Reason Code:23 Reason: An error occurred during the Network Policy Server use of the Extensible Authentication Protocol EAP

I get the above described error when trying to connect to NPS 2012 with a Windows XP machine
I successfully connecting to that server with an Android phone.
I started examining the problem and saw the following:
1. The android phone uses some cipher suites that are not supported in Windows XP and the one that theserver selects in  the Server Hello message is Cipher Suite: TLS_ECDHE_RSA_WITH_AES_256_CBC_SHA 0xc014
2. With the WINXP the selected cipher suite is Cipher Suite: TLS_RSA_WITH_AES_256_CBC_SHA 0x0035 and it fails with the above error.
3. Next step I did was to restrict the NPS to use only the Cipher Suite: TLS_RSA_WITH_AES_256_CBC_SHA 0x0035 and not to my surprise the Android phone could not connect and I was getting the same error as with the WINXP.
Any solution to this prpoblem?

Hi and thanks for replying
I do not believe there is a problem with the certificate as it uses the same certificate in both authentication processes - the failed one using the TLS_RSA_WITH_AES_256_CBC_SHA
cipher suit and the successfull one using TLS_ECDHE_RSA_WITH_AES_256_CBC_SHA
cipher suit - so I believe the reason lies elsewhere.
Please check it and try to produce a solution for it.
Thanks

Similar Messages

  • An error occurred during the Network Policy Server use of the Extensible Authentication Protocol (EAP).

    Hello everyone:
    I know this question have been asked in these forums quite a few times. I apologize if it is a repeat telecast but I was not able to find a suitable solution pertaining to my problem.
    I have a AP/SM setup that is configured to get EAP-PEAP authentication from Windows 2012 Server. I have setup everything and have verified that the EAP-PEAP authentication works fine on AP/SM by getting authentication from FreeRADIUS server. Now, when I try
    to get authentication from Windows Server, I am getting a reject. The Event log shows this generic message:
    Reason Code: 23
    Reason:
        An error occurred during the Network Policy Server use of the Extensible Authentication Protocol (EAP). Check EAP log files for EAP errors.
    There is nothing in the EAP logs that is obvious too:
    "USIL01PMPTST01","IAS",07/11/2014,11:59:44,1,"SANDBOX\test","SANDBOX\test",,,,,,"10.120.133.10",5,0,"10.120.133.10","Canopy_AP",,,18,,,,5,"PEAP_TEST",0,"311 1 10.120.133.1
    07/11/2014 00:05:57 4927",,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,"PEAP_TEST_CONNECTION",1,,,,
    "USIL01PMPTST01","IAS",07/11/2014,11:59:44,11,,"SANDBOX\test",,,,,,,,0,"10.120.133.10","Canopy_AP",,,,,,,5,"PEAP_TEST",0,"311 1 10.120.133.1 07/11/2014 00:05:57 4927",30,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,"PEAP_TEST_CONNECTION",1,,,,
    "USIL01PMPTST01","IAS",07/11/2014,11:59:44,1,"SANDBOX\test","SANDBOX\test",,,,,,"10.120.133.10",5,0,"10.120.133.10","Canopy_AP",,,18,,,,5,"PEAP_TEST",0,"311 1 10.120.133.1
    07/11/2014 00:05:57 4928",,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,"PEAP_TEST_CONNECTION",1,,,,
    "USIL01PMPTST01","IAS",07/11/2014,11:59:44,11,,"SANDBOX\test",,,,,,,,0,"10.120.133.10","Canopy_AP",,,,,,,5,"PEAP_TEST",0,"311 1 10.120.133.1 07/11/2014 00:05:57 4928",30,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,"PEAP_TEST_CONNECTION",1,,,,
    "USIL01PMPTST01","IAS",07/11/2014,11:59:44,1,"SANDBOX\test","SANDBOX\test",,,,,,"10.120.133.10",5,0,"10.120.133.10","Canopy_AP",,,18,,,,11,"PEAP_TEST",0,"311 1 10.120.133.1
    07/11/2014 00:05:57 4929",,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,"PEAP_TEST_CONNECTION",1,,,,
    "USIL01PMPTST01","IAS",07/11/2014,11:59:44,3,,"SANDBOX\test",,,,,,,,0,"10.120.133.10","Canopy_AP",,,,,,,11,"PEAP_TEST",23,"311 1 10.120.133.1 07/11/2014 00:05:57 4929",,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,"PEAP_TEST_CONNECTION",1,,,,
    So, basically, the sequence is this:
    request , challenge, request , challenge, request, reject
    Any idea what might be happening?
    Thank you.

    Hi,
    Have you installed certificates on the NPS server properly? Have you selected the proper certificate in the properties of PEAP?
    Here is an article about the Certificate requirements of PEAP,
    Certificate requirements when you use EAP-TLS or PEAP with EAP-TLS
    http://support.microsoft.com/kb/814394
    If your certificate matches the requirement, you may try to reinstall the certificate by export and import.
    To export a certificate, please follow the steps below,
    Open the Certificates snap-in for a user, computer, or service.
    In the console tree under the logical store that contains the certificate to export, click
    Certificates.
    In the details pane, click the certificate that you want to export.
    On the Action menu, point to
    All Tasks, and then click Export.
    In the Certificate Export Wizard, click No, do not export the private key. (This option will appear only if the private key is marked as exportable and you have access to the private key.)
    Provide the following information in the Certificate Export Wizard:
    Click the file format that you want to use to store the exported certificate: a DER-encoded file, a Base64-encoded file, or a PKCS #7 file.
    If you are exporting the certificate to a PKCS #7 file, you also have the option to include all certificates in the certification path.
    If required, in Password, type a password to encrypt the private key you are exporting. In
    Confirm password, type the same password again, and then click
    Next.
    In File name, type a file name and path for the PKCS #7 file that will store the exported certificate and private key. Click
    Next, and then click Finish.
    To import a certificate, please follow the steps below,
    Open the Certificates snap-in for a user, computer, or service.
    In the console tree, click the logical store where you want to import the certificate.
    On the Action menu, point to
    All Tasks, and then click Import to start the Certificate Import Wizard.
    Type the file name containing the certificate to be imported. (You can also click
    Browse and navigate to the file.)
    If it is a PKCS #12 file, do the following:
    Type the password used to encrypt the private key.
    (Optional) If you want to be able to use strong private key protection, select the
    Enable strong private key protection check box.
    (Optional) If you want to back up or transport your keys at a later time, select the
    Mark key as exportable check box.
    Do one of the following:
    If the certificate should be automatically placed in a certificate store based on the type of certificate, click
    Automatically select the certificate store based on the type of certificate.
    If you want to specify where the certificate is stored, select
    Place all certificates in the following store, click
    Browse, and choose the certificate store to use.
    If issue persists, you may try to re-issue the certificate.
    For detailed procedure, you may refer to the similar threads below,
    Having issues getting PEAP with EAP-MSCHAP v2 working on Windows 2008 R2
    http://social.technet.microsoft.com/Forums/windowsserver/en-US/c66cf0a8-24dd-4ccd-b5bb-16bd28ad8d4c/having-issues-getting-peap-with-eapmschap-v2-working-on-windows-2008-r2?forum=winserverNAP
    Hope this helps.
    Steven Lee
    TechNet Community Support

  • ADF:--Error occurred during initialization of VM,Could not create the Java

    Hi Friends,
    when am creating new adf page and starting Run the ADF page it will through an error
    *** Using port 7101 ***
    "C:\Users\Rama Krishna\AppData\Roaming\JDeveloper\system11.1.1.3.37.56.60\DefaultDomain\bin\startWebLogic.cmd"
    [waiting for the server to complete its initialization...]
    JAVA Memory arguments: -Xms256m -Xmx512m -XX:CompileThreshold=8000 -XX:PermSize=128m -XX:MaxPermSize=512m
    WLS Start Mode=Development
    CLASSPATH=D:\Oracle\MIDDLE~1\WLSERV~1.3\server\ext\jdbc\oracle\11g\ojdbc6dms.jar;D:\Oracle\MIDDLE~1\patch_wls1033\profiles\default\sys_manifest_classpath\weblogic_patch.jar;D:\Oracle\MIDDLE~1\patch_jdev1111\profiles\default\sys_manifest_classpath\weblogic_patch.jar;D:\Oracle\MIDDLE~1\JDK160~1\lib\tools.jar;D:\Oracle\MIDDLE~1\WLSERV~1.3\server\lib\weblogic_sp.jar;D:\Oracle\MIDDLE~1\WLSERV~1.3\server\lib\weblogic.jar;D:\Oracle\MIDDLE~1\modules\features\weblogic.server.modules_10.3.3.0.jar;D:\Oracle\MIDDLE~1\WLSERV~1.3\server\lib\webservices.jar;D:\Oracle\MIDDLE~1\modules\ORGAPA~1.1/lib/ant-all.jar;D:\Oracle\MIDDLE~1\modules\NETSFA~1.0_1/lib/ant-contrib.jar;D:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.jrf_11.1.1\jrf.jar;D:\Oracle\MIDDLE~1\WLSERV~1.3\common\derby\lib\derbyclient.jar;D:\Oracle\MIDDLE~1\WLSERV~1.3\server\lib\xqrl.jar
    PATH=D:\Oracle\MIDDLE~1\patch_wls1033\profiles\default\native;D:\Oracle\MIDDLE~1\patch_jdev1111\profiles\default\native;D:\Oracle\MIDDLE~1\WLSERV~1.3\server\native\win\32;D:\Oracle\MIDDLE~1\WLSERV~1.3\server\bin;D:\Oracle\MIDDLE~1\modules\ORGAPA~1.1\bin;D:\Oracle\MIDDLE~1\JDK160~1\jre\bin;D:\Oracle\MIDDLE~1\JDK160~1\bin;E:\oracle\product\10.2.0\db_1\bin;C:\orant\bin;C:\Windows\system32;C:\Windows;C:\Windows\System32\Wbem;C:\Windows\System32\WindowsPowerShell\v1.0\;C:\Program Files\SSH Communications Security\SSH Secure Shell;D:\Oracle\MIDDLE~1\WLSERV~1.3\server\native\win\32\oci920_8
    * To start WebLogic Server, use a username and *
    * password assigned to an admin-level user. For *
    * server administration, use the WebLogic Server *
    * console at http:\\hostname:port\console *
    starting weblogic with Java version:
    java version "1.6.0_18"
    Java(TM) SE Runtime Environment (build 1.6.0_18-b07)
    Java HotSpot(TM) Client VM (build 16.0-b13, mixed mode)
    Starting WLS with line:
    D:\Oracle\MIDDLE~1\JDK160~1\bin\java -client -Xms256m -Xmx512m -XX:CompileThreshold=8000 -XX:PermSize=128m -XX:MaxPermSize=512m -Dweblogic.Name=DefaultServer -Djava.security.policy=D:\Oracle\MIDDLE~1\WLSERV~1.3\server\lib\weblogic.policy -Djavax.net.ssl.trustStore=C:\Oracle\Middleware\wlserver_10.3\server\lib\DemoTrust.jks -Dweblogic.nodemanager.ServiceEnabled=true -Xverify:none -da -Dplatform.home=D:\Oracle\MIDDLE~1\WLSERV~1.3 -Dwls.home=D:\Oracle\MIDDLE~1\WLSERV~1.3\server -Dweblogic.home=D:\Oracle\MIDDLE~1\WLSERV~1.3\server -Djps.app.credential.overwrite.allowed=true -Ddomain.home=C:\Users\RAMAKR~1\AppData\Roaming\JDEVEL~1\SYSTEM~1.60\DEFAUL~1 -Dcommon.components.home=D:\Oracle\MIDDLE~1\ORACLE~1 -Djrf.version=11.1.1 -Dorg.apache.commons.logging.Log=org.apache.commons.logging.impl.Jdk14Logger -Djrockit.optfile=D:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.jrf_11.1.1\jrocket_optfile.txt -Doracle.domain.config.dir=C:\Users\RAMAKR~1\AppData\Roaming\JDEVEL~1\SYSTEM~1.60\DEFAUL~1\config\FMWCON~1 -Doracle.server.config.dir=C:\Users\RAMAKR~1\AppData\Roaming\JDEVEL~1\SYSTEM~1.60\DEFAUL~1\config\FMWCON~1\servers\DefaultServer -Doracle.security.jps.config=C:\Users\RAMAKR~1\AppData\Roaming\JDEVEL~1\SYSTEM~1.60\DEFAUL~1\config\fmwconfig\jps-config.xml -Djava.protocol.handler.pkgs=oracle.mds.net.protocol -Digf.arisidbeans.carmlloc=C:\Users\RAMAKR~1\AppData\Roaming\JDEVEL~1\SYSTEM~1.60\DEFAUL~1\config\FMWCON~1\carml -Digf.arisidstack.home=C:\Users\RAMAKR~1\AppData\Roaming\JDEVEL~1\SYSTEM~1.60\DEFAUL~1\config\FMWCON~1\arisidprovider -Dweblogic.alternateTypesDirectory=D:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.ossoiap_11.1.1,D:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.oamprovider_11.1.1 -Dweblogic.jdbc.remoteEnabled=false -Dwsm.repository.path=C:\Users\RAMAKR~1\AppData\Roaming\JDEVEL~1\SYSTEM~1.60\DEFAUL~1\oracle\store\gmds -Xms512m -Xmx512m -Dweblogic.management.discover=true -Dwlw.iterativeDev= -Dwlw.testConsole= -Dwlw.logErrorsToConsole= -Dweblogic.ext.dirs=D:\Oracle\MIDDLE~1\patch_wls1033\profiles\default\sysext_manifest_classpath;D:\Oracle\MIDDLE~1\patch_jdev1111\profiles\default\sysext_manifest_classpath weblogic.Server
    Error occurred during initialization of VM
    Could not reserve enough space for object heap
    Could not create the Java virtual machine.
    Process exited.
    could you please tell me anybody solve this error.
    Thank and Regards
    Rkrao

    Hi
    am facing same issue, My problem was not solve
    error like this
    *** Using port 7101 ***
    "C:\Users\Rama Krishna\AppData\Roaming\JDeveloper\system11.1.1.3.37.56.60\DefaultDomain\bin\startWebLogic.cmd"
    [waiting for the server to complete its initialization...]
    JAVA Memory arguments: -Xms256m -Xmx512m -XX:CompileThreshold=8000 -XX:PermSize=128m  -XX:MaxPermSize=512m
    WLS Start Mode=Development
    CLASSPATH=D:\Oracle\MIDDLE~1\WLSERV~1.3\server\ext\jdbc\oracle\11g\ojdbc6dms.jar;D:\Oracle\MIDDLE~1\patch_wls1033\profiles\default\sys_manifest_classpath\weblogic_patch.jar;D:\Oracle\MIDDLE~1\patch_jdev1111\profiles\default\sys_manifest_classpath\weblogic_patch.jar;D:\Oracle\MIDDLE~1\JDK160~1\lib\tools.jar;D:\Oracle\MIDDLE~1\WLSERV~1.3\server\lib\weblogic_sp.jar;D:\Oracle\MIDDLE~1\WLSERV~1.3\server\lib\weblogic.jar;D:\Oracle\MIDDLE~1\modules\features\weblogic.server.modules_10.3.3.0.jar;D:\Oracle\MIDDLE~1\WLSERV~1.3\server\lib\webservices.jar;D:\Oracle\MIDDLE~1\modules\ORGAPA~1.1/lib/ant-all.jar;D:\Oracle\MIDDLE~1\modules\NETSFA~1.0_1/lib/ant-contrib.jar;D:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.jrf_11.1.1\jrf.jar;D:\Oracle\MIDDLE~1\WLSERV~1.3\common\derby\lib\derbyclient.jar;D:\Oracle\MIDDLE~1\WLSERV~1.3\server\lib\xqrl.jar;%classpath%;.\
    PATH=D:\Oracle\MIDDLE~1\patch_wls1033\profiles\default\native;D:\Oracle\MIDDLE~1\patch_jdev1111\profiles\default\native;D:\Oracle\MIDDLE~1\WLSERV~1.3\server\native\win\32;D:\Oracle\MIDDLE~1\WLSERV~1.3\server\bin;D:\Oracle\MIDDLE~1\modules\ORGAPA~1.1\bin;D:\Oracle\MIDDLE~1\JDK160~1\jre\bin;D:\Oracle\MIDDLE~1\JDK160~1\bin;E:\oracle\product\10.2.0\db_1\bin;C:\orant\bin;C:\Windows\system32;C:\Windows;C:\Windows\System32\Wbem;C:\Windows\System32\WindowsPowerShell\v1.0\;D:\Oracle\Middleware\jdk160_18\bin\javac;D:\Oracle\MIDDLE~1\WLSERV~1.3\server\native\win\32\oci920_8
    *  To start WebLogic Server, use a username and   *
    *  password assigned to an admin-level user.  For *
    *  server administration, use the WebLogic Server *
    *  console at http:\\hostname:port\console        *
    starting weblogic with Java version:
    java version "1.6.0_18"
    Java(TM) SE Runtime Environment (build 1.6.0_18-b07)
    Java HotSpot(TM) Client VM (build 16.0-b13, mixed mode)
    Starting WLS with line:
    D:\Oracle\MIDDLE~1\JDK160~1\bin\java -client   -Xms256m -Xmx512m -XX:CompileThreshold=8000 -XX:PermSize=128m  -XX:MaxPermSize=512m -Dweblogic.Name=DefaultServer -Djava.security.policy=D:\Oracle\MIDDLE~1\WLSERV~1.3\server\lib\weblogic.policy -Djavax.net.ssl.trustStore=C:\Oracle\Middleware\wlserver_10.3\server\lib\DemoTrust.jks -Xms512m -Dweblogic.nodemanager.ServiceEnabled=true  -Xverify:none  -da -Dplatform.home=D:\Oracle\MIDDLE~1\WLSERV~1.3 -Dwls.home=D:\Oracle\MIDDLE~1\WLSERV~1.3\server -Dweblogic.home=D:\Oracle\MIDDLE~1\WLSERV~1.3\server  -Djps.app.credential.overwrite.allowed=true -Ddomain.home=C:\Users\RAMAKR~1\AppData\Roaming\JDEVEL~1\SYSTEM~1.60\DEFAUL~1 -Dcommon.components.home=D:\Oracle\MIDDLE~1\ORACLE~1 -Djrf.version=11.1.1 -Dorg.apache.commons.logging.Log=org.apache.commons.logging.impl.Jdk14Logger -Djrockit.optfile=D:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.jrf_11.1.1\jrocket_optfile.txt -Doracle.domain.config.dir=C:\Users\RAMAKR~1\AppData\Roaming\JDEVEL~1\SYSTEM~1.60\DEFAUL~1\config\FMWCON~1 -Doracle.server.config.dir=C:\Users\RAMAKR~1\AppData\Roaming\JDEVEL~1\SYSTEM~1.60\DEFAUL~1\config\FMWCON~1\servers\DefaultServer -Doracle.security.jps.config=C:\Users\RAMAKR~1\AppData\Roaming\JDEVEL~1\SYSTEM~1.60\DEFAUL~1\config\fmwconfig\jps-config.xml -Djava.protocol.handler.pkgs=oracle.mds.net.protocol  -Digf.arisidbeans.carmlloc=C:\Users\RAMAKR~1\AppData\Roaming\JDEVEL~1\SYSTEM~1.60\DEFAUL~1\config\FMWCON~1\carml  -Digf.arisidstack.home=C:\Users\RAMAKR~1\AppData\Roaming\JDEVEL~1\SYSTEM~1.60\DEFAUL~1\config\FMWCON~1\arisidprovider -Dweblogic.alternateTypesDirectory=D:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.ossoiap_11.1.1,D:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.oamprovider_11.1.1  -Dweblogic.jdbc.remoteEnabled=false -Dwsm.repository.path=C:\Users\RAMAKR~1\AppData\Roaming\JDEVEL~1\SYSTEM~1.60\DEFAUL~1\oracle\store\gmds  -Xms512m -Xmx512m -Dweblogic.management.discover=true  -Dwlw.iterativeDev= -Dwlw.testConsole= -Dwlw.logErrorsToConsole= -Dweblogic.ext.dirs=D:\Oracle\MIDDLE~1\patch_wls1033\profiles\default\sysext_manifest_classpath;D:\Oracle\MIDDLE~1\patch_jdev1111\profiles\default\sysext_manifest_classpath  weblogic.Server
    Error occurred during initialization of VM
    Could not create the Java virtual machine.
    Could not reserve enough space for object heap
    Process exited.could u please tell me any body, solve this problem
    Thank and Regards
    Rkrao.

  • An internal error occurred during: "Starting BEA WebLogic Server v8.1 at lo

    Hi,
    On "Start the server in debug mode"
    file .log
    eclipse.buildId=I20090611-1540
    java.version=1.6.0_13
    java.vendor=Sun Microsystems Inc.
    BootLoader constants: OS=win32, ARCH=x86, WS=win32, NL=es_AR
    Command-line arguments: -os win32 -ws win32 -arch x86
    !ENTRY org.eclipse.core.jobs 4 2 2009-08-05 12:29:57.060
    !MESSAGE An internal error occurred during: "Starting BEA WebLogic Server v8.1 at localhost".
    !STACK 0
    java.lang.NullPointerException
         at oracle.eclipse.tools.weblogic.legacy.GenericWeblogicServerBehaviour.findWorkshopJspDebuggerLaunchConfigurationDelegate(GenericWeblogicServerBehaviour.java:477)
         at oracle.eclipse.tools.weblogic.legacy.GenericWeblogicServerBehaviour.setupLaunch(GenericWeblogicServerBehaviour.java:226)
         at org.eclipse.jst.server.generic.core.internal.ExternalLaunchConfigurationDelegate.launch(ExternalLaunchConfigurationDelegate.java:101)
         at org.eclipse.debug.internal.core.LaunchConfiguration.launch(LaunchConfiguration.java:853)
         at org.eclipse.debug.internal.core.LaunchConfiguration.launch(LaunchConfiguration.java:703)
         at org.eclipse.debug.internal.core.LaunchConfiguration.launch(LaunchConfiguration.java:696)
         at org.eclipse.wst.server.core.internal.Server.startImpl2(Server.java:3057)
         at org.eclipse.wst.server.core.internal.Server.startImpl(Server.java:3007)
         at org.eclipse.wst.server.core.internal.Server$StartJob.run(Server.java:294)
         at org.eclipse.core.internal.jobs.Worker.run(Worker.java:55)
    OS= Windows XP SP2
    Eclipse Java Version= 1.6.0_13
    Workspace Java Version= 1.4.2_08
    BEA Weblogic= 8.1.6
    Eclipse= 3.5.0
    WTP= 3.1.0
    Project Facets= Dynamic Web Module 2.3
    Java= 1.4
    Tanks and sorry my English.
    Gustavo

    I am also experiencing the same NullPointerException when launching Weblogic 8.1 in debug mode within Eclipse 3.5. Is there any anticipated fix for this issue, or a bugtraq record that we can follow to know when the issue is addressed? I do not expect JSP debugging to work (as it wasn't available with Weblogic 8.1 under Eclipse 3.4 either) - BUT right now I cannot debug ANY server-side code within Weblogic 8.1 in Eclipse 3.5 as the server cannot start in debug mode at all.
    Many thanks.

  • The client could not be authenticated because the Extensible Authentication Protocol (EAP) Type cannot be processed by the server

    wireless authentication not working 
    I found the following in the radius
    Log Name:      Security
    Source:        Microsoft-Windows-Security-Auditing
    Date:          1/15/2014 2:07:57 AM
    Event ID:      6273
    Task Category: Network Policy Server
    Level:         Information
    Keywords:      Audit Failure
    User:          N/A
    Computer:     NAP01.test.local
    Description:
    Network Policy Server denied access to a user.
    Contact the Network Policy Server administrator for more information.
    User:
     Security ID:   doamin \user.a
     Account Name:   user.a
    Client Machine:
     Security ID:   NULL SID
     Account Name:   -
     Fully Qualified Account Name: -
     OS-Version:   -
     Called Station Identifier:  00-0F-7D-C4-45-20:staff
     Calling Station Identifier:  0C-74-C2-EF-Dd-0B
    NAS:
     NAS IPv4 Address:  192.168.9.10
     NAS IPv6 Address:  -
     NAS Identifier:   -
     NAS Port-Type:   Wireless - IEEE 802.11
     NAS Port:   497
    RADIUS Client:
     Client Friendly Name:  wcont1
     Client IP Address:   192.168.9.10
    Authentication Details:
     Connection Request Policy Name: Wireless
     Network Policy Name:  wism
     Authentication Provider:  Windows
     Authentication Server:  NAP01.test.local
     Authentication Type:  EAP
     EAP Type:   -
     Account Session Identifier:  -
     Logging Results:   Accounting information was written to the local log file.
     Reason Code:   22
     Reason:    The client could not be authenticated  because the Extensible Authentication Protocol (EAP) Type cannot be processed by the server.
    Please help

    Hi,
    Anything updates?
    In addition, this issue may also because your client didn't have CA certificate of your domain. Please make sure that your client has CA certificate.
    Besides, the error "The client could not be authenticated because the Extensible Authentication Protocol (EAP) Type cannot be processed by the server" may be due to that the default maximum transmission unit that NPS uses for EAP payloads is 1500
    bytes. You can lower the maximum size that NPS uses for EAP payloads by adjusting the Framed-MTU attribute in a network policy to a value no greater than 1344:
    Configure the EAP Payload Size
    Best regards,
    Susie

  • A certificate could not be found that can be used with this Extensible Authentication Protocol. (Error 798)

    Hi,
    I posted this on Azure forim with no luck maybe here is a better choise.
    When trying to connect a windows 8\8.1 client with a vpn connection for azure virtual network we get the fallowing error.
    "A certificate could not be found that can be used with this Extensible Authentication Protocol. (Error 798)"\
    I'm fallowing this msdn article about point to site vpn on azure. according to it the certificat is good for both win 7 and win 8.
    http://msdn.microsoft.com/en-us/library/azure/dn133792.aspx
    this is the commanf to build the client certificat:
    makecert.exe -n "CN=ClientCertificateName" -pe -sky exchange -m 96 -ss My -in "RootCertificateName" -is my -a sha1
    When runing the installtion of the certificat on the client the defult crtificate store is "Automatic", It does not metter if I leave it on Automatic or choose any of the other options (personal, trusted issuers ...) I always get the same error.
    Thanks

    Hi,
    Apologize to say that I am not familar with Azure and lack of the environment to investigate the issue here.
    Besides, please take a look at the below threads to see if it could help:
    Point-to-Site on Windows 8 Client
    connection Error 798
    Best regards
    Michael Shao
    TechNet Community Support

  • When I try to go on iMessage and sign in it says iMessage Activation an error occurred during activation try again. This is the same for FaceTime please help :(

    ppls help me

    Turn off iMessage and FaceTime and restart
    Go to Settings > Messages and turn off iMessage.
    Go to Settings > FaceTime and turn off FaceTime.
    Restart your device.
    Turn iMessage and FaceTime back on.
    Still not activated after an hour?
    It might take a few minutes to activate iMessage and FaceTime. If you've waited more than an hour, try these steps:
    Make sure that your device has the latest version of iOS.
    If you're using an iPhone, contact your carrier to make sure that you can receive SMS messages.
    Contact Apple Support.

  • Error -1073807253 occurred at VISA Read in transient SR830.vi VISA: (Hex 0xBFFF006B) A framing error occurred during transfer.

    Hi,
    I am have written a program with labview to make transient c-v measurement using a stanford research SR830 lockin amplifier. The program seems to be runing fine, but sometimes it is givvibg an error:
    Error -1073807253 occurred at VISA Read in transient SR830.vi
    Possible reason(s):
    VISA:  (Hex 0xBFFF006B) A framing error occurred during transfer.
    Error -1073807253 occurred at VISA Read in transient SR830.vi
    Possible reason(s):
    VISA:  (Hex 0xBFFF006B) A framing error occurred during transfer.
    but if I press ok, the program again starts running. What might be the poblem? BTW I googled a bit and I see that in the labview topic "RS-232 Framing Error with HP 34401A Mulitmeter" by pkennedy32 this is what is said about framing error:
    ""Framing Error" in an RS-232 context means a very specific thing - when the receiver was expecting a stop bit, the line was not in SPACE condition. This can be the result of:
    1... Baud rate mismatch (although other problems would likely crop up first).
    2... Data Length problem, If I send 8 data bits and you expect 7, the stop bit is in the wrong place.
    3... Parity setting mismatch - If I send 7 data bits + parity and you expect 7 data bits and no parity, the stop bit is in the wrong place.
    4... Mismatch in # Stop bits - If I send you 7 Data bits + parity + one stop bit, and you expect 7 data bits + parity + TWO stop bits, the second one might not be correct, although most devices do not complain about this.
    But, I must say that this is the same com port setting that I use to measure c-v hysterysis, but I never gt this error there.
    I attach the program herewith for your kind perusal. Please help me resolve this issue.
    Thanks in advance.
    Solved!
    Go to Solution.
    Attachments:
    transient SR830.vi ‏94 KB
    csac.vi ‏8 KB
    sr830 initialize1.vi ‏15 KB

    @Dennis Knutson  you are right I checked the read indicator in backslash mode, and instead of a \n it is sending \r. So I changed the \n in my write strings to \r. But, if I keep the CLOSE VISA outside my loop instead of inside as you suggested, the termination character appears to come in the middle of the read string instead at the end. And since the read terminates at the \r so it is displaying some junk value before the \r, but if I put the CLOSE VISA outside the loop and play along with the bytes at the read buffer, I see the whole read string with the \r  at the end of the string. But, whenever the values are in exponential form (when close to zero) like 6.938839 e-5, I always get a time out error whatever be the timeout that I put at the VISA initialize. And subsequently, if I stop the program and run it again the machine program hangs and I donot get any reading. Then after I close it again and start, sometimes it hangs for some more or starts working. If I put an arbitrarily large byte count at the READ VISA, then I always get the time out before the operation completed error.
    @ Ravens Fan I have removed the CSAC VI altogether and taking the CH! And CH” reading separately, instead as one string. So, no more issues with that.
    I use the control at the delay so that I can choose how much delay I want to set, and I use the math operation because I am using adding up the delay time to keep track of the time elapsed. Because in the end I have t plot a time vs. CH! And CH” readings.
    I am not sure but probably I am making some silly errors. Please help me out. 
    Attachments:
    transient SR830-2.vi ‏103 KB
    sr830 initialize1.vi ‏15 KB

  • Errors occurred during post-handling PRGN_AFTER_IMP_ACTGROUP_ACGR for ACGR

    Hi,
    I have to import composite role from development to QAS system.I have generated profile for each role in developemnt & create transport of composite role & moved it in QAS.But in QAS it finished with Return code 8 & I found profiles are not moved in QAS for all single roles.
    Error is as follows.
    Errors occurred during post-handling PRGN_AFTER_IMP_ACTGROUP_ACGR for ACGR L
    The errors affect the following components:
       BC-SEC-USR-PFC (Authorization and Role Management)
    Please advice if anybody faced such kind of issue.
    Regards
    Santosh

    Rephrased a'la Julius:
    > To avoid the problems during the subsequent import into a target client, the AGR_NUM_2 table can be maintained as customizing for the clients (plural) in the source development system where the roles are maintained. If more than one client is used for role development, a number range gap of 50000 between the clients should be sufficient to prevent profile name collisions (otherwise you have much bigger problems anyway...).
    >
    > This is because the system ID (sy-sysid) is used as an attribute in the generated profile's name, but not the client (sy-mandt). > The value set in the AGR_NUM_2 tables determines the current number per client of the next sequential number to be used for profile generation. The customer can initialize this number to insert an additional attribute per client to achieve unique generated names within client specified ranges.
    Something like that
    Cheers,
    Julius

  • Error occurred during post handling RS_AFTER_IMPORT for UPDR L

    Hi friends,
    I need your help for 2 issues related to transport
    I am getting error while transporting the request from BW DEV to BW QAS..Please help me regarding this issue..
    1.)Error occurred during post handling RS_AFTER_IMPORT for UPDR L
           The errors affect the following components:
          BW-WHM (Warehouse Management)
    2.)Start of the after-import method RS_UPDR_AFTER_IMPORT for object type(s) UPDR (Activation Mode)
           Error when activating update rule
           IC=0CRM_PROD IS=0PR_IL_PROREF_ATTR error when checking update rules.
    Friends these are the two issues im facing while doing the transports._i have checked the update rules in the BW DEV it is working fine._please give some solutions to overcome this issues.
    Thanks
    Gnana Baskar

    Hi Gnana,
    Since u r telling tht the update rules are working fine in the Dev system, request u to perform some checks:
    1. The Update rule needs to be in active version.
    2. The InfoObjects used in the target InfoProvider should be present in the QA system/attached to the request in which u r transporting the changed Update Rule.
    3. Manually add objects, if needed all the Before/After objects in the new request and reactivate the Update rule, if it asks for a request give this new request number.
    4. Compare the data model in Dev and QA system and try finding the disconnect between them.
    Hope this helps.
    Regards,
    Kunal Gandhi

  • An error occurred while creating a Page Server subprocess.

    I am using XI R2 SP5 on solaris.
    When we try to view any report on demand or schedule any report that has a parameter, the following error comes back:
    An error occurred while creating a Page Server subprocess.
    I have tried restarting the services. I have tried creating a new page server. It behaves the same way. In other online forms, I've seen with this error message, people have talked about fixing it by installing SP2 or by uninstalling and reinstalling everything. We're at SP5, so we should have anything that was fixed at SP2. An uninstall and then reinstall would be a nightmare given the amount of use on this system.
    Can anyone recommend anything at all? I'm about to have our unix admins reboot the server, but that is really nothing more than a stab in the dark. I saw someone else in an online posting claim that a reboot fixed the problem, but I've only seen that once.

    checked this SAP Note?
    1204013 - Error: "The Page Server is unable to create a child process" when viewing a Crystal report in InfoView on Solaris
    Symptom
    When trying to view a Crystal report in BusinessObjects XI Release 2 InfoView on Solaris, the following error message appears:
    "The Page Server is unable to create a child process"
    In the syslogs, you see the following error messages:
    "An error occurred while creating a Page Server subprocess."
    "The function PEOpenEngineEx failed. Reason: Report engine not opened."
    "Internal error for dll procreport."
    "Unable to load dll procreport."
    "Internal Job Server error."
    Cause
    The following file in the MainWin registry has become corrupt:
    bobje/enterprise115/solaris_sparc/crpe/mw/registry/core_data/servername/.mw/hklm_sunos.bin
    This has become corrupt due to the web application server running under a different account than the BusinessObjects Enterprise applications.
    Resolution
    Restore the hklm_sunos.bin file using a backup of that file. The backup file must be from before the corruption occurred. Also ensure that your web application server and BusinessObjects Applications are running under the same user account.

  • NPS: Event 6274 - Network Policy Server discarded the request for a user

    Intermittently I will get desktop (wired) and laptop (wireless) computers experiencing issues with NPS (they drop off the network).
    Some computers are affected more than others, although they are identical hardware and based on a standard image.
    In the event log of the NPS servers I can see the following messages:
    Log Name:      Security
    Source:        Microsoft-Windows-Security-Auditing
    Date:          2/05/2014 8:47:58 a.m.
    Event ID:      6274
    Task Category: Network Policy Server
    Level:         Information
    Keywords:      Audit Failure
    User:          N/A
    Computer:      NT147.domain.local
    Description:
    Network Policy Server discarded the request for a user.Contact the Network Policy Server administrator for more information.User:
     Security ID:   NULL SID
     Account Name:   host/DPC0387.domain.local
     Account Domain:   DOMAIN
     Fully Qualified Account Name: DOMAIN\DPC0387$Client Machine:
     Security ID:   NULL SID
     Account Name:   -
     Fully Qualified Account Name: -
     OS-Version:   -
     Called Station Identifier:  3c-xx-xx-xx-xx-xx
     Calling Station Identifier:  00-xx-xx-xx-xx-xxNAS:
     NAS IPv4 Address:  10.nnn.nnn.nnn
     NAS IPv6 Address:  -
     NAS Identifier:   ND246
     NAS Port-Type:   Ethernet
     NAS Port:   71RADIUS Client:
     Client Friendly Name:  Network Device Management Subnet
     Client IP Address:   10.nnn.nnn.nnnAuthentication Details:
     Connection Request Policy Name: NAP 802.1X (Wired)
     Network Policy Name:  -
     Authentication Provider:  Windows
     Authentication Server:  NT147.domain.local
     Authentication Type:  -
     EAP Type:   -
     Account Session Identifier:  384F322E317838316564303034313030306230666632
     Reason Code:   1
     Reason:    An internal error occurred. Check the system event log for additional information.
    How do I debug when an internal error occurs but there is nothing in the system event log? Where else can I look?
    Here's the packet trace that matches the event log entry above:
    No.     Time        Source                Destination           Protocol Length Time from request Info
          1 0.000000    JuniperN_xx:xx:xx     Universa_xx:xx:xx     EAP      60                       Request, Identity
          2 2.470423    Universa_xx:xx:xx     Nearest               EAPOL    60                       Start
          3 2.472870    JuniperN_xx:xx:xx     Universa_xx:xx:xx     EAP      60                       Request, Identity
          4 2.539416    Universa_xx:xx:xx     Nearest               EAP      60                       Response, Identity
          5 2.544206    Universa_xx:xx:xx     Nearest               EAPOL    60                       Start
          6 2.548804    JuniperN_xx:xx:xx     Universa_xx:xx:xx     EAP      60                       Request, Identity
          7 2.550050    Universa_xx:xx:xx     Nearest               EAP      60                       Response, Identity
          8 2.552597    10.switch             10.NPS_Server         RADIUS   254                      Access-Request(1) (id=249, l=208)
          9 2.556043    10.NPS_Server         10.switch             RADIUS   136    0.003446000       Access-Challenge(11) (id=249, l=90)
         10 2.565876    JuniperN_xx:xx:xx     Universa_xx:xx:xx     EAP      60                       Request, Protected EAP (EAP-PEAP)
         11 2.569472    10.switch             10.NPS_Server         RADIUS   254                      Access-Request(1) (id=250, l=208)
         12 2.572566    10.NPS_Server         10.switch             RADIUS   136    0.003094000       Access-Challenge(11) (id=250, l=90)
         13 2.580254    Universa_xx:xx:xx     Nearest               TLSv1    123                      Client Hello
         14 2.586544    10.switch             10.NPS_Server         RADIUS   361                      Access-Request(1) (id=251, l=315)
         15 4.564841    Universa_xx:xx:xx     Nearest               EAPOL    60                       Start
         16 4.568530    JuniperN_xx:xx:xx     Universa_xx:xx:xx     EAP      60                       Request, Identity
         17 4.569876    Universa_xx:xx:xx     Nearest               EAP      60                       Response, Identity
         18 4.582263    10.switch             10.NPS_Server         RADIUS   254                      Access-Request(1) (id=252, l=208)
         19 4.586006    10.NPS_Server         10.switch             RADIUS   136    0.003743000       Access-Challenge(11) (id=252, l=90)
         20 4.591896    JuniperN_xx:xx:xx     Universa_xx:xx:xx     EAP      60                       Request, Protected EAP (EAP-PEAP)
         21 4.592692    Universa_xx:xx:xx     Nearest               TLSv1    123                      Client Hello
         22 4.599634    10.switch             10.NPS_Server         RADIUS   361                      Access-Request(1) (id=253, l=315)
         23 4.600887    10.NPS_Server         10.switch             IPv4     1518                     Fragmented IP protocol (proto=UDP 17, off=0, ID=07db)
         24 4.609920    JuniperN_xx:xx:xx     Universa_xx:xx:xx     TLSv1    1514                     Server Hello, Certificate, Certificate Request, Server Hello Done
         25 4.610516    Universa_xx:xx:xx     Nearest               EAP      60                       Response, Protected EAP (EAP-PEAP)
         26 4.617407    10.switch             10.NPS_Server         RADIUS   262                      Access-Request(1) (id=254, l=216)
         27 4.618352    10.NPS_Server         10.switch             RADIUS   288    0.000945000       Access-Challenge(11) (id=254, l=242)
         28 4.623650    JuniperN_xx:xx:xx     Universa_xx:xx:xx     TLSv1    176                      Server Hello, Certificate, Certificate Request, Server Hello Done
         29 4.643316    Universa_xx:xx:xx     Nearest               TLSv1    361                      Certificate, Client Key Exchange, Change Cipher Spec, Encrypted Handshake Message
         30 4.649607    10.switch             10.NPS_Server         RADIUS   601                      Access-Request(1) (id=255, l=555)
         31 4.656950    10.NPS_Server         10.switch             RADIUS   199    0.007343000       Access-Challenge(11) (id=255, l=153)
         32 4.662734    JuniperN_xx:xx:xx     Universa_xx:xx:xx     TLSv1    87                       Change Cipher Spec, Encrypted Handshake Message
         33 4.681106    Universa_xx:xx:xx     Nearest               EAP      60                       Response, Protected EAP (EAP-PEAP)
         34 4.788536    10.switch             10.NPS_Server         RADIUS   262                      Access-Request(1) (id=2, l=216)
         35 4.789735    10.NPS_Server         10.switch             RADIUS   173    0.001199000       Access-Challenge(11) (id=2, l=127)
         36 4.795723    JuniperN_xx:xx:xx     Universa_xx:xx:xx     TLSv1    61                       Application Data
         37 4.796372    Universa_xx:xx:xx     Nearest               TLSv1    93                       Application Data
         38 4.802368    10.switch             10.NPS_Server         RADIUS   331                      Access-Request(1) (id=3, l=285)
         39 4.803363    10.NPS_Server         10.switch             RADIUS   189    0.000995000       Access-Challenge(11) (id=3, l=143)
         40 4.808905    JuniperN_xx:xx:xx     Universa_xx:xx:xx     TLSv1    77                       Application Data
         41 4.809501    Universa_xx:xx:xx     Nearest               TLSv1    77                       Application Data
         42 4.817342    10.switch             10.NPS_Server         RADIUS   315                      Access-Request(1) (id=4, l=269)
         43 4.822986    10.NPS_Server         10.switch             RADIUS   189    0.005644000       Access-Challenge(11) (id=4, l=143)
         44 4.828973    JuniperN_xx:xx:xx     Universa_xx:xx:xx     TLSv1    77                       Application Data
         45 4.833318    Universa_xx:xx:xx     Nearest               TLSv1    829                      Application Data
         46 4.840610    10.switch             10.NPS_Server         RADIUS   1073                     Access-Request(1) (id=5, l=1027)
         47 4.845946    10.NPS_Server         10.switch             RADIUS   189    0.005336000       Access-Challenge(11) (id=5, l=143)
         48 4.850938    JuniperN_xx:xx:xx     Universa_xx:xx:xx     TLSv1    77                       Application Data
         49 4.907924    Universa_xx:xx:xx     Nearest               TLSv1    141                      Application Data
         50 4.913390    10.switch             10.NPS_Server         RADIUS   379                      Access-Request(1) (id=6, l=333)
         51 4.917535    10.NPS_Server         10.switch             RADIUS   221    0.004145000       Access-Challenge(11) (id=6, l=175)
         52 4.922877    JuniperN_xx:xx:xx     Universa_xx:xx:xx     TLSv1    109                      Application Data
         53 4.923472    Universa_xx:xx:xx     Nearest               TLSv1    61                       Application Data
         54 4.930319    10.switch             10.NPS_Server         RADIUS   299                      Access-Request(1) (id=7, l=253)
         55 4.937348    10.NPS_Server         10.switch             RADIUS   381    0.007029000       Access-Challenge(11) (id=7, l=335)
         56 4.942543    JuniperN_xx:xx:xx     Universa_xx:xx:xx     TLSv1    269                      Application Data
         57 4.944791    Universa_xx:xx:xx     Nearest               TLSv1    125                      Application Data
         58 4.951408    10.switch             10.NPS_Server         RADIUS   363                      Access-Request(1) (id=8, l=317)
         59 4.954022    10.NPS_Server         10.switch             RADIUS   355    0.002614000       Access-Accept(2) (id=8, l=309)
         60 4.981482    JuniperN_xx:xx:xx     Universa_xx:xx:xx     EAP      60                       Success
         61 32.590347   10.switch             10.NPS_Server         RADIUS   361                      Access-Request(1) (id=251, l=315)
         62 62.592420   10.switch             10.NPS_Server         RADIUS   361                      Access-Request(1) (id=251, l=315)
         63 92.595043   10.switch             10.NPS_Backup_Server  RADIUS   361                      Access-Request(1) (id=9, l=315)
         64 122.597856  10.switch             10.NPS_Backup_Server  RADIUS   361                      Access-Request(1) (id=9, l=315)
         65 152.600618  10.switch             10.NPS_Backup_Server  RADIUS   361                      Access-Request(1) (id=9, l=315)

    A belated thanks for your reply.
    Our environment doesn't have NPS accounting configured so that was easy to rule out.
    The mid-day drop outs have stopped after I added "set protocols dot1x authenticator no-mac-table-binding" to our Juniper switches (which prevents mac address aging from clearing the active dot1x client session).
    I believe the above error message occurs because the RADIUS session ID is rejected / ignored because of some quirks in the RADIUS standard.  At the start of a dot1x authentication request a RADIUS session ID is created.  For whatever reason the
    RADIUS/NAP server stops responding and the Juniper switch fails over to the backup RADIUS/NAP server configured.  The session ID is kept (per RADIUS standard) but the backup RADIUS/NAP server doesn't know about the session, so this event: "Network
    Policy Server discarded the request for a user." occurs.
    It would be nice to see a clearer error message "Invalid RADIUS session" or similar.
    There is a Microsoft guide on how to set up RADIUS/NAP servers in a highly available configuration - something to do with RADIUS proxy servers.
    It would be even nicer to see some kind of RADIUS session synchronisation between NAP servers... if it doesn't already exist?
    I am having the same exact issue you posted on here except I have Extreme Network switches. Some of my computers, various hardware, will randomly not authenticate during re-authentication. The switch says that it failed to contact the NPS server so then it
    switches to my backup server. The client has a random time on how long it waits to authenticate so sometimes I end up having the disable/re-enable the port they are connected to so that the session is started again. I see that you basically removed the option
    to force clients to re-authenticate Any downfall disabling that?. Any idea why the NPS server is no longer responding? Are you using Windows Server 2012?

  • 6274: Network Policy Server discarded the request for a user

    How to reproduce this event:
    6274: Network Policy Server discarded the request for a user

    Hello,
    according to the following just use an older RADIUS client version:
    Warning: NPS discarded the request for a user
    This monitor returns the number of events when the Network Policy Server discarded the request for a user.
    Type of event: Warning. Event ID: 6274.
    This condition occurs when the NPS discards accounting requests because the structure of the accounting request message that was sent by a RADIUS client does not comply with the RADIUS protocol. You should reconfigure, upgrade, or replace the RADIUS
    client.
    Best regards
    Meinolf Weber
    MVP, MCP, MCTS
    Microsoft MVP - Directory Services
    My Blog: http://msmvps.com/blogs/mweber/
    Disclaimer: This posting is provided AS IS with no warranties or guarantees and confers no rights.

  • System.Exception: An error occurred during the Microsoft VSTO Tools 4.0 install (exit code was -2146762485).

    I have been trying to install a piece of software on 2 Windows 7 PCS called Rightfax...during installing I get the error below;
           System.Exception: An error occurred during the Microsoft VSTO Tools 4.0 install (exit code was -2146762485).
    It then gives me an error log of ;
    2015-04-23 14:43:03Z: Error: Unexpected problem occurred in task worker
           System.Exception: An error occurred during the Microsoft VSTO Tools 4.0 install (exit code was -2146762485).
              at CommonInstall.Tasks.InstallTask.LaunchInstall(String friendlyName, String exe, String args, Int32[] exitCodesToIgnore)
              at CommonInstall.Tasks.InstallVSTO.OnRun(ITaskFeedback feedback)
              at TaskWizard.Task.Run(ITaskFeedback feedback, Boolean recurse)
              at TaskWizard.TaskWorker.RunTasks()
              at TaskWizard.TaskWorker.OnDoWork(DoWorkEventArgs e)
    2015-04-23 14:43:03Z: Error: Problem in sequence or one of its pages
           System.Exception: An error occurred during the Microsoft VSTO Tools 4.0 install (exit code was -2146762485).
              at CommonInstall.Tasks.InstallTask.LaunchInstall(String friendlyName, String exe, String args, Int32[] exitCodesToIgnore)
              at CommonInstall.Tasks.InstallVSTO.OnRun(ITaskFeedback feedback)
              at TaskWizard.Task.Run(ITaskFeedback feedback, Boolean recurse)
              at TaskWizard.TaskWorker.RunTasks()
              at TaskWizard.TaskWorker.OnDoWork(DoWorkEventArgs e)
              at CommonInstall.PreparationWorker.OnDoWork(DoWorkEventArgs e)
              at System.ComponentModel.BackgroundWorker.WorkerThreadStart(Object argument)
    2015-04-23 14:43:03Z: Error: Problem in sequence or one of its pages
           System.Exception: An error occurred during the Microsoft VSTO Tools 4.0 install (exit code was -2146762485).
              at CommonInstall.Tasks.InstallTask.LaunchInstall(String friendlyName, String exe, String args, Int32[] exitCodesToIgnore)
              at CommonInstall.Tasks.InstallVSTO.OnRun(ITaskFeedback feedback)
              at TaskWizard.Task.Run(ITaskFeedback feedback, Boolean recurse)
              at TaskWizard.TaskWorker.RunTasks()
              at TaskWizard.TaskWorker.OnDoWork(DoWorkEventArgs e)
              at CommonInstall.PreparationWorker.OnDoWork(DoWorkEventArgs e)
              at System.ComponentModel.BackgroundWorker.WorkerThreadStart(Object argument)
    2015-04-23 14:43:03Z: Info: Page changed from 'WizardWorkerPage' to 'ResultPage' driven by result 'Next' and exception 'none'
    2015-04-23 14:44:06Z: Info: Page changed from 'ResultPage' to 'none' driven by result 'Next' and exception 'none'
    2015-04-23 14:44:06Z: Info: Work has not been completed; install state will not be saved.
    2015-04-23 14:44:06Z: Info: Reboot status = NotRequired
    2015-04-23 14:44:06Z: Info: Exitcode = 0
    2015-04-23 14:44:06Z: Info: Logging ended.
    I have installed this software succesfully on other machines previously.....

    Hi RyanWelsh78,
    This forum is discussing about Visual Stuido Tools for Office developing, your issue is related with the installing Rightfax add-in which is a third party product. As the reply from Eugene, you could contact Rightfax add-in developers for help.
    Thanks for your understanding.
    Best Regards,
    Edward
    We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
    Click
    HERE to participate the survey.

  • ERROR: An error occurred during the installation of assembly component / ERROR: Third party payload installer Adobe_Lightroom_x64.msi failed with exit code: 1603

    During the Installation of LR I get an error message. Initially I didn't have enough space for the installation on the start partition drive. However, now, it should be sufficient and I re-booted the computer a couple of time, hence I would assume that the temporary installation files have been deleted.
    Now, nevertheless each time I try to re-install the software I get the following messages:
    ERROR: An error occurred during the installation of assembly component {6435B7C0-E0C8-3EA2-91AE-7640034EAFCE}. HRESULT: 0x80070002.
    ERROR: Install MSI payload failed with error: 1603 - Schwerwiegender Fehler bei der Installation.
    MSI Error message: An error occurred during the installation of assembly component {6435B7C0-E0C8-3EA2-91AE-7640034EAFCE}. HRESULT: 0x80070002.
    ERROR: Third party payload installer Adobe_Lightroom_x64.msi failed with exit code: 1603
    Since PS was installed without problems I would refrain from deinstalling the Creative Cloud and start over again.
    Any hints?
    Thx

    Claasd5335054 you will want to review the MSI log files to determine what error message is preventing the installation from completing.
    ERROR: An error occurred during the installation of assembly component {6435B7C0-E0C8-3EA2-91AE-7640034EAFCE}. HRESULT: 0x80070002.
    ERROR: Install MSI payload failed with error: 1603 - Schwerwiegender Fehler bei der Installation.
    MSI Error message: An error occurred during the installation of assembly component {6435B7C0-E0C8-3EA2-91AE-7640034EAFCE}. HRESULT: 0x80070002.
    ERROR: Third party payload installer Adobe_Lightroom_x64.msi failed with exit code: 1603
    This is the only error information contained within Adobe Lightroom 5's installation log.  The MSI log files contain the additional error messages.

Maybe you are looking for