645e max 2, no post & d-bracket shows 1-4 as green

i'm not feeling very well and ive tried searching this forum for an answer to whether its the mobo at fault or the cpu... ive tried various power units, AGP cards, various RAM configurations... nothing changes. it crunches a couple of times after the power comes on, all fans fire up, they continue to spin and everything has hung- nothing on the monitor at any point. the front panel doesnt respond either. the d-bracket shows 1-4 in green from when the power is turned on at the front panel and remain indefinitely.
ive tried clearing the cmos by jumper and by battery many times.
when this computer used to work, it belonged to my nomad of a friend who took it from place to place and i fear something got damaged in transit.
can someone tell me what the most likely cause is? i'm at my wits end.
thankyou

It should be minimum 18amps. 20 would be good .Buy a good brand like Antec or Enermax.I think it will solve the problem .....but even if it doesnt i can safely say that a better psu will prevent any future problems and keep ur comp running smoothly

Similar Messages

PC Won't Post: D-Bracket Shows 4 Red Leds= CPU Damaged?

Hello all. New to these forums. I recently upgraded to an EpoX 8RDA+ and am trying to setup my KT4 Ultra for my g/f. After connecting/installing everything the computer won't post. Nada. The D-Bracket 2 shows the four leds red which means "The Processor is damaged or not installed properlly." I tried an Athlon XP 1600+ and 2000+ an neither worked. is going on? I'm going to remove the mobo now and put it in the case that my 8RDA+ is in. Any suggestions in the meantime would be appreciated.
System Specs:
MSI KT4 Ultra
Athlon XP 1600+ w/ Thermalright SK6+
512MB Kingston HyperX
420Watt Codegen PSU
30Gig WD Caviar

I have had problems like that a clople of times. Once the processor was dead on arrival and the other was when the fan was not enough for the processor.The system got stuck even before the screen appeared. In your case check if the fan is installed correctly.

I think I was cheated on the 645E Max-C

I was hoping someone could answer a question.
I just purchased a 645E Max-c (well thats what the box and all said). But when I inspected it further the motherboard had been restickered with the 645E Max-C sticker being placed over the actual board serial (which was a 645 ultra.
The only real difference between the two boards appears to be the chipsets. One of which (Northern) I can't check because it is under the heat sink. But should I assume that this chipset should have 645DX on it as opposed to the 645 that is installed in the ultra?
Secondly, on the second chipset (Southern), should it be marked as 961B and not the 961 as is in the ultra?
Could someone please advise me on this, so i can crack the shits with the supplier if he is wrong.
Regards
ACI

Quote
Originally posted by Bela
Quote
Originally posted by BiOsPhErE
Quote
Originally posted by BigConig
hmm- I've noticed a few weird things about my max-c also. If I use info-view, it shows the mainboard model as ms-6547 not MS-6547E (according to the website it should be the "E").
The same thing shows up if I use live update for the bios, MS-6547.
However, Sandra shows the chipset as 645dx and the bios shows ata133, which I don't believe was available with the 645 chipset.
from the looks of it, the max-c was a bit of a frankenstien board which has already been moved into the "archive" section in MSI's products.
Ms-6547 = Ultra
Ms-6547E= ???????????? ?( ?(
I dun think there's such mobo

Item Seller Type Unit Price iBlacklist - Block Unwanted Calls, v1.0 (4 ) Write a Review Report a Problem Max Kub App $4.99 but show other application"secret contact" on screen .can't block any contact

Item
Seller
Type
Unit Price iBlacklist - Block Unwanted Calls, v1.0 (4 ) Write a Review Report a Problem
Max Kub
App
$4.99
but show other application"secret contact" on screen .can't block any contact. so seems tyhat i order one aplication "iBlacklist - Block Unwanted Calls, v1.0 (4 )" but get another application "secret contact "as it appear on screen ????

Reply to n82phone:
what you are telling i think is too much. I've read your requests and believe me some of them is out of context. One example is listening to radio while being on a call. Who would like to have such options?? It's ridiculous.
But But it doesn't mean all of them are ridiculous! Just like the #1 concerning music, #4 concerning the camera and #5 concerning the volume, I strongly agree with you as it makes sense!
So if I was to write to nokia, which I will do in the coming days is to write them again:
Points #1,4,5,9,11,14,15,24! These are strong points!
People out there, if you want the changes I specified to be done by nokia, you should write them the same points. If only one or two write, it's useless, they won't take it as a priority.
Of course, don't copy paste or they will think the same person is spamming them. I hope it's clear. Write in your own words. Don't think changes will be done by magic or by doing nothing with arms folded. You should do a move.
THIS IS A USER TO USER FORUM. YOU CAN POST YOUR PROBLEM HERE. WE'LL DISCUSS ABOUT IT, THEN ALL OF US SHOULD WRITE NOKIA TO CORRECT THE MATTER IF IT CONCERNS FIRMWARE. FOLLOW THE LINK "CONTACT US > CALL OR EMAIL NOKIA CARE" TO REPORT THE PROBLEM TO NOKIA.
Thank you
Message Edited by fafanne on 18-Oct-2008 01:51 AM

Does 645E Max/Ulta has USB 2.0 ?

Hi, I just bought a 645E Max / Ultra MS-6547 Ver 2 MoBo.
It came with the Led D-Bracket. The reseller told me that it has USB 2.0 onboard. But the manual only mentions USB and is not specifiv on USB 1.1 or USB 2.0. Does this MoBo actually has USB 2.0 onboard? Thanks, Velti

On-Board Peripherals
On-Board Peripherals include:
- 1 floppy port supports 2 FDDs with 360K, 720K, 1.2M, 1.44M
and 2.88Mbytes.
- 2 serial ports (COM A + COM B).
- 1 parallel port supports SPP/EPP/ECP mode.
- 6 USB ports (USB 2.0 Controller by SiS®962L SB)
- 1 IrDA connector for SIR
- 1 audio/game port

645E max booting

Does anyone know what the beep patterns on the MSI 645E Max (MS-6547 v 2.X) are during boot up? They are not listed in the manual nor could I find it on the site.

I dont know the bbep codes but until someone posts them for you you could try the following...
Most common causes of beeps during bootup is 'ram not seated correctly, take out and reseat, and video card not seated properly, again take out and reseat'
Thats something that you could try before you get a better reply... sry if this proves to be no use.
PS: what beeps are you hearing?

645E Max Hard Drive problem

I have just purchased the 645E Max MS-6547 v.2.x board. It's got a SiS 961B chipset and is supposed to support P4 processors at 533MHz.
I have 3 Western Digital hard drives plus a cdrom plugged at the moment. I jumpered them as I always have...master/slave or, if alone on one ide, no jumper at all. They were detected correctly in the bios but I was unable to get into any OS. After the POST, I got a bunch of 9's or 1's on my screen and could go no farther. The only way I can boot into Win2K, WinMe or Win98SE is if they are jumpered as Cable Select. They run fine that way but I don't think Cable Select is supposed to be my only option here.
I have two HDD's on ide 1 The Prim/Master is 15GB, ata66 and Prim/Slave is 60GB, ata100 with the correct ribbon cable, and on ide 2, Sec/Master is 6GB ata33 and the cdrom as Sec/Slave.
I appear to have the most recent bios version 3.1 (I believe that's the version) and could find no updates that address this problem. LBA is enabled btw.
Has anyone else experienced this wierdity?
Also, is anyone running linux with this mobo?
Lucyjean

OK my computer is obviously up and running because I'm here :] Drives on both ide controllers are jumpered cable select. I have only one bootable drive and it's the primary master.
The drives weren't switched around.....I would have gotten some kind of system disk error message I think if that were the case and not a bunch of 1's and 9's on my screen. The boot order in my bios is ok too.
Not only do I have to use cable select on ide 1, I have to do it on ide 2 also or it will just hang after the POST.
My bootable drive is a western digital. Even as a standalone, I have to jumper it cable select or it hangs. After I got the computer to boot with just the one drive on ide 1, I added a hard drive to ide 2...another western digital, and couldn't get past the POST unless I used cable select on it too. Very strange indeed.
I'm not so sure about this motherboard......

Poor Performance with 645E Max v2.0

I have the following setup:
645E Max v2.0 mother board
1.7 Ghz Pentium 4
1 Gb RAM - Kingston 2100 - 2 * 512Mb
Leadtek A250 - Nvidia GeForce 4 TI 4400 with 128mb
SoundBlaster Audigy Gamer
All 4 USB ports are enabled
All Serial and Parallel ports are disabled
On board sound, midi and gameport disabled
AGP aperture set to 512MB
Creative Labs 32x CDROM
Western Digital 120GB IDE/EIDE Hard Drive
300w Power Supply
Mother board set to "default" settings - no overclocking
ViewSonic A90f monitor set to 1152x864 - 32bit color
DirextX 9 - Hardware acceleration for graphics and full-acceleration for sound
Every patch, update, version available for all software and hardware.
When I run 3DMark03 on this system I get a score below 500. When I do an online compare of similar systems (the mother boards are not the same but the sound, graphics and memory are the same) the scores are around 1500. When I look at the details my system is without exception running at a fraction of other systems in all respects.
Also, I am currently unable to play Train Simulator unless I really ease off on the graphics and sound.
Given my current hardware and expectations regarding performance should I be using a different MotherBoard? What about power supply?
I've talked to support engineers from Microsoft and Creative and they are of the opinion that my system should perform as good as any out there.
Any thoughts?

If it's not giving you errors, and is not unstable, I would (guess) not.
Did you load all the motherboard drivers and the SIS AGP driver? Just double checking.
Edited: Have you updated the BIOS on that (3.2 or above)? There's a BIOS available that turns on fast writes. That should make a difference.
Might also check this link to the first post in this forum. Not sure if all that applies to your board also. Doesn't sound good though.
http://www.msi.com.tw/program/e_service/forum/viewindex.php?threadid=5983&boardid=10&styleid=1&sid=f203fcc77a21fa64eba984872eb06a24

Msi k8n neo 4 wont post, d bracket 2 red 2 off

hi, all of the sudden, the mouse stop working. i shut the pc down, power up again and after 10 sec in win xp desktop, the same happened.
but now it just wont post! black screen and nothing happens. try switching the 2 mem sticks, reseting bios with the button and removing the batery.
also, the d-bracket shows leds 2 and 3 in red, 1 and 4 are off...
thanks in advance, gabriel

Quote from: Svet on 27-March-11, 06:28:26
this also could be the source of the issue,
use only matched memory sticks and either 1, 2 or 4 but not 3
right now are in slots 1-3, you say i should try them in 1-2, 1-4 or 2-4? anyway i've already try 512 in slot 1 only, 1gb in slot 1 only, and no ram at all but nothing changed..
[/quote]Quote from: Fredrik on 27-March-11, 08:22:11
A processer problem most likely. Is there a lot of dust?
no, just the usual. already remove it and installed again jus in case, same behaviour

645E Max HD and NIC problems?

I'm having three problems with my 645E Max and I'm not sure if they're with the motherboard or the hard drive and NIC.
Here are the problems:
1. Occasionally when I start my computer I get a "Hard drive: Imminent failure. Backup and Replace" error message.
2. Sometimes when I boot up, my computer goes in an very long loop. It restarts itself about 20-30 times before getting into windows.
Up until this point it sounds like a HD problem... but the HD seems to be working fine otherwise.
3. The NIC sometimes doesn't seem like it's getting power (the lights on the back don't light up) when I turn it on. Restarting usually doesn't help, but moving the NIC to another PCI slot usually fixes the problem. ((It's not a bad PCI slot, since moving it from one to another, and then back to the original one also fixes the problem))
Suggestions?

hehe..ok.. i had the same problem with my hdd's.
all i did was to switch places on the ide cable. fixed the problem. strange =)
1 ibm 120gxp 80 gig and 1 wd 40 gig.

Why can't Max Size of Post Data be increased?

We need to do a CFFILE upload of 1 – 3 GB videos and are having troubles.
(I know this is crazy, but FTP, network mapped drives, etc. aren’t going to leave an audit trail like an HTML form will for when people have to upload/update/delete bus incident videos.)
I can't increase the Max size of post data to even 2048MB without people getting "500" errors who are trying to upload small gifs or pdfs. If I move it above 2047MB, no one can upload anything.
Our setup:
CF Enterprise 8.0.1 with Hot Fix 2
2 - Win Servers 2003 R2 Enterprise x64 using replication, load balancing, and MS virtual machine.
CF is clustered so the Java class paths begin with
C:/JRun4/servers/HSWSD0C1O/cfusion.ear/cfusion.war/WEB-INF/...
CF Admin settings:
Max size of post data = 2047MB
Request throttle threshold = 4MB
Request Throttle Memory = 3072MB
Setting of 10 simultaneous requests.
Restarted CF services after Hotfix 2 install.
On the Application.cfm page I put
applicationtimeout="#CreateTimeSpan(0,4,0,0)#"
Basic code for uploading:

   <cffile action="upload"
      filefield="file"
      destination="#fileDirectory#"
      nameconflict="error"
      result="uploadResult">
This code works for small files IF I don't raise the max size of post data above 2047MB, which means we'll never get those videos up.
I've been fighting with this for weeks. Any ideas?
Thanks!

First thought is that Web Servers can impose their own upload throttles. You should check the documentation of your web server as well.
Secondly
I know this is crazy, but FTP, network mapped drives, etc. aren’t going
to leave an audit trail like an HTML form will for when people have to
upload/update/delete bus incident videos
What wouldn't FTP leave an audit trail? FTP communication can leave just as much, if not more, of an audit trail as HTTP communications.
Network mapped drives, I'm not so sure about, but I imagine there are ways to audit these as well. But then if you can use network mapped drives, you must be working with a well defined set of users all of which belong to a well defined network domain.
P.S. Also make sure that the max post size limits fit inside the overall limits of jvm memory. Trying to upload a file larger then the memory it can fit in sounds like a likely source of problems.

New BUg in 645E MAX 2

Hi, I found a new bug in 645E MAX 2. When you run the FSB at 145Mhz, and boot it up, the actual frequency that it will run is 87. something... I verified this in wcpuid. On top of that, I ran the sandra benchmark and that also verified that the FSB was running slower. I change the FSB to 144 and 146, and both ran fine ehehhe...

i guess the system cant handle 145 and set itself to safe values after freezing?

How do I post a slide show (from iPhoto 11) with music to Facebook from my mac

How do I post a slide show to facebook, from my imac. I am using it was made on iphoto 11 but I cannot figure out how to post or publish to post link. I also have slide show saved in itunes Thank you for your help

Export the slideshow from iPhoto
Then upload it to Facebook via their own uploader.

PC Won't boot now! D bracket showing all 4 leds red!

Ok this has got me stumped, on top of all my fan speed problems now that I have installed Windows 7 Ultimate x64, last night I found that my PC now WON'T BOOT AT ALL!!!!!!!!!!!!! ? The D bracket is now showing all red leds, which according to the manual, it means either the CPU is damaged or CPU is not seated correctly. But how can this be? I haven't even touched the CPU!?
Anyway, I have already tried removing the heat sink and reseating the cpu but it is still showing all 4 red leds.
This morning I tried booting it again but now I noticed that it is showing 2 red and 2 orange leds. What does the orange colour indicate?
I've also tried clearing the CMOS - no change.
I am completely at a loss now as to how my PC can all of a sudden just become totally unusable!? Is it the fault of Windows 7? Does Windows 7 somehow require more power to the CPU which may have fried it?
What can I do now?
CPU: AMD Athlon 3500+ Socket 939
Motherboard: MS-7100 MSI K8N SLI Platinum
Memory: 1 gig 2x512 sticks of DDR2 OCZ
Video card: gigabyte geforce 8600gt
Hard drive: 1x WD 74Gig Raptor, 1x WD 320 Gig Caviar
OS: Windows 7 Ultimate x64
PSU: Antec True 480Watts

Quote from: chef jeff on 11-November-09, 22:31:50
Have you tried another processor? With your fan issues it concerns me the processor my have gotten too hot.
Yes, this is certainly a possibility and I haven't ruled this out yet. However the problem is trying to find someone with another socket 939 cpu and mobo. I know someone who has a Shuttle PC but he majorly cbfed taking it apart and trying my cpu out.
But even if the processor got too hot, why is the D Bracket showing 2 red and 2 orange leds. Shouldn't it be showing all 4 as red? That's why I still believe the BIOS maybe corrupted as well.
Anyway, I'm getting in a technician today so hopefully he will be able to try it out somehow.

Blog posts don't show

Hi, im creating the blog module for my website, the inconvenient is that the Post doesnt show, just the look and feel. Here is the URLin case you guys can help me. Thanks a lot!
http://www.extensiondigital.co/_blog/blog-extension-digital/post/this-doesnt-show

It's your CSS. You have visibility hidden set on the "wrapper clear" from skeleton.css line 477

645e max 2, no post & d-bracket shows 1-4 as green

Similar Messages

Maybe you are looking for