Can I boot an iMac from my PB in Target Disk Mode?

I'm housesitting at my parents this weekend, and would like to know if I can bootup my Powerbook G4 in Target Disk mode and then use it as the Startup volume on my parents Intel iMac. In System Preferences it doesn't give my Hard Drive as an option for a startup volume.
I think I just answered my question... OS X on my Powerbook is the PPC version... and probably can't use the PPC version as a Startup on the Intel....

Hi Joel Jenkins;
I would say NO.
First of all since they have an Intel and you have PowerPC The code will not be compatible. Secondly there the problem that the Intel machine has to have the disk formatted differently. So I don't think this idea will work for you.
Why pray tell were you thinking of doing this any way? Exactly what did you hope to accomplish?
Allan

Similar Messages

  • How can i stop my mbp from starting up in target disk mode

    how can i stop my mbp from starting up in target disk mode

    It should only do that if you hold down the T key at startup.  Otherwise the PRAM battery is probably near death, or the T key needs to be cleaned so it doesn't think it is being held down.  To clean the keyboard properly, you will probably need to bring it in for service.

  • Can I access files copied to this machine in target disk mode from this machine?

    Can I access files copied to this machine in target disk mode from this machine?

    HI Claire,
    YOu didn't indicate which Mac OS you are using so I'm going to assume 10.4.x.
    Connect the FireWire cable to the target computer after starting it up in FireWire Target Disk Mode.
    *If the cable was already connected, unplugging it from either computer and plugging it back in should allow the target computer's hard disk to appear on the host.*
    Also, make sure you have the most recent Firmware for your iBook... go here:
    http://support.apple.com/kb/HT1471?viewlocale=en_US
    Carolyn

  • Can u boot from a Mac in target disk mode

    I'm wanting to know if I put a Mac mini in target disk mode, can I boot from that Mac mini from my MacBook Pro. I'm wanting to set up a mini as a server but it may have to be the basic and ill install server on it but I prefer to do it without using a monitor. I'm curious to know if its possible.

    You don't need a monitor with the MM, and neither boot in Target Mode. Like me, use screen sharing for remote access over the network:
    On the MM, -> System Preferences -> Sharing, there check Remote Management and choose which user, if not all, may have access. If you're not the only one, you can limit access for each user under Options.
    Under  -> System Preferences -> Energy Saver, it makes sense to check Wake for network access.
    Then you can log out from the MM, leave it sitting at the login screen and turn off or disconnect its screen.
    On the remote Mac, open Finder and find the MM under Shared. Click in it, then on Share Screen. You'll need to enter the login credentials for your account on the MM, eventually save it to your Keychain. Then your MM's login screen should appear in a window on your remote Mac. You have now full access to the MM.

  • Hard disk not recognised - will not boot from cd & No FW Target Disk mode

    hi,
    some help would be greatly appreciated.
    Some time ago i was switching internal hard drives around and wound up with a kernel panic of some sort (see my previous posts).
    following on from this I have tried FW target disk mode with no success, and it will not boot from a retail Tiger install disc (this machine has tiger installed (i think!). I can't force a boot from the optical drive and i also can't even force it to eject the disc inside to try another install DVD/CD (I have panther discs lying around also).
    when i start up with the c key nothing happens, but when i start up with the alt/option key i get a closed padlock symbol, password entry field and a "right facing arrow" button.
    anyone got any clues with this? i'm guessing it could either and/or be an internal hard drive ribbon failure (i have swapped internal HDs multiple times in this machine, which can't be good for it) or the familiar PRAM problem (although why would it not boot from an install DVD if this was the case?). I have changed the power supply unit in the past due to having a power cable snap off inside the original one - damage to PRAM caused by this?
    help would be muchly appreciated!
    Jesse

    Hi, Jesse. Remove the hard drive and its cable, then see whether you can start up from a CD or DVD. If that works, replace your hard drive cable.

  • IMac G4/800 in FireWire Target Disk Mode shuts down, hard drive hopeless?

    I have found myself in possession of a 12 year-old iMac G4/800. The machine looks stock and was nice and full of dust when I took it apart, so I'm going to assume nothing has been upgraded on it. The person who the computer belongs to has had issues booting the machine and when it does boot, the machine will throw up the "grey screen of death" after a few seconds, I suspect when the hard drive starts to get hit.
    I've attempted to start the machine in FireWire Target Disk Mode and the machine will mount on my 2011 MacBook Pro, however once I begin to copy files the machine will abruptly shut off.
    I have also attempted to remove the hard drive from the machine and connect it to my MacBook Pro via an OWC Drive Adapter, but it won't mount from the adapter in Disk Utility, Terminal or Disk Warrior. I've connected other (non-IDE) drives with the adapter before, but no luck with this one. Perhaps the IDE connector is faulty on the adapter?
    I may look for another drive adapter and I've made an Apple Genius app't for later this afternoon, but I'm curious if anyone has any further advice. Is it more likely that it's a motherboard issue that's causing the machine to shut of in FTDM or a hard drive issue? In any case, this may be one for the Data Rescue Experts. I imagine I may get a few looks at the Apple store with such an old machine.

    Another contributory issue to booting in an older PPC Mac is the PRAM battery.
    If the battery is more than four years old, it would likely be a partial cause of odd
    startup issues and some settings that are required for the computer to start &
    run correctly would not be available. The battery is a 3.6V. 1/2AA Lithium cell.
    http://eshop.macsales.com/item/NewerTech/BAA36VPRAM/
    A few companies such as macsales.com show them on their web site... sounds
    like your old iMac G4 800MHz could use one. Note there are takeapart instruction
    pages online such as one from XLR8Yourmac from years ago. The 800MHz is
    similar to the later models with faster G4 processors of the same appearance.
    The hard drive type utilized is the older ATA/IDE or PATA; uses older formatting.
    Tools, thermal paste, and some other tedious details need to be attended to...
    •iMac G4 Take-apart for Drive and RAM upgrades:
    http://www.xlr8yourmac.com/systems/imac_g4/imacg4_takeapart.html
    And another fairly good page w/ larger images:
    •Mr Totes' iMac G4 -- taken apart:
    http://www.mrtotes.co.uk/page1/page1.html
    Sometimes the power supplies and other components can be the cause of issues
    in these iMac G4 models, you can test the power output by using the test ports
    that are located in the same compartment as the upgrade RAM slot & wi-fi card.
    You may be able to find a copy of an original Apple service manual for that iMac.
    Those are harder to get, and used to be available to Apple trained technicians.
    Good luck & happy computing!

  • Unable to boot PowerBook G4 (15-inch Aluminum) in target disk mode

    I wanted to move some files from my G4 AGP to my faster G4 Powerbook. When I try to start the G4 Powerbook in target mode I get the t on the screen and then see a bar along the bottom center of the screen which contains a little red bar and then it shuts down.
    When I try to restart, the Powerbook is dead and I have to reset the PMU. It will then start up normally.
    There is currently no battery for the Powerbook and I am running with the power adapter only. Could this be the problem?

    The 15" Powerbooks have two batteries. One is the one you can remove from the bottom of the machine without any screws, the other you need detailed instructions of the computer's interior and special parts to replace. The user accessible battery will only impact Target Disk Mode if you have no A/C power to connect to the wall outlet, and it also is out of juice. The non-user accessible battery if it gets more than 4 years old, can impact Target Disk Mode accessibility even if you are plugged into A/C power from the wall outlet. If your power brick is frayed, it may not be giving power to the computer, or if the power manager is damaged it may not give power to the computer. See my FAQ*:
    http://www.macmaps.com/frayguide.html
    Consider how old your machine is, and likelihood of one problem versus the other. If you are in the U.S., these places may be cheaper to replace the non-user accessible battery than Apple or other authorized service technicians:
    http://www.dttservice.com/
    http://www.powerbookresq.com/
    http://www.microdocusa.com/
    http://www.macspecialist.com/
    http://www.techrestore.com/
    If you feel up to the challange, you can order the parts and replace that battery yourself with instructions from http://www.ifixit.com/
    - * Links to my pages may give me compensation.

  • Help please.  Can't boot my iMac from the optical drive.

    17" flat panel, 1GHz iMac, running OS 10.2.8.
    I've been trying to do some disk maintenance and would like to be able to repair my boot disk. I've tried to boot from the optical drive, using Norton SystemWorks CD-ROM and also my iMac software install and repair DVD, holding down the C key while attempting to boot. After trying for a few seconds, a gray veil drops down and a text box telling me that I have to shut down by holding the power key for many seconds shows up. (Is this a Kernel panic?)
    I've also run Repair Permissions. That program seems to stall right at the end, as the status bar is 99% full, and never completes its run.
    Any suggestions?

    Hi MacGeezer,
    DO NOT USE NORTON SYSTEMWORKS
    Norton Utilities and Disk Doctor were discontinued almost 2 years ago (for some very good reasons!). It caused much more trouble than it solved.
    Here are the articles:
    Symantec discontinues Mac Norton Utilities, SystemWorks
    Norton Utilities, SystemWorks development halted
    TMO Scoop - Symantec Confirms Norton Utilities & SystemWorks' Demise [Updated]
    Tech Tool Pro and DiskWarrior are presently the most reliable utilities. For more information on regular housekeeping read this: MacOS X 10.3/10.4: System maintenance

  • Safely copying files from Target Disk Mode to External USB. Advice?

    Just got a new iMac and transferred my system and important files to it from my old iMac. However, a partition on my old iMac has files I want to move to my new iMac so they can be included in Time Machine backups while others I want to move to another external hard drive since I have physical copies of most of those files elsewhere.
    I can connect my old iMac to the new via Target Disk mode and copy the critical files from Mac-to-Mac easily and quickly enough. What I want to know is if I’m safe to copy the other files from the TDM-connected iMac to a USB drive.
    I’ve read that having other devices connected to your Mac while another Mac is connected via TDM can result in corrupted files. Is this true? Is it unsafe to copy files from a TDM Mac to an external USB drive?
    If it is safe, is it best to connect the USB drive to the new Mac or to the old one while it’s in TDM? There’s a lot of data so I’m wondering about transfer times. One method would see files going over Firewire through the new iMac to a USB drive, while the other would go from TDM-connected Mac directly to a USB drive connected to its own USB port. That is:
    TDM iMac > New iMac > USB Drive connected to New iMac
    or
    TDM iMac > USB Drive connected to TDM iMac
    I have limited space on my internal drive and I also don’t want to copy-hop from TDM iMac to New iMac then copy from New iMac to USB drive. I'd like to go directly from old drive to external USB drive if it's safe.
    So I’m looking for advice on the best way to connect devices in order to cut down on copying time and number of copies, and to do it safely without corrupting data. Any advice is appreciated!

    I've used Migration Assistant already to move all of my immediately necessary data and settings over. This other data was on a separate partition and I'm unable to copy all of the data over to my new drive due to lack of space.
    Things are complicated by the fact that I need to change some of my externals over to Time Machine ready backups. Previously I was using 1 TB and a 2 TB drive for TM and another 2 TB drive for general backups/archiving. Now I need to juggle things around so that both 2 TB drives are for TM and the 1 TB is used for archiving.
    An important point I should have mentioned is that I can't use my old iMac normally due to a GPU problem that seizes the system up. This is the reason I can't just copy stuff directly from old iMac to external USBs.
    I'm interested to know if what I described above is safe and if there are any time savings or benefits for copying through my new iMac or connecting the externals directly to the old iMac in TDM.

  • Can't get Target Disk Mode to work with host computer

    Here's the problem. My Powerbook G4 went down a week ago (it's 7 years old) and I suspect the problem is either the hard drive or the portion of the logic board controlling the drive. I also have a Power Mac G4 400 that's running OS 10.4 Tiger. I've been trying to extract some files (that I failed to back up) from the Powerbook via Target Disk Mode using the older Power Mac as the host, however the target disk doesn't show up on the host screen. When I boot up the Powerbook holding the T key, it chimes and the FireWire symbol shows up like it's suppose to, but that's as far as goes. I plan on upgrading to a newer Mac, which would probably work better as a host, but money is a bit tight right now. Any suggestions would be appreciated.

    If the trouble with the Powerbook is either a failed hard drive or a failed hard drive controller, FireWire Target Disk Mode isn't likely to work with any host computer. What you may want to try is installing data recovery software on the desktop G4 and seeing whether it can see the Powerbook's drive (connected in FWTDM) even though it won't mount. Data recovery software is often able to salvage data from drives that won't mount normally; it may be able to do the same thing via FWTDM.
    These three DR utilities are all available in free downloadable demo versions that will show you what the full version would be able to recover before you have to pay for anything:
    Data Rescue
    FileSalvage
    VirtualLab
    Good luck.

  • Can't boot my imac G4 PPC from CD/DVD

    I am trying to upgrade my 10.4.11 OS to 10.5 using a retail DVD but it just won't see the CD drive.
    First it won't read the disk if I put it in it just spits it straight out again
    Then I tried using the startup disk option in preferences but it doesn't list CD/DVD as an option
    Then I tried holding down the option key on startup, it only gives me the HD as an option to start from
    Then I tried holding down the C key
    Then I tried boot cd:,\\:tbxi from openfirmware etc etc etc
    So I know that you can't boot these models from a USB but is it possible they won't boot from CD/DVD drive either
    Grateful for any response
    Anna

    Actually ignore my question it just occurred to me I should see if my DVD drive actually works!!! it doesn't sorry for the bother

  • Can't boot G5 even from OS install disk. Help?

    I've trolled the message boards 25 pages deep and searched all the "Can't boot my G5" threads and still haven't found anyone describing what my machine is doing so thought I'd start a new thread in the hopes someone can help me out.
    Ok I have a G5 dual processor machine. (Power PC chip, not Intel) Things went bad when I tried to do an Archive and Install of Leopard (OS 10.5) The install looked as normal until I got to one minute left on the install. At that point the install never progressed. I thought maybe it was doing some behind the scenes processing and decided to leave it over night. The next day my machine was still hung on that One minute left. So obviously it was a failure. Of course now the problem is I have an install that never completed of the OS and so that partition is, I assume, unbootable. Wiped away the Tiger OS and did a 99% install of Leopard. So I had to shut down by holding the power button.
    I think to myself, "No worries I can just boot from my 2nd partition holding down the Option key to select it on the boot up screen". I always keep a partition with an OS on it for times like these. So I reboot, hold option key, select my other partition, things look OK. I get the grey screen with the Apple logo and I get the wheel animation turning. (Not beachball of death but the typical circular, almost sun ray configuration thing) At this point, usually the screen will go black for a moment before the desktop loads. However, in my case once the screen goes black after the load screen, it stays black. Now let me say the monitor does NOT turn off. There is a definite difference when I manually turn the monitor off. When off it's truly black. But this is like a power on black, not true black. (If you need me to explain this better feel free to ask me to clarify)
    So the untouched, pristine Tiger partition boot is a No Go. I figured I'd then give up on trying to put Leopard on my desktop machine (I use it on my laptop) and reinstall the original OS and system software from the system disk that came with my G5. I boot machine holding down eject button, place the disk in, close the drive door and shut down again by holding power button. Reboot holding C key and the same routine happens with booting from the disk. Gray Apple logo screen, sun ray circle moving, screen goes black on the attempted transition to desktop .. but stays black. I also tried booting with my Disk Warrior disk to no avail. Same thing happens. (Also tried booting from disks by selecting them manually from booting with Option key down) At first I wondered if it was a monitor issue. That maybe my desktop was up but there was an issue with the signal being passed to the monitor on the resolution jump. Thought perhaps hitting the Eject key on the keyboard when I had attempted to boot from the partition (not from disk on this test) would tell me if it was a monitor issue. If it was a monitor issue, the disk tray should open. But alas, no.
    So since I cannot boot normally from any partition or disk I decided to boot into single-user mode.
    I did the fsck -fy thing and it told me everything was ok. I had also previously installed applejack and I ran that and short of correcting a few permissions and dumping some unneeded caches it came back with a system OK.
    At my wits end I booted into target disk mode and ran Disk Warrior on both the original half installed OS partition and the back up emergency boot up partition from my laptop. Again, everything OK. Hoped against hope that I could actually install an OS onto my G5 from my laptop but I was only given the option of being able to do it from my laptop with the Leopard disk and it would only allow me to do it if I used Disk Utility to completely format that drive first. No, thanks.
    Re-attempt to boot G5. Failure. So now I turn to hardware. Disconnected everything beside the keyboard and mouse. Try again. Fail. Pulled a couple sticks of Crucial memory out of the machine and left the stock RAM. No dice. Pressed the small power unit reset button under the RAM slots. No change. Zapped the PRAM. Still nothing. Try to boot in Safe mode holding down shift key. Doesn't work.
    It seems to me if I can't even get the machine to boot from the Install disk that there is something going on that is much more major than software issues.
    Bad motherboard? Any ideas? Because I'm all out of ideas.

    Brother, Sound74, I thought I was the only one pulling the hair out of my chest one by one the past two days. Your situation is very similar to mine, and I'm just as clueless as you are. I started getting kernel panic screens, then nothing on boot, until finally I brought it to the local genius bar. They ran all the usual software/hardware tests, updated Tiger to 10.4.11, recommended I buy Leopard and do an erase-install. My computer, of course, was working absolutely fine by this point. I bought Leopard, came home, backed everything up, then tried to install the new OS. Like in your case, it just up and quit half-way through. Screen went black and a "No DVI Signal" message came on my display (it does this when I turn it on without first turning on the computer).
    So I thought, well, maybe it takes a really long time to erase-install, and the monitor is just waiting for things to kick back in. I've always upgrade-installed before, so I couldn't tell if this was normal or not. But about half an hour later, my fans kicked in so fast I thought I had a P-51 Mustang taking off in my studio. I waited a bit more and finally force-shut-down my system. Not knowing what to expect, I nervously tried to re-boot.
    Nothing. Zip. I can't safe boot, I can't boot from the installer disc, etc. The only thing I can do is the option-key thing whereby you choose the startup disc. And of course, it only gives the Leopard install disc as an option, because now the entire HD has been erased! But when I choose the Leopard disc, of course it doesn't work.
    So I have a nice $3000 paperweight sitting in my studio. I guess I'll have to bring it back to the Mac store, where if it costs more than $300 to fix, I'm going to say screw it and put that dough toward a new iMac.
    Sorry I couldn't provide any helpful info, but I just wanted you to know you're not alone in suffering the slings and arrows of outrageous technology.
    Keep me posted on any solutions you discover, and I'll do the same.
    Noochy1
    PS My applecare expired a month ago! AAAAARRRRGGGHHHH!!! **** Murphy and his stupid laws.

  • Booting an iMac from a PowerMac??

    I have an old PowerMac G4 and a newer, intel-based iMac. No monitor for the G4.
    Just was wondering, is it possible to boot an iMac from a PowerMac?

    It may be possible, but the following IF conditions must be met.
    1. The Power Mac G4 is capable of starting up in FireWire Target Disk Mode.
    http://support.apple.com/kb/HT1661
    2. The startup disk on the Power Mac G4 has Leopard. Leopard is universal. Tiger has separate PowerPC and Intel builds. You won't be able to start up an Intel Mac with PowerPC Tiger.
    3. The startup drive in the Power Mac G4 is the set to master, if it is on an IDE bus that has two drives (as master/slave). FireWire Target Disk Mode will only allow access to the drive set to master.
    4. The Power Mac G4 is able to start up (normally or in target mode) with no display connected.
    If you can do 1-4, connect the Power Mac G4 (in target mode) to the iMac. On the iMac, select the Power Mac's hard drive as the startup disk in System Preferences +Startup Disk+ pane. Restart the iMac.
    For point #4, if the Power Mac G4 is able to start up normally with no display connected, and it has at least Tiger as the OS, please post back. I'm not sure what you are trying to achieve, but there may be a better solution using the screen-sharing feature.

  • Can I install FROM a working iMac TO an iMac in Target Disk Mode?

    Hi.
    I have a distressed iMac - it's in Target Disk Mode (the Firewire logo is on its screen), and it's hooked up to another iMac. I can see and navigate to the distressed Mac's hard drive via the good one. Can I insert the SL install disk on the good mac and install it on the bad one? I've tried the other way...but the distressed iMac stalls out when booting the install disk visa-versa.
    The distressed iMac's internal optical drive is dead, and for some reason it WILL NOT recognized an external firewire/usb optical drive.
    Thanks.

    Sure, the working mac should see the other one as a firewire connected hard drive, nothing more - so long as the working one is an intel, and the target drive is partitioned suitably; 10.6 ought to install no problem.

  • How can I operate my iMac from my Macbook Pro?

    how can I operate my IMAc from my Macbook Pro?

    Explore Target Display Mode:
    https://support.apple.com/kb/PH19038?locale=en_US
    Ciao.

Maybe you are looking for