WLC 2504 LAG is not working?
Hi All,
Yesterday i configured LAG on my New WLC using following configuration:
Enable LAG on controller > General
then reboot
On Neighbor Switch:
Interface range GigabitEthernet <Interfce ID>
Channel-group <id> mode on
no sh
Interface port-channel <id>
switchport trunk allowed vlan <id>
switchport mode trunk
no sh
i can see on switch trunk is established.
I also tag the LAG to my management vlan.
But still not working, can any one help me to find what going wrong.
I have HA device i configure same on that it worked. But not working on my primary
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 8.0.110.0
Bootloader Version............................... 1.0.20
Field Recovery Image Version..................... 7.6.101.1
Firmware Version................................. PIC 16.0
Build Type....................................... DATA + WPS
System Name......................................
System Location..................................
System Contact...................................
System ObjectID..................................
IP Address.......................................
IPv6 Address..................................... ::
Last Reset....................................... Software reset
System Up Time................................... 0 days 0 hrs 21 mins 0 secs
System Timezone Location.........................
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
--More-- or (q)uit
Configured Country...............................
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +28 C
External Temperature............................. +33 C
Fan Status....................................... 4300 rpm
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 1
Number of Active Clients......................... 0
Burned-in MAC Address............................
Maximum number of APs supported.................. 75
System Nas-Id....................................
WLC MIC Certificate Types........................ SHA1
Try to delete the config on switch and try this.
Switch config :
interface range <>
switchport trunk encapsulation dot1q
switchport mode trunk
switchport trunk allowed vlan X,Y,Z
Channel-group <> mode on
Still not working then check if WLC is reachable via ssh or telnet!
if you have access via ash or telnet then reboot WLC by using "reset system" command .
hope it helps.
Regards
Dont forget to rate helpful posts
Similar Messages
-
Hi there,
We're running AireOS 8.0 in a WLC 8500 series and we're getting problems trying to enable HA scenario. These are the scenarios we have tested:
management interface tagged + switchport trunk tagged + HA tagged + switchport trunk tagged = SSO not working
management interface tagged + switchport trunk tagged + HA tagged + switchport access = SSO not working
management interface untagged + switchport trunk native vlan + HA untagged + switchport access = SSO not working
No scenario is working and in cases 1 and 2 we are lossing the associated APs and we only recover them in case 3.
In parallel, after enabling tagged interface in management, the "show ip arp" of the switch shows the IP through the HA interface and the ping is lost outwards WLC and inwards.
Any suggestion?
Regards.Try to delete the config on switch and try this.
Switch config :
interface range <>
switchport trunk encapsulation dot1q
switchport mode trunk
switchport trunk allowed vlan X,Y,Z
Channel-group <> mode on
Still not working then check if WLC is reachable via ssh or telnet!
if you have access via ash or telnet then reboot WLC by using "reset system" command .
hope it helps.
Regards
Dont forget to rate helpful posts -
Hello All,
I am having difficulty connecting via gui to my 2504 WLC controller, with code 7.4 VIA a Lag link. i have configured a tagged vlan (vlan 40) on the WLC ap-management port.
I have configured a port-channel on a C2960s
interface Port-channel2
switchport trunk allowed vlan 1,40,45,50,55,60
switchport mode trunk
I have configured the interfaces on the C2960S
interface range GigabitEthernet1/0/1 - 4
description BH-C2960SPSL24-01 connection to BH-C2504WLC-01
switchport trunk allowed vlan 1,40,45,50,55,60
switchport mode trunk
channel-group 2 mode active
I can ping the interface, but cannot bring up a gui.=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2013.01.17 22:27:37 =~=~=~=~=~=~=~=~=~=~=~=
show run
Building configuration...
Current configuration : 10532 bytes
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
boot-start-marker
boot-end-marker
no aaa new-model
switch 1 provision ws-c2960s-24ps-l
crypto pki trustpoint TP-self-signed-131252096
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-131252096
revocation-check none
rsakeypair TP-self-signed-131252096
crypto pki certificate chain TP-self-signed-131252096
certificate self-signed 01
3082023D 308201A6 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
30312E30 2C060355 04031325 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 31333132 35323039 36301E17 0D393330 33303130 30303830
355A170D 32303031 30313030 30303030 5A303031 2E302C06 03550403 1325494F
532D5365 6C662D53 69676E65 642D4365 72746966 69636174 652D3133 31323532
30393630 819F300D 06092A86 4886F70D 01010105 0003818D 00308189 02818100
D1D20BAE AE0D9EF4 049AF361 1FFAC404 33C7940F 0EC84FA3 52470085 11BE1B6F
EF7795D5 D81F0AD5 25D3668A 7004C157 BC4C4AE6 84A3302A CE774AAF E388A3BE
1249476C 396F042A 90DA38B8 5C413D4E 1C6A9405 80A12F74 50F6571E DC11306E
6AFFB6DF FB6E9292 96EE61A6 9EF87310 E4722DB3 3B10368D C737BAE4 93F3B759
02030100 01A36730 65300F06 03551D13 0101FF04 05300301 01FF3012 0603551D
11040B30 09820753 77697463 682E301F 0603551D 23041830 168014CE 95CAC648
8F3F96AE B382A38E 4AC7B6BF 9DEB9F30 1D060355 1D0E0416 0414CE95 CAC6488F
3F96AEB3 82A38E4A C7B6BF9D EB9F300D 06092A86 4886F70D 01010405 00038181
0063BCAE 64F7D969 244A07C3 B0D70FEF 00E78CF7 4EF017BE 72745FED 090AF5DA
7420B4BD EAB89849 C7241FAE A8496714 5BF6331F A6936762 A861756E A55A43D8
9366AAB5 C55DECEE F84AFC63 964834C0 E917FCF5 DA5B9043 FD0365B6 03351CA8
7C4EAB92 831BA642 DD210D4B 0C21E6A8 F0BDA231 3AF9652C D376DAC2 1E17ABFC DB
quit
spanning-tree mode pvst
spanning-tree extend system-id
auto qos srnd4
port-channel load-balance src-dst-ip
vlan internal allocation policy ascending
interface Port-channel1
switchport trunk allowed vlan 1,40,45,50,55,60
switchport mode trunk
interface Port-channel2
switchport trunk native vlan 99
switchport trunk allowed vlan 1,40,45,50,55,60
switchport mode trunk
interface FastEthernet0
no ip address
shutdown
interface GigabitEthernet1/0/1
switchport trunk native vlan 99
switchport trunk allowed vlan 1,40,45,50,55,60
switchport mode trunk
channel-group 2 mode on
interface GigabitEthernet1/0/2
switchport trunk native vlan 99
switchport trunk allowed vlan 1,40,45,50,55,60
switchport mode trunk
channel-group 2 mode on
interface GigabitEthernet1/0/3
switchport trunk native vlan 99
switchport trunk allowed vlan 1,40,45,50,55,60
switchport mode trunk
channel-group 2 mode on
interface GigabitEthernet1/0/4
switchport trunk native vlan 99
switchport trunk allowed vlan 1,40,45,50,55,60
switchport mode trunk
channel-group 2 mode on
interface GigabitEthernet1/0/21
description BH-C2960S-01 GI 1/0/21 trunk connection to Watchguard Firebox
switchport trunk native vlan 99
switchport mode trunk
interface GigabitEthernet1/0/22
description Switch connection to AP
interface GigabitEthernet1/0/23
description BH-2960S-01 GI 0/22-24 trunk connection to BH-HPJ9022A-01 gi 47-48
switchport trunk allowed vlan 1,40,45,50,55,60
switchport mode trunk
channel-group 1 mode active
interface GigabitEthernet1/0/24
description BH-2960S-01 GI 0/22-24 trunk connection to BH-HPJ9022A-01 gi 47-48
switchport trunk allowed vlan 1,40,45,50,55,60
switchport mode trunk
channel-group 1 mode active
interface GigabitEthernet1/0/25
interface GigabitEthernet1/0/26
interface GigabitEthernet1/0/27
interface GigabitEthernet1/0/28
interface Vlan1
ip address 192.168.87.14 255.255.255.0
interface Vlan40
ip address 172.16.10.3 255.255.255.0
no ip http server
ip http secure-server
line con 0
exec-timeout 30 0
password admin
line vty 0 4
access-class vty_ports in
exec-timeout 30 0
password admin
login
length 0
line vty 5 15
access-class vty_ports in
exec-timeout 30 0
password admin
login
end -
WLC 5508: LAG with not stacked switches
Hello!
We are planning to implement the redundant physical connection from 5508 WLC to not stacked 3750 switches.
The sheme is attached.
Is there any way to implement such variant of the topology?When you don't have LAG enabled, you can choose a primary port and a backup port.
Do you mean to choose primary and backup for managment interface?
As it is mentioned in documentation about AP-managment: "You cannot map the AP-manager interface to a backup port"
http://www.cisco.com/en/US/docs/wireless/controller/7.3/configuration/guide/b_wlc-cg_chapter_011.html#ID345 -
Lag function not working in calculated measure
I am facing a strange problem while using "Lag" function in calculated measure.
I have a time dimension which consists of date, workday, financial week, Financial Month and Financial Year.
The concept of workday is its a integer number which represents date. In case of holidays this number donot change and remain constatnt till next working day.
Here workday no remains 460 as 20120708 is a holiday.27 and 28 denotes FinancialWeek.
Now basically I want to find previous wokdays count.
with member [Measures].[Prev Count]
AS
sum(
existing [Date].[Workdayno].[Workdayno].Members,
([Date].[Workdayno].lag(1),[Measures].[Fact Count]))
Select { [Measures].[Prev Count]} on 0,
{[Date].[Calendar].Members} on 1 from [My Cube]
Where([Date].[Calendar].&[20120709])
What I expect that It will give me sum of counts where wokday no is 460.
But its showing null value.
with member [Measures].[PrevCount]
As
SUM(EXISTING [Processing Date].[Workday].[Workday].MEMBERS,([Processing Date].[Workday].LAG(1),[Measures].[Sequenced Records]))
SELECT {[Measures].[PrevCount]} ON 0 FROM --[E2Eitem]
WHERE([Processing Date].[E2E Calendar].[Date].&[20120709])
It looks like existing function is failing to exist the member related to date??
Any suggestion.Try using
with member [Measures].[Prev Count]
AS
sum(
existing [Date].[Workdayno].[Workdayno].Members,
([Date].[Workdayno].currentmember.lag(1),[Measures].[Fact Count]))
Victor Rocca -
After I upgraded to Maverick my Epson WF-2504 scanner will not work. There is no software update showing necessary either. I have gone to the Epson website but it doesn't offer a download. It tells me to go to "software update" ??? Any suggestions?
Thanks Arthur,
I was hoping for a good bubble bursting, but I tried that HP "update" as soon as my printer stopped responding. I really really wanted my bubble popped.
One needs the Apple supplied driver for this work. It will not work because the driver to basically function on the updated Mavericks is not supplied by Apple Updates, so the HP driver that stops printing an extra page is rendered useless. I spent, wasted two days going back and forth between Support threads, HP chat and on the phone, through all the Mac channels where I was told that the 2011 HP was antique. HP said Apple had the drivers. So, they pointed a finger at one another with this unlucky customer caught in the crossfire. HP said Mac did it and Mac said HP did it. BOOM ! goes the guy in between who spent a good bit of money to have good equipment. What is wrong with expecting a printer to last beyond 3 years, or for a back up drive to last more than 3 years?
I do appreciate the attempt to help though. It was here in Discussions where I was guided to the gimp driver, drivers which in the past always worked when needed but in this case something wicked about Mavericks prevents it from working. No matter how many times HP says it works on their site all you have to do is try and then speak with customer service to find out that in a parellel universe this may logically hold. It does not hold here. If it were the case that by working in Lion it would work in Mavericks then there must be something wrong with me. But why, APPLE, is it that one day it works, do the update and then it does not when Lion was the previous OS? I did Everything, every single thing recommended by people who had good ideas and wanted to help but all too often the facts tell us nothing of the world. Facts are tools used to decieve, the world is where it works or does not work and in this case Mavericks has cost me close to $300. Probably not a big deal in some cases, but money is money. When it is gone it is gone.
I followed the complete uninstall, going into library and removing all HP, then restarting and lo and behold HP driver for 4500 not only was not present but along the way my 500gig back up drive died, as in dead, nothing.
Of course I will not buy another HP product. If you go to the list of drivers Mac says it carries the HP Officejet 4500 wireless may be present but is not carried by Apple. I have tried Apple update over and over. What I have done is wasted my time and money. In one fell update I lost a printer and a back up drive. No storms, no loss of electricity, no boogie men lurking, no malware, no gremlins, nothing but an innocent customer updating when Apple said "update". Sure it is serendipity that both my printer and back up drive died on the same day at the same time following the Mavericks update. Who am I but a loyal customer? I must be stupid because my equipment stopped responding after the update. It is not new that there are bugs and glitches following updates. I was a beta tester for OS X, it wiped my computer clean, but I understood, it was beta.
A friend told me the same about planned obsolescence in that since printers are cheap and ink is expensive they don't really care about customer satisfaction. Three years old is antique, out of date. We should and must all be angered by this hatred for the customer shown by manufacturers across the board. Blaming the customer is ridiculous and absurd but not unheard of, in fact it has become the rule of thumb from the other side. The customer is innocent. All we want is to buy premium equipment and to have it behave in a manner befitting the cost. I am an Apple user since 1994. I designed a restaurant on a 333 mhz black and white Mac. You know, the big floppy disc one. I am not new to Apple. Fiercely loyal for 20 years. This is the most angered I have been by the flippant attitude shown to us all.
Thank you for giving the links and hopeful advice. I tried them all when I first had the troubles. The good people in discussions, not the Apple plants, but the users, tried their best. I thought that by coming back later there would be updates and new links that would help. But no. Maybe one day. HP lost a customer, it means nothing to any of the manufacturers when a customer is ridiculed by their cynical attitude towards the customer. Maybe there will be someone else to come along here that has had similar experiences and found a way to fix. Used to be a gimp driver could do the trick. Used to be a way. I fear we lose control of our equipment more and more every day. This is not a rant. It is a somewhat sad expression of having been ripped off. Discussions here have helped in the past but the more things advance the less we matter. And as in the past when I was mad about an Apple failure a member sent a fix and I printed the fix for others to use in return. We help one another in the best of ways. Please spread the word, maybe there will be a fix to show up here sometime. I kissed my iOmega back up drive and the 500 gigs of writings, photos, backups and music goodbye, gone forever, poof! But the HP printer is still here on my desk. I don't want to give up hope. -
C3850 WLC enabled and WLC 2504, which one should be Primary controller.
I have 2 designs to make a better solution, please advise me.
I have C3850 and WLC 2504.
1. I will use C3850 as mobility controller (MC) and mobility agent (MA) for WLC 2504. Does it work? or
2. I will use WLC 2504 as MC and MA for C3850.
Can I do both of design?
Which one is better?
Please recommend me a solution.
Thank you in advance.Hi
2504 (or any legacy WLC) itself having MC/MA & we cannot separate that role on it. You can seperate MC & MA functionality in Converged Access product platforms (3850/3650) only.
Therefore here are the answer to your queries
1. You can have a 3850 with MC/MA functionality. But your 2504 will be a separate controller on your mobility domain. You can allow roaming between these two systems configuring them as mobility peers. You cannot register 3850 connected APs to any other controller other than 3850 WLC itself.So you cannot use these two different system as high availability for AP.
You need to have min 7.6.x on your 2504 in order to configure mobility between 2504 & Converged Access system.
Here is a reference post how you configure roaming between 5508 & Converged Access MC (5760/3850/3650)
http://mrncciew.com/2014/05/06/configuring-new-mobility/
2. None of the documents listed the 2504 could act as MC for 3850/3650(MA). So my understanding is you should have 5760/5508/WiSM2/8500 as MC. But you can test it & see whether 2504 could act as MC which I doubted.
HTH
Rasika
**** Pls rate all useful responses **** -
Local printers not working with 2504 WLC
I have a 2504 WLC with 3 1262 WAPs in lightweight mode.
Clients connect using WPA2 PSK AES with no problem. Clients are Windows XP Home SP3. Test pages end up in print queue and eventually get a error printing status. Clients are not part of a domain and in a standalone workgroup - techstream.
Printer can be pinged from wireless client.
Another 1262N WAP in standalone mode connected to same lan from windows 7 sp1 clients have no problem printing to a local printer.
What does work on the Windows XP Home client is connecting to a network shared printer authenticating with domain admin id and password and it works. Reboot and the network shared printer can not connect multiple reasons are "access is denied" and message box says "only security tab will be displayed....." Another Windows XP Home SP3 client on reboot can't open the network shared printer with message "Can't find printer"
The local printers do work on these pc's with an old colubris router that has an outside interface on our lan and internal network with clients getting dhcp address from colubris router of 192.168.3.XXX .
What is wrong with the wireless 2504 WLC?
Thanks
Broadcast forwarding was enabled.Although a cisco tech support was helpful in making sure multicasting was enabled and a multicast server defined, the problem was at the CP2025DN printer. It had old network ip mask and gateway configured on the printer.
The new devices were part of the new network configuration (Mask and gateway had changed). I didn’t change that printer when I changed all the other printers at the facility because it was still active thru the old wireless network. I forgot to change the printer ip config when I brought the new wap on the new wireless network with the wlc 2504.
End result was the clients were part of a different subnet and gateway configuration then the printer and this disrupted the communication between clients and the printer. Once I corrected the mask and gateway on the printer to be the same as the dhcp scope of the wireless network, communication and printing worked.
Problem solved. User error -
Client got not connection to wlan over wlc 2504 on 802.11b/g
Hi everybody,
We are using a wlc 2504 with 7.6.100.0 and AP 1532e.
I have the strange observacion that only clients with 802.11n (2.4GHz) can connect to the WLAN. Clients thats works only with 802.11b/g, they can't connect to the WLAN. Affected are all machines which want to connect with 802.11b/g.
This is a MESH WLAN with 5GHz backhaul and 2.4GHz for the user.
During the debugging found the following:
*apfMsConnTask_4: May 09 11:44:40.581: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
*apfMsConnTask_4: May 09 11:44:40.581: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
*spamApTask6: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: New PMKID: (16)
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 EAPOL Header:
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00000000: 02 03 00 5f ..._
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: Including PMKID in M1 (16)
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Allocating EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:40.585: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_0: May 09 11:44:40.585: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*Dot1x_NW_MsgTask_0: May 09 11:44:40.585: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*Dot1x_NW_MsgTask_0: May 09 11:44:40.585: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:44:42.649: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0 Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:44:44.649: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:44:44.649: 00:1b:77:b4:34:e0 Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:44:44.649: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*dot1xMsgTask: May 09 11:44:44.649: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*dot1xMsgTask: May 09 11:44:44.649: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*dot1xMsgTask: May 09 11:44:44.650: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:44:46.649: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Retransmit failure for EAPOL-Key M1 to mobile 00:1b:77:b4:34:e0, retransmit count 3, mscb deauth count 1
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Sent Deauthenticate to mobile on BSSID 18:9c:5d:71:34:50 slot 0(caller 1x_ptsm.c:598)
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Deleting the PMK cache when de-authenticating the client.
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Global PMK Cache deletion failed.
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station: (callerId: 57) in 10 seconds
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Freeing EAP Retransmit Bufer for mobile 00:1b:77:b4:34:e0
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Reassociation received from mobile on BSSID 18:9c:5d:71:34:50
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Global 200 Clients are allowed to AP radio
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Max Client Trap Threshold: 0 cur: 1
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Rf profile 600 Clients are allowed to AP wlan
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 1
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Re-applying interface policy for client
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2202)
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2223)
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 In processSsidIE:4795 setting Central switched to TRUE
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 In processSsidIE:4798 apVapId = 1 and Split Acl Id = 65535
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Applying site-specific Local Bridging override for station 00:1b:77:b4:34:e0 - vapId 1, site 'default-group', interface 'catodos'
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Applying Local Bridging Interface Policy for station 00:1b:77:b4:34:e0 - vlan 1, interface id 12, interface 'catodos'
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 STA - rates (8): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 STA - rates (12): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 extSuppRates statusCode is 0 and gotExtSuppRatesElement is 1
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Processing RSN IE type 48, length 20 for mobile 00:1b:77:b4:34:e0
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Initializing policy
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Central switch is TRUE
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Not Using WMM Compliance code qosCap 00
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:9c:5d:71:34:50 vapId 1 apVapId 1 flex-acl-name:
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 apfPemAddUser2:session timeout forstation 00:1b:77:b4:34:e0 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is 0
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station: (callerId: 49) in 1800 seconds
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
*spamApTask6: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: New PMKID: (16)
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 EAPOL Header:
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00000000: 02 03 00 5f ..._
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: Including PMKID in M1 (16)
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Allocating EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:44:54.249: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0 Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:44:56.249: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0 Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:44:58.249: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:44:58.249: 00:1b:77:b4:34:e0 Retransmit failure for EAPOL-Key M1 to mobile 00:1b:77:b4:34:e0, retransmit count 3, mscb deauth count 2
*dot1xMsgTask: May 09 11:44:58.249: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:44:58.249: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:44:58.249: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
*dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Sent Deauthenticate to mobile on BSSID 18:9c:5d:71:34:50 slot 0(caller 1x_ptsm.c:598)
*dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
*dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Deleting the PMK cache when de-authenticating the client.
*dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Global PMK Cache deletion failed.
*dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station: (callerId: 57) in 10 seconds
*dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Freeing EAP Retransmit Bufer for mobile 00:1b:77:b4:34:e0
*apfMsConnTask_4: May 09 11:45:03.768: 00:1b:77:b4:34:e0 Reassociation received from mobile on BSSID 18:9c:5d:71:34:50
*apfMsConnTask_4: May 09 11:45:03.768: 00:1b:77:b4:34:e0 Global 200 Clients are allowed to AP radio
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Max Client Trap Threshold: 0 cur: 1
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Rf profile 600 Clients are allowed to AP wlan
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 1
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Re-applying interface policy for client
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2202)
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2223)
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 In processSsidIE:4795 setting Central switched to TRUE
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 In processSsidIE:4798 apVapId = 1 and Split Acl Id = 65535
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Applying site-specific Local Bridging override for station 00:1b:77:b4:34:e0 - vapId 1, site 'default-group', interface 'catodos'
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Applying Local Bridging Interface Policy for station 00:1b:77:b4:34:e0 - vlan 1, interface id 12, interface 'catodos'
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 STA - rates (8): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 STA - rates (12): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 extSuppRates statusCode is 0 and gotExtSuppRatesElement is 1
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Processing RSN IE type 48, length 20 for mobile 00:1b:77:b4:34:e0
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Initializing policy
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Central switch is TRUE
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Not Using WMM Compliance code qosCap 00
*apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:9c:5d:71:34:50 vapId 1 apVapId 1 flex-acl-name:
*apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
*apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 apfPemAddUser2:session timeout forstation 00:1b:77:b4:34:e0 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is 0
*apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station: (callerId: 49) in 1800 seconds
*apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
*apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
*apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
*spamApTask6: May 09 11:45:03.772: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: New PMKID: (16)
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 EAPOL Header:
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00000000: 02 03 00 5f ..._
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: Including PMKID in M1 (16)
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Allocating EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:45:05.849: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0 Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:45:07.848: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0 Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:45:09.848: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 Retransmit failure for EAPOL-Key M1 to mobile 00:1b:77:b4:34:e0, retransmit count 3, mscb deauth count 3
*dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 Blacklisting (if enabled) mobile 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Change state to START (0) last state 8021X_REQD (3)
*dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Reached FAILURE: from line 5274
*dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station: (callerId: 9) in 10 seconds
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Reassociation received from mobile on BSSID 18:9c:5d:71:34:50
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Global 200 Clients are allowed to AP radio
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Max Client Trap Threshold: 0 cur: 1
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Rf profile 600 Clients are allowed to AP wlan
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 1
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Re-applying interface policy for client
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2202)
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2223)
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 In processSsidIE:4795 setting Central switched to TRUE
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 In processSsidIE:4798 apVapId = 1 and Split Acl Id = 65535
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Applying site-specific Local Bridging override for station 00:1b:77:b4:34:e0 - vapId 1, site 'default-group', interface 'catodos'
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Applying Local Bridging Interface Policy for station 00:1b:77:b4:34:e0 - vlan 1, interface id 12, interface 'catodos'
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 STA - rates (8): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 STA - rates (12): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 extSuppRates statusCode is 0 and gotExtSuppRatesElement is 1
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Processing RSN IE type 48, length 20 for mobile 00:1b:77:b4:34:e0
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Initializing policy
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Central switch is TRUE
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Not Using WMM Compliance code qosCap 00
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:9c:5d:71:34:50 vapId 1 apVapId 1 flex-acl-name:
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 apfPemAddUser2:session timeout forstation 00:1b:77:b4:34:e0 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is 0
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station: (callerId: 49) in 1800 seconds
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
*apfMsConnTask_4: May 09 11:45:15.691: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
*spamApTask6: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: New PMKID: (16)
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 EAPOL Header:
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00000000: 02 03 00 5f ..._
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: Including PMKID in M1 (16)
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Reusing allocated memory for EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*apfMsConnTask_4: May 09 11:45:15.875: 00:1b:77:b4:34:e0 Reassociation received from mobile on BSSID 18:9c:5d:71:34:50
*apfMsConnTask_4: May 09 11:45:15.875: 00:1b:77:b4:34:e0 Global 200 Clients are allowed to AP radio
*apfMsConnTask_4: May 09 11:45:15.875: 00:1b:77:b4:34:e0 Max Client Trap Threshold: 0 cur: 1
*apfMsConnTask_4: May 09 11:45:15.875: 00:1b:77:b4:34:e0 Rf profile 600 Clients are allowed to AP wlan
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 1
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Re-applying interface policy for client
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2202)
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2223)
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 In processSsidIE:4795 setting Central switched to TRUE
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 In processSsidIE:4798 apVapId = 1 and Split Acl Id = 65535
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Applying site-specific Local Bridging override for station 00:1b:77:b4:34:e0 - vapId 1, site 'default-group', interface 'catodos'
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Applying Local Bridging Interface Policy for station 00:1b:77:b4:34:e0 - vlan 1, interface id 12, interface 'catodos'
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 STA - rates (8): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 STA - rates (12): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 extSuppRates statusCode is 0 and gotExtSuppRatesElement is 1
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Processing RSN IE type 48, length 20 for mobile 00:1b:77:b4:34:e0
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Initializing policy
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Change state to AUTHCHECK (2) last state 8021X_REQD (3)
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Central switch is TRUE
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Not Using WMM Compliance code qosCap 00
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:9c:5d:71:34:50 vapId 1 apVapId 1 flex-acl-name:
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
*apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 apfPemAddUser2:session timeout forstation 00:1b:77:b4:34:e0 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is 0
*apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station: (callerId: 49) in 1800 seconds
*apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
*apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
*apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
*spamApTask6: May 09 11:45:15.878: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: New PMKID: (16)
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 EAPOL Header:
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00000000: 02 03 00 5f ..._
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: Including PMKID in M1 (16)
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Reusing allocated memory for EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:45:18.048: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0 Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:45:20.049: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0 Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:45:22.048: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Retransmit failure for EAPOL-Key M1 to mobile 00:1b:77:b4:34:e0, retransmit count 3, mscb deauth count 0
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Sent Deauthenticate to mobile on BSSID 18:9c:5d:71:34:50 slot 0(caller 1x_ptsm.c:598)
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Deleting the PMK cache when de-authenticating the client.
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Global PMK Cache deletion failed.
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station: (callerId: 57) in 10 seconds
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Freeing EAP Retransmit Bufer for mobile 00:1b:77:b4:34:e0
*osapiBsnTimer: May 09 11:45:32.048: 00:1b:77:b4:34:e0 apfMsExpireCallback (apf_ms.c:625) Expiring Mobile!
*apfReceiveTask: May 09 11:45:32.049: 00:1b:77:b4:34:e0 apfMsExpireMobileStation (apf_ms.c:6632) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Disassociated
*apfReceiveTask: May 09 11:45:32.049: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station: (callerId: 45) in 10 seconds
Thanks for any adviceIn some of the big name brands of wireless, there is "no such thing" as 802.11n on a 2.4 Ghz. No such thing because Cisco won't allow you (any more) to do channel bonding of 2.4 Ghz. It doesn't make any sense to bond an already restricted 2.4 Ghz non-overlapping channel (three) and squeeze this number down to two.
Can you check to ensure that the data rates for 802.11b are enabled? Maybe someone disabled data rates from 1 Mbps to 11 Mbps. -
HELP: WLC AP-SSO not working (standby unity in maintenance mode)
I have two WLC version 7.3.101.0 with the standby unit having HA-SKU. I have tested the AP-SSO functionality without any problem in lab with direct connection on RP port between two WLC. Once I brought them into data centre in separate location (latency is less than 10ms between the two DC), the standby unity always went into maintenance mode. The booting process on standby unit went to maintenance mode as shown below:
Management Gateway and Peer Redundancy Management interface are not reachable.
Entering maintenance mode...
I have checked on the core switches at 2 data centre that the two WLC RP ports are connected to same VLAN and it is spanned across MAN link (10GB and less than 10ms delay). The spanning tree on those ports are forwarding as well.
I have rebooted the second unit but no luck.
The interface between two DC is using MTU 9216 which I do not think would cause this issue.
Anyone has come across same or similar issue with me or know the solution? If you do, plz enlighten me.
ThanksThanks Leo and Scott for your feedback. I notice there are two newer software for WLC version 7.3.102.0 and 7.4.100.0.
Both of them seem to have many open caveats. In my wireless environment, I also use ISE, MSE and Prime Infrastructure and unfortunately WLC 7.4 does not support prime solution and MSE yet according to below compatibility matrix.
http://www.cisco.com/en/US/docs/wireless/controller/5500/tech_notes/Wireless_Software_Compatibility_Matrix.html
I think I only have choice to do minor upgrade to 7.3.102.0 at this moment (please correct me if I am wrong). This software was published on 30th Jan 2013 so I wonder if someone else has tried this and managed to get WLC AP-SSO setup working flawlessly where 2nd WLC unit is at different location?
Appreciate for more info and advise. -
WLC 2106_AP-1131_dell vostro 14 v3446 wifi not working with WLC
Hi,
I'm facing issue with newly purchased Dell laptops(dell vostro 14 v3446) are not able to join in WLC.
I have check WLAN profile for these laptops ,all mapped correct,but laptops not able to join the same profile.
Only one(newly purchased) laptop is working fine with WLC profile,remaining laptop all config is same but not getting connected with WLC.
Laptop wifi is working with another vendor APs.
But this particular profile working with my exciting user's laptop perfectly.
WLC/-AIR-WLC2106-K9-Firmware version—6.0.199.4
AP-AIR-LAP1131AG-A-K9.
Please advice me here to resolve this problem.
regards,vijesh
This was posted in lieu of blog https://supportforums.cisco.com/node/12292096 which was deleted since questions should be questions as discussions as not as blogs ;-)Hi Leo,
Thanks for your response.
Client laptop trying to connect the SSID and once authentication key entered ,it will try for a while then error message come "could not connect...."
As our suggested,i will create new profile with open authentication,then try to connect the laptop.
we have planned to upgrade WLC firmware in coming weekend. -
Web Auth page not working on WLC
I have a WLC 4402 and I upgraded the s/w from 4.1 to 4.2.176 since I did the web auth on my Guest wlan does not work. I can connect to the wireless ok and when I type in a web address I should get the web auth page but I just get "This page cannot be displayed". However if i type in the ip address of the WLC in the addrsss bar I get the web auth page and it work fine form then on. The web auth page worked fine on ver 4.1. Any ideas?
I opened a TAC case this morning on this same problem, and my solution is what is listed above (config network secureweb cipher-option sslv2 enable)
Basically, SSLv2 is disabled in 4.2. The Default is now SSLv3.
Depending on your Internet settings, if IE is configured to use SSLv2, the webpage will not work.
So in internet explorer, tools, internet options, advanced, There will be a checkbox next to Use SSLv2. (Even if Use SSLv3 is enabled, you still have the https issue).
Basically, my issues was that a select few users could not Web authenticate and a select few admins couldn't HTTPS manage the GUI. Turns out in all cases, the computers that were all able to work, did not have SSLv2 enabled.
By enabling SSLv2, all affected users now work (I think). -
WLC 2504 don't work with mode trunking dot1Q with 3560cg and 2960cg?
Hi
I have a proble with the 3560cg and 2960cg, when i configure the port with "switchport trunk encapsulation doi1q " and "switchport mode trunk" on the interface for the connection with the WLC2504, don't have connection.
I configure others WLC and others switch catalyst (2960, 3550, etc) with the same configuration and this connection work very well.
this is the date from the terminals:
Model SW Version SW Image
WS-C2960CG-8TC-L 12.2(55)EX2 C2960c405ex-UNIVERSALK9-M
Model SW Version SW Image
WS-C3560CG-8TC-S 12.2(55)EX2 C3560c405ex-UNIVERSALK9-M
WLC 2504 IOS-> 7.3.
I don't know what its hapend, or if i need use another command for the 3560cg and 2960cg
RegardsHi scot
in my case, i configure the 3560 with the vlan 1 for administration and the vlan 100 and 200 for my clients (i use the 2 vlans with 2 wlans from the wlc) and i know that the port must be Trunk, my management interface its taggin with the vlan 1 for the administration and the dynamic interfaces with the respective vlan.
when i configure the 3560 and 2960 i use these command (switchport mode trunk) and i loose the connection with the wlc (i use the same comand with other switch and work very well), the wlc loose the conection with the net.
i dont know the reason for this failure, and i know if the wlc have management interface untugged, only work with this vlan (vlan native or vlan access) and don't work with the others vlans for the wlans.
I wish to know if the IOS or if exist another configuration for the 3560 and 2960 works with the WLC correctly or its problem of the IOS
Thaks for the help
Regards -
My macbook air is hanging and its screen is lagging,it is not working smoothly,what should i do?
product-macbook air,intel i5,4gb ram,128gb hardisk,os-10.9.5
my macbook is hanging and its screen is lagging,it is not working smoothly,what should i do?Problem description:
hanging and screen is lagging
EtreCheck version: 2.0.6 (91)
Report generated 29 October 2014 5:14:19 pm IST
Hardware Information: ℹ️
MacBook Air (11-inch, Mid 2013) (Verified)
MacBook Air - model: MacBookAir6,1
1 1.3 GHz Intel Core i5 CPU: 2-core
4 GB RAM Not upgradeable
BANK 0/DIMM0
2 GB DDR3 1600 MHz ok
BANK 1/DIMM0
2 GB DDR3 1600 MHz ok
Bluetooth: Good - Handoff/Airdrop2 supported
Wireless: en0: 802.11 a/b/g/n/ac
Video Information: ℹ️
Intel HD Graphics 5000 -
Color LCD 1366 x 768
System Software: ℹ️
OS X 10.9.5 (13F34) - Uptime: 0:5:17
Disk Information: ℹ️
APPLE SSD TS0128F disk0 : (121.33 GB)
S.M.A.R.T. Status: Verified
EFI (disk0s1) <not mounted> : 210 MB
Macintosh HD (disk0s2) / [Startup]: 120.99 GB (60.95 GB free)
USB Information: ℹ️
Western Digital My Passport 0820 1 TB
S.M.A.R.T. Status: Verified
My Passport (disk1s1) /Volumes/My Passport : 1 TB (690.26 GB free)
Apple Inc. BRCM20702 Hub
Apple Inc. Bluetooth USB Host Controller
Thunderbolt Information: ℹ️
Apple Inc. thunderbolt_bus
Gatekeeper: ℹ️
Mac App Store and identified developers
Launch Agents: ℹ️
[not loaded] com.adobe.AAM.Updater-1.0.plist Support
Launch Daemons: ℹ️
[invalid?] com.adobe.SwitchBoard.plist Support
[loaded] com.microsoft.office.licensing.helper.plist Support
User Launch Agents: ℹ️
[loaded] com.adobe.AAM.Updater-1.0.plist Support
[loaded] com.google.keystone.agent.plist Support
User Login Items: ℹ️
iTunesHelper Application (/Applications/iTunes.app/Contents/MacOS/iTunesHelper.app)
Autodesk 360 Application (/Applications/Autodesk/Autodesk 360.app)
Internet Plug-ins: ℹ️
SharePointBrowserPlugin: Version: 14.0.0 Support
iPhotoPhotocast: Version: 7.0 - SDK 10.8
QuickTime Plugin: Version: 7.7.3
JavaAppletPlugin: Version: 14.9.0 - SDK 10.7 Check version
Default Browser: Version: 537 - SDK 10.9
User Internet Plug-ins: ℹ️
iGetterScriptablePlugin: Version: 2.9.2 Support
Safari Extensions: ℹ️
iGetter Extension
3rd Party Preference Panes: ℹ️
None
Time Machine: ℹ️
Skip System Files: NO
Auto backup: YES
Volumes being backed up:
Macintosh HD: Disk size: 120.99 GB Disk used: 60.04 GB
Destinations:
My Passport [Local]
Total size: 1 TB
Total number of backups: 4
Oldest backup: 2014-10-26 17:07:25 +0000
Last backup: 2014-10-29 10:50:49 +0000
Size of backup disk: Excellent
Backup size 1 TB > (Disk size 120.99 GB X 3)
Top Processes by CPU: ℹ️
4% WindowServer
1% fontd
0% AppleSpell
0% cfprefsd
0% imagent
Top Processes by Memory: ℹ️
107 MB mds_stores
86 MB Google Chrome
60 MB Google Chrome Helper
43 MB WindowServer
39 MB Finder
Virtual Memory Information: ℹ️
2.10 GB Free RAM
1.31 GB Active RAM
350 MB Inactive RAM
537 MB Wired RAM
668 MB Page-ins
0 B Page-outs -
WLCS 3.1 + WLS SP 9 --*** PORTALS Not WORKING!!!!
After applying WLS SP 9.0 our portals not working.
Can anybody throw some light, PLEASE !!! **URGENT**
We are getting the following Error:
Sun May 06 21:24:44 GMT+03:00 2001:<E> <ServletContext-General> Servlet failed
with Exception weblogic.servlet.jsp.JspException: (line -1): Error in tag library
at: 'wl': The Tag class 'weblogi x.jsp.tags.CacheTag' has no setter method corresponding
to TLD declared attribute 'async', (JSP 1. spec, 5.4.1) at java.lang.Throwable.fillInStackTrace(Native
Method) at java.lang.Throwable.fillInStackTrace(Compiled Code) at java.lang.Throwable.<init>(Compiled
Code) at java.lang.Exception.<init>(Compiled Code) at java.lang.RuntimeException.<init>(Compiled
Code) at weblogic.servlet.jsp.JspException.<init>(Compiled Code) at weblogic.servlet.jsp.JspException.<init>(Compiled
Code) at weblogic.servlet.jsp.StandardTagLib.jspException(Compiled Code) at weblogic.servlet.jsp.StandardTagLib.processTag(Compiled
Code) at weblogic.servlet.jsp.StandardTagLib.processTagElements(Compiled Code)
at weblogic.servlet.jsp.StandardTagLib.<init>(Compiled Code) at weblogic.servlet.jsp.JspLexer.loadTagLib(Compiled
Code) at weblogic.servlet.jsp.JspLexer.mTAGLIB_DIRECTIVE_BODY(Compiled Code) at
weblogic.servlet.jsp.JspLexer.mTAGLIB_DIRECTIVE(Compiled Code) at weblogic.servlet.jsp.JspLexer.mDIRECTIVE(Compiled
Code) at weblogic.servlet.jsp.JspLexer.mSTANDARD_THING(Compiled Code) at weblogic.servlet.jsp.JspLexer.mTOKEN(Compiled
Code) at weblogic.servlet.jsp.JspLexer.nextToken(Compiled Code) at weblogic.servlet.jsp.JspLexer.parse(Compiled
Code) at weblogic.servlet.jsp.JspParser.doit(Compiled Code) at weblogic.servlet.jsp.JspParser.parse(Compiled
Code) at weblogic.servlet.jsp.Jsp2Java.outputs(Compiled Code) at weblogic.utils.compiler.CodeGenerator.generate(Compiled
Code) at weblogic.servlet.jsp.JspStub.compilePage(Compiled Code) at weblogic.servlet.jsp.JspStub.prepareServlet(Compiled
Code) at weblogic.servlet.jsp.JspStub.checkForReload(Compiled Code) at weblogic.servlet.internal.ServletStubImpl.getServlet(Compiled
Code) at weblogic.servlet.internal.ServletStubImpl.invokeServlet(Compiled Code)
at weblogic.servlet.internal.RequestDispatcherImpl.forward(Compiled Code) at com.beasys.commerce.foundation.flow.ServletDestinationHandler.handleDestination(Compiled
Code) at com.beasys.commerce.foundation.flow.FlowManager.service(Compiled Code)
at javax.servlet.http.HttpServlet.service(Compiled Code) at weblogic.servlet.internal.ServletStubImpl.invokeServlet(Compiled
Code) at weblogic.servlet.internal.ServletContextImpl.invokeServlet(Compiled Code)
at weblogic.servlet.internal.ServletContextImpl.invokeServlet(Compiled Code) at
weblogic.servlet.internal.ServletContextManager.invokeServlet(Compiled Code) at
weblogic.socket.MuxableSocketHTTP.invokeServlet(Compiled Code) at weblogic.socket.MuxableSocketHTTP.execute(Compiled
Code) at weblogic.kernel.ExecuteThread.run(Compiled Code)I have gotten it to work by replacing the sp9 weblogic-tags-510.jar with
the sp8 weblogic-tags-510.jar. We haven't experienced any problems with
our app after using this workaround. However, we haven't completely
tested it either.
psimon wrote:
You should use sp6 or sp8 instead of sp9
Pascal
Nadeem a écrit :
After applying WLS SP 9.0 our portals not working.
Can anybody throw some light, PLEASE !!! **URGENT**
We are getting the following Error:
Sun May 06 21:24:44 GMT+03:00 2001:<E> <ServletContext-General>
Servlet failed
with Exception weblogic.servlet.jsp.JspException: (line -1): Error
in tag library
at: 'wl': The Tag class 'weblogi x.jsp.tags.CacheTag' has no setter
method corresponding
to TLD declared attribute 'async', (JSP 1. spec, 5.4.1) at
java.lang.Throwable.fillInStackTrace(Native
Method) at java.lang.Throwable.fillInStackTrace(Compiled Code) at
java.lang.Throwable.<init>(Compiled
Code) at java.lang.Exception.<init>(Compiled Code) at
java.lang.RuntimeException.<init>(Compiled
Code) at weblogic.servlet.jsp.JspException.<init>(Compiled Code) at
weblogic.servlet.jsp.JspException.<init>(Compiled
Code) at weblogic.servlet.jsp.StandardTagLib.jspException(Compiled
Code) at weblogic.servlet.jsp.StandardTagLib.processTag(Compiled
Code) at
weblogic.servlet.jsp.StandardTagLib.processTagElements(Compiled
Code)
at weblogic.servlet.jsp.StandardTagLib.<init>(Compiled Code) at
weblogic.servlet.jsp.JspLexer.loadTagLib(Compiled
Code) at
weblogic.servlet.jsp.JspLexer.mTAGLIB_DIRECTIVE_BODY(Compiled Code)
at
weblogic.servlet.jsp.JspLexer.mTAGLIB_DIRECTIVE(Compiled Code) at
weblogic.servlet.jsp.JspLexer.mDIRECTIVE(Compiled
Code) at weblogic.servlet.jsp.JspLexer.mSTANDARD_THING(Compiled
Code) at weblogic.servlet.jsp.JspLexer.mTOKEN(Compiled
Code) at weblogic.servlet.jsp.JspLexer.nextToken(Compiled Code) at
weblogic.servlet.jsp.JspLexer.parse(Compiled
Code) at weblogic.servlet.jsp.JspParser.doit(Compiled Code) at
weblogic.servlet.jsp.JspParser.parse(Compiled
Code) at weblogic.servlet.jsp.Jsp2Java.outputs(Compiled Code) at
weblogic.utils.compiler.CodeGenerator.generate(Compiled
Code) at weblogic.servlet.jsp.JspStub.compilePage(Compiled Code) at
weblogic.servlet.jsp.JspStub.prepareServlet(Compiled
Code) at weblogic.servlet.jsp.JspStub.checkForReload(Compiled Code)
at weblogic.servlet.internal.ServletStubImpl.getServlet(Compiled
Code) at
weblogic.servlet.internal.ServletStubImpl.invokeServlet(Compiled
Code)
at weblogic.servlet.internal.RequestDispatcherImpl.forward(Compiled
Code) at
com.beasys.commerce.foundation.flow.ServletDestinationHandler.handleDestination(Compiled
Code) at
com.beasys.commerce.foundation.flow.FlowManager.service(Compiled
Code)
at javax.servlet.http.HttpServlet.service(Compiled Code) at
weblogic.servlet.internal.ServletStubImpl.invokeServlet(Compiled
Code) at
weblogic.servlet.internal.ServletContextImpl.invokeServlet(Compiled
Code)
at
weblogic.servlet.internal.ServletContextImpl.invokeServlet(Compiled
Code) at
weblogic
servlet.internal.ServletContextManager.invokeServlet(Compiled Code)
at
weblogic.socket.MuxableSocketHTTP.invokeServlet(Compiled Code) at
weblogic.socket.MuxableSocketHTTP.execute(Compiled
Code) at weblogic.kernel.ExecuteThread.run(Compiled Code)
Maybe you are looking for
-
How to Execute WebDynpro Applications as Background Job ?
Hi Gurus, We have developed a lot of WDJ applications with component reusage; ie, quite a lot of business logic are wrapped in WDJ Components which are re-used by other WD UIs. Now we'd like to automate some of the processes with background jobs and
-
Correct quotes for non-english languages?
RH8 ignores the language setting of my project and inserts English quotes ("..") instead of German ones („.."). Is there an easy way to insert a lower quote („) without doing it manually in the HTML code?
-
My default browser is firefox, but internet explorer is coming in too. I was trying to check my default and internet explorer setting came up. I having a delay on my website and I think it is internet explorer. I know some programs requires internet
-
hi i m using Oracle developer suit 10g and Designer version is 9.0.4.2.8.....i made a user and assigned all privileges to that user listed in "Check Requiements" butoon in RAU...i installed repository but now when i run Oracle Designer..it gives me e
-
Why does the design view (horizontal) change to a square when i look at the site in the browser preview and/or test mode? I am using the default setting and have tried it numerous ways -- w/ gray browser fill, with an image as browser fill, etc. I h