2811(NM-8AM) does not answers incoming call from PC

Dear friends,
We are planning to setup an out of band management connectivity, in our test setup we have a Cisco 2811 ISR (with IOS 12.4(9)T5 ) with NM-8AM (Analog modem module) installed.
Test Setup:
1. One Analog line (PSTN) connected to PC via built-in modem
2. Second Analog line (PSTN) connected to Cisco 2811 (NM-8AM) terminated on the analog modem module
3. Both the analog lines are working fine.
Test Scenario:
1. The router should accept the incoming call from PC. And from the PC we should be able to telnet into the router via dial up connectivity (Out of band)
Test procedure:
1. The Cisco 2811 router is configured as follows:
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Dial-Up-CPE
boot-start-marker
boot-end-marker
logging buffered 16384 debugging
enable password cisco
ip cef
voice-card 0
no dspfarm
username cisco password 0 cisco
interface Loopback0
ip address 10.10.10.1 255.255.255.255
interface FastEthernet0/0
ip address 20.20.20.1 255.255.255.0
duplex auto
speed auto
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
interface Group-Async1
ip unnumbered Loopback0
encapsulation ppp
dialer in-band
dialer idle-timeout 600
dialer-group 1
async mode interactive
peer default ip address pool DIALIN
ppp authentication pap chap
group-range 1/0 1/7
ip local pool DIALIN 172.16.16.1 172.16.16.5
ip http server
no ip http secure-server
dialer-list 1 protocol ip permit
control-plane
line con 0
exec-timeout 0 0
line aux 0
exec-timeout 0 0
password cisco
modem InOut
transport input all
stopbits 1
speed 38400
flowcontrol hardware
line 1/0 1/7
modem InOut
transport input all
stopbits 1
flowcontrol hardware
line vty 0 4
password cisco
scheduler allocate 20000 1000
2. With the above configuration, the router is not able to answer the incoming call from the PC.
3. And from the PC we are able to dial to a PSTN number at the router side, PC gives a proper dial tone and once the number is dialed, the call is landed on the other side (router end) and it rings continuously. But, the router does not answer this incoming. The analog line at the router end is terminated on async interface 1/0.
As I am new to dialup connectivity with NM-8AM, Could some please suggest the proper configuration in our router configuration OR Are missing any commands?
Any links/references would be of great help.
Thank you
Pradeep

Hi,
I guess I'm having exactly the same setup. The integrated modem on the other end does pick up the call but soon disconnect after displaying "Waiting for carrier".
Any clue?
Thanks,
Eyad

Similar Messages

Inter-Trunk not route incoming calls from out

Hi,
I setup one extra gateway where I try to route part of our calls. So far I have success to route internal calls into there, but when I'm making a test call from outside that ends into "number is not used" problem.
I have:
- Route ready, elsewere the internal calls are not working.
- PSTN usage, linked to the Route
- Trunk configuration where I have selected the PSTN usage
- Incoming numbers are coming in E164 format
I have also tested the "Test-CsInterTrunkRouting" and that gives "pass":
FirstMatchingRoute : Description=;NumberPattern=^\+358123654789;Name=Test
                     Gateway;SuppressCallerId=False;AlternateCallerId=
MatchingUsage      : Test PSTN Usage
MatchingRoutes     : {Description=;NumberPattern=^\+358123654789;Name=Test
                     Gateway;SuppressCallerId=False;AlternateCallerId=}
But still, when I made a call from outsited the OCSLogger shows that mediation server try to offer call to Front-End which says only: "SIP/2.0 404 Not Found" and then bye-bye.
What is the missing magic, which made the mediation server to see alternative route? I hope it is not required that mediation server must be collocated on the Front Ends, as that one I do not have.
Any good ideas?
ps.
I'm not sure does it matter, but my Lync gives "SIP/2.0 403 Forbidden" when there is coming call from extra gateway. But as the calls into there works, then I don't see why external calls should not also work.
Petri

Could it be even so, that intra-trunk routing requires consolidated mediation server? As the call is owned by the Mediation server (stanalone), and it is trying to offer that to FE. FE reply "does not exist". Because of the standalone Mediation
server does not have the call routing engine like FE have, the call is lost.
I started to think above as Lync users are able to call to that number. So FE is able to do the routing and get calls into the correct place.
I have to say also, I have read
Ken's blog about inter-trunk routing, I have to say that I'm not so sure what he means by this: "Fortunately, in most cases, adding PSTN usages to the trunk has no effect, since there is almost always a Lync user assigned to the incoming phone
numbers". Why to add additional routing for the numbers which are already inuse? I hope it is not required, that you need to have a users ID for each number you do the inter-trunk routing?
Petri

Phone does not receive incoming calls

Please help. Verizon can't seem to. My phone does not receive 90% of its incoming calls or messages. I have been told to delete all of my messages and call logs- no use. I have tried removing the battery and resetting the phone. I did make sure the phone was not in "do not disturb" mood- it is not. People who call me say that it doesn't ring, just goes straight to voice mail even though the phone is on. Very frustrating problem as my 6 year old phone before seemed to give me better service. I feel like a child who is only allowed to make outgoing calls! Please help. All suggestions are welcome. Thank you.

Check the Call Forwarding section. There are two options to select. One says Forward All Calls and the other says Forward Unanswered Calls. Make sure Forward All Calls is not selected. That would cause all calls to go to the number specified which may be your voicemail. To get there from the home screen click the Phone icon > push the option button (left of the trackball) > click options > click Call Forwarding.

My skype to go number does not take incoming calls

No matter what phone you call from (U.S. landline, various cell carriers, U.K.) you get a message "You have reached a non-working number. Announcement: 14 Switch 1, 8 dash 3."
I have plenty of credit in my account, and can make outgoing calls. But neither my computer when signed in or my stand alone skype phone (IPEVO) when signed in take incoming calls. Do I blame Microsoft?
Either way, it would be nice if someone could help me trouble shoot so we could receive calls again.

Hello,
A SkypeToGo # is the # you call to set up STG calls to your contacts. It's not designed to receive inbound calls which is why you are receiving that message.
To receive inbound calls you require a Skype OnLine #.
TIME ZONE - US EASTERN. LOCATION - PHILADELPHIA, PA, USA.
I recommend that you always run the latest Skype version: Windows & Mac
If my advice helped to fix your issue please mark it as a solution to help others.
Please note that I generally don't respond to unsolicited Private Messages. Thank you.

Uc560 fxo port not answering incoming calls

Hi,
My customer is facing problem for incoming calls in uc560 fxo port.They have 12 PSTN lines which is connected to UC system.System is configured with Auto-Attendant also. almost all days they are facing this major issue of incoming call is not getting answered by UC560 and caller can hear the line is ringing.While the time of this problem I can see some of the FXO port status LED is UP and not disconnecting even if no one is on call also.Once remove the cable from the FXO port and connect it back the problem will solve for time being.What will be the reason for this issue of line getting held.Is there any configuration needs to change in FXO module? Below is the configuration I done on all 12 FXO ports. Please check and
suggest me a solution.

HI Paolo,
Thank you provoding the proper documentation .
On the system side I made the change by keeping companding type from a-law to u-law and enabled battery reverse.This setting works fine for last three days and now again the customer is facing the same problem of FXO port get held and incoming calls are just ringing and system is not answering even.
How to get proper solution for this issue????
Please help me............
Regards,
Rinchuraj

Q10 not answering incoming calls

Incoming calls go right to voicemail.
Subject Title edited to reflect new topic.

OK. Well, that's a pretty ancient OS level...indeed, I don't think that's an OS version at all, but rather the "Software Release". Can you check again please?Article ID: KB23393 How to find the model number and OS version on a BlackBerry smartphoneFurther interesting is that you say you updated the software...strange that something so old would be an update, but I do not know what versions VZW has on their approved list, but that version is definitely quite old...maybe 25 or so updates behind what is truly current from BB. There were many more 10.2.1 releases, then 10.2.2, then 10.3.0, then 10.3.1, and now 10.3.2...each with several versions (at the 4th octet) within. Did you check, in the phone settings, the "Call Forwarding" items to make sure that none of those are set? Failing all of this, the only thing I could recommend is a clean OS reload, and to an OS level that is much more current. If the behavior continues after, then I'd say it's back to VZW to look even deeper into their system. Good luck!

Z10 not answering incoming calls

I have a weird new issue with my z10 (my only issue so far). When an incoming call happens, the screen goes to the PHONE app and freezes there. I cannot do anything to answer the call. Then when the person leaves me a voicemail, I can't get the dialpad to appear to put in my voicemail password. The screen is still frozen on the PHONE app page. I can close that app but the call remains open and if I click on the call (at the bottom left of the screen), it simply goes back to the PHONE app page where I can't press on anything or do anything except swipe up to close the app.
Solved!
Go to Solution.

Did you reboot the device by removing the battery?
1. Please thank those who help you by clicking the "Like" button at the bottom of the post that helped you.
2. If your issue has been solved, please resolve it by marking the post "Solution?" which solved it for you!

Name does not show incoming calls, but only the number

Hi, i have a BB 9300 with OS6 brand wind italia. this is my problem:
-sometimes when my rubric contact call me i can't seeyour name, but only your telephone number. I noticed that is common when the phone is locked with password.
I called the support, but I have not receives assistance!
I also replaced the device, but the new one is equal.
Please help me!!!!
Sorry for my bad english

It sounds as though you have content protection enabled on your address book. To disable this feature in OS6, search for "Encryption" within Options. Uncheck the "Include contacts" box.

Verizon iPhone 4S 16GB does not receive incoming calls

Hi all,
In December, I bought my first iPhone, and I absolutely love it. However, recently I've had (what I consider) a big issue. I am self-employed, and rely on this phone to make money from customers calling me inquiring about items I have in my store, or items they will pay a finders fee to locate.
In the past week, I've had two people say they cannot get in touch with me. One, a customer, and the other, my mother, who is in the hospital. Both say they tried multiple times, and the phone would just keep ringing, and would never get to voicemail. I looked at my missed calls, and I had no notifications of a missed call, nor any that showed up in my log. Both have confirmed they called my exact cell #. What gives? Has anyone else had this issue? I'd take it to Verizon (or would an Apple store be better?) but since this is an isolated event, I doubt it would "reveal itsellf" when the issue will attempt to be replicated in-store.
Could anyone give me some guidance or advice on what would be ideal to do with an issue such as this?

Check the Call Forwarding section. There are two options to select. One says Forward All Calls and the other says Forward Unanswered Calls. Make sure Forward All Calls is not selected. That would cause all calls to go to the number specified which may be your voicemail. To get there from the home screen click the Phone icon > push the option button (left of the trackball) > click options > click Call Forwarding.

Caller ID does not work when calling from Jabber

We have the following results when doing calls within the company:
Desk Phone A (4567-X-Smith): 7801234567
Desk Phone B (4568-Y-Miller): 7801234568
Main Company Line: 7801230000
All desk phones have the following type of configuration:
Under the phone -> Line[1] -> Line1 on Device <MAC>
Display (Internal Caller ID): 4567-X-Smith
ASCII Display (Internal Caller ID): Our Company Name
Line Text Label: 780-123-4567
ASCII Line Text Label: 780-123-4567
External Phone Number Mask: 7801230000
Desk Phone A calls Desk Phone B
- caller ID shows up properly on Desk Phone B as 4567-X-Smith
User at Desk Phone A makes the call through the Jabber client to Desk Phone B
- caller ID shows up as 7801230000
This last situation is the problem since we want all internal calls whether they're form the desk phone or Jabber to show the proper caller ID. However, we want the generic main company line (7801230000) to show up to anybody outside the company. What is set incorrectly? Why does Jabber take over the line but not keep the same caller ID settings? Does jabber work as if it's doing an external call?
Thanks in advance,
Kris

Interesting... I just 4-digit dialed 8182 (typed in the Search field at the top of the jabber window) and my proper caller ID showed up...
Next I tried 10 digit dial 7804988182 through jabber and it showed 7804988100 (our external calling mask). I also just noiced that it very briefly flashes 97804988182 so that seems to indicate it's trying to dial through the PSTN...
Oddly enough, if I 10 digit dial through my desk phone, it shows the proper caller ID.

HT204387 My Iphone 4S will not allow me to answer incoming calls on any bluetooth headset without selecting it from the audio source menu.

My Iphone 4S will not allow me to answer incoming calls on any bluetooth headset without selecting it from the audio source menu.The connection works because once I do select the device...I can hear and speak. Any ideas?

Thank you templeton peck, I just rang them, turns out my contract doesn't allow it!

UNABLE TO SEE/ANSWER INCOMING CALLS. Instead, there is a "call status" button in lower left hand corner of screen...

UNABLE TO SEE/ANSWER INCOMING CALLS. Instead, when there is an incoming call, there is a "call status" button in lower left hand corner of screen...if i try to select the "call status" button, it does not do anything. Is this a reception issue? Very strange.....please help!!!!
Post relates to: Treo Pro T850 (Sprint)

yeah, that's pretty strange. i suggest to try soft reset first and then if it's still showing the same behavior. do a hard reset. that should help. however if it's still acting strange, you call the palm tech support hotline. 1-877-426-3777. they will help you with your sprint treo pro.

[svn] 3045: Fix FB-13900: Expression Evaluator: 'is' and 'as' expressions return 'Target player does not support function calls'

Revision: 3045
Author: [email protected]
Date: 2008-08-29 10:59:25 -0700 (Fri, 29 Aug 2008)
Log Message:
Fix FB-13900: Expression Evaluator: 'is' and 'as' expressions return 'Target player does not support function calls'
Ticket Links:
http://bugs.adobe.com/jira/browse/FB-13900
Modified Paths:
flex/sdk/trunk/modules/debugger/src/java/flash/tools/debugger/concrete/BinaryOp.java
flex/sdk/trunk/modules/debugger/src/java/flash/tools/debugger/concrete/PlayerSession.java

Revision: 3045
Author: [email protected]
Date: 2008-08-29 10:59:25 -0700 (Fri, 29 Aug 2008)
Log Message:
Fix FB-13900: Expression Evaluator: 'is' and 'as' expressions return 'Target player does not support function calls'
Ticket Links:
http://bugs.adobe.com/jira/browse/FB-13900
Modified Paths:
flex/sdk/trunk/modules/debugger/src/java/flash/tools/debugger/concrete/BinaryOp.java
flex/sdk/trunk/modules/debugger/src/java/flash/tools/debugger/concrete/PlayerSession.java

TS3276 My o2 email account does not work when sending from my MAC it will accept incoming mail but not send it gives me a message that o2 account (offline) my mac I have no problem with my iPhone or mac laptop. any suggestions please.

My o2 email account does not work when sending from my MAC it will accept incoming mail but not send it gives me a message that o2 account (offline) my mac I have no problem with my iPhone or mac laptop. any suggestions please.

Sorry for the delay...
I did what you've told me, new account and manually copied my files from Time Machine. I had lots of permissions problems, but at the end, almost everything is in order... It seems it had to be with some of the Apple Preferences, but I can't be sure, as most of them were dumped to the trash can.
I still don't have my Mail Rules back, unfortunately, although I did goggled some. It is a pity, as I had around 30 or 40 of them, getting my mail in order to each of its mailboxes, but it is a small price as the rest doesn't show the before syntoms.
Thanks for the help, anyway!!

Phone does not ring when called any suggestions

Iphone4 does not ring when called. Any suggestions?

Is the silent switch on?
Does the ringer not sound or does the call not come through at all?
Can you make outgoing calls?

2811(NM-8AM) does not answers incoming call from PC

Similar Messages

Maybe you are looking for