourt handle this in the same way that pacman would?
My conclusion so far is that yaourt doesn't work with unresolved dependencies. So I will try another tool.

When importing files from desktop to laptop using home sharing, files fail to copy "An unexpected error occured (-50)"

So I'm trying to copy my library from my desktop computer to my laptop. I'm using the import feature when browsing the other library through Home Sharing. Some files wil copy, anywhere from 6-150 songs then it will fail. I have 6000 songs to copy, so I really don't want to babysit my way through this. I'm having to use my wireless network (no external drive available), but it is pretty sturdy. It hasn't been giving me any grief to stream the music, just to copy Is there any fix for this?

The following comes from the LaCie web site but is applicable to any other external drives whether home brew or commercial.
Getting error -50 when copying data in OS X.
Some drives ship out formatted FAT32 so they will be ready to use on either a Mac or a PC. If you are getting error -50 when copying to a drive formatted for PC, it is because of the following:
Certain characters that can be used in a Mac OS X filename are not allowed in MS-DOS filenames. This can prevent the file from being copied, and can occur when a filename contains non-printing ASCII characters, or any of these characters: ? / \ < > " | > *.
Either copy the data off of the drive and use Apple's Disk Utility to erase the drive in Mac OS Extended format, or change the filenames of the documents that cannot be copied.

Securing agent... Failed. !!!!

[oracle@srvldbt02 config]$
Enter Agent Registration Password : Securing agent... Failed.
How can i change the Password?
Rgds

Not sure what you trying to do here.
The password you should use when securing your agent, should be the password you entered during installation.
The installer has asked you to enter a password to secure the Management Server.
The password you entered here, should be used when securing agents that must upload to this OMS
Regards
Rob

DPM failed to communicate with the protection agent on DPM 2010 SERVER because the agent is not responding. (ID 43 Details: Internal error code: 0x8099090E)

Hi everyone,
Backup jobs for protected members are intermittently failing with the following error on the DPM server:
DPM failed to communicate with the protection agent on <DPM 2010 SERVER> because the agent is not responding. (ID 43 Details: Internal error code: 0x8099090E)
Why does the DPM server failing to see it's own DPM agent cause the backup job for another server to fail? One day a backup will work fine, the next it may fail; and the next back to normal again...
The following error is recorded in the Service Control Manager event log on the DPM server just prior to the above error:
A timeout was reached (30000 milliseconds) while waiting for the DPMRA service to connect.
Thank you.
With regards,
Rob

Hello,
I have read these entire postings and see that my problems match most of the above problems.
I believe we have tried all of the ideas in this blog and lots of other ideas from other forums and internet searches.
We have about 80 small databases protected and set at 15 minute incremental and most will work but some fail. When they fail the most common, but not only error, is something like "DPM
failed to communicate with the protection agent on <DPM 2010 SERVER> because the agent is not responding. (ID 43 Details: Internal error code: 0x8099090E)". The alert is inactivated in the DPM Console, and the backups resume as normal."
Since later jobs are successful I thought all was well. All was well until I went to restore from incremental backups. We worked for two days (day and night work) to restore
from a corrupted virtual disk on our SQL Server 2008 R2. I suspect DPM had something to do with the corrupted virtual disk. All I know is that we never had this problem until installing DPM. Here is what we encountered when we went to restore
from the protection points:
* Restore jobs take a minimum of 15 minutes for jobs that are 45 MB or 2 GB.
* If you pick a backup from the list of recovery points that is not valid the job runs for 15 minutes and then "Failed".
* You cannot rerun the job because SQL Server 2008 has the table being recovered as <tablename> (recovering) and a retry will not work. Of course time is wasted while waiting
to see if it worked.
* Eventually you realize that even after dropping the table in the (recovering) mode in SQL that the restore point must be bad or possibly one of this failed recovery points.
* So begins the quest to start restoring recovery points one by one and 15 minutes by 15 minutes until you find one that actually restores to a SQL Instance.
* If you have 80 of these to do and you average trying three recovery points and each takes 15 minutes, not to mention the time to drop the table in SQL, well that time adds up to 3,600
minutes of trial and error. 60 hours of trial and error, wow not much of a savings using DPM over a SQL backup plan.
* And then you have to explain to your customers that their databases were restored but you do not know at what point the DB was restored.
All in all it seems like DPM concept is great but like many backups the backup plan looks good on paper but actually restoring a backup is quite a different matter.
I don't know if anyone has ever solved the problems presented in this forum but if they have then I wish they would post and if no one has solved the problem then shame on DPM.
Good luck everyone, but I for one have spent about two months on trying to protect and restore consistently. I have never had one day of consistent and reliable restore points. I
am going back to sql management plans for my backups. I have never, in 10 years had a sql generated backup fail me. Never.
gbl

Failed to open service OracleDEV102TNSListener , error 1060

Dear Consultants,
I have been trying to install ECC6 , Oracle on Windows 2003, and my Hardware is RAM --2 GB
HDD -- 300GB
I am having intel duo core processor and iam using Gigabyte motherboard,Intel chipset.
My Installations stops at Import_Abap phase, following are the logs ,
ERROR 2007-03-10 04:47:46
CJS-30022 Program 'Migration Monitor' exits with error code 103. For details see log file(s) import_monitor.java.log, import_monitor.log.
ERROR 2007-03-10 04:47:47
FCO-00011 The step runMigrationMonitor with step key |NW_Onehost|ind|ind|ind|ind|0|0|NW_Onehost_System|ind|ind|ind|ind|1|0|NW_CreateDBandLoad|ind|ind|ind|ind|9|0|NW_ABAP_Import_Dialog|ind|ind|ind|ind|5|0|NW_ABAP_Import|ind|ind|ind|ind|0|0|runMigrationMonitor was executed with status ERROR .
INFO 2007-03-10 05:03:18
An error occured and the user decide to stop.\n Current step "|NW_Onehost|ind|ind|ind|ind|0|0|NW_Onehost_System|ind|ind|ind|ind|1|0|NW_CreateDBandLoad|ind|ind|ind|ind|9|0|NW_ABAP_Import_Dialog|ind|ind|ind|ind|5|0|NW_ABAP_Import|ind|ind|ind|ind|0|0|runMigrationMonitor".
I have set the all the Environment variables , i run r3trans -d and the result is
C:\Documents and Settings\devadm>r3trans -d
This is r3trans version 6.13 (release 700 - 20.02.06 - 16:15:00).
unicode enabled version
2EETW169 no connect possible: "connect failed with DBLI_RC_LOAD_LIB_FAILED."
r3trans finished (0012).
I also run r3trans -x and the result is.
4 ETW000 [dbsloci. ,00000] *** ERROR => CONNECT failed with sql error '12541'
4 ETW000 21 1.098448
4 ETW000 [dev trc ,00000] Try to connect with default password 142 1.098590
4 ETW000 [dev trc ,00000] Connecting as SAPSR3/<pwd>@DEV on connection 0 (nls_hdl 0) ... (dbsl 700 240106)
4 ETW000 22 1.098612
4 ETW000 [dev trc ,00000] Nls CharacterSet NationalCharSet C EnvHp ErrHp ErrHpBatch
4 ETW000 23 1.098635
4 ETW000 [dev trc ,00000] 0 UTF8 1 0244CF08 0245243C 02451CC4
4 ETW000 24 1.098659
4 ETW000 [dev trc ,00000] server_detach(con_hdl=0,stale=0,svrhp=02463484) 14 1.098673
4 ETW000 [dev trc ,00000] Detaching from DB Server (con_hdl=0,svchp=02451C10,srvhp=02463484)
4 ETW000 19 1.098692
4 ETW000 [dev trc ,00000] Deallocating server context handle 02463484 16 1.098708
4 ETW000 [dev trc ,00000] Allocating server context handle 15 1.098723
4 ETW000 [dev trc ,00000] Attaching to DB Server DEV (con_hdl=0,svchp=02451C10,svrhp=02463484)
4 ETW000 29 1.098752
4 ETW000 [dev trc ,00000] Tue Mar 13 04:38:09 2007 1093335 2.192087
4 ETW000 [dboci.c ,00000] *** ERROR => OCI-call 'OCIServerAttach' failed: rc = 12541
4 ETW000 19 2.192106
4 ETW000 [dbsloci. ,00000] *** ERROR => CONNECT failed with sql error '12541'
4 ETW000 19 2.192125
4 ETW000 [dblink ,00431] ***LOG BY2=>sql error 12541 performing CON [dblink#3 @ 431]
4 ETW000 176 2.192301
4 ETW000 [dblink ,00431] ***LOG BY0=>ORA-12541: TNS:no listener [dblink#3 @ 431]
4 ETW000 19 2.192320
2EETW169 no connect possible: "DBMS = ORACLE --- dbs_ora_tnsname = 'DEV'"
Event Viewer result is
----
Faulting application isqlplussvc.exe, version 1.0.7.0, faulting module msvcrt.dll, version 7.0.3790.0, fault address 0x0003113b.
finally in SAPINST logs i could see

Starting tnslsnr: please wait...
Failed to open service <OracleDEV102TNSListener>, error 1060.
TNSLSNR for 32-bit Windows: Version 10.2.0.1.0 - Production
System parameter file is C:\oracle\DEV\102\network\admin\listener.ora
Log messages written to C:\oracle\DEV\102\network\log\listener.log
Listening on: (DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(PIPENAME=
.\pipe\DEV.WORLDipc)))
Listening on: (DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(PIPENAME=
.\pipe\DEVipc)))
Listening on: (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=DEV)(PORT=1527)))
Connecting to (ADDRESS=(PROTOCOL=IPC)(KEY=DEV.WORLD))
STATUS of the LISTENER
Alias LISTENER
Version TNSLSNR for 32-bit Windows: Version 10.2.0.1.0 - Production
Start Date 10-MAR-2007 01:29:29
Uptime 0 days 0 hr. 0 min. 3 sec
Trace Level off
Security ON: Local OS Authentication
SNMP OFF
Listener Parameter File C:\oracle\DEV\102\network\admin\listener.ora
Listener Log File C:\oracle\DEV\102\network\log\listener.log
Listening Endpoints Summary...
(DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(PIPENAME=
.\pipe\DEV.WORLDipc)))
(DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(PIPENAME=
.\pipe\DEVipc)))
(DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=DEV)(PORT=1527)))
Services Summary...
Service "DEV" has 1 instance(s).
Instance "DEV", status UNKNOWN, has 1 handler(s) for this service...
The command completed successfully
Please suggest for the possible workaround, as you can see i have tried everything.
Regards,

Dear Umesh,
I have triggered the Installation again, still the problem remains unresolved,
PLEASE CONFIRM THAT I AM USING INTEL CORE DUO PROCESSOR , does it have any dependcies or prerequisites.
pasting the last few lines of logs of SAPAPPL1_15, where i got the error in ABAP IMPORT.
DbSl Trace: ORA-4031 occurred when executing SQL statement (parse error offset=0)
(DB) ERROR: DDL statement failed
(CREATE UNIQUE INDEX "VDBEPI_EU~0" ON "VDBEPI_EU" ( "MANDT", "BUKRS", "RBELKPFD", "RPOSNR" ) TABLESPACE PSAPSR3 STORAGE (INITIAL 16384 NEXT 0000002560K MINEXTENTS 0000000001 MAXEXTENTS 2147483645 PCTINCREASE 0 ) )
DbSlExecute: rc = 99
(SQL error 4031)
error message returned by DbSl:
ORA-04031: unable to allocate 40 bytes of shared memory ("shared pool","CREATE UNIQUE INDEX "VDBEPI_...","Typecheck","qcsqlpath: qcsAddSqlPath")
(DB) INFO: disconnected from DB
E:\usr\sap\NAJ\SYS\exe\uc\NTI386\R3load.exe: job finished with 1 error(s)
E:\usr\sap\NAJ\SYS\exe\uc\NTI386\R3load.exe: END OF LOG: 20070517090126
===================================================
IMPORT_MONITOR.JAVA logs.
Import Monitor jobs: running 2, waiting 35, completed 34, failed 1, total 72.
Loading of 'SAPAPPL1_15' import package: ERROR
Import Monitor jobs: running 1, waiting 35, completed 34, failed 2, total 72.
Loading of 'SAPAPPL2_5' import package: ERROR
Import Monitor jobs: running 0, waiting 35, completed 34, failed 3, total 72.
Import Monitor jobs: running 1, waiting 34, completed 34, failed 3, total 72.
Import Monitor jobs: running 2, waiting 33, completed 34, failed 3, total 72.
Import Monitor jobs: running 3, waiting 32, completed 34, failed 3, total 72.
Loading of 'D021T' import package: OK
Import Monitor jobs: running 2, waiting 32, completed 35, failed 3, total 72.
Import Monitor jobs: running 3, waiting 31, completed 35, failed 3, total 72.
Loading of 'SAPAPPL1_12' import package: OK
Import Monitor jobs: running 2, waiting 31, completed 36, failed 3, total 72.
Import Monitor jobs: running 3, waiting 30, completed 36, failed 3, total 72.
Loading of 'SAPSSEXC_4' import package: OK
Import Monitor jobs: running 2, waiting 30, completed 37, failed 3, total 72.
Import Monitor jobs: running 3, waiting 29, completed 37, failed 3, total 72.
Loading of 'SAPSSEXC_6' import package: OK
Import Monitor jobs: running 2, waiting 29, completed 38, failed 3, total 72.
Regards,

Cannot start VM - IDE Emulator Failed to Power on with Error 'The service cannot be started, either because it is disabled or because it has no enabled devices associated with it.'

HI all.
New install of 2008R2 on HP DL-380 G6. I have created (several) VM's none of which will start. If I remove the IDE Hard Disk and add a DVD of the OS ISO, it will boot and start the install (although with no HDD).
It seems like the IDE controller is working ok - it is what the DVD drive is using, but it cannot mount a VHD. The error indicates a driver is not working (although the DVD on IDE works fine) so something to do with VHD? I can attach the VHD
in disk management, so it does not seem corrupt - again I have tried with both dynamic and fixed VHDs.
Full error is:
'Test1' failed to start. (Virtual machine ID 4320D2D6-DF7E-40D2-BD0F-9562CBB9F052)
'Test1' Microsoft Emulated IDE Controller (Instance ID {83F8638B-8DCA-4152-9EDA-2CA8B33039B4}): Failed to Power on with Error 'The service cannot be started, either because it is disabled or because it has no enabled devices associated with it.' (0x80070422).
(Virtual machine ID 4320D2D6-DF7E-40D2-BD0F-9562CBB9F052)
'Test1': Failed to open attachment 'C:\Users\Public\Documents\Hyper-V\Virtual hard disks\New Virtual Hard Disk.vhd'. Error: 'The service cannot be started, either because it is disabled or because it has no enabled devices associated with it.' (0x80070422).
(Virtual machine ID 4320D2D6-DF7E-40D2-BD0F-9562CBB9F052)
Any Ideas?

Hi ,
Did you try to disable the services , if they are exsit :
HP Smart Array SAS/SATAEvent notification
HP Insight storage agents
Then restart your server .
Best Regards
Elton Ji
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

When trying to update my CC apps, the update fails. I get this error: Update Failed. There was an error installing this update. Please try again later or connect customer support. This is currently happening for InDesign, Photoshop and Bridge. I had this

When trying to update my CC apps, the update fails. I get this error: Update Failed. There was an error installing this update. Please try again later or connect customer support. This is currently happening for InDesign, Photoshop and Bridge. I had this problem previous and was able to fix by doing a complete wipe of my computer and reinstalling CC. However, I should not have to wipe my computer clean everytime I need to do a CC update. HELP!

Hi,
Please download the updates directly from the link below:
WIN: All Adobe CC 2014 Updates: The Direct Download Links for Windows | ProDesignTools
MAC: All Adobe CC 2014 Updates: The Direct Download Links for Mac OS | ProDesignTools
Regards,
Sheena

Atempt to start OMS for Grid Control 11g fails with - Unexpected error occu

Hello,
I am running Grid Control 11g.
Repository DB is 11.2.0.1
Both the Grid Control and DB server are running in same machine - redhat 5.
When trying to start the oms, this fails with the below error:
Oracle Enterprise Manager 11g Release 1 Grid Control
Copyright (c) 1996, 2010 Oracle Corporation. All rights reserved.
Starting WebTier...
WebTier Successfully Started
Starting Oracle Management Server...
Oracle Management Server is not functioning because of the following reason:
Unexpected error occurred. Check error and log files.
The emctl.log shows the following error which I am unable to debug:
2011-09-13 11:20:05,619 [main] DEBUG oms.StatusOMSCmd processStatusOMS.138 - HTTP port in emgc property file: 7202
2011-09-13 11:20:05,620 [main] DEBUG oms.StatusOMSCmd processStatusOMS.139 - HTTPS port in emgc property file: 7301
2011-09-13 11:20:05,620 [main] DEBUG oms.StatusOMSCmd processStatusOMS.155 - Using http port.
2011-09-13 11:20:05,620 [main] DEBUG oms.StatusOMSCmd processStatusOMS.195 - Attempting to connect to http://<host>.<domain>:7202/em/console/logon/logon
2011-09-13 11:23:05,596 [main] ERROR oms.StatusOMSCmd processStatusOMS.239 - Read timed out
java.net.SocketTimeoutException: Read timed out
at java.net.SocketInputStream.socketRead0(Native Method)
at java.net.SocketInputStream.read(SocketInputStream.java:129)
at HTTPClient.BufferedInputStream.fillBuff(BufferedInputStream.java:206)
at HTTPClient.BufferedInputStream.read(BufferedInputStream.java:126)
at HTTPClient.StreamDemultiplexor.read(StreamDemultiplexor.java:348)
at HTTPClient.RespInputStream.read(RespInputStream.java:147)
at HTTPClient.RespInputStream.read(RespInputStream.java:108)
at HTTPClient.Response.readResponseHeaders(Response.java:1107)
at HTTPClient.Response.getHeaders(Response.java:832)
at HTTPClient.Response.getStatusCode(Response.java:331)
at HTTPClient.RetryModule.responsePhase1Handler(RetryModule.java:92)
at HTTPClient.HTTPResponse.handleResponseImpl(HTTPResponse.java:872)
at HTTPClient.HTTPResponse.access$000(HTTPResponse.java:62)
at HTTPClient.HTTPResponse$2.run(HTTPResponse.java:839)
at HTTPClient.HTTPResponse$2.run(HTTPResponse.java:837)
at HTTPClient.HttpClientConfiguration.doAction(HttpClientConfiguration.java:666)
at HTTPClient.HTTPResponse.handleResponse(HTTPResponse.java:837)
at HTTPClient.HTTPResponse.getStatusCode(HTTPResponse.java:242)
at oracle.sysman.emctl.oms.StatusOMSCmd.processStatusOMS(StatusOMSCmd.java:199)
at oracle.sysman.emctl.wls.OMSController.statusOMS(OMSController.java:867)
at oracle.sysman.emctl.wls.OMSController.startOMS(OMSController.java:606)
at oracle.sysman.emctl.wls.OMSController.main(OMSController.java:213)
2011-09-13 11:23:05,597 [main] INFO wls.OMSController statusOMS.950 - statusOMS finished with result: 9
In emgc.properties, I have MSPORT=7202.
I have used the notes in Metalink 1287904.1, but without resolution.
I am able to connect with sqlplus, with user sysman, without issues. There are no invalid objects under sysman.
emoms.trc shows the following:
2011-09-11 15:51:53,160 [JobWorker 22356:Thread-108] WARN jdbc.ConnectionCache _getConnection.353 - Invalid or Stale Connection found in the Connection Cache
java.sql.SQLException: Invalid or Stale Connection found in the Connection Cache
Thank you for support.
Regards,
Horia
Edited by: horia.berca on Sep 13, 2011 5:29 AM
Edited by: horia.berca on Sep 13, 2011 5:32 AM
Edited by: horia.berca on Sep 13, 2011 5:35 AM
Edited by: horia.berca on Sep 13, 2011 5:45 AM

Hello again;
Check the solution in this: ( and note the multiple versions of oracle it covers )
UNABLE TO FIND GRID INFRASTRUCTURE LISTENER (Doc ID 1483234.1)
Best Regards
mseberg

"New lifecycle definition" fails with "Unexpected error"

This problem has been previously posted without resolution.
Select "Lifecycle Definitions -> New lifecycle definition".
Error:
"Unexpected error, unable to find item name at application or page level.
A severe error has occurred. Possible causes may include moving directly to a page using the browser history or Back key, multiple users attempting to change the same data or an application defect. Please visit the Support page under the Help Tab to report the error.
Press here to return to the parent page"
A resolution to this would be apprciated.
Please note this problem is based on APEX 4. About to retest on APEX 3.2 to see if it is happening there.
Edited by: user774105 on 7/03/2011 17:26
Have back ported to 3.2 and the problem no longer occurs. Not sure what has changed between versions, but there are a number of links in the Assitant that fail with the above error in APEX 4.
Edited by: user774105 on 7/03/2011 19:45

Hi
I have also encounter the same error . Currently i have apex version 4.
User: SYSTEM
Unexpected error, unable to find item name at application or page level.
A severe error has occurred. Possible causes may include moving directly to a page using the browser history or Back key, multiple users attempting to change the same data or an application defect. Please visit the Support page under the Help Tab to report the error.
Press here to return to the parent page
Any solution for this with apex version 4
Thanks and Regards
Ganesan Sivaraman

Excel fails with unexpected error unless vba editor opened before running

i have an excel macro which fails with an unexpected error unless i open vba editor first
EXACT MESSAGE IS
"MICROSOFT EXCEL HAS ENCOUNTERED A PROBLEM AND NEEDS TO CLOSE, WE ARE SORRY FOR THE INCONVENIENCE"
I HAVE SENT AN ERROR REPORT many times, no response
this prevents running as auto_open
why?
what initialization takes place by opening vba editor that does not take place with out doing so?

As this is unusual behavior (not seen by most of us Excel users), and you indicate that it happens on multiple PCs (so it isn't something corrupt on just one machine), it seems likely that it is something specific to the code you are trying to run.
It might be helpful if you post your code, and specifically where you are placing the code (personal.xlsb, a regular module, a class module, behind a specific worksheet, or behind the "this workbook" object).
Also, how are you triggering the macro- are you running it from the macro dialogue box, a custom worksheet button, a userform, or something else?

Agent 2.2.0 failed: errcode=00000, errmsg=Unexpected error on manager2.2

Similar Messages

Maybe you are looking for