2811 and VIC2-2BRI-NT/TE. CCM 4.1.3

Hi,
I've an H323 gateway with a VIC2-2BRI-NT/TE to connect directly an ISDN Phone. I'm searching to display a name for this phone when it call an IP Phone. Anyone an idea ? The station-name voice-port command doesn't work with BRI interface. Thanks

Here it is :
boot system flash:c2800nm-spservicesk9-mz.124-4.XC1.bin
isdn switch-type basic-net3
voice-card 0
no dspfarm
voice class h323 1
h225 timeout tcp establish 3
call preserve
interface BRI0/0/0
no ip address
isdn switch-type basic-net3
isdn overlap-receiving
isdn protocol-emulate network
isdn layer1-emulate network
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn outgoing display-ie
isdn skipsend-idverify
line-power
interface BRI0/0/1
no ip address
isdn switch-type basic-net3
isdn overlap-receiving
isdn protocol-emulate network
isdn layer1-emulate network
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn outgoing display-ie
isdn skipsend-idverify
line-power
ip route 0.0.0.0 0.0.0.0 X.Y.Z.W
voice-port 0/0/0
compand-type a-law
cptone CH
dial-peer voice 10 pots
tone ringback alert-no-PI
preference 1
destination-pattern 4976
direct-inward-dial
port 0/0/1
forward-digits all
dial-peer voice 20 voip
preference 1
destination-pattern 6671
progress_ind setup enable 3
voice-class h323 1
session target ipv4:10.16.246.41
codec g711ulaw
ip qos dscp cs5 media
no vad
dial-peer voice 21 voip
preference 2
destination-pattern 6671
progress_ind setup enable 3
session target ipv4:10.19.133.41
codec g711ulaw
ip qos dscp cs5 media
no vad

Similar Messages

  • Trouble with CCME 4 and VIC2-2FXO; IOS 12.4(9)T

    Trouble with CCME 4 and VIC2-2FXO; IOS 12.4(9)T
    I am having trouble making outgoing call or answering incoming call.
    When I try to call out from my IP 7961 phone, it fails with the message "unknown number".
    For incoming call, it rings but when I pick up the call nothing happens,
    Put the receiver back on hook, the phone carries on ringing. I am in UK
    and just trying to set up test system with one analogue line. Any help will
    be most appreciated. My config of the 2811 router is posted below. All calls ineternally works fine.
    Thank you for your help.
    hostname Test-CME
    ip cef
    no ip dhcp use vrf connected
    ip dhcp excluded-address 10.10.10.1 10.10.10.10
    ip dhcp excluded-address 10.139.139.1 10.139.139.10
    ip dhcp pool host
    network 10.10.10.0 255.255.255.0
    default-router 10.10.10.1
    option 150 ip 10.10.10.1
    ip dhcp pool data
    network 10.139.139.0 255.255.255.0
    default-router 10.139.139.1
    dns-server 10.139.139.5
    voice-card 0
    no dspfarm
    voice service voip
    allow-connections h323 to h323
    allow-connections h323 to sip
    allow-connections sip to h323
    allow-connections sip to sip
    supplementary-service h450.12
    h323
    sip
    header-passing
    registrar server expires max 3600 min 3600
    interface FastEthernet0/1
    no ip address
    no ip mroute-cache
    duplex auto
    speed auto
    no shut
    interface FastEthernet0/1.2
    description ** Data VLAN **
    encapsulation dot1Q 2
    ip address 10.139.139.1 255.255.255.0
    interface FastEthernet0/1.3
    description ** Voice VLAN **
    encapsulation dot1Q 3
    ip address 10.10.10.1 255.255.255.0
    ip http server
    ip http authentication local
    no ip http secure-server
    ip http path flash:
    tftp-server flash:S00104000100.sbn
    tftp-server flash:TERM41.7-0-3-0S.loads
    tftp-server flash:term61.default.loads
    tftp-server flash:term41.default.loads
    tftp-server flash:CVM41.2-0-2-26.sbn
    tftp-server flash:cnu41.2-7-6-26.sbn
    tftp-server flash:Jar41.2-9-2-26.sbn
    tftp-server flash:term70.default.loads
    tftp-server flash:term71.default.loads
    tftp-server flash:cnu70.2-7-6-26.sbn
    tftp-server flash:Jar70.2-9-2-26.sbn
    tftp-server flash:TERM70.7-0-3-0S.loads
    tftp-server flash:CVM70.2-0-2-26.sbn
    control-plane
    voice-port 0/3/0
    connection plar opx 202
    caller-id enable
    dial-peer voice 1 pots
    incoming called-number .
    destination-pattern 9T
    port 0/3/0
    telephony-service
    load 7914 S00104000100
    load 7941 TERM41.7-0-3-0S
    load 7961 TERM41.7-0-3-0S
    load 7970 TERM70.7-0-3-0S
    max-ephones 20
    max-dn 40
    ip source-address 10.10.10.1 port 2000
    calling-number initiator
    service phone videoCapability 1
    system message MKC CME
    url services http://10.10.10.1/voiceview/common/login.do
    url authentication
    http://10.10.10.1/voiceview/authentication/authenticate.do
    time-zone 21
    date-format dd-mm-yy
    voicemail 600
    max-conferences 8 gain -6
    call-forward pattern .T
    call-forward system redirecting-expanded
    moh music-on-hold.au
    web admin system name admin secret 0 test
    dn-webedit
    time-webedit
    transfer-system full-consult dss
    transfer-pattern 9.T
    secondary-dialtone 9
    create cnf-files
    ephone-dn 1 dual-line
    number 201
    label 201
    description Sarah
    name Sarah
    ephone-dn 2 dual-line
    number 202
    label 202
    description Vitthal
    name User2 Vitthal
    ephone-dn 3 dual-line
    number 203 secondary
    label 203
    description Neil
    name User3 Neil
    ephone 1
    video
    username "user1" password 201
    mac-address 0018.18EE.947F
    type 7961 addon 1 7914
    button 1:1
    ephone 2
    video
    username "user2" password 202
    mac-address 0018.18BB.B973
    type 7941
    button 1:2
    ephone 3
    video
    username "user3" password 203
    mac-address 0018.1885.6BA2
    type 7970
    button 1:3

    Hi
    Please find enclosed debug attachment for voice ccapi and ephone. First, I called from outside. Extension 202 rings but when I answered on extension 202 nothing happens. Replace the rceiever and the pone starts ringing again.Second step. I tried to call out by dialing 9 and then number but after a while phone displays unknown number.
    Thank you for your help.
    Vitthal

  • ISDN phone on Vic2-2Bri-NT/TE card

    I installed a Vic2-2Bri-NT/TE on our 2851 with CME, when I attach an ISDN phone directly on Vic2-2Bri port I always get busy tone as soon as I pick up the phone. In the log I read :
    ISDN BR0/1/0 Q931: TX -> DISCONNECT pd = 8 callref 0x84
    Cause i = 0x829C - Invalid number format (incomplete number)
    From other IP phone connected on CME I can call the isdn phone, i can also call the isdn call from outside. More over If if configure connection plar on voice port, when I pick up the isdn phone i can call the number setted as connection plar, even when it is an external number.
    But i can't still make a call directly from the isdn phone without connection plar because when i pick up the handset I soon get busy tone.
    Please could anyone give me the right advice?
    Thank you very much in advance.
    Best regards.
    angelo

    Hi Paolo,
    configuring "isdn overlap-receiving" on bri interfaces it works well, I get dial-tone off-hook and then i can make call as usual from isdn phone. I just figuredthet after last digit it makes too much time to start the call, but this is not a big problem.
    Thank you very much for your precious collaboration.
    I hope rated tihis post correctly.
    Regards
    angelo

  • VIC2-2BRI problem

    Hi,
    I need help regarding problem i'm having with ISDN BRI cards.
    The problem is from time to time L1 link goes down between PBX and Cisco 2801 with VIC2-2BRI cards. Problem is not related to a specific type of PBX or just one PBX, but this happens very frequently now, on multiple sites.
    I've managed to find several workaround solutions, but they are far from final.
    1. If i'm using new cards (BRI) and setting a new site, I can't get the cards to go up, that is OK light won't come up, unless I connect straight cable in BRI card, and on the other side connect (short circuit) pins 3,4 and 5,6, make a loop. And here is the "tricky" part, if I don't do shut, no shut cards won't come up, or reload the router and connect cable to card before interfaces come up.
    2. On existing sites link just goes down, all by itself, in that case all that helps is to put the cards in another slot, and use the above method. Cables stay the same, cards and router also, IOS also.
    I really don't see the problem here!
    Has anyone had any similar experiences?
    Thanks
    Regards,
    Damir

    Hi,
    Unfortunately, I don't see the actual transition, it would help me also.
    This is only thing i've found in logs.
    Nov 18 10:49:47: ISDN BR0/2/0 **ERROR**: handle_l2d_srq_mail: Layer 1 inactive
    Nov 18 10:49:50: ISDN BR0/2/0 Q931: L3_ShutDown: Shutting down ISDN Layer 3
    Nov 18 10:49:51.042 CET: %LINK-3-UPDOWN: Interface BRI0/2/0, changed state to down
    But from this I can't see that much...
    Thing is this happens more when you are using new cards, or existing somewhere else.
    Normal cards light up OK when they are going through POST, it tells you that the card is recognized and working. B1 and B2 channels (lights) don't light of course.
    More and more I think this a bug...
    P.S. sorry I can't provide more errors, but this is only thing that happens, that's way it's strange!
    Regards,
    Damir

  • VIC2-2BRI NT/TE - link going down

    Hi,
    I have VIC2-2BRI NT/TE on router 2801.
    If there are no calls for some time, the interfaces are going down, and none outbound call can't be placed.
    Only when inbound call is placed, the link is going up, and everything is working 'till next time.
    Does anybody know what could be the reason?
    Thanks

    I remember i've got a similar problem sometimes ago on the same router and on my 3825 router too.
    But the difference is that the VIC2-2BRI NT/TE remains up until i place calls. The first call goes through one port of the interface, and after that, this port changes state to down. The second call uses the second port of the interface, and after goes down. then i can no more place calls. But i can receive calls from PSTN, and just before, the interfaces change state to UP. And i can place two other calls again and the same problem occur.
    To issue this problem, i entered the command
    " isdn transition-delay 1" at each BRI interface
    And things now go well.
    But i would like to get more information about this command, if you can help me

  • Router 2811 and C2960 Switch Trunking Problem

    Hi all
    I got an problem with a trunking problem between Router 2811 and C2960 switch
    In router 2811 - I created f0/0.1 10.65.20.1 (VLAN 1) and f0/0.48 10.65.23.1 (VLAN 48)
    In C2960 - Vlan 1 10.65.20.30 , VLAN 48 10.65.23.30
    Finally I can only ping VLAN 1 IP but fail to ping VLAN 48 IP, can help me how to troubleshoot it?
    Hugo
    Router 2811 Configuration:
    interface FastEthernet0/0.1
     encapsulation dot1Q 1 native
     ip address 10.65.20.1 255.255.255.0
    interface FastEthernet0/0.48
     encapsulation dot1Q 48
     ip address 10.65.23.1 255.255.255.0
    C2960 Configuration:
    interface FastEthernet0/24
     switchport mode trunk

    2811#sh vlans
    Virtual LAN ID:  1 (IEEE 802.1Q Encapsulation)
       vLAN Trunk Interface:   FastEthernet0/0.1
     This is configured as native Vlan for the following interface(s) :
    FastEthernet0/0
       Protocols Configured:   Address:              Received:        Transmitted:
               IP              10.65.20.1              388873              262275
            Other                                           0                1723
       390760 packets, 71854310 bytes input
       263998 packets, 53723195 bytes output
    Virtual LAN ID:  48 (IEEE 802.1Q Encapsulation)
       vLAN Trunk Interface:   FastEthernet0/0.48
       Protocols Configured:   Address:              Received:        Transmitted:
               IP              10.65.23.1                   0                   0
            Other                                           0                  20
       0 packets, 0 bytes input
       20 packets, 1883 bytes output
    2960_24#sh int trunk
    Port        Mode             Encapsulation  Status        Native vlan
    Fa0/24      on               802.1q         trunking      1
    Gi0/1       on               802.1q         trunking      1
    Port        Vlans allowed on trunk
    Fa0/24      1-4094
    Gi0/1       1-4094
    Port        Vlans allowed and active in management domain
    Fa0/24      1,48
    Gi0/1       1,48
    Port        Vlans in spanning tree forwarding state and not pruned
    Fa0/24      1,48
    Gi0/1       1,48

  • Do Cisco router 2811 and Catalyst 3750 support SNMPv3?

    Hi,
    Do Cisco router 2811, IOS 12.4(20)Ti, and Catalyst 3750, IOS 12.2.(53)SE, support SNMPv3?
    Attached file contains my SNMPv3 configurations and "show snmp" results.  Would you please give me your advice?  Thanks.
    Hugh

    Hugh
    Certainly both the 2811 and the 3750 do support SNMPv3. So support for the feature is not an issue in your situation.
    I have looked at the config that you attached and believe that it looks reasonable. You have not told us about the SNMP server that will communicate with these devices. So we have no way to know if the details of the configuration are correct.
    Have you attempted to discover these devices with an SNMP server that is configured to use SNMPv3 and has this user and passwords configured? If it does not work my first suggestion would be to check to verify that the passwords configured are exactly the same on the clients and on the server (and perhaps re-configure the passwords just to be sure). If the passwords are not a problem my second suggestion would be to check and verify that the authentication and encryption parameters match between the server and the clients.
    HTH
    Rick

  • Issue with VPN compatibility between 2811 and 2911

         hello
    I would like to ask anyone have had any issues with setting up a VPN tunnel between 2811 and 2911?
    The IPSec VPN is established but for some reason I cannot ping the LAN side to the other LAN side of the other end of the VPN Router?
    Any experience would be much appreciated
    Thanks           

    IPSec VPN can be with no problem set up between any cisco routers (and not nesesserely cisco),  so there are should be no issues in your case.
    If you say that tunnel is established successfully, then problem most probably related to routing issues between sites or incorrect crypto-acl configured. Check if hosts on both sites have correct routing information on how to get to subnets on the other site.
    To make more accurate assumptions it would help if you provide config on both sites and describe your topology.

  • ISR 2811 with VIC2-2FXS

    hi,
    We have deployed cisco 2811 router in our network and had installed vic2-2fxs card in one of the HWIC slot.We need to configure fxs card for voip to make a call to branch office and have the following ios c2800nm-ipvoicek9-mz.124-17.bin .The problem we are facing is the router detect vic card under show version command but when show running-config command been given it doesn't display voice-port information to configure the same.We have attached the show tech-support o/p.any suggestion welcomed.

    Hi Bhavesh,
    It Looks like you do not have any DSP resources.You will need something like a PVDM2-8 card on the motherboard to provide DSP resources to the FXS card. Without DSP resources you cannot configure the FXS :)
    Hope this helps!
    Rob

  • Why we dont' see H323 gateway and SIP trunk "registered" in CCM?

    in CCM admin, we see the status of H323 gateways and SIP trunks have no "registered to xxxx" status.

    Unlike devices with other protocols, there is no registration mechanism for these.

  • Testing VIC2-2FX S and VIC2-2FXO cards

    I want to setup two 2611XM routers with a
    NM-HD-2VE ( 3 DSP), VIC2-2FXS, VIC2-2FXO cards.
    Can I connect the FXS to the FXO ?
    Do I need to have telephones with RJ11 Straight through cables connected to the ports of the VIC's.
    Could you point me to somewhere where this scenario is addressed. ( Voice certification test lab diagrams...)
    Thank you,
    Tom

    Dear Experts
    This is going to be my first implimentation of the Voice network and is turning out to be a nightmare.i have reffered all the configuration mannuals , books and videos but still not able to make calls across the MPLS network.Need help urgently to solve the issue.
    Here is the senario
    PSTN>>>FXO(Cisco2905)>>>>>MPLS Cloud<<<<<<<(Cisco2905)FXS>>>>>>>>Phone
    here is the configuration i have done
    <<<<<<<<<>>>>>>>>
    voice-port 0/1/0
    voice-port 0/1/1
    connection plar 2201
    voice-port 0/1/2
    voice-port 0/1/3
    mgcp profile default
    dial-peer voice 998 voip
    destination-pattern 22..
    session target ipv4:192.168.220.1
    dtmf-relay cisco-rtp
    dial-peer voice 100 pots
    destination-pattern 9............
    port 0/1/1
    on
    <<<<<<<<>>>>>>.
    voice-port 0/0/0
    cptone ID
    voice-port 0/0/1
    cptone ID
    mgcp profile default
    dial-peer voice 220 pots
    destination-pattern 2201
    port 0/0/0
    forward-digits all
    dial-peer voice 221 pots
    destination-pattern 2202
    port 0/0/1
    forward-digits all
    dial-peer voice 110 voip
    destination-pattern 9T
    session target ipv4:192.168.0.1
    dtmf-relay cisco-rtp
    =====================================
    Early response is much appriciated
    REGARDS
    SANDEEP

  • GRE IPSec between Cisco 2811 and FortiGate 110C

    Hello,
    Does anybody know if it is possible to configure GRE IPSec tunnel between Cisco 2811 router and FortiGate 110C firewall? I know that FortiGate supports IPSec and GRE tunnels, but maybe somebody succeeded in establishing an IPSec GRE between those routers? Could you also give a link to the appropriate documentation if it is possible?

    Hi,
    You can configure the GRE tunnel on the 2811.
    I'm aware that you can configure sort of a GRE tunnel on the Fortinet as well, but I have not seen a GRE tunnel between a Cisco and other vendor.
    I've only seen GRE tunnels between Cisco devices (however I have not tried it to assure you that it will not work :-()
    Federico.

  • ISDN telephone on VIC2-2BRI-NT/TE

    I have a problem connecting a PBX on a 2800 with vic-2bri-nt/te where the isdn card must be NT. I focused the problem on the tei assignment. The PBX is expecting tei from thr 2800 but it does not supply. I changed the PBX with an ISDN telephone and through debug I see that the router receives tei requests but still does not supply. I tried several commands stll no solution.
    Anyone knows how I can supply tei from the router?

    Try with the command tei-negotiation first call
    http://cisco.com/en/US/products/sw/iosswrel/ps1835/products_configuration_guide_chapter09186a00800ca71c.html

  • X.75 ISDN test setup with 2811 and PVDM2-12DM modem

    Hi all,
    We have a customer that requires ISDN-X.75 connection as a back-up for IP. This is used by emergency services that require redundancy. We have to build a test set-up. We have two routers with the modem cards and with                 HWIC-1CE1T1-PRI=  cards. We need to build a test set-up to simulate an incoming call. With ISDN-V110 we could use one of the routers to place an outgoing call to the other router. This set-up is not possible with X.75, since the card can not dail out. What would be the best/cheapest/simplest approach to build this test set-up?
    My involvement in this project is to build a Perl script that collects data via IOS using expect. If someone has the procedure to collect the calling and called line information for a connection with an example I would be very grateful. Our routers run Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9-M), Version 12.4(24)T1, RELEASE SOFTWARE (fc3).
    For V110/V.34 and X.25 the tty/vty is collected by issueing a show tcp to relate an IP connection that is created to the tty/vty. The tty/vty port is  then correlated to the calling and called line id.  This is done with show x25 vc for X.25 or show modem csm for V.110/V.34. We need something similar for X.75 to distill the calling and called line IDs for a given TCP connection.
    Thanks in advance!

    It colud be Hardware(Digital Modem Module ) problem.
    Try this link:
    http://www.cisco.com/en/US/products/ps6441/products_feature_guide09186a00806b941f.html#wp1068376

  • CCM Configuration Guide and other docs related to CCM

    CCM

    Thanks Jose. I highly appreciate you emailing me those docs.
    In addition if you have SRM 260 SAP Catalog & Content Management, kindly email those to [email protected]
    Thanks and Regards
    Venkatesh
    Edited by: Venkatesh Sriraman on Feb 3, 2008 4:38 PM

Maybe you are looking for