2960S-48FPS-L15.2.2E upgrade went sideways -- sched-7-watch

I attempted to upgrade single switch using the archive-sw /overwrite command. The new firmware appears to have installed and there is room on the flash.
However when it boots it doesn't "see" any of the interfaces or the config. I get the following error:
Switch#sh run
Unable to get configuration. Try again later.
Locked by -1
Unable to get configuration. Try again later.
Locked by -1
Switch#
Mar 30 01:29:45.842: %SCHED-7-WATCH: Attempt to lock uninitialized watched semaphore (address 0). -Process= "Exec", ipl= 0, pid= 3
-Traceback= 46CBC0z 17F77D0z 4781E4z 478338z 47B9C4z 47BA54z 41B454z 3B54C0z 3BB844z 3CB5ACz 214E980z 214AD00z
I cannot save any configuration, nor are there interfaces. It gives me an "invalid command" error when I try dir flash:. I can see it initialize flash during boot.
Anyone have any ideas how to fix this?

The license file might be missing. I can't tell if it's missing or if the system can't read it -- like how it can't read the config.text file.

Similar Messages

Have Macbook Pro & 4th gen iPod Touch. Downloaded & installed iOS 4.3.2 yesterday. Upgrade went without a hitch, but now iTunes on My Macbook Pro will not open. I get an error that says "iTunes" Data too new to be used with this version of iTunes.

Have a Macbook Pro and a 4th gen iPod Touch. Downloaded and install iOS 4.3.2 yesterday. Upgrade went without a hitch, but now iTunes on My Macbook Pro will not open. I get an error that says --The file "iTunes Library" cannot be read because it was created by a newer version of iTunes--. I am running iTunes 10.1. I searched for Updates to my MacBook Pro (running 10.6.7), but comes back saying no updates available. WHAT IS GOING ON??

Is your computer still authorized in the Store menu in iTunes?
iTunes Store: About authorization and deauthorization
When I changed to my new MacBookPro I had to authorize it although I used TimeMachine to transfer my settings and data.
Did you try to deselect Wi-Fi syncing and enable it again after that?
iTunes 10.5 and later: Troubleshooting iTunes Wi-Fi syncing
Did you already transfer your purchases and manually started a backup?

ML upgrade went smooth but I can't access icloud document library from pages or any other app?

The upgrade went OK but I can't access the icloud document library as described in the Apple features section. I can't get the dialog option in either Pages or Numbers Open boxes and it is not an option in Finder either.

1. Switch to Finder bt clicking on your desktop
2. On the Menu bar is the Go menu
3. Click on it holding down the option key and you should see the system library listed (exact wording escapes me I am not in Lion)
Peter

I downloaded ios 6 for my iPad 2 and some of the upgrades went through but not all. It sounds like I need to reinstall ios 6. How do you do that? Everytime I try to upgrade it says I'm already updated

I downloaded ios 6 for my iPad 2 and some of the upgrades went through but not all. It sounds like I need to reinstall ios 6. How do you do that? Everytime I try to upgrade it says I'm already updated

If you mean Siri then that is only on the iPad 3, it is not on the iPad 2 in iOS 6 (possibly because the iPad 2 doesn't have the Audience chip which the iPad 3 does). If there are other things that you think are missing (YouTube has been removed, and Passbooks is iPhone and iPod Touch only) ?

Catalyst 4900M and Catalyst 2960S-48FPS-L interconnection

I have Catalyst 4900M as distribution level and several Catalyst 2960S-48FPS-L as access devices.
I am going to use "WS-X4908-10GE 8 Port 10 Gigabit Module Switch"
With CVR-X2-SFP10G converter module I can get 10Gig on optical ports from Catalyst 4900M side, but Catalyst 2960S-48FPS-L support only 1 Gig optical standard on their SFP ports. Will it work (optical 10Gig<->1Gig) or any other suggestions?

You've got an X2 port, don't you? If you do, then why don't you purchase a TwinGig converter.
The Cisco TwinGig Converter Module (below) converts a single 10 Gigabit Ethernet X2 interface into two Gigabit Ethernet port slots that can be populated with SFP optics, enabling customers to use Gigabit Ethernet SFPs on the same card in combination with 10 Gigabit Ethernet X2 optics.

I just upgraded to FF 4.o, had 3.X running just fine, the upgrade went fine, but now it won't open Firefox at all.

I just upgraded to FF 4.o, had 3.X running just fine, Windows 7, the upgrade went fine, but now it won't open Firefox at all, it just loads and sits there and stops, but my task manager shows FF running in the background, I have tried reinstalling twice, no change, what is causing this?
Processes is the only place it shows Firefox running, programs won't show it in Task Manager.

Reinstall 10.6 again, but this time hold c boot off the 10.6 and erase the ENTIRE internal drive.
You do this by selecting the drive makers name and size on the left hand side, not the slightly indented partition underneath it.
If you erase and install 10.6 only into a parittion, say Macintosh HD, the you still have the hidden Lion Recovery Partition on the drive and it appears you already have 10.7
In the MAS, hold option and click Purchases to redownload Lion
FYI, you don't need to install 10.6 to reinstall 10.7, 10.7 can be reinstalled via the Lion Recovery, Command r boot.
See this for more info
https://discussions.apple.com/docs/DOC-3046

Upgrade went perfectly

Hi all,
I recently posted that I was not willing to upgrade to iTunes 5 because I was afraid to due to all the issues I have read on this and other boards. Well, I could not resist long, so today I upgraded. It went perfectly. Maybe it is because I was upgradign from 4.9, but the entire upgrade was fine, and my iPod snynched with not problems. I really don't see a whole lot of difference in 4.9 and 5.0 though. I suppose now I need Outlook 2003 in order to sync that? At least I have read that somewhere. Good luck to everyone on the upgrade.
Joey

go to an apple store hopefully you have one near by

Upgrade went well

After the horror stories I read on this forum, I'm pleased to report that my upgrade to iWeb '08 went beautifully. My site is intact, all the menus and links work. Hooray!
Thanks to everyone who let me know what to back up before installing the upgrade. It was great to know I had a safety net!

Thanks for the post!
-Mark

DIY hard drive upgrade gone sideways...

I just completed an upgrade of the hard drive in my 20" iMac G5 (no iSight). After filling it chock full of picture and movies, I installed a WD 750GB drive to replace the original WD 250GB. I followed the Apple DIY guide, and for the most part it went smoothly.
Except, that is, on step 4, page 7 of the guide. During that step, it is necessary to remove the hard drive thermal sensor cable from the hard drive mounting, leaving it attached to the system board. I did that, and the jack at the end of the cable came apart...it just crumbled. I was able to reseat the cable ends into what was left of the jack, get it reattached and complete the upgrade. My upgrade to 10.5 also went smoothly. But I know that the cable is not all Kosher in there, and I want to get a new one in ASAP. The part number is 593-0151-A and there is also a "K 1705 1" printed on the part label.
I've heard that this is not an uncommon occurrence, but it leaves me searching the web for a replacement. I can't find one anywhere except in the UK. I'm just not willing to send the unit into Apple for a $3 part. Any suggestions for a US-based supplier of Apple parts?
Message was edited by: pjmama

Welcome to Discussions - try [here|http://www.welovemacs.com/aphadidrac.html] or [here|http://www.partstore.com/sl/1/indexd123.html].

Android 5 upgrade went smoothly

Last saterday I got the message that version 5.0.2 was ready to be installed. I used Sony PC Companion, followed exactly what was listed on the screen and started the upgrade.Within 30 minutes I had a proper working Android version 5.0.2 with all the personal settings intact. Now, some days later, I haven't noticed anything which is not ok. Perfect job Sony !!

The wording is confusing? Between all the negative posts about Sony I wanted to tell the opposite.The upgrade is done as described and went 99,999% OK. So it is not all drama !!

3.1 Upgrade went Smoothly

This has to be the smoothest upgrade to date for me thanks guys!

I tried to upgrade from 3.0 to 3.1. The upgrade (apexins.sql) went fine. With the post-install tasks I ran into problems. when running apxldimg.sql I got the following error/ Any thoughts?
Regards, Eric
SQL> @apxldimg.sql d:\apex
PL/SQL procedure successfully completed.
old 1: create directory APEX_IMAGES as '&1/apex/images'
new 1: create directory APEX_IMAGES as 'd:\apex/apex/images'
Directory created.
declare
ERROR at line 1:
ORA-22288: file or LOB operation FILEOPEN failed
The system cannot find the path specified.
ORA-06512: at "SYS.XMLTYPE", line 296
ORA-06512: at line 15
PL/SQL procedure successfully completed.
Commit complete.
timing for: Load Images
Elapsed: 00:00:00.15
Directory dropped.
SQL>

Leopard to Snow Leopard upgrade went flawless

Probably 95% of the topics here are problems and horror stories. So here's one from the good side:
Upgrading from Leopard 10.5.8 to SL 10.6.2 was relatively painless. The whole thing took about 2 hours on my 2.16Ghz iMac. I took the standard precautions... backup and repair permissions, install, repair permissions, System Update, repair permissions again.
So far, everything is working fine. I've tested Pages '09, Numbers '09, Word and Excel 2008, Photoshop Elements 8, printing, scanning, and faxing through the Officejet 6500, and reinstalled Cisco 4.9.01.0180.
Now I'm going to upgrade my 13" Macbook.

You probably aren't going to be able to use your Snow Leopard Discs in your MacBook as they were for a MacBook Pro, and they made these discs where they aren't able to be used in other computers. You can try it, but I'm pretty sure it isn't going to work. If it doesn't work, then call Apple and order a set of discs for the computer to upgrade to Snow Leopard. They will sell it to you for $19.99 but if you want to try it, it wouldn't hurt.
As far as getting two partitions into one, when you get into the setup wizard, you can click on the menu in the corner, go to Disk Utilities, and you can delete both of the partitions and then create one large one.

So my upgrade went through, but my speed is the sa...

I'm around 250m from a small FTTC cabinet. On 40/10 I was on the full 38.72 profile for download for the past 6 months straight, and the full 10000 upload. My Huawei modem suggests that my max attainable rate is around 67Mbps, and my max upload is around 22Mbps. And the BT speed checker estimated my new speed at around 60Mbps. This led me to believe that upgrading was a good idea.
This morning I discovered that my downstream profile is still 38.72Mbps, but my upstream profile has jumped to 20,000. So the upgrade has gone through, but my downstream profile hasn't changed at all.
Is it worth performing a modem reset? My modem has been on for 6 months without a reboot, so would it be worth resetting to see if that jogs the IP profile up on the downstream? Or is there anything else I should try?
Yesterday before the upgrade:
Now:

So put my order through yesterday, this is before;
This is after;
Bit lame
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
You can contact the forum mods here

My upgrade went wrong!!

HI!!
I wanted to upgrade my itunes from 6.0.2 to 6.0.4, so I did. But when it was downloaded, the old version was gone, and the new wouldn't open. What shall I do? Delete itunes and try to download it again? And my music are well gone anyway, ain't it??
Windows XP

hiya!
the new wouldn't open.
a few questions before proceeding.
are you getting an error message? if so, what does it say? include error message numbers if you're getting any.
or are you getting no error messages whatsoever when you try to launch itunes?
if you're getting no error messages whatsoever, do you just see the wee hourglass for a few seconds, and then nothing? if so, do you also have Norton Internet Security 2005 installed on that PC?
or are you seeing a brief "flash" of the itunes license screen (and then nothing)? if so, do you also see similar behavior when you try to launch your QuickTime?
love, b

2960S-48FPS-L as unknown in DFM 3.1

Hi
I am facinf issue with LMS DFM module where i can't see the particulat model switch and it seems unknown
What can b the issue.
Any point to strat the dgnosis is appreciated.

You need to be in DFM 3.1.3 at least, have Device Updates 5.0 and device should be running 12.2(50)SE or higher. You can download the DFM device packages from this link. This information can be acquired using this link.

2960S-48FPS-L15.2.2E upgrade went sideways -- sched-7-watch

Similar Messages

Maybe you are looking for