300x AIR-CAP702W - how to manage config/templates

I have a new installation of a WLC 8510 running 8.0.110
Now we need to deploy 300x AIR-CAP702W that has 4 ethernet ports
We need special config for each of the ports - is there a way to template the install so we don't have to change each AP individually?
let's say we need to change vlan assignment on one port over the 300 AP's
I don't see this in the WLC - and not able to find the relevant info
- Benedikt

To be able to make a bulk change like that you would either want to use PI and push a template down to the AP.
Or
You can use CLI commands. For the CLI you need the AP names but you can cut and paste the commands from an excel doc into the CLI.
You can get the command structure for the CLI from the Configuration Guide here:
http://www.cisco.com/c/en/us/td/docs/wireless/controller/8-0/configuration-guide/b_cg80/b_cg80_chapter_010011101.html#task_E46F0CE53E7D465C879F388C63243406
HTH,
Steve

Similar Messages

AIR-CAP702W local ethernet ports

Hi all,
The new AIR-CAP702W AP have 4 10/100/1000Base-T local Ethernet ports.
On the data-sheet it's written "for wired devices connectivity".
http://www.cisco.com/c/en/us/products/collateral/wireless/aironet-700-series/data_sheet_c78-728968.html
That's very good, but how do we manage the traffic on these ports?
Are we able to configure theses ports in access-mode with different VLAN-IDs?
So in that case the uplink of the AP should be in trunk-mode.
And where do we configure the ports of the AP, on the WLC?
Or is the traffic from the devices connected into these ports encapsulated into CAPWAP tunnel, like the wireless data traffic, and is terminated into the WLC(s)?
In that case, can we choose what port is associated to what VLAN/SSID on the WLC?
Or something else maybe?
Thank you for your help.
Jerome

The 4 x 10/100/1000BASE-T local Ethernet ports support half and full duplex mode, auto-negotiation, and MDI/MDIX Auto-Sensing. Devices you connect must support auto negotiation if you connect with another mode, say hard configured speed and so on. The port may not be enabled and depending on the version of code, for example 7.6.100.120 the initial release, the ports are not managed.
For now, (until more control is added in the software) all the LAN ports are locally switched, are mapped to the 702W VLAN, and do not appear on the Wireless LAN Controller or AP.
Initially, the ports are disabled and may be enabled manually via CLI.
This was done to minimize any security risks. Here are the CLI commands to enable the ports.
(Cisco Controller)> config ap lan <port id> <enable/disable> <AP-NAME>
(Cisco Controller)> show ap lan <port id> <AP-NAME>
(Cisco Controller)> show ap lan port-summary <AP-NAME>
Hope that helps.

How do you delete templates in Pages?

How do you delete templates in Pages?

Hi Lilly,
If you mean "My Templates" they are in a hidden folder.
In Finder, open the Go menu and hold down the option key (alt) in order to see the user library folder.
Open the library folder and navigate to:
Library/Application Support/iWork/Pages/Templates/My Templates.
Select a template then drag it to the Trash (or command-delete).
Having gone to all that trouble to find that hidden folder, single click to select My Templates folder, then
Menu > File > Make Alias
An Alias folder appears. Rename it to something such as "My Templates Pages alias" then drag it out of My Templates folder to somewhere convenient (maybe the Desktop will do for now).
You can now close all those folders that you navigated through because the Alias (double click on it) is a quick way to go there again.
Repeat this process for other iWork apps such as Numbers.
Another way to manage your templates is to open one, make changes, then Save As Template with the original name of that template. The new template will replace the old one.
Regards,
Ian.

How to manage Rescue and Recovery Backups

Hi I've been using disk image backup solutions since the days of powerquests Drive Image. And have had my days with Ghost and Acronis Trueimage. I recently built a clean Vista image on my T400, and I'd like to take advantage of the Lenovo Rescue and Recovery 4.21 tool since it the recovery technology is already part of my system and I have tested it once.
I'm used to the idea that a backup tool will produce an image file, which I can manage myself, moving to various media....hiding under my bed etc. With RnR, I've noticed it prefers to control the directory's where backups are placed (this is a bit annoying to me, but I can live with it, as long as it's isolated to the RRBackup directory - which it appears may not be the case). I do appreciate it's ability to specify various backup media locations (network, CD, 2nd HDD, USB) and recognize that it's a simple approach for basic usage.
Recently I've backed up my image to USB drive, and also to the local disk. I'd like to take that back up and split it up into DVD's and burn it to disk. I know there is a built in RnR feature which lets us copy backups from the local drive (why only local drive ??) to USB/Network/CD, but unfortunately the CD copy feature burns directly to my thinkpad burner...which is a CDR device, not a DVDR device. I'd like to use the DVDR device on my desktop...
Anyway, I'd like to know if there is more resources on how to manage RnR Backups. I found the following guide http://www-307.ibm.com/pc/support/site.wss/MIGR-70344.html (which is hard to get on Lenovo's site...google finds it better), I'm still reading it, but so far it appears more focused on the pre-desktop area than backup management.
Any insight would be appreciated.
Thanks!

Hi Danielle,
Consider this allegory; factory settings will make your thinkpad like a never driven 0 meter car [with reference to software]. Hence it will be far-flung from it's previous state. Apart from what you have already saved on memory stick, all settings and the software you have installed on the notebook will be lost.
I hope this helps.
Maliha (I don't work for lenovo)
ThinkPads:- T400[Win 7], T60[Win 7], IBM 240[Win XP]
IdeaPad: U350
Apple:- Macbook Air [Snow Leopard]
Did someone help you today? Compliment them with a Kudos!
Was your question answered today? Mark it as an Accepted Solution!
Lenovo Deutsche Community Lenovo Comunidad en Español
Visit my YouTube Channel

How can i config WLS7 and iPlanet LDAP

How can i config WLS7 and iPlanet LDAP?
failed during initialization. Exception:java.lang.SecurityException: Authenticat
ion for user weblogic denied
java.lang.SecurityException: Authentication for user weblogic denied
at weblogic.security.service.SecurityServiceManager.doBootAuthorization(
SecurityServiceManager.java:978)
at weblogic.security.service.SecurityServiceManager.initialize(SecurityS
erviceManager.java:1116)
at weblogic.t3.srvr.T3Srvr.initialize1(T3Srvr.java:703)
at weblogic.t3.srvr.T3Srvr.initialize(T3Srvr.java:588)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:276)
at weblogic.Server.main(Server.java:31)
>

Yos:
Series of steps to get WLS working with some external LDAP server follows:
I. create a new domain /mydomain
II. start server
III. open WebLogic console in a browser
IV. in left frame, go to
security->realms->myrealm->providers->AuthenticationProviders and click
V. in right frame, click on “Configure a new iPlanet Authenticator”
VI. In the new screen, under General, make sure the Control Flag is set to Required,
select a name for this authenticator, and click Create.
VII. Select iPlanet LDAP tab and fill in values for Host, Port, Principal where
these values reflect the settings for your LDAP server. (Note: the default
principal for an iPlanet LDAP server is uid=admin, ou=Administrators,
ou=TopologyManagement, o=NetscapeRoot). Click Apply.
VIII. Click on Credential: Change. At the new screen, enter the credential
associated with the Principal that you entered in step VII in both boxes. This will
be the password that is used to do a bind to your LDAP server with the principal.
Click Apply.
IX. Select Users tab and make sure these properties accurately reflect the structure
of your LDAP server. Most of the time the only property that needs to be changed is
the User Base DN property, from ou=people,o=example.com to
ou=people,o=myCompany.com. Click Apply.
X. Select Groups tab and make sure these properties accurately reflect the structure
of your LDAP server. Most of the time the only property that needs to be changed is
the Groups Base DN property, from ou=people,o=example.com to
ou=groups,o=myCompany.com. Click Apply.
XI. Now, the boot identity of your server absolutely must be a user that exists on
your LDAP server. You must also have an “Administrators” group on your LDAP server,
and the boot identity must be a user that exists in this “Administrators” group, or
the server will not start. So open your LDAP console (this will be a console that
is specific to the LDAP server you are using) and use the management tools to create
the “Administrators” group and a user that you place in the “Administrators” group
that is the boot identity that you use to start WebLogic.
XII. Make these changes and restart the server.
XIII. You can verify that the LDAP setup is correct by doing a thread dump. You
should see a thread like:
“LDAPConnThread localhost:389" daemon prio=5 tid=0x8d9b308 nid=0x8f8 runnable
[0x9e2f000..0x9e2fdbc]
at java.net.SocketInputStream.socketRead(Native Method)
at java.net.SocketInputStream.read(SocketInputStream.java:86)
at java.io.BufferedInputStream.fill(BufferedInputStream.java:186)
at java.io.BufferedInputStream.read(BufferedInputStream.java:204)
- locked <3281d98> (a java.io.BufferedInputStream)
at netscape.ldap.ber.stream.BERElement.getElement(BERElement.java:101)
at netscape.ldap.LDAPConnThread.run(LDAPConnThread.java:420)
where “localhost:389” is the server name and port of your LDAP
server. This means that your Authenticator has been set up correctly.
XIV. Now you can delete your default authenticator. Open the WebLogic console and
go to security->realms->myrealm->providers->AuthenticationProviders in the left
frame, and click
XV. In the right frame, look for DefaultAuthenticator and click on the trash can to
the far right. Say “Yes” when it asks if you are sure, then click Continue.
XVI. Restart the WebLogic server. If the server boots correctly, you’re done.
Everything is working correctly.
Please note that the "default authenticator" refers to the embedded LDAP server that
ships with WebLogic.
Hope this helps.
Joe Jerry
Yos wrote:
How can i config WLS7 and iPlanet LDAP?
failed during initialization. Exception:java.lang.SecurityException: Authenticat
ion for user weblogic denied
java.lang.SecurityException: Authentication for user weblogic denied
at weblogic.security.service.SecurityServiceManager.doBootAuthorization(
SecurityServiceManager.java:978)
at weblogic.security.service.SecurityServiceManager.initialize(SecurityS
erviceManager.java:1116)
at weblogic.t3.srvr.T3Srvr.initialize1(T3Srvr.java:703)
at weblogic.t3.srvr.T3Srvr.initialize(T3Srvr.java:588)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:276)
at weblogic.Server.main(Server.java:31)
>

How to Manage Several (But Similar) Masks on One Layer

Hello, in video tutorials i'd like to "sketch-motion" a red circle around relevant areas – several times in one video, around several areas in several sizes, sometimes elliptical and sometimes rounded rectangle. Sometimes i might want to show changes in position and dimensions of the circle. The video tutorial itself is one video layer including audio, already rendered before imported to AE.
I know how to create a "sketch-motion" effect with a (for instance elliptical) mask and the "Stroke" effect. Now this red circle has various keyframes:
- At least for "Start" of "Stroke" effect and ended "Opacity" of this circle
- sometimes more keyframes for position and transform
I wonder how to best create 6 or 10 such red circles within one video tutorial:
- Should i do everything with one single "Mask 1", with keyframes for several appearances in several areas and sizes or
- should i create a new mask for every circle that i want to show (sounds much preferable)?
I don't want to arrange again the keyframes for each new circle added (build-up time of Stroke effect, fade-out time). Is it possible to save a mask with all keyframes and import it at several points on the time line, with all keyframes intact? (Position and Size would still be adjusted, as well as length of visibility.)
I searched but didn't find a good solution how to manage a "master mask" or "mask template" or how to show that mask with the "Stroke" effect various times with always similar keyframes for "Start" and "Opacity". If you could hint me at how to manage that, that would be great.
Thanks!

Mylenium, thanks for a helpful hint!
I tried your suggestions and it seems that i have to save
- mask shape and
- Stroke effect settings incl. key frames
as separate things, if i want them in the effects panel.
When i set the Stroke effect to my preferred look (with custom colours, width, key frames for Start and Opacity) and save this as an effect, i cannot re-apply this to another mask with any of my custom settings still there. When i re-apply the saved custom Stroke effect, all settings like keyframes, custom colours and width are lost and it arrives with default settings and without any keyframes.
Maybe i do something very wrong here?
I wondered if i should save the mask with Stroke effect as an AE file and re-import it. But this mask can only be saved together with some footage and i don't see how to bring mask including Stroke effect into an existing composition and which of the File/Import ways to use.
Thanks again!

Errors defining the destination for SQLAssembler inside data-management-config.xml

Hello,
I am following the LCDS ES sample at
http://localhost:8700/samples/#sqlassembler
for defining a destination inside data-management-config.xml,
there you can define SQL
statements that can be referred to from MXML
I am having the following error:
'Error in SQL for 'fill' in destination 'sql-product'.
Matching pair of # tokens not found'
And the statement it is referring to, from within the
data-management-config.xml file is:
<name>getAllForServer</name>
<sql>SELECT * FROM MYTABLE
WHERE SERVER_ID = #SERVER_ID#
</sql>
I do not understand the # syntax, and how can it be used
universally? for example, setting the value of LIMIT, or variables
in WHERE statements

Thanks a bunch, that was it. Any ideas where I can find DTSs
or Schemas for the FDS config files?
-Robert

How to enable config torrent service IOMEGA NAS EZ Media & Backup Center LENOVOEMC

Here you are a tutorial how to enable stand alone torrent service on IOMEGA NAS EZ Media & Backup Center
How to enable config torrent service IOMEGA NAS EZ Media & Backup Center LENOVOEMC
any ask do not hesitate to contact to me. Thanks
Roger Biderbost

Great info again, Roger
serene
Community Advocate Program Manager
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

How to manage Struts web application unavailbility ?

Hello !
I have a web application (portal) based on Struts framework. And I am wondering how is the best way to manage the portal unavailbility (for maintenance reasons for example) ?
We can deploy a new web application/page saying that "the portal is unavailable for the moment" but it is a heavy solution and not proper for people that are currently using the portal. So not good.
Maybe I should check in the init Action of the portal in a database if the portal is available or not... but how to manage people who are currently logged in ? should I check this state in each action of the portal ? it is quite repetitive...
Do you have any idea ?
Thanks for advice.

The simplest, lowest impact, lowest risk solution would be to use a filter:
import java.io.*;
import javax.servlet.*;
import javax.servlet.http.*;
public class AvailabilityFilter
implements Filter
   // private member variables for connection url/user/pass or JNDI
   // resource name
   // private getters and setters
   public void init( FilterConfig config )
      // Read necessary filter init-params here, like connection parameters
      // or the JNDI resource name of a connection pool used to determine
      // availability.
   public void destroy( )
   public void doFilter( ServletRequest request, ServletResponse response, FilterChain filterChain )
      if( this.isAvailable( ) )
         filterChain.doFilter( request, response );
      else if( response instanceof HttpServletResponse )
         HttpServletResponse httpResponse = (HttpServletResponse)response;
         response.sendError( 503, "Application temporarily unavailable" );
      else
         response.getWriter( ).println( "Application temporarily unavailable" );
         response.getWriter( ).close( );
   private boolean isAvailable( )
      // Attempt to connection to the database and/or check availability status
      // Return true if available, false otherwise
}Now, as far as managing existing user sessions goes, you can also implement an HttpSessionListener to track sessions:
import java.util.*;
import javax.servlet.*;
import javax.servlet.http.*;
public class SessionTracker
implements HttpSessionListener
    private static Map activeSessions = new HashMap( );
    public void sessionCreated( HttpSessionEvent event )
        HttpSession session = event.getSession( );
        synchronized( activeSessions )
           activeSessions.put( session.getId( ), session );
    public void sessionDestroyed( HttpSessionEvent event )
        HttpSession session = event.getSession( );
        synchronized( activeSessions )
           activeSessions.remove( session.getId( ) );
    public static void closeAllSessions( )
        synchronized( activeSessions )
            for( Iterator i = activeSessions.entrySet( ).iterator( ); i.hasNext( ); )
                Map.Entry entry = (Map.Entry)i.next( );
                String sessionId = (String)entry.getKey( );
                HttpSession session = (HttpSession)entry.getValue( );
                session.invalidate( );
                i.remove( );
}Some user event could call a servlet which would set a flag in the DB marking it as down for maintenance and then call the static method SessionTracker.closeAllSessions( ), which effectively logs everyone out. Any attempts to access the app after that period would fail; the filter would try to connect and/or check the flag in the DB and would throw an HTTP 503 instead of executing the rest of the filter chain. No reconfiguration would ever be necessary, and you wouldn't be changing code, just adding these two new classes and a couple of entries in web.xml.
Hope that helps,
- Jesse

How to Manage the Resource Master in Primavera Enterprise Version

We are using P6 enterprise version in our company having a central database. We had created our own unique resources and standardised across the enterprise and is Admin protected. However we often have to import some schedules sent by our consultant/client. In those schedules they have their own resources.
So when we import these schedules, it also imports the resources along with it and pollutes our resource master.
Can anyone let me know, how to manage such a situation.
Regards

We have met this issue. You have few ways to deal with it, but each has its own +ve and -ve.
1- You may create a separate "Working" db into which you can import those files and keep them there only. Your master db shall be used for maters and your own program only.
2- You may do the same for checking the resourses, vet them before importing into the final db
3- P3 and MSP importation allows you to select the node to which the resources will be located. We have created a resource node called "Imported Resources" and dumped all those resources into it. Our users don't have access to that node so those resources can only be used on the imported program and can't be assigned to any other program / activity
4- Enforce your supply chain to use the same resource list. We managed to do that for our main and subcontractors. That formed part of their contracts.

How I Managed to Install Windows 8.1 Pro on an iMac 27-inch, Late 2013

As is typical with many of my Boot Camp installs, this one did *not* goes as smoothly as planned. This installation was particularly troublesome, so I thought I would share how I managed to set up Boot Camp on a brand new iMac (27-inch, Late 2013) using a Windows 8.1 Pro DVD and an external Apple SuperDrive. These are the steps I took:
Download Boot Camp Support Software 5.1.5640 (http://support.apple.com/kb/DL1721)
Copy Boot Camp Support Software to empty MS-DOS (FAT)-formatted USB key
Run Boot Camp Assistant and select third option only (Install Windows 7 or later version)
Computer would reboot after Boot Camp Assistant finished but would boot back into Mac environment and not continue Windows installation
Boot computer holding down option key and select Windows (with DVD icon) and go through initial setup process (could go as far as trying to format Boot Camp partition as NTFS and then got stuck)
Quit Windows installer and reboot computer holding down option key and select EFI Boot
Run Windows installer
These same steps worked for another iMac (same model) that I set up later the same day.

Note: These types of discs or activities are not supported by DVD or CD sharing:
DVD movies.
Audio CDs.
Copy protected discs such as game discs.
Install discs for an operating system such as Microsoft Windows (for use with Boot Camp), or Mac OS X.
Burn a CD or DVD

How to migrate rtf Templates in XML Publisher ?

Hi All,
I want the script so that i can download and upload the RTF files directly from my development instance to my production instance.
For this i have come across 3 links
How to migrate rtf Templates in XML Publisher?
http://download.oracle.com/docs/cd/B40089_10/current/acrobat/120xdoig.pdf
unable to migrate physical files using XDO Loader utility
and from here i am running this command from /home/aryan directory
java oracle.apps.xdo.oa.util.XDOLoader DOWNLOAD -DB_USERNAME apps -DB_PASSWORD fnd -JDBC_CONNECTION sharp.apps.com:1522:tst1 -LOB_TYPE TEMPLATE -APPS_SHORT_NAME CUSTOM -LOB_CODE ZEMP -LANGUAGE en -TERRITORY US
but it is giving me error "ksh: java: not found". could anyone can tell me how and from where i have to run the download and upload command
Thanks
Aryan

Hi Hussein,
I tried with applmgr also and still for java -version it is giving me error ksh Java not found
and for which java it is giving me error no java found in different directories path.
Thanks
Aryan

Questions on JMX and management-config

I was wondering if anyone can clarify the usage of management-config.
We've got a setup with managed-nodes=all and allow-remote-management=true (other params defaulted). We've got processes that occasionally ping the cluster (via a single node) to log performance statistics and to look for problems that might require intervention (across all nodes via remote management).
I'm trying to determine if the JMX subsystem is completely isolated from runtime cache performance.
1) Does the setting for the read-only flag impact performance in any way? If set to false, is there any sort of locking or synchronization that takes place when querying cluster nodes?
2) Do calls to JMX (and presumably the Invocation Service) share any resources with a Distributed Cache Service?
3) the Default management-config settings in Tangosol-coherence.xml point to the "Management" service - which is not actually defined elsewhere in the configuration file. Is this actually an implicit link to the Invocation Service?
4) Is there a single "Service Thread"? or does each distinct service have its own service thread?
Thanks in advance,
Dave

The performance impact of management is relatively small. The consumption is based on the information "read" (getAttribute/getAttribute) and the frequency of the poll. Polls of the same data element within 1 second will receive the same result for remote nodes.
The formula to determine the network consumption estimation formula for Coherence 3.3 on a single poll of the information is:
Estimated network bytes per poll =
Number of remote Node MBeans retrieved * 725
+ Number of remote Cache MBeans retrieved * 225
+ Number of remote Storage Manager MBeans Retrieved * 720
+ Number of remote Service MBeans Retrieved * 144
+ Number of remote Point to Point MBeans * (Number of Nodes in Grid -1 * 250)
Given the order N size of the Point-to-Point MBeans, It is not recommended to put that information in a loop for a large cluster.
1) Does the setting for the read-only flag impact performance in any way? If set to false, is there any sort of locking or synchronization that takes place when querying cluster nodes?
EW: The Read-only flag does not impact performance. There is no synchronization on read of the objects. Synchronization on update is on an attribute by attribute basis.
2) Do calls to JMX (and presumably the Invocation Service) share any resources with a Distributed Cache Service?
EW: The JMX calls are processed through the Management (Invocation) Service. This shares system (memory, CPU, network) resources with other services. The management information is not processed out-of-band and under extreme load performance will be impacted.
3) the Default management-config settings in Tangosol-coherence.xml point to the "Management" service - which is not actually defined elsewhere in the configuration file. Is this actually an implicit link to the Invocation Service?
EW: The Management service is a non-configurable Invocation service.
4) Is there a single "Service Thread"? or does each distinct service have its own service thread?
EW : Not exactly sure I understand the question. Each service has its' own "Service" thread and thread pool. However, there are some shared components at the TCMP (network) layer.
Hope this helps,
Everett Williams
Message was edited by:
user631017
Message was edited by:
user631017

How to create matrix template help pls

hi frs,
i have generated xml file after creating matrix report in report builder.
i want to know how to create matrix template(rtf) in word document.
if i use wizard or insert> all fields i am not getting rtf like matrix.
help pls
Thanks
Rajesh

This issue is really becoming a problem for us. Does anyone have any examples of label templates. The label when generated automatically converts from pontrait to landscape. If you increase the size of the template then word complains about the page and margin size before printing.
Anyone have any ideas?
Thanks

My neighbour's Mac Book Pro shows up as discoverable when Bluetooth is turned on in my iPad Air. How can I block her device? How can I prevent her pairing with my iPad Air. I need Bluetooth on to play music over my system.

My neighbour's Mac Book Pro shows up as discoverable in my Bluetooth list on my iPad Air. How can I block her Bluetooth device? How can I prevent her pairing with my device? I need Bluetooth to stream music on my Bose system. Thanks!

If your device is discoverable, the other BT device would try (I am not sure if that would be successful). If it was, it would appear in your system preferences>Bluetooth.
Take a look at this re: security:
http://support.apple.com/kb/PH10786
This is from another Apple article:
Use Bluetooth
You can wirelessly transfer files between computers—even Mac to PC—using the Bluetooth File Exchange utility. You can even browse selected devices and retrieve files remotely. For extra security, you can stipulate that only trusted devices be allowed to connect to your Mac, and 128-bit over-the-air encryption is also available
Barry
P.S. Since I have not had the issue, I have not researched this before. Thank you for making me look into BT security
Message was edited by: Barry Hemphill

300x AIR-CAP702W - how to manage config/templates

Similar Messages

Maybe you are looking for