Laserjet 2605dn color printing problem, Blue/green line on page.

I have an HP color laserjet 2605dn that has started to print a faint,thin  blue/green line from top to bottom about 3 inches in from the entire right edge of every page. I ran the cleaning cycle with no change. Any suggestions on how to correct this?

I have very similar problem on my 2600n which is printing 2 vertical green lines very close together about 1.5 inches from left edge. All toners are in supply override mode with black toner reading: Estimated Pages Remaining 0
Color cartridges contain toner with 329 pp remaining according to supply status page.
Is this problem likely to disappear when toner cartridge(s) are replaced?

Similar Messages

  • Mac Pro (early 2008) NVidia 8800GT display problems (blue/green lines)

    I see others have touched on this topic a bit but not quite the same as my problem
    Every 2 - 3 days, I have to reboot my Mac Pro because my display starts showing the dreaded blue green outlines and lines..
    I've called Apple (of course they are not going to admit that others have this problem) and they told me to reset the PRAM, which I did to no avail of course.
    I've had this card for 3 weeks, and they are telling me that I need to bring my mac pro to the apple store. Yeah right, like I can afford to bring my computer in a for a few days, when that is what I use for work everyday (computer programmer).
    When I asked them to replace the card, they told me I have to bring it in, then I told them they can just send me a refund and keep this crap. Which the support rep said, I can't authorize that. Hah.. Apple is really digging on my last nerves these days.
    I did not have this problem with the stock ATI.
    Any suggestions would be appreciated.. I've run hardware tests off the Apple DVD and using techtool pro, nothing fails.
    I've heard reports that this card is a major dog (slow) in leopard, that the ATI actually out-performs it, anyone else here anything like this?
    My Mac Pro HW:
    Model Name: Mac Pro
    Model Identifier: MacPro3,1
    Processor Name: Quad-Core Intel Xeon
    Processor Speed: 3 GHz
    Number Of Processors: 2
    Total Number Of Cores: 8
    L2 Cache (per processor): 12 MB
    Memory: 8 GB
    Bus Speed: 1.6 GHz
    Boot ROM Version: MP31.006C.B02
    SMC Version: 1.25f4

    What monitor are you using it with? If it's a 30" Cinema, this problem has been around for a couple of years without any resolution - there's a long thread about it in the Displays forum.

  • HP LASERJET CP1525n COLOR PRINTER password problem

    I forgot the login username and password of my HP LASERJET CP1525n COLOR PRINTER due to which i am unable to access the web pannel for administration like setting a new IP etc. Infact, i want to change it's IP setting which is configured to get IP via DHCP. I want to assign a static IP to my printer.
    My printer is on network i.e. directly connected to network switch via network cable.
    Please let me know if there is any solution for that.

    any solution ???

  • How to configure ePrint on LaserJet CP1025nw Color Printer

    Solution found:
    How to Configure HP ePrint on the LaserJet CP1025nw Color Printer
    System:     Windows  (Widows 7)
    Step 1 – Install Printer
    Install the CP1025nw Printer to USB, Wifi or Ethernet.
    (Printer needs to print correctly in order to pass to the next steps).
    Step2 – Check Firmware Version
    Press the “Info-Button” on the CP1025nw LaserJet for five seconds.
    The printer will print two info pages.
    Look at the first Page on the top-left for Firmware Version
    Firmware version must be 20120103 or higher.
    Step 3 – Update Firmware
    Download Firmware Update utility (LJCP1020_FWUpdate_signed.exe) from the following link:
    Utilidad de actualización del firmware de HP LaserJet CP1025nw
    or
    http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=lj-86491-5&cc=es&dlc=es&lc=es&...=
    Execute the Utility on the computer were the CP1025nw LaserJet is correctly installed.
    Find the CP1025nw Printer on the list. The selection Window might show the printer several times depending on how the printer was installed. Select one option and press the button “Update One”.
    Step 4 – Retrieve the Printer Code for your CP1025nw Printer
    ATTENTION:
    The “Host Name” of the printer is not the “Printer-Code” you need  for ePrint setup.
    To retrieve the Printer-Code you must run the ePrint-Setup-Wizard-Utility.
    To download of the utility, go to the link: http://www.hp.com/go/ePrint .
    Find the “HP LaserJet Pro CP1020 Color Printer Series” option in the Drop-Down-List.
    Click “Windows” to download the wizard (EPrintSetupWizard.exe ).
    Execute the Wizard on the computer where the CP1025nw Printer is correctly installed. After running the wizard press the “Info-Button” on the CP1025nw LaserJet for five seconds. The printer will print three info pages. The third info-page offers the Printer-Code you need for ePrint setup. The code is valid for 24h only. When time elapses you have to reprint the info-pages to get an actualized Printer-Code.
    Step 5 – Get Printer Email for your CP1025nw LaserJet
    In order ePrint on your CP1025nw Printer you need to assign an email address to your Printer. To do this, go to the following link: http://www.hpeprintcenter.com/
    Log in with your HP-ID. If you don’t have one, register for a new account.
    When logged in, click on “Add new Printer”-button. You will be asked to enter the Printer-Code. (On how to get the Printer-Code, see step 4).
    While evaluating the Printer-Code, be patient, the program needs its time.
    When the Printer-Code is accepted, you can assign an email address for your CP102nw5 LaserJet. Done this, your con print your CP1025nw Printer just by sending the documents per email to the email-address of your printer.
    Done.

    Hi Max, check out the link below...
    http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?cc=us&lc=en&dlc=en&product=4052972
    Hope this helps
    Ciara
    Although I am an HP employee, I am speaking for myself and not for HP.
    Twitter: @Ciara_B_HP

  • Windows 7 and 8.1 drivers for LaserJet CP1525dw color printer

    I am looking for printer drivers for my HP LaserJet CP1525dw color printer.
    Specifically, I need the drivers for Windows 7 and 8.1, repsectively, if they exist for my color printer.
    If not, how do I continue to use my LaserJet CP1525dw?  It still works very well.
    Thanks.
    NorthTex4912

    Hi @NorthTex4912, 
    I understand that you need the drivers for the Laserjet CP1525. I can help you with this.
    Do you mean the Laserjet CP1525nw? How Do I Find My Model Number or Product Number?
    Here is the URL for the printer drivers. Select your operating system, click next and click on the software to download and install. HP LaserJet Pro CP1525nw Color Printer Drivers.
    If you need further assistance, just let me know.
    Have a nice day!
    Thank You.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

  • Pavilion dv7-4060us Color Printing Problems...

    I just bought a new Pavilion dv7-4060us Notebook and am having problems printing in color.  I have a Xerox Phaser 8550DP PS Printer that I'm trying to connect to through a wireless network connection.  I can find the printer on the network and install the "Xerox Phaser 8550DP PS" driver online just fine.  But, after all that, when I try to print, it will only print in Black and White.  For some reason it just will not print in color.  I've looked through all my "printer properties" and it doesn't even show color options!  It's like my computer just doesn't even recognize that the printer can print colors.  Like maybe that printer's driver is for some reason not recognizing it as that actual printer?!
    I tried deleting the printer and the driver off my computer and installing it using the printer's original CD, but it says it's not compatible with Windows 7 OS.  But installing the driver via online and using the CD should basically be the same thing shouldn't it?  So that can't be the problem.  The "HP printer help website" doesn't really help at all because it's a Xerox printer and not an HP.  After reading through some forum posts I figured maybe it was a firewall problem, but wouldn't the firewall stop me from printing all together...not just prevent me from printing color?  
    Has anyone seen this happen before or heard of anything like this happening?  Right when I got the computer I kind of went through and deleted a few things I thought were Crapware, so the only thing I can think of right now is that maybe I accidentally deleted some kind of software program that lets me print color?!  Which doesn't really make any sense, so I don't think that's it.
    Also, I know it's not a Windows 7 OS problem or my wireless connection because my brother's computer uses Windows 7 and connects through wireless as well, but his can print color just fine.  He set his computer up like a year ago so he can't remember how he set it all up or what he did, so he's kind of useless.
    As of right now the only thing I can think of to do is try posting on this HP help forum and post on the Xerox Printer help forum and see if anyone has any advice for me.  If you have any ideas I'm up for trying anything because I pretty much NEED to be able to print from this computer!!  Any information can help out a lot so just let me know.  Thanks!

    I have exactly the same problem with my dv7-4171us, my husband has the same printer and it print fine on my Xerox but mine only prints in black and white, its very frustrating.  I called HP and after 2 hours on the phone they couldnt fix it either.
    I'm thinking of doing a full "f11" factory restore.  If anyone knows how to fix the color printing problem please let me know.

  • Laserjet 2600n not printing black on one side of page. already cleaned the laser/scanner assembly.

    laserjet 2600n not printing black on one side of page. already cleaned the laser/scanner assembly. i've cleaned the assembly a few times beofre to restor the colors as the printer is in a semi-dusti environment.  after cleaning the printer was fine, then about a week later, the black - and only the black - stopped printing on the right side of the page.  the text is straight across left to right then starts to waver and then then stops altogether.  i tried a different black toner cartidge and the problem remains.

    > so this is strictly a hardware issue as no drivers are involved. Yup. > Still prints all black.   Ok its not the controller. > Still prints all black.   Ok its not the fuser. >  its still prints all black. OK its not the laser itself > it still prints all black. Not that part either. > What else left is there?  Formatter board hasnt been mentioned.  Something is sending a command to the printer that is telling it to open up the doors and charge the entire page.  Normally the laser is responsible for charging the media.  As the media passes over the toner doors it atracts toner particles.  Then as the paper continues it rolls past the fuser where heat melts the particles into permanent place. > The power supply board maybe?   Perhaps but not likely.  If you have a spare you could try it but power supply problems usually result with the machine unable to boot or print correctly, not printing too much as you have described here. > Is there another part you would reccomend I look at?
    You could try the old Halfway test just to verify that the problem is coming from teh laser/toner part of the printer.  http://www.printertechs.com/printer-troubleshooting/halfway-test Your paper may have somehow gotten a staic charge that opposes the charge of the toner, thus auto attracting all particles in range as it passes over the toner doors.  Might want to grab a fresh ream of paper to test and rule somethign crazy like that out. Not very many options left after that.     

  • How to remove dotted green lines in pages 5.2 documents?

    How do i remove dotted green lines in Pages 5.2 documents?

    That's right. Use Pages '09.
    You can export to Pages '09 from Pages 5.2.
    Peter

  • HP Color laserJet CM1015 MFP printing problem

    Till now my HP Color laserJet CM1015 MFP printer was working perfectly and suddenly prints miss aligned colors. Each color prints a little bit below another. I uninstalled printer’s software and reinstalled again but it didn’t help. There is no error messages. Printer’s alignment didn’t help either. Can anyone help me with this problem?
    Inkjet and Laser Printer Supplies
    Printer Cartridge Recycling
    http://www.cartridgeshop.com.au

    Yes I solved the problem. I had to clean the registry of all information regarding this printer. During the installation I noticed interesting thing. The only installation that worked well was from the CD that came with the printer. I've tried downloaded latest version but it didn't install properly and have no idea why.
    Inkjet and Laser Printer Supplies
    Printer Cartridge Recycling
    http://www.cartridgeshop.com.au

  • HP Color LaserJet CP1215 - Color printing - Page prints yellow background

    Good morning --- I don't believe I have posted to this forum before, so I hope someone can help me solve this issue. 
    My CP1215 color LaserJet -
    printing pref set to color-
    printing a document with colored icons, etc. or color photograph
    Results: the "background" or what should be the white area, is yellow - bright yellow.  
    If I switch printing pref to B/W, I get a black/white document or photo.  Of course, no color.
    I have replaced the yellow toner cartridge (HP product) TWICE, the second one just this morning.
    There are NO error messages.
    Tried running the cleaning tool; disconnect/reconnect, etc.  No luck.
    I gave up trying to solve this issue 2 years ago, and have kept the pref set to black/white with no tech issues.
    Now, however, I have the need to print in color, and I would really like to figure out how to correct this problem.
    This printer is a monster - ~30 lbs or more, and I would rather not have to haul it to a computer shop or ship it.
    If anyone out there has had this problem, please let me know how/if you were able to resolve it.  Many thanks.
    Susan - Threecats

    Hi Threecats
    I understand when you print in color you are getting a yellow background.
    I have included a document for troubleshooting the all yellow background printing.
    Print out a configuration page from Solution eight first. This document  will provide steps for cleaning and calibrating the printer. The Print quality troubleshooting page will identify the print cartridge that is causing the issue.
    Let me know the results when you compare it to the one in the document and if the background printed yellow again. Also the Print quality troubleshooting page results.
    What kind of paper are you using?
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

  • HP LaserJet 1525nw color printer - printing question

    I have blue dashed lines 3/4" long printing horizontally in my left margin every 3"?  Anyone have any idea how to fix this.

    This article covers general print quality issue for your printer and should resolve your issue. Give the steps outlined a shot and let us know if it helps. 
    Best of Luck!
    You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

  • Vertical blue green lines on Tecra M display

    I have blue-green vertical lines on my laptop monitor.
    They only seem to be present when I have a white background (such as a web page).
    The lines go away when I move my mouse over the screen and reappear when the cursor moves. I have no lines on video or pictures, just white backgrounds.
    It's really annoying, please help.
    I am using Win XP SP3.
    I have a Nvidia geforce 6600 128M vid card.

    Hey guys, I'm either thinking it's a VGA wire issue or the screen. I want to say VGA cable, bc in MS paint, when I filled the screen with different colors, the only colors that have lines through them are: White, Yellow, Red, and Beige. Orange did as well, but only slightly.
    I tried moving around the screen, same result in all quadrants of the screen. This happens with similar colors in photo's and video. Typing a paper for my classes is really annoying because of these lines, arghghgh. . .

  • Is there any way to fix the "Fatal Error" that my HP LaserJet CP1525nw color printer is having?cc=us

    I am getting a "Fatal Error" when I am trying to install my HP LaserJet CP 1525nw color printer on my new wireless network (using the CD). Anybody have an idea how to fix this?

    Take it in for service.

  • 1 color solid color to red/blue/green constants

    Hi,
    Does anyone know how to convert 1 color. 
    lets say ORANGE.
    its red value = 16448250
    its green value = 29535
    its blue value = 16711680
    is there a way to know what ORANGE and its red/blue/green value?
    i guess to do something like this?
    thanks in advance
    Message Edited by krispiekream on 03-16-2010 11:52 AM
    Best regards,
    Krispiekream
    Solved!
    Go to Solution.

    Try the Color to RGB VI:
    Misha

  • LaserJet and InDesign printing problem

    All of a sudden my CS6 InDesign will not print to LaserJet.

    This is so odd. On this particular problem page, a couple of days ago I replaced the image 3 times and it still gave me a printer error. I copied the page from the 30-page doc onto a new, single page and still had the problem. I deleted the image and still had the problem. There are three text boxes and I deleted them one at a time and each time, all the way down to one text box, I was still having the problem. Tonight I go back to the original 30-page doc., replace the image, and the page printed out fine. Frustrating!

Maybe you are looking for

  • Still problems with georaster

    Hallo, I have posted some days again that I am not able to load georaster or I should say I can load but when I validate my data after loading I always get the error code 13454 (I tried the import procedure and the georasterloader tool with different

  • How to add a sound on some slides?

    How to add a sound on some slides? Not only one slide and not all the slideshow? Is it possible? It must be!

  • ORABPEL-04079 when opening diagram

    I am testing E-Business with OTM and BPEL 10.1.2.0.2. In E-business I launch a process that launch a BPEL process instance. This process finished with error: <faultstring>javax.ejb.EJBException: Transaction was rolled back: timed out I go to bpel con

  • Is Enterprise Library still relevant?

    I am going to port an old C++ application to C# and intend to replace the C++ custom written cross-cutting libraries with third party cross-cutting frameworks/libraries.   In particular, I have been reviewing the Enterprise Library for the past week.

  • DRM Startup error

    Hi, Got a new error on DRM startup. Anybody knows how to deal with it or even where it came from? Our DBA is not available so I will have the service restarted tomorrow. However, I just wanted to know where the error came from. Thanks. The Error is :