MacBook pro doesnt turn on it straus in the white screen with the apple and a circle and themes turns off it starter web i put ultimate lion x version
My computer MacBook pro want turn on it started when input the lion ultimate versión it straus in the white screen with the Apple and the circle ten it goes off
Try starting your computer by holding down the command + R keys, then run disk utility on your hard drive to verify/repair it. Take a look at his link, http://support.apple.com/kb/HT1782
Similar Messages
-
My MacBook Air will not turn on. I get a white screen with the apple logo and a spinning star (search icon). It will spin for hours and never go away unless I power off.
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
Last night I did an update and now when I turn on my macbook it just goes to the white screen with the apple and stays like that. How do I fix this issue?
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
MacBook Air won't start up even though it's fully powered. The white screen with the apple logo appears when I turn it on, then it shuts right back down. Can someone help me?
Hey Msazama30,
First, I would start off your troubleshooting by following the steps in this link:
Mac OS X: Gray screen appears during startup
http://support.apple.com/kb/TS2570
Then, if that doesn't work, try out the information in here:
Step by Step to fix your Mac
https://discussions.apple.com/docs/DOC-3353
Welcome to Apple Support Communities!
All the best,
Delgadoh -
TS1367 My MacBook turned on but is stuck on the white screen with the apple and the loading circle.
My MacBook turned on but is stuck on the white screen with the apple and the loading circle.
Hi there Mpontari,
I would recommend taking a look at the troubleshooting steps found in the article below.
Mac OS X: Gray screen appears during startup
http://support.apple.com/kb/ts2570
-Griff W. -
Hey everyone,
This morning i took my phone out of the charger and everything was normal however, once i got in the car i looked at my phone and realized it was turned off. I tried turning it on again as well but all it does is going to the start up screen (The white screen with the apple logo) and then it turns off again as well. I also put it on the charger but it does the same thing but repeatedly. So it just goes to the white screen and off again. At last i resorted to recovering my phone even if it meant losing all my data. Slow internet connection meant it took all night but in the morning i recovered and everything and got to the last step ( It told me its finished but i should leave my phone connected to itunes and it will pop up there) but all that popped up was an error screen. It still broken but now sometimes when i try to turn it on the same white screen with the logo comes on with a bar under it. this bar fills up a little then the screen goes black again. Is there any other way i can try to fix this?
P.S. There are no apple stores in my area so i took it to one of the phone stores here and even they said they couldnt do anything about itTry:
- iOS: Not responding or does not turn on
- If not successful and you can't fully turn the iPod fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order. -
I have a macbook and when I power it on and then select myself as a user...It won't power up. It stays in the white screen with the apple logo. I am online currently under 'guest user'. Is there anything I can do from the keyboard to fix this??? Help!!!
Could you specify the model of MacBook and the OS X it's running, please? Some of the advice or references vary along with the system, so this could be helpful to formulate a reply. I've never used a Guest User selection, but do have more than one User.
If the computer does not have an optical drive, you may be able to boot it into a recovery disk mode or something; in an attempt to see what is wrong and maybe fix it.
Good luck & happy computing! -
My Macbook starts up, goes to the white screen with the gray apple, the little loading sign loads, and color wheel appears, and DOES NOT STOP PEIROD!
Even when I restart, shut it down; or when it runs down to no battery, when I plug in the power cord for a while, it loads up to the same stinking screen!
PLEASE HELP ME!Restart the computer and immediately hold the option key down.
If the computer boots and you see two hard drive icons, use the arrow key to select the Recovery drive, and press Return.
You will get to a screen that looks like the image here:
http://www.apple.com/osx/recovery/
Select the fourth item and press Return.
In Disk Utility, select the hard drive in the left column, then First Aid, then click on Repair Disk.
When that is done, quit DU and restart the computer. -
Sometimes it will stay at the apple screen and sometimes it just shuts back off. The battery is fully charged.
ashleymay wrote:
I'm pretty sure it's mountain lion. Neither of your links worked tho, but thanks for trying! I'm new to Macs and only really know the basics of how to use it. When I power on and hold the option key I can chose to recover my Mac. What will that do? Will I lose pictures and stuff? I just went to Mexico and all my pics are on there and I'd hate to lose them, also lots of pics of my little boy.
Hmmmm, they are both working for me. What happened when you clicked on the links? Any error messages? -
My MacBook is stuck at the white screen with the apple logo
My MacBook was frozen so I decided to restart it but when I did it got stuck at the apple logo screen. I've tried entering safe mode but it just does the same thing I really needed my computer for a lot of things including some work so I really need help.
I was looking at this and it helped! http://support.apple.com/kb/TS2570
1) Disconnect, test peripheral devices and network cables - didn't work
2) Perform a Safe Boot - didn't work
3) Reset the NVRAM / PRAM - worked, yay! -
Can anyone help?
That's a really bad thing to do. See if it will Safe Boot. Hold the Shift key down at startup. Give it lots of time; it's checking and repairing the drive, if possible. If that won't work, try booting from the Install DVD holding down the C key, open Disk Utility and repair the drive.
For instructions, see "Try Disk Utility" here.
If neither of those works, it's time to restore from a clone or Time Machine, or to use the Install DVD for a reinstall (NOT erase and install.) This will give you new system files while preserving everything else. When you are finished, bring the OS back to 10.6.7 using the Combo Update. Also, check in Software Update for anything else that needs updating. This shouldn't be all that painful.
My procedure for a major OS or Security update
I never run a major update right away. I always wait at least a week or so to see what develops. Most problems I see here are the result either of a specific incompatibility with a third party application or plug-in, or some pre-existing software or hardware issue related to that unique user, which only comes to light due to the stress an update writing many thousands of new files causes. Then, there are occasionally, presumably, as in the instance of font and PDF problems with the 10.6.7 update, bugs in the update itself, which affect the majority of users.
External drives are not that expensive these days. I have two clones on externals and if I'm concerned enough about an update, I can install it on one of these and test it first.
Here's my own updating procedure. Major updates don't come along that often. It's worth going to the trouble to do this.
1. Have a backup so if something does go wrong, you won't be left in big trouble.
2. Verify and if necessary repair the drive from Disk Utility. (To repair, you must be booted from the Install Disc or an external clone.)
3. Disconnect all peripherals except the keyboard and mouse.
4. Download the Combo Update from Apple Downloads. It's generally more reliable to update from the standalone Combo than from Software Update, and the Combo, as it includes all updates from 10.6 onwards, may correct any files that have been corrupted or somehow gone missing.
5. Boot in Safe Boot. Hold the Shift key down at start up. Give it time, it will take longer. (The Safe Boot will also actually check and repair the drive if necessary--and if possible.) Safe Boot loads a stripped down system which may reduce any chance of incompatibility while the update is running. Keep all Applications closed.
6. Repair Permissions from Disk Utility while booted in Safe Boot.
7. Install the update from Safe Boot. Keep all Applications closed.
8. Restart when prompted and give the system up to five minutes to finish the final touches of the update with all Applications closed.
9. Verify the Drive and Repair Permissions again.
10. And then I like to restart again.
One other caution. If you are running updates from Software Update, run them one at a time, never all at once. This gives the system a chance to assimilate each one, especially if restarts are involved, and not choke on them.
I also prefer to get "non-major" updates as standalones from Apple Downloads, rather than from Software Update. -
HI
this happened today suddenly while i was working on my iPad it kicked my out of the app that i was using then white screen with black apple logo came out, i thought it was an ordinary thing cause this happens all the time with me, but this time it refused to turn on! After the white screen with the black logo vanished i wad waiting for my lock screen but no, a black screen showed up just like that! And could tell it was black "lighten" screen i tried more than 10 times to do the home+power thing but it wont work, whats wrong with my ipad!If the battery is completely drained it may take some time while on the charger before the iPad responds. Plug the iPad into the charger that came with it and plug that into a good wall outlet. Wait one hour. Then reset your device. Press and hold the Home and Sleep buttons simultaneously until the Apple logo appears. Let go of the buttons and let the device restart. If the iPad restarts let it continue to charge until the battery is 100%. If it doesn't start up make an appointment at an Apple Store to have your device examined by a technician. Or contact Apple Support. They will examine your iPad and explain your options.
-
When my Mac battery dies and I turn it back on, it always crashes on the grey screen with the progress bar, then it restarts (taking forever) and does not remember any of the programs I was running. MacBook Pro 13 inch running Mavericks
http://osxdaily.com/2014/10/17/os-x-yosemite-installation-stuck/
also use the Command-L to view logs during installation -
Hello as mentionned before I cannot get my macbook pro to switch on.
when it is not plugged as I press the power button nothing happens, when the computer is power plugged, it gives me the white blackground with the apple centered and the loading button below but it keeps loading forever left it as for 4 hours and still nothing.
I have try to reset the SMC but didn't change much, now instead of the apple logo I get a circle crossed
My macbook is 1 year and 4monthsSee Gray Screen, try holding the Shift key upon boot
Cheat sheet to help diagnose and fix your Mac
Drive may not boot, but if it's still working then data can be recovered
Data recovery efforts explained
Most commonly used backup methods explained -
How do I fix a initializing problem with my macbook pro? I only get to the blank screen with the apple logo and the "processing something" sign... it just doesn't start the system....
Please help
MarceloIf there is no loading bar, it's usually a problem with a third party kext file in OS X itself.
You can press the power button down to force a hardware shutdown, then reboot holding the shift key down on a wired or built in keyboard, this will disable them and you go around and update your third party software.
Gray, Blue or White screen at boot, w/spinner/progress bar
Also take this time to backup your users files off the machine if possible.
Most commonly used backup methods
Sometime that won't work and you need to do more
..Step by Step to fix your Mac
Maybe you are looking for
-
Is there only ones size of card you can get?
I was making a card on iphoto, and the only size available was 7" x 5". Is that the only size?
-
hi experts i have created a custom menu item using following steps esign Console > Form Information > add new Class Name Organizations.Merge Description Move users from one organization to another Type menuitem Add following to xlWebAdmin.properties,
-
Very Urgent My project STOP !!!!!!!!!
Hi I have big problem with report 9i , I have field on my form has mixed numbers with characters When i print in PDF format that field on my report it show me starnge ordering of that numbers and characters , HOW I can solve it ? Original Field :98IS
-
Error message Owl Orphanage : Photoshop:exe-Bad Image
I am having this error with Adobe Photoshop CS5. With reading other posts I found an answer to this same question posted - except with CS4. It mentioned the Plug-in folder and 32 bit and 64 bit. Here is where I get confused. I pulled plug-ins over fr
-
Regarding INVITE retransmission (BEA sip server)
Hi all, I have a question about the WebLogic SIP server (version 3.1) behavior. I am testing a simple call scenario from UAC to UAS on UDP transport (please see the call flow below). It seems that the WebLogic SIP server generated a retransmission of