Influence message control with messages generated in ERP
Hello!
Can you use SRM Influence message control to get an error message from ERP?
When creating a SC/PO I would like to get the error message that the minimum order value for a vendor is not reached.
Thanks in advance!
Best regards,
Karin
Hi Karin,
Create a custom message and implement the same in BBP_DOC_CHECK_BADI as said by maria.
Best Regards,
Anil
Similar Messages
-
How can I disable messages generated by Remote Panel?
I created an application (EXE) to server its panel to other network clients.
I used the Tools > Web Publishing Tool to generate a HTML code to create two different web pages to access this application using Web server:
- Embedded (for some users who need visualize the panel in real time).
- Monitor (to display panel snapshots to users updated every 1 second).
I don't need anyone controlling the remote panel, so I used this option:
Tools > Options > Web Server: Browser Access and checked Allow Viewing (not controlling) for every client connected.
Ok, both are working fine. But it a user try to Request control of VI on the Embedded page (right click in the remote panel), the application running in the server displays a message: Denied control request from XXX: Check permissions.
The embedded page stills working fine, but in the Monitor page that message appears in a box (see attached picture below)..
Is there a way to disable all messages in the remote panel? I realized that I need to access the computer where the application EXE is running to close the message.
I'm thinking in two solutions:
- Unable the right click menu in the embedded page to avoid clients request control of the remote panel.
- Run a code in the application to erase messages generated.
Has anyone an idea how to solve this?
Thanks in advance,
Klein
Message Edited by Klein on 08-06-2008 12:54 PM
Attachments:
Remote Panel message.jpg 10 KBHi Dpcamargo,
I'm already using monitor with a delay of 1 second and this doesn't seems real time like remote panel visualization.
But you sent me a good tip: use java code to cancel right clicks at all....
I will try this solution.
Hey, we are both brazilians! So, thank you so much, Dpcamargo. -
How to trap warning messages generated from the background processing?
Hi all,
Following is my requirement, i want to know whether it can be done and how?
The credit management (CM) warning messages generated as a result of the CM background processes, where do the messages go? Can you trap them and include them in an interface control report?
ThanksHi
If it's created a job for that process, you can try to read the log: here you should find all triggered messages, so the warning ones too.
U can try to use fm like BP_JOBLOG_READ or BP_JOBLOG_SHOW in order to get the log.
Max -
Change the default namespace in soap message generated by webservice proxy
I have a requirement where the default namespace generated by the webservice proxy has to be changed. For example, below is a soap request message generated by the proxy:
<env:Envelope xmlns:env="http://schemas.xmlsoap.org/soap/envelope/"
xmlns:xsd="http://www.w3.org/2001/XMLSchema"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xmlns:ns0="http://siebel.com/asi/"
xmlns:ns1="http://www.siebel.com/xml/getAllSecurityValuesResponse/PS"
xmlns:wsu="http://docs.oasis-open.org/wss/2004/01/oasis-200401-wss-wssecurity-utility-1.0.xsd">
<env:Header>
<wsse:Security
xmlns:wsse="http://docs.oasis-open.org/wss/2004/01/oasis-200401-wss-wssecurity-secext-1.0.xsd"
xmlns="http://docs.oasis-open.org/wss/2004/01/oasis-200401-wss-wssecurity-secext-1.0.xsd"
xmlns:env="http://schemas.xmlsoap.org/soap/envelope/"
env:mustUnderstand="1"
xmlns:xmlns="http://schemas.xmlsoap.org/soap/envelope/">
<wsse:UsernameToken
xmlns:wsse="http://docs.oasis-open.org/wss/2004/01/oasis-200401-wss-wssecurity-secext-1.0.xsd"
xmlns="http://docs.oasis-open.org/wss/2004/01/oasis-200401-wss-wssecurity-secext-1.0.xsd">
<wsse:Username>kaoliver</wsse:Username>
<wsse:Password
Type="http://docs.oasis-open.org/wss/2004/01/oasis-200401-wss-username-token-profile-1.0#PasswordText">db2</wsse:Password>
</wsse:UsernameToken>
</wsse:Security>
</env:Header>
<env:Body>
<ns0:SearchSecurityServicegetAllSecurityValues_1>
<Login>kaoliver</Login>
</ns0:SearchSecurityServicegetAllSecurityValues_1>
</env:Body>
</env:Envelope>
In the above message, I want to change the oasis namespace to a different namespace. Where are the default namespaces defined in the proxy classes generated by Jdev so that I can change them?
Thanks in advance,
Warm Regards,
Shashi Anand B>
If I define a prefix P2L in the expression editor to correspond to "http://foo.com/namespace/business", I'm able to reference the ExecuteResponse element as "./P2L:ExecuteResponse", but then I get stuck.
If I try use a Rename action to change the namespace for "./P2L:*", only the ExecuteResponse element is renamed to <sof:ExecutResponse xmlns:sof="http://foo.com/namespace/proxy">. Upstream in the calling application, there's an XML stream reader exception because (I assume) ExecuteResult is not found and parsed.
>
You pattern "./P2L:\*" matches just one element so it's ok that the payload's namespace wasn't touched. If you want to rename namespace for all elements try "//P2L:*". However, I'm not sure whether this is what you want. Try do describe what you do, what you want and what you get instead.
>
I also tried using a Replace action against "./P2L:ExecuteResponse/@xmlns" to replace its contents with "http://foo.com/namespace/proxy". I also tried "./P2L:ExecuteResponse/@P2L:xmlns". Neither worked.
>
I think it's not a good approach to replace content of xmlns as this attribute is not a common xml attribute. -
Suppressing the message generated by standard SAP code
Hi experts,
I have requirement in which i have to suppress the warning message generated by standard SAP code.Is it possible?
If so how?
Any pointers will be highly appreciated.
Thanks,
RakshithHi,
Check with the functional consultant. There might be a config transaction, wherein you can specify the type of error whether Harderror' or warning etc.
I know, Fi and MM has that.
Regards,
Subramanian -
My Messages generated from Photos always lose
Hello to all
A really annoying problem with Mail on iPhone 4 iOS 7 (latest version) :
My messages generated with another App that Message ( especially in Photos ) are almost never reach the recipient and do not appear in the thread of the contact in question. It is as if they never existed ! I confirm sending and nothing happens : no bug , no message , nothing.
I add that I have great difficulty also send messages when I add a picture ( ie when I go through the application Message directly and I'll find a photo secondarily via the camera icon photo). There, I often have a red exclamation point that tells me that it does not pass.
With an iPhone since the first model sold, this is the first time I encountered such a problem. I tried rebooting and it does of course no effect .
This becomes extremely annoying and that's why I ask for your opinion today !
Thank you to those who can help me!
B.
PS : I've already read the FAQ about problems with MessageHello:
I have no idea why it has happened, but try making the devices favorites.
Barry -
Error message generating Adobe Air output Unable to build a valid certificate chain for the signer
error message generating Adobe Air Output: Unable to build a valid certificate chain for the signer.
Are you talking about AIR Help produced by RoboHelp or an AIR application that you are creating?
If the latter, please see the notice at http://forums.adobe.com/community/robohelp/airhelp
If you are using RoboHelp, which version?
See www.grainge.org for RoboHelp and Authoring tips
@petergrainge -
Warning on PO Saving: No message generated for output of purchasing documen
The following message is coming while saving the Purchase Order.
No message generated for output of purchasing document
Message no. 06261
Diagnosis
The system was not able to find a message record via the message determination schema. Therefore it was not possible for such a record to be generated for this purchasing document. In consequence, the purchasing document cannot be outputted (printed or transmitted).
Procedure
The message determination process should be checked and, if necessary, corrected.
The message record can be created manually for this document. For this purpose, choose the function "Messages" in the menu "Header" and maintain the necessary data.
Please guide.
Regards,
AditiHello Aditi,
In messege determination necessary data is not maintained. Goto
MN04, select output type as NEU, then click on key combination and select the last option, then select document type as NB and FUNC as VN and put medium as 1 and in Date / time field 4, language EN and SAVE the data.
This will solve the problem.
Regards.
Sanjay -
Warning "No message generated for output of purchasing document" disabled
Hello Gurus
When a PO in ME21N is created and for some reason there was no output message determined the system should give a warning message "No message generated for output of purchasing document". It causes troubles because buyers don't know when they press SAVE whether output was made or not.
Please advise where to enable this feature.
Note: This happens not always and not for every user.
Great Thanks and Best Regards!Hi Oibek,
This message is automatic , i have not seen any config driving this.
If there is no output message type maintained for document type or requirement is met , system by default issue the warning message 'No message generated for output of purchasing document' .
Check the user GUI setting , may be warning messages are ignored for display.
Logon to SAP -> Customization of Local Layout (ALT+F12)-> Options -> Options tab -> Dailog Box at warning Message ( tick the Check box).
After this try creating PO from user Login , it should display a dialog box even for warning.
Thanking You ,
Sudhakar -
Hi;
I have a problem in GRC-PC I can't solve. My User is generating a 'Dashboard' report on the status of planned for the 1st quarter of 2014 (compliance controls), this controls not planned, but presented the control with status Submitted.
I appreciate any help...
Thanks all....
Regards....kaeandcolesmon,
If you open the recovery drive (partition) it should only have a single folder (Recovery).
To make sure that your not saving restore points to that drive.
See:
Start, Control Panel, System, System Protection tab. Make sure the D drive partition is set to OFF so that it does not save there.
I am a volunteer. I am not an HP employee.
To say THANK YOU, press the "thumbs up symbol" to render a KUDO. Please click Accept as Solution, if your problem is solved. You can render both Solution and KUDO.
The Law of Effect states that positive reinforcement increases the probability of a behavior being repeated. (B.F.Skinner). You toss me KUDO and/or Solution, and I perform better.
(2) HP DV7t i7 3160QM 2.3Ghz 8GB
HP m9200t E8400,Win7 Pro 32 bit. 4GB RAM, ASUS 550Ti 2GB, Rosewill 630W. 1T HD SATA 3Gb/s
Custom Asus P8P67, I7-2600k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX660 2GB, 750W OCZ, 1T HD SATA 6Gb/s
Custom Asus P8Z77, I7-3770k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX670 2GB, 750W OCZ, 1T HD SATA 6Gb/s
Both Customs use Rosewill Blackhawk case.
Printer -- HP OfficeJet Pro 8600 Plus -
Idocs are not equal to XML message generated
hi ,
i am facing problem when i using XI.its not generated idocs equal to XML message generated.idocs equal to XML message
Do u mean that in ur file to idoc scenario, the no of messages sent by file is not equal to no of idocs generated? If yes, then first check in tcode sxmb_moni at XI for presence of message and check for error there
Please describe ur scenario a bit.
Regards,
Prateek -
Suppressing Messages Generated by Function Modules
Hello,
Is there a way to suppress a message generated from within a function module even though the function module doesn't raise an exception to be handled?
I am calling L_TO_CREATE_MULTIPLE and it calls another function module that doesn't raise an exception, it just generates a message. I'd like to be able to handle the message rather than have it displayed to the user.
Thanks for any help anyone could provide.
Best Regards,
BrettBrett,
When I tried it in a normal function module (not RFC), I am not able to suppress the "Information" messages. I have a BDC inside the fn module.
Do you have any idea?
Thanks for your help,
Bala -
Fn on screen display message generator for ThinkPad has stopped working
Hi,
I did a clean install of Windows Vista Enterprise edition and have installed all the drivers for my T400.
What I found was that the Fn on screen display message generator was working fine right before I installed the driver for the Intel GM4500 video controller.
Once I installed this video driver, I get a popup window that says On screen display message generator for Thinkpad has stopped working
The problem details are as follows:
Problem signature:
Problem Event Name: APPCRASH
Application Name: TPOSDSVC.exe
Application Version: 1.1.5.0
Application Timestamp: 49ba1898
Fault Module Name: MMDevApi.dll_unloaded
Fault Module Version: 0.0.0.0
Fault Module Timestamp: 4549bd03
Exception Code: c0000005
Exception Offset: 749c19ad
OS Version: 6.0.6000.2.0.0.256.4
Locale ID: 1033
Additional Information 1: d5a1
Additional Information 2: c4214129afe40788e38f0b75c15ad165
Additional Information 3: ed09
Additional Information 4: 309182ce310d7491a448199eccbd6ba1
I know that some of you have experienced this problem too but so far there hasn't been a solution that's worked.
I'm reluctant to install Vista SP1 or SP2 as that may caus other unrelated problems.
Thanks in advance for any advice you may have.Dear All
Error message on start "on screen display message generator for thinkpad has stopped working"
Event Log "Faulting application TPOSDSVC.exe"
OS Vista Business 32
I have experienced this on a customer's ThinkPad R61e Machine Type 7650-DNG and found that the following solves the problem.
Firstly run Thinkvantage System Update and get everything up to date from Critical, Recommended and Optional Updates tabs.
Next Run Windows Update and view the available updates select all High Priority Microsoft updates and any optional ones that you require and (and this is where it differs from normal Lenovo advice) select the Conexant Audio driver aswell.
Current Vista version available on Windows Update is 4.98 (Date 23 Jun 2009)
Current Vista version available on Thinkvantage System Update is 4.18 (Date 2 Oct 2007)
NB Re-installing 4.18 may have solved the problem also, but I have not tried that and do not plan to.
I hope this helps.
Jason Bolton - BWCL - Lenovo Premium Business Partner - www.bwcl.co.uk -
On screen display message generator for ThinkPad has stopped working
Hello,
This is a fresh install of Vista-32 on a lenovo x300.
Upon boot (or launching TPOSDSVC.exe) I receive the error message in the subject line.
There is an entry in the Application log, here is the jist of it:
Faulting application TPOSDSVC.exe, version 1.1.3.0 faulting module MMDevApi.dll_unloaded
I've uninstalled the On Screen Display application a few times - no luck
-I uninstalled it from add/remove programs then reinstalled it via the Lenovo System Update utility.
I've checked my video drivers - up to date according to lenovo
The problem is presitent under new profiles.
I did some digging online and found a possible fix of altering some reg keys
http://forums.lenovo.com/lnv/board/message?board.id=T_Series_Thinkpads&message.id=28789&query.id=223...
The keys mentioned in that post were non- existent in this computers registry.... ?
I added them .... no dice
thanks in advance
-kirby
Solved!
Go to Solution.Dear All
Error message on start "on screen display message generator for thinkpad has stopped working"
Event Log "Faulting application TPOSDSVC.exe"
OS Vista Business 32
I have experienced this on a customer's ThinkPad R61e Machine Type 7650-DNG and found that the following solves the problem.
Firstly run Thinkvantage System Update and get everything up to date from Critical, Recommended and Optional Updates tabs.
Next Run Windows Update and view the available updates select all High Priority Microsoft updates and any optional ones that you require and (and this is where it differs from normal Lenovo advice) select the Conexant Audio driver aswell.
Current Vista version available on Windows Update is 4.98 (Date 23 Jun 2009)
Current Vista version available on Thinkvantage System Update is 4.18 (Date 2 Oct 2007)
NB Re-installing 4.18 may have solved the problem also, but I have not tried that and do not plan to.
I hope this helps.
Jason Bolton - BWCL - Lenovo Premium Business Partner - www.bwcl.co.uk -
Key differentiation in ERP SAP Finance and Controlling with Other ERP Appli
Hi ALL,
I want to know one important thing in ERP SAP Application, What is the Key differentiation in SAP Finance and controlling with other ERP application like Oracle, PeopleSoft...
And what is the main feature in SAP Finance and controlling with other ERP application. Tell few SAP FICO features compare to other ERP application
thanks
KiranHi ALL,
I am waiting for you reply kindly cooperate in this
thanks
kiran
Maybe you are looking for
-
How do I make it so my phone can send Multimedia messages again? Samsung Intensity II
I'm not sure if this is even where I am supposed to post this, I've been having a few difficulties navigating around the site as it is, so my apologies if it is in the incorrect section or anything. I have a Samsung Intensity II, and up until today i
-
OSB logging using message flow logs the messages to domain admin server log file. is it possible to route the OSB logs to a central logging system such as sys logs?
-
I recently upgraded to Acrobat X Pro 10.1.8. When printing a large PDF (>90 pages) I wanted to print multiple pages on one. But the button to access this option (like the button for poster and booklet) is greyed out. So I deleted the printer and rein
-
Is there a way to erase dates from photos? Smart fill option?
I had an old photo shop program that allowed me to circle the date or anything I wanted removed from the picture and it would smart fill with the background. Does this Adobe Photoshop Elements 13 do the same? If so, how?
-
Greetings, How do I zoom-in on the Timeline? I'm using PSE12. Thanks, Shane.