HT202663 I do not have a Wireless Diagnostics Assistant entry in the drop down WIFI menu of my OS X 10.9.5I

Shortly after updates to OS X 10.9.5 and Safari 7.1 I have been having WIFI failure, after leaving my MacBookPro 15in Late 2008. When I return WIFI is not connected, begins searching unendingly, not finding my network, nor others it always sees. Opening System Preferences just hangs, and must be Force Quit to Restart. Upon any Restart WIFI ALWAYS connects and works.

Troubleshooting Wi-Fi issues in OS X
Wireless Connection Problems - Fix
Wireless Connection Problems - Fix (2)
Wireless Connection Problems - Fix (3)
Wireless Connection Problems - Fix (4)

Similar Messages

  • My Yahoo and Norton toolbars were disabled when I updated today and they did not reset. They no longer appear in the drop down view menu. How do I reset them?

    I was asked to update my Firefox today. The prompts said the yahoo and norton toolbars would be disabled during the update and ENABLED after. They did not reset and do not appear in view drop down menu. How to I reset the toolbars? I am a novice user please be as simple as possible.

    Add-ons are Disabled after Updating Firefox
    * https://support.mozilla.com/en-US/kb/Add-ons%20are%20disabled%20after%20updating%20Firefox
    Check and tell if its working.

  • I have lost all of my bookmarks from the drop-down menu. It says it is empty, but never have I deleted them. And when I bookmark a page it does not save it. Please help

    Question
    I have lost all of my bookmarks from the drop-down menu. It says it is empty, but never have I deleted them. And when I bookmark a page it does not save it. Please help

    Ok this is bizzare!
    Thank you for your response, I went throught each and every step without any luck, even got the recovery programme, and painstakingly tried to sift through all that mumbojumbo to find what i needed. finally found the bookmark bit, but it had been fully overwritten :(, so on reading about previous ff versions, found the sqlite thingys, and they were relatively unscathed(partly written over, but saveable apparently TG), saved them to adiff drive, amongst other possibly good folders. Then looked up how to install them, and it said to close FF, and install to profile folder.
    So i tried to close FF, and the original problem from a few days ago, where it asked me if 'i was sure i wanted to close this window as it has X tabs open', popped up again. This is where 'open blank page' selection was set, over 'open previous tabs'. Wanting to save that info on how to sort out these friggin files, I reset the Option to 'open previous tabs', and closed FF. After unsucessfully searching for the profile folder on my laptop, i opened FF intending to search online for where i could find said folder.
    AND BANG, surprise surprise, the FF I had just closed with only tabs open about finding out what the heck to do, had disappeared, and instead my original saved tabs were up, and my bookmarks are there..... I am gobsmacked! what the heck just happened there???
    I have made 3 back up in different folders now, of those friggin bookmarks. I am weary now tho of shutting it all down.... what if its back to the other pages I had with no bookmarks, tomorrow :(

  • When I delete a name from the address book it does not delete it from the drop down name menu when forwarding a message. How do I remove it from the drop down menu?

    When I delete a name from Address Book it is not removed from the name drop down list when forwarding a message. How can I remove it from the drop down list?

    In Mail go to the Window Menu and select Previous Recipients. Deleting entries from there won't delete them from your Address Book.

  • Back button forward button, refresh and cancel button all do not work they are always grey out and the drop down history by forward arrow doesn't work either

    when I go to another website the back button to the home button never works. the home button works. I can't do any or the above mentioned features

    This can be a problem with the file places.sqlite that stores the bookmarks and the history.
    * http://kb.mozillazine.org/Bookmarks_history_and_toolbar_buttons_not_working_-_Firefox

  • HT2905 i am trying to delete duplcates" from my i-tunes....sounds easy...except I dont have a "show duplicates" in my drop down "view menu" !! help please

    Anyone help?? I am trying to remove duplicates from my Itunes library....looks easy, except I dont have a "show duplicates" tab in the drop down "view " menu !!
    So, what can I do? thanks

    Dear iTunes,
    YOU SUCK.
    Seriously.
    I have used Apple products for quite some time. I have no idea why they keep changing everything that has finally become second nature! It is now MUCH more difficult - create a playlist, show duplicates, etc. Its an absolute mess and I have yet to find anyone who does not have multiple complaints.
    I have this same problem. All information I look up says use "Show duplicates", which I have done many times for years before. But now when my iPad is plugged in, that option is grayed out for me (unable to be clicked on). I went to the Apple store today and the employee couldn't even answer my questions. I am planning to go back sometime with my computer as well and beg for a solid explanation.
    Wouldn't it be nice if these tracks just didn't duplicate? That seems like a proper solution that would suit me well. Until then I just plug in, arrange by song, and go through manually deleting the extras. Often. #wasteoftime #annoying #argh
    Good luck.

  • Adapter Engine NOT in the drop-down list - RFC adapter, Communication Chan

    Hello XI Experts,
    I recently installed IDES (ERP2005) along with XI (NW2004s). I carried out the post installation steps for XI. I set up XI (technical systems, business systems, etc).
    I have started to create an RFC to File XI interface. I have carried out the necessary steps in the Integration Repository and am now setting up the scenario, etc in the Integration Directory.
    I have reached the stage of creating the communication channel of type RFC for the sender system. However, when I do this, the adapter engine is empty i.e. there are no possible entries in the drop-down list. I was expecting to see "Integration Server" as a possible entry.
    Could someone advise me on what I may have missed which leads to this problem?
    Thanks and regards,
    Nicholas.

    Hi,
    You have to get the SWCV from SAP market place.
    Support Packages and Patches -> SAP NetWeaver -> SAP NETWEAVER -> SAP NETWEAVER 2004S -> Entry by Component -> Content PI/XI
    XI CONTENT SAP_BASIS 7.00 / 6.40
    You have to upload the file in the Integration repository
    Best regards
    Omar

  • How do I clear the "drop down menu" of past titles I have searched for?

    How do I clear the drop down menu of titles that have been searched for in the past? Example; If I type in a word such as craig, then craigslist appears in the drop down menu, how do I clear this?

    Use these steps to remove saved (form) data from a drop-down list:
    #click the (empty) input field on the web page to open the drop-down list
    #highlight an entry in the drop-down list
    #press the Delete key (on Mac: Shift+Delete) to remove it.
    *http://kb.mozillazine.org/Deleting_autocomplete_entries

  • I have created a PDF form with multiple drop downs, all with the same drop down values. When I select a value from 1 of the drop down fields, it replicates in all of the others - which I do not want. How can I fix this?

    I have created a PDF form with multiple drop downs, all with the same drop down values. When I select a value from 1 of the drop down fields, it replicates in all of the others - which I do not want. Can I fix this?

    I'm fairly new to this, but I think it has to do with the way you have the drop downs named. Did you copy one then keep pasting it in each field? If so, that is the problem. You should rename each one with a different number: Dropdown1, Dropdown2, etc. I think that might solve the issue.

  • Cannot remove autocomplete entry from address bar; have already cleared history, and entry is not in the drop-down menu of the address bar either.

    I am having problems removing an autocomplete entry from my address bar; I have tried clearing my history, so it's no longer in that, and I do not have it bookmarked either, so it's not getting the URL from that location either. The autocomplete entry isn't even showing up in the drop down menu, so I can't even scroll through that to delete it.
    Basically, I want to be able to type "st" and go to "store.steampowered.com"; however, despite numerous times of typing in "st" and then going down into the drop-down menu to choose "store.steampowered.com", the bar continues to autocomplete "steamtrades.com", which is exceptionally annoying because I do not have that website bookmarked, or in my history, yet it continues to autocomplete to that address, which I do not want it to autocomplete to, and cannot figure out how to remove because I've already cleared my history multiple times, do not have it bookmarked, and it is not showing up in the drop down of the address bar for me to go down and force delete it.

    Did you try to remove some letters from steamtrades.com to see if that bring this entry up in the drop-down list?
    If it is not in the history then it might be present with a typed=1 flag indicating that you have typed or pasted it in the location bar.
    You can use the SQLite Manager extension in Firefox to inspect the places.sqlite file to see if this entry comes up in the moz_places table.
    *SQLite Manager: https://addons.mozilla.org/firefox/addon/sqlite-manager/
    <pre><nowiki>SELECT datetime(visit_date/1000000,'unixepoch') AS visit_date, url, title, visit_count, frecency
    FROM moz_places, moz_historyvisits
    WHERE moz_places.id = moz_historyvisits.place_id AND url LIKE '%steamtrades.com%'</nowiki></pre>

  • I have two faults! 1, an error comes up in Ps CC 2014 "could not apply the saved panel configuration, restring to default and my tools have disappeared completely and anything ive tried I cannot get them back not even the drop down menu in 'window' helps

    I have two faults! 1, an error comes up in Ps CC 2014 "could not apply the saved panel configuration, restring to default and my tools have disappeared completely and anything ive tried I cannot get them back not even the drop down menu in 'window' helps at all. And 2, Lr everytime I load it up it gives me the option to retry or switch to and it takes a while for me to even get anywhere with it I think it has something to do with the catalogs? I've been using these programs for a few years now on a Mac...no problem but when I use a PC when I'm away coz it's the (only) comp available these happen PC's are so useless! Please can anyone help??...

    I can give a few suggestions on Photoshop CC 2014, but Lightroom is a separate forum and you should ask Lr questions there.
    First close Photoshop.
    Then start Photoshop by double-clicking on it's icon and very quickly after that, hold down the ctrl-alt-shift keys until you see the reset dialog. answer "Yes" to delete settings, and let Photoshop continue to load.
    It's tricky to do and may take a few tries, but at least it should reset Photoshop CC 2014 to defaults.
    Gene

  • I have forgot my Iphone passcode. Itunes will not let me restore it, i do not have icloude,or find my iphone,and the closest itunes store is 4 hours away how can i unlock, or reset my phone?

    I have forgot my Iphone passcode. Itunes will not let me restore it, i do not have icloude,or find my iphone,and the closest itunes store is 4 hours away how can i unlock, or reset my phone?

    Try this:
    Placing your device into recovery (DFU-Device Firmware Upgrade) mode:
    Follow these steps to place your iOS device into recovery mode. If your iOS device is already in recovery mode, you can proceed immediately to step 6.
       1. Disconnect the USB cable from the iPhone, iPad, or iPod touch, but leave the
           other end of the cable connected to your computer's USB port.
       2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds
           until the red slider appears, then slide the slider. Wait for the device to turn off.
                  * If you cannot turn off the device using the slider, press and hold the
                    Sleep/Wake and Home buttons at the same time. When the device turns off,
                    release the Sleep/Wake and Home buttons.
      3. While pressing and holding the Home button, reconnect the USB cable to the
           device. The device should turn on. Note: If you see the battery charge warning,
           let the device charge for at least ten minutes to ensure that the battery has some
           charge, and then start with step 2 again.
      4. Continue holding the Home button until you see the "Connect to iTunes" screen.
           When this screen appears you can release the Home button:
      5. If necessary, open iTunes. You should see the following "recovery mode" alert:
      6. Use iTunes to restore the device.
    If you don't see the "Connect to iTunes" screen, try these steps again. If you see the "Connect to iTunes" screen but the device does not appear in iTunes, see this article and its related links.
    Additional Information:
    If you have a problem getting into recovery mode then try: RecBoot: Easy Way to Put iPhone into Recovery Mode.
    Note: When using recovery mode, you can only restore the device. All user content on the device will be erased, but if you had previously synced with iTunes on this computer, you can restore from a previous backup. See this article for more information.

  • Error message Indesign:Either the file does not exist, you do not have read access to it, or use the file in another application.

    I've got problem with opening a file in InDesign. The file type is an InDesign Markup Document. The error message is: Either the file does not exist, you do not have read access to it, or use the file in another application. What's wrong?

  • HT4623 I recently updated my iPhone 5 to iOS 6.1 and lost all of my contacts.  My phone was less than 30 days old and I did not have an account with iCloud prior to the back-up.  Any way to restore my contacts or are they lost forever?

    I recently updated my iPhone 5 to iOS 6.1 and lost all of my contacts.  My phone was less than 30 days old and I did not have an account with iCloud prior to the back-up.  Any way to restore my contacts or are they lost forever?

    I have the exact same problem.  I did the update on my iPhone 5 yesterday, opted for the iCloud set up in the update and then it wiped my contacts.  They are not on my phone or in the cloud...

  • Since installing 10.7.3 my downloads say that I do not have enough space on my computer for the download. These downloads are never more that 200 megs or so and I have 270 Gigs left on my hard drive. What can I do to fix this?

    Since installing 10.7.3 my downloads say that I do not have enough space on my computer for the download. These downloads are never more that 200 megs or so and I have 270 gigs left on my hard drive. Somehow the remaining space on my hard drive is not being correctly read. What can I do to fix this? I have run permissions repair several times, but to no avail.

    Th downloads do not finish. I am dowloading to a file on my desktop called MUSIC, but it first starts to download to my desktop and then I move it to the MUSIC file also on my desktop and I have been doing this without incident using 10.7.2 as well as 10.7.1 and 10.7.

Maybe you are looking for

  • Win 8.1. Core language and multi-language support.

    HI, I've used a US developed program with multi-language support for years in Win XT and Win 7. As the program now supports win 8.1. I've upgraded to 8.1. and the new release of the program. However it will not work properly and the reason given is t

  • Unable to use warp in script - Photoshop CS2

    Hi, I could not warp the image using javascript from Adobe Extendscript interface. This is what I tried. 1) Created an action with warp, converted the action to jsx using xtools. 2) Used Scriptlistener to record ward and used the javascript. When the

  • Can an object be a transaction resource ?

    I have an object named buffer. It has a field named 'Message' Two beans AddToBufferBean and RemoveFromBufferBean operate on the same 'buffer' object. Will this 'buffer' object be considered as a transaction resource ? If no, is there a way to do so ?

  • Console login trouble with Crystal Reports Server XI

    I installed Crystal Reports Server XI on a new box (replacing old), then applied SP1, and then SP2 bringing it up to the same level as the old box - Version Name: BOXIWIN_SP2 Build Number: 11.0.101.8004. However, when I restarted the server and logge

  • Building index on a map element in DPL

    Hi, If I have an entity which has a map in its data elements: @Entity static class Person { @PrimaryKey String ssn; Map<String, String> attributes; where the map takes key value pairs for the person attributes like { ("name","Jane"), ("age", "25") }.