When I want to make a phonecall with my iphone5, I hear absolutely nothing....no ringing and no talking when connection established. When I make the same call but now on speaker, no problem or what so ever, can anyone help me ?
When I want to make a phonecall with my iphone5, I hear absolutely nothing....no ringing and no talking when connection established. When I make the same call but now on speaker, no problem or what so ever, can anyone help me ?
Hello there, RobenCaatje.
The following Knowledge Base article is specific for the issue you're describing:
iPhone: Can't hear through the receiver or speakers
http://support.apple.com/kb/TS1630
Specifically:
Resolution
Verify that there is nothing plugged in to the headset jack, including headsets, headphones, or adapters.
Make sure the Ring/Silent switch is not switched to silent.
While on the Home screen, adjust the volume buttons. If you see the icon below, indicating that headphones are attached, there may be debris or an object lodged in the headset jack:
Check the headset jack. If there is an object lodged in the headset jack that is not easily removed, have the iPhone serviced to remove object.
For Original iPhone: If there is light debris, such as lint, in the headset jack, try connecting a pair of headphones to the headset jack and then remove the headphones. Repeat this several times to remove the debris.
If you have installed a protective film on the display, either ensure that the receiver is not covered or remove the film completely.
Check the receiver mesh (which is on the top front of the device, above the display). If it appears blocked, use a clean, small, dry, soft-bristled brush to carefully and gently brush away any debris.
If you have paired with a Bluetooth headset that is nearby, either use the headset or turn Bluetooth off (chooseSettings > General > Bluetooth).
Restart the iPhone.
If restarting the iPhone doesn't resolve the issue, try restoring the device.
If the issue persists, go to the Service Answer Center - iPhone for information on service.
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro D.
Similar Messages
-
Hello, I upgraded my laptop from Snow Leopard to lion, unfortunately I have a 2 music programs that no longer work. one is called the Music PadPro, which is now gone bankrupt, can anyone help?. I was talking to the Apple Store earlier and they said if I upgrade to the mountain lion it may help but I'm not so sure,
kind regards
NigelThere's no reason that upgrading from Lion to Mountain Lion would make this application work. I've looked up Music PadPro. I don't know much about it, but it looks pretty old. Here are the requirements:
Macintosh G4 or higher processor running Mac OS X Version 10.2.6 (minimum),
Mac OS X Version 10.3.2 (recommended), or Mac OS X Version 10.4.2.
Looking at that, I would guess that the application would require a PowerPC processor. After the release of the Intel machines back in 2006, Apple included something called Rosetta within OS X. This allowed programs developed for the older architecture (PowerPC) to run on the newer Intel machines. The reason for this was to give developers some time to upgrade their applications to run natively on Intel processors. It was only with the introduction of Lion that Apple pulled Rosetta from their OS. They had basically given developers about five years to upgrade their applications. Unfortunately, in your case, the developer went belly up. You can always install an older version of the OS on either a separate partition or an external drive and you can run your program from there. -
i just upgraded my phone from an 3g to an iphone 4. had att switch the sims so i could use the iphone 4. now i cannot find my playlists? can anyone help out? thanx
What do you mean?
The playlist would only be on your iphone if you put it there.
The SIM cars has NOTHING to do with the content on the iphone. -
Okay I wanted to upload a photo to instagram but i could'nt because it said that I had to go to privacy settings go to photos and turn on the instagram app but there wasnt any app to switch to on amda i dont know what to do can anyone help me?
I also have the ios7 and before i upgraded it it worked fine
-
I just got an Ipad and I really dont know much about them its a 32gb 4g wi-fi, I use at&t as my server(dsl) and that works fine but I need to download my mcafee which comes with my at&t for free but it wont let me download it says I need more than 6.1.0and I dont know what to do can anyone help, I know someone that has 1 just like mine but she doesnt use a antivirus and doesnt have any trouble but,,, I have a laptop and a desktop and I use mcafee on both,, so any suggestions, I just down know what to do,,, can anyone give me input on what to do, and I also what to know is there anyway I can use my portable device that I got thru at&t that I can buy minutes on, is there an adapter for this ipad that I can use this on,, help I need all I can get,, thanks chrystie
You can not install it.
Only apps from the official Apple App Store can be installed. -
I purchased a 3TB Airport Time Capsule to use with my Mac running latest Maverics. After 8 hours been able to configure the box using Ethernet connection but now I want to move my current backups from my small driveand it wants authentication but no box is available to provide my administrator name can anyone help ?
I overcame the permissions by allowing both paths to have read and write access to anyone but that didnt solve it until I copied it into the DATA directory which I created on the Airport Time Capsule.
I had already discovered the TIME MACHINE How to transfer backups but I am struggling still with the item and cannot currently get it to work. My setup seems to have created a wireless link to my router which is what I wanted and in that set up there are three options. I have simply gone for the extension of my network. I ignored the other option there which I cannot remember something like DNS? That may be the problem becasuse when I remove the Ethernet connector it just doesnt go anywhere.
I have also found I cannot update my TIME MACHINE software (currently 1.3) as although Apple tell me I should be able to set backups hourly daily or weekly I have only ever been able to run it hourly when i would prefer longer intervals so thought an update might be necssary.
Also tried to get an update for my Airport Utility (Currently 6.3.2 but cannot find one even though I have read there might be one available and again this might be the problem.
Have reset the Time Capsule now about a dozen times.
Following the instructions and trying to copy my existing backup it suggests you need to copy it to the root directory but that is when I get some sort of security issue and I found I could only get it to accept if I dragged my .backupdb to the DATA directory on the Time Capsule. I dont even know if I do this it will work when I come to use it.
I therefore found your reply of no more help than i had discovered but I hope you return to read this note because I really do need some help.
I am intending starting again in the next couple of days and fully documenting what I do and what I see and then as I suspect it will be no different and I will then seek an appointment at the Apple Store in Trafford Centre and if that proves unsuccessful then I still have time to return and become a dissatisfied customer with Apple for the first time in a long experience with Apple. I have noticed frightening notes on the conversations which point to problems of Mavericks working with Airport Time Machine!! So in the end it might not be me doing anything wrong. Unfortunately you do feel left out in the dark sometimes that is why I hope you can respond with a solution? -
My wifi is not working. It has no indication. I am living in Indonesia but I bought my iphone from apple online store. Can anyone help me how to fix my problem?
The No Service means there is a problem with cellular service. You mention wifi in your title. Which is it you are having trouble with? What happens when you switch on and off as you state in your post? Are you saying that wifi does not connect while at home either?
-
I am having problems accessing my airport utilities, the area which allows me to alter settings is all greyed out. Can anyone help?
Using the same Ethernet cable that is used to connect the modem to the AirPort Extreme, disconnect the Ethernet cable from the AirPort Extreme and connect it directly to your Mac as a test for 4-6 hours.
Be sure to power off the modem for 5-10 minutes when you do this, so that it will associate with the new device that it "sees".
Does the connection drop when you connect this way? If yes, then replace the Ethernet cable and run the test again for 4-6 hours.
If the connection still drops, you likely have a defective modem or a line problem on the cable service....despite what the cable company might say.
If the connection remains solid when you run the "test", then you know that the modem and Ethernet cable are working correctly.
If you have performed a factory default reset on the AirPort Extreme a few times, and connection still drops, then you should take the AirPort to an Apple Store....if you have one near you..... to let them take a look, or contact Apple Support directly.
http://www.apple.com/support/contact/ -
When I print a 4x6 color picture using an iMac with the latest operating system using a Canon MX892 printer, faint black lines appear every 3/16 of an inch. When I print the same picture using iPhoto there is no problem. Any suggestions?
What is the resolution of the picture that you are trying to print?
Go to Image>resize>image size, read the resolution in px/in, then report back, please.
Also, are you in a position to try printing with another printer in an attempt to narrow this down? -
I cannot connect to FaceTime, encountered "error processing registration, please try later" message on my Macbook Air, but I don't have this problem on my IMac. Can anyone help?
I have the same problem on my iMac. My facetime has been working, but now I'm getting the same error as You. I've been through the following:
The stuff that Linc Davis suggested, new profile on iMac, moved iMac into DMZ zone with no firewall rules, tested with other Apple-ID, checked hosts file, checked different timezone settings, tried to connect to 2 mobile APs (with diferent providors), changed DNS servers (ISP's DNS + Google DNS + Open DNS) - Nothing helped. Also talked to Apple Support, since i have Apple Care, but the seem to be a bit clueless also Well I've mailed them the results of my different tests, so lets see what they come up with - Unfortunately I'm sure it will be the same suggestion as all the major PC manufactures suggests, reinstall and test - RIGHT !!!!!!
If I get solution, I'll post it here.
Kind Regards
Kim -
Hey, I need to download the OS onto my iPhone 3GS, however, when I plug my phoneinto itunes it does not give me the option to do so, I am currently running 4.2.1. Can anyone help me?
irapidslammz wrote:
I can not sync it because when I plug it in it says that the apple mobile service has not been started.
Type " apple mobile device service" into the search bar at the top of this page by Support and read the resulting help article. -
When I try to update Adobe Flash Player I'm prompted to quit Safari and Dashboard Client. I quit Safari but I don' know how to quit Dashboard Client. Can anyone help with this challenge?
Carolyn,
Thank you. It worked
Angus. -
I just got a retro clock from brookstone and in setting it up it asked if I want to use current location which is incorrectly "Buffalo" but I do not know how to change it. Can anyone help me find where to change location?
As I understand it, Apple gets your location from the wi-fi router to which your iPod is connected. Location Services identifies the router and then checks for its location in Apple's database. If the router has been recently relocated or if there is a glitch in Apple's database, you will get an incorrect location. I don't think that there is anything you can do about it. You could send Apple a message about the error, but I doubt if they would do anything about it.
-
I have an iMac (Mid 2010) and am running 0sx 10.8.5 and the WiFi always loses connection during sleep mode. I have seen numerous different solutions none of which seem to work. Can anyone help?
Test after taking each of the following steps that you haven't already tried. Back up all data before making any changes.
1. Make sure the network is on the preferred list by following these instructions. It's important to read the article carefully, as it's the starting point for any further efforts to solve the problem. If you skip any of the steps, the problem may not be solved. Make sure the box marked
Remember networks this computer has joined
is checked.
2. Follow the instructions in this support article under the heading
Symptom: After restarting or waking from sleep, my computer might not connect to the Internet
3. Reset the PRAM.
4. Make a note of all your settings for Wi-Fi in the Network preference pane, then delete the connection from the connection list and recreate it with the same settings. You do this by clicking the plus-sign icon below the connection list, and selecting Wi-Fi as the interface in the sheet that opens. Select Join other network from the Network Name menu, then select your network. Enter the password when prompted and save it in the keychain.
5. From the Location menu at the top of the Network preference pane, select Edit Locations. A sheet will drop down. Click the plus-sign button to create a new location. Give it any name you want. In the new location, set up the Wi-Fi service with the same settings you used before. Click Apply and test.
6. Launch the Keychain Access application. Search for and delete all AirPort network password items that refer to the network. Make a note of the password first.
7. Repair permissions on the startup volume.
8. Turn off Bluetooth and test.
9. Reset the System Management Controller.
10. This step shouldn't be necessary, but has been advised by Apple Support in some cases, apparently as a workaround for a bug. Open the Energy Saver pane in System Preferences. If applicable, click the padlock icon in the lower left corner to unlock the settings. Enter your administrator login password when prompted.
Select the Power Adapter tab and uncheck the boxes marked
Wake for Wi-Fi network access
and
Enable Power Nap...
if present. Then, if the computer is a MacBook, select the Battery tab and uncheck
Enable Power Nap...
11. Reinstall OS X. -
I just bought a new Iphone and when I connected it to itunes and I downloaded the backup from my last device, now I can't pass this step and every time I connect it to itunes is the same thing. And I can't download any app because problems with my account regarding the credit card but the information is correct and it says it is not!!!
You'll have to contact iTunes store support regarding your credit card information problem: http://www.apple.com/emea/support/itunes/contact.html. I'm not clear on what you're saying about your backup. Are you saying that when you connect to iTunes it's asking you to restore from backup even though you already have?
Maybe you are looking for
-
I am unable to print from my ipod to HP5510 which is listed as one of Apple's Airprinters
I am unable to print from my ipod to HP5510 which is listed in Apple's list of recognised Airprinters
-
Everything that happens to my sister's phone is happening to mine?!?! How can I stop it?
This happened randomly. My sister was text messaging her friend when all of a sudden I got the texts. On the message screen it showed text messages that "I" (but really my sister) had sent. When I asked who it was and who they were trying to talk to
-
Hi, I have just installed "InstallAnywhere" and am using NetBeans IDE to develop my code. I created a very simple gui (just the frame) and tried to create an executable with InstallAnywhere but I got this error: Unable to locate the applications main
-
Hi everyone, Who have a good way to draw lines on SAP form? I created a Wizard form, and use Rectangle (Height=0) as the two lines between title and bottom button, but I met a problem, when show another form which cover the line, after close this for
-
Pictures in older text messages now have question marks
Seems after upgrading to 8.11, older text messages with pictures have had the pictures replaced by question marks. I have googled and tried resetting network settings and stuff like that to no avail. Current and new messages seem to be fine, seems to