7965 Display Error - Port Configuration Error

Community,
I have a customer who is experiencing what appears to be a cosmetic error on their 7965s. When deploying endpoints into the field they have found that if they hard code the speed/duplex to 100/Full on the PC port of the phone they get a "Port Configuration Error". The funny thing is that the PC appears to function normally at 100 Full. When I change the endpoint to auto-negotiate from CUCM the error goes away.
Has anyone ever run into this?
Endpoint:     7965
Protocol:     SIP
Load:          SIP45.9-3-1SR2-1S

No worries, how about the actual switch port on the phone? Are both the PC and SW ports set to Auto or 100 Full? I would still be curious about what the network port on the switch is set to as well. I am running 7965G's in both SCCP and SIP form and no matter how I have the ports set and cannot recreate. I am also running 9.3.1sr2 firmware on both.

Similar Messages

Error on Send Port configured using HTTP adapter

Hi All,
For Load balancing purpose we have created new host and host instance and changed send handler for send port configured using
plain HTTP adapter.
We are getting below error after change:
A password is mandatory if UserName is specified
Parameter name: Password
Please advice.
Thanks
Pooja Jagtap Software Engineer KPIT Cummins

Have you updated the password for your Host instance . Try restarting your host instance once .
Thanks
Abhishek

Problem with the error at DIO port configuration

I am working on the design of a model of a computer controlled Fuel Injection system using Gasoline Direct Igniton technology. I am using PCI-6025E as my data card and SCB-100 Connector block. My application is to get the digital input from the shaft encoder and the solenoids[acting as Inlet and exhaust valves]get actuated according to the VI. When I am trying to run the program theres an error 10001 occured at DIO port configuration. The statement is as" The error occured at the input string, the arrangement or ordering of the characters in the string is not consistent with the expected ordering". I checked the shaft encoder[S5S-50]pin out connections using an oscillograph and the voltages are as expected. Please let me
know the possible areas where I can figure out the error.

Maruthi;
You are probably using VIs that are not supported by that DAQ device. That DAQ device of yours only allow unstrobed digital updates, meaning that the digital lines will be updated by Software calls.
Since you probably need high speed/accuracy on your digital updates, you would be better served by using the PCI-6534 instead.
Hope this helps.
Filipe A.
Applications Engineer
National Instruments

Windows 7 or Windows Server 2008 R2 domain join displays error "Changing the Primary Domain DNS name of this computer to "" failed...."

Hi,
Windows 7 or Windows Server 2008 R2 domain join displays error "Changing the Primary Domain DNS name of this computer to "" failed...."
DC:windows Server 2008 R2
Domain functional level:Windows Server 2003
When Winxp join domain, have no this error message.
I checked http://support.microsoft.com/kb/2018583?wa=wsignin1.0 does't work.
There have 3 suggestion in this article:
1.The "Disable NetBIOS over TCP/IP" checkbox has been disabled in the IPv4 properties of the computer being joined.
Doesnt's work.
2.Connectivity over UDP port 137 is blocked between client and the helper DC servicing the join operation in the target domain.
On my DC, I run netstat -an, reslut as below:
UDP 192.168.20.3:137 *:*
3.The TCP/IPv4 protocol has been disabled so that the client being joined or the DC in the destination domain targeted by the LDAP BIND is running TCP/IPv6 only.
We are not using IPV6.
This server recently updated from Windows Server 2003 to Windows Server 2008 R2. Before upgrade, when Win7 and Win2008 join this domain, also have the same error message.
Please help to check this issue.
Thank you very much.
BR
Guo YingHui

Hi Guo Ying,
I have faced this critical error which makes over-writes the host names in the domain when you join.
For example: Already you had a host name called as PC.domain.com in the domain.com Domain.
When you try to add the another host name called as PC in the domain.com Domain, it doesn't give you the duplicate name error on the network it does over-write the existing host name called as PC.domain.com & it will add the new host name into the domain.
Host name which got over-written will get removed from the domain. I faced this issue in my project. My DPM host name got removed from the Domain & new host name got joined into the domain which halted my backups for one day.
Final Resolution is as follows:
You need to start the dns console on the DC & drop down the domain name.
Select the _msdcs when you click on _msdcs it will show the Name Server's list on the right hand side.
You need to add the Domain Naming Master under the _msdcs or add all the domain controllers which you had.
After you add the Name server's try joining the PC OR Laptop to the domain which is successfully joins it.
Regards
Anand S
Thanks & Regards Anand Sunka MCSA+CCNA+MCTS

"cannot open display" error meaning

I'm trying to get dwm running for a while now, and when I try to run it, it says "cannot open display". Then I thought, ok, maybe i have to install an X server, so I got Xorg, installed it, removed dwm and then recompiled it, but I got the same error. Then I thought that maybe I didn't have the right configurations (even though I never bothered config.h or config.mk), so I got gnome (hoping that it would auto-configure itself) so that I can test if it's something with dwm or some other problem with the system. When I tried to start gnome, I got the "cannot open display" error, again (my keyboard will never forgive me for what I did when I saw that).
I went through dwm's wiki more than once, googled the problem, read about Xorg, I just don't know what I'm doing wrong.
Everything was done on a fresh netinstall.
Could you please help me out with this? (Or just link me to somewhere I can find some meaningful information about the problem)
Last edited by imv (2012-04-01 15:02:00)

@lifeafter2am I read that, xorg_server and xorg_apps were already installed, since I installed xorg (as in, the whole xorg package). xinit, startx ~/.xinitrc and /etc/X11/xinit/xinitrc , all files/programs mentioned in the wiki, ar missing, though, perhaps it's a hint of some sort
@istbrad212 the video card driver was already installed
Sorry for the slow responses, I have to constantly reboot in order to try everything.

Problem displaying error page of web.xml when using JSF, Ajax4jsf

Hi,
My application is using MyFaces, RichFaces and Ajax4jsf. When i try to display error page configured in web.xml, i am getting exception "Error while processing error page".
my web.xml contents are as follows:
<?xml version="1.0"?>
<web-app version="2.4" xmlns="http://java.sun.com/xml/ns/j2ee" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://java.sun.com/xml/ns/j2ee http://java.sun.com/xml/ns/j2ee/web-app_2_4.xsd">
<filter>
<display-name>RichFaces Filter</display-name>
<filter-name>richfaces</filter-name>
<filter-class>org.ajax4jsf.Filter</filter-class>
</filter>
<filter-mapping>
<filter-name>richfaces</filter-name>
<servlet-name>faces</servlet-name>
<dispatcher>REQUEST</dispatcher>
<dispatcher>FORWARD</dispatcher>
<dispatcher>INCLUDE</dispatcher>
</filter-mapping>
<filter>
<filter-name>extensionsFilter</filter-name>
<filter-class>
org.apache.myfaces.webapp.filter.ExtensionsFilter
</filter-class>
<init-param>
<description>
set the size limit for uploaded files. Format: 10 - 10 bytes 10k
- 10 KB 10m - 10 MB 1g - 1 GB
</description>
<param-name>uploadMaxFileSize</param-name>
<param-value>100m</param-value>
</init-param>
<init-param>
<description>
Set the threshold size - files below this limit are stored in
memory, files above this limit are stored on disk.
Format: 10 - 10 bytes 10k - 10 KB 10m - 10 MB 1g - 1 GB
</description>
<param-name>uploadThresholdSize</param-name>
<param-value>100k</param-value>
</init-param>
</filter>
<filter>
<filter-name>Seam Redirect Filter</filter-name>
<filter-class>org.jboss.seam.servlet.SeamRedirectFilter</filter-class>
</filter>
<filter>
<filter-name>KTServletFilter</filter-name>
<filter-class>com.kenexa.core.system.KTServletFilter</filter-class>
</filter>
<filter-mapping>
<filter-name>extensionsFilter</filter-name>
<url-pattern>*.jsf</url-pattern>
</filter-mapping>
<filter-mapping>
<filter-name>extensionsFilter</filter-name>
<url-pattern>/faces/*</url-pattern>
</filter-mapping>
<filter-mapping>
<filter-name>Seam Redirect Filter</filter-name>
<url-pattern>*.jsf</url-pattern>
</filter-mapping>
<filter-mapping>
<filter-name>KTServletFilter</filter-name>
<url-pattern>*.jsf</url-pattern>
</filter-mapping>

<listener>
<listener-class>org.jboss.seam.servlet.SeamListener</listener-class>
</listener>
<listener>
<listener-class>com.kenexa.kr.web.KRServletListener</listener-class>
</listener>
<servlet>
<servlet-name>faces</servlet-name>
<servlet-class>javax.faces.webapp.FacesServlet</servlet-class>
<load-on-startup>1</load-on-startup>
</servlet>
<servlet-mapping>
<servlet-name>faces</servlet-name>
<url-pattern>*.jsf</url-pattern>
</servlet-mapping>
<error-page>
<exception-type>java.lang.Throwable</exception-type>
<location>/rc/systemError.jsf</location>
</error-page>
</web-app>
As per the configuration, when exception is thrown out of the application, container tries to display systemError.jsp page. If we want to include the JSF tags in systemError.jsp page, the request should pass through FacesServlet, so in the <error-page> <location> tag systemError page is specified with the extention systemError.jsf though it's actual extention is .jsp
When exception is thrown from the application container invoke the error page but, while rendering systemError.jsf page exception is thrown saying "Exception processing error page "systemError.jsp" "
To solve this problem i've gone through several forums, materials.
In one forum a guy said, JSF1.1 spec has some problem in displaying error pages. To solve this don't write <f:view> tags in the error page, use <f:subview> intstead. By reading this, i again changed the contents of systemError.jsp page replacing <f:view> by <f:subview>. But the error is still repeating.
Finally what i found is, when we use Ajax4jsf in the application, its AjaxViewRender class is throwing exception while rendering error pages configured through web.xml.
So what i did is i changed error page extention from .jsf to .jsp in the <location> tag. Now jsf won't come in the picture and remove JSF related tags from the systemError.jsp page.
<error-page>
<exception-type>java.lang.Throwable</exception-type>
<location>/rc/systemError.jsp</location>
</error-page>
Any comments are welcome----------------------------------------------------------------

I too iam facing the same problem could you advise if you have found any solutions
-Ram

"Page cannot be displayed" error when attempting to download large dataset.

In the following code, can anybody please tell me at what point the data actually starts to get transferred and the popup "download file" box appears? I'm thinking that the dialog box should appear on the first outputstream.write and start transferring data. However, I think it's not transferring the data until the while loop has finished! That's bad because this is a real long process and I eventually get "Page cannot be displayed" error. On a smaller dataset (shorter while loop) everything seems to work correctly. Is there some sort of a web server configuration that tells it to write out the data ONLY if outputstream closes? I really need it to write out the data as it's coming in. Code is below and thanks in advance.
response.setHeader("Expires", "0");
response.setHeader("Content-disposition","inline;filename=Download.csv");
response.setContentType("application/x-msdownload");
outputStream = response.getOutputStream();
bufferInBytes = this.getData();
while (bufferInBytes != null)
outputStream.write(bufferInBytes, 0, bufferInBytes.length);
outputStream.flush();
bufferInBytes = this.getData();
outputStream.close();

Hi All,
Thanks for all your help.
Seems I already found out the issue.
Since we are using "Personal Home Page" for the system profile option "Self Service Personal Home Page Mode" I checked oracle note and found out
that 11i did not support this mode. Maybe this is the problem that is why we are getting page cannot be displayed error when only 1 responsibility is active.
The way to fix this, is to use mode 'Framework Only' instead of 'Personal Home Page' as Oracle are phasing out mod_plsql based UI and it will not be present in future releases. No maintenance is being performed (i.e. bug fixes) to the mod_plsql based UI technology.
Please check this note for more clearer explanation:
Is The 'Personal Home Page' Mode Supported In Oracle 11i Applications? [ID 368628.1]
Again, thank you for your help!

HR portal display error

Dear experts,
We got two users asking about the display error on our HR portal page.
When users log in the HR portal and try to open the Performance Appraisal page, the error message appears within the following error messages:
The page cannot be displayed
The page you are looking for is currently unavailable. The Web site might be experiencing technical difficulties, or you may need to adjust your browser settings.
And I checked the detail information about the PA page,
Portal Component: com.sap.portal.appintegrator.sap.BSP
Object ID: pcd:portal_content/com.perlos.PerlosContent/com.perlos.MBO/com.perlos.Roles/com.perlos.MBO_Mgr/com.perlos.MBO_Head/com.perlos.MBO
I don't know how can I check for the display error. Is the Portal setting or some configuration problem for IE?
Please help me, thank you very much.

Dear Nolasco,
    I think the authorization should be fine.
    I used the user's account and log on HR portal on my notebook and switch to HR administration page,
clicking an work list and the Adobe document display with the new IE screen.
    All above actions can work fine on my computer, but user's don't.
    When user log on HR portal on his computer and change to HR administration page, the work list field is alway with "Loading" image, but the Open processes can show the information.
    I just don't know that when the Work list field is loading data, which component will be used? The java component, the SAPGUI component, or something else?
    If i can know which part cause the loading image in the work list field, I can check user's working environment.
    Could you give me more information?

Page cannot be displayed error while accessing links on DAS page

Hi,
I have installed SSO server along with DAS on a single m/c. While installing i gave OID instance hostname and password. After installation when i access the DAS homepage and click on Login or Myprofile url is is throwing Page cannot be displayed error page
i found following in the Apache\logs\error.log
[Wed Nov 23 10:28:26 2005] [error] [client 198.186.43.113] [ecid: 1132759706:198.186.43.113:2408:2136:6,0] MOD_OC4J_0376: Request initial processing failed in ac worker with HTTP status code 1. This status will be passed back to the listener for error handling.
I checked OC4J_SECURITY and HTTP_Server status. They are up and running. OID is also running.
Any solution for this problem?

Hi,
I once faced a similar problem - I am not sure if the issues are related, but here goes :
I figured out that DAS uses mod_osso to connect to the SSO Server. I hadn't configured mod_osso to correctly talk to the SSO Server. I used the ssoreg.sh script in the $ORACLE_HOME/sso/bin to make the mod_osso " talk " to the SSO Server.
After this, the DAS started working properly.
BTW, what's your AS instance version ?

When Loading a Webdynpro Application getting Page Cannot be displayed Error

Hi All,
Webdynpro application when loading through Internet or VPN connection is displaying a Page Cannot be displayed Error and when we try to refresh it automatically loads the page.
Application is launched from the SAP Netweaver Portal. Operating System is Windows Vista and IE -7. Can anyone please let us know how to resolve the issue.
Any help is higly appreciated.
Thanks,
Madhavi

Hi,
How is configured the Cache of Your Internet Explorer, try to set it to verify the new version at "Every visit to page".
Maybe a cache problem.
Best regards

Strange Display Errors with certain Applications (ATI X1600) [SOLVED]

Hi everyone!
I have been using Arch now for a year or so and am very happy with it, but now there is a problem I unfortunately can't solve by my own.
Since a month or so certain applications (like emacs, feh or gimp, if i try to manipulate the drawing surface) cause very strange display errors. When I try to take a screenshot, they can't be seen, so i made to photographs
Image 1 (one instance of emacs under awesome-wm): http://img850.imageshack.us/img850/5186 … 112158.jpg
Image 2 (two instances of emacs under awesome-wm): http://img24.imageshack.us/img24/822/im … 112158.jpg
I already tried another display manager (musca) but there the same applications cause the same type of error.
Maybe the version 6.14.0-1 of xf86-video-ati broke my system, but I don't know.
Has anyone had similar problems or probably a solution?
Thanks in advance
Maak
P.S.: I hope this is the right forum for this topic.
Files:
/var/log/Xorg.0.log https://pastee.org/q3nn2
Output of lspci https://pastee.org/db7n8
UPDATE:
Hi everyone, again!
I just successfully downgraded the driver and the errors are gone
If someone has the same errors, here is the PKGBUILD (taken from SVN; only the version numbers and sha1sums are modified)
pkgname=xf86-video-ati
pkgver=6.13.2
pkgrel=1
pkgdesc="X.org ati video driver"
arch=(i686 x86_64)
url="http://xorg.freedesktop.org/"
license=('custom')
depends=(libpciaccess libdrm udev pixman ati-dri)
makedepends=('xorg-server-devel' 'libdrm' 'xf86driproto' 'mesa')
conflicts=('xorg-server<1.9.0')
groups=('xorg-drivers' 'xorg')
options=('!libtool')
source=(${url}/releases/individual/driver/${pkgname}-${pkgver}.tar.bz2)
sha1sums=('f9d379a884a833829ab1942de4ad4f4766cdcd46')
build() {
cd "${srcdir}/${pkgname}-${pkgver}"
./configure --prefix=/usr --enable-dri
make
package() {
cd "${srcdir}/${pkgname}-${pkgver}"
make "DESTDIR=${pkgdir}" install
install -m755 -d "${pkgdir}/usr/share/licenses/${pkgname}"
install -m644 COPYING "${pkgdir}/usr/share/licenses/${pkgname}/"
Last edited by Maak (2011-03-11 23:32:46)

http://bbs.archlinux.org/viewtopic.php?id=89926

Netflix display error with Safari 8/OSX 10.10 Yosemite

I am having an issue with playing Netflix content through Safari since upgrading to Yosemite. Specifically, Netflix will start to play the content and then display an error after a few seconds. The error reads "Whoops, something went wrong... display error. There appears to be a display problem. Please ensure your monitor is HDCP compliant and is not mirror using airplay."
My monitor is HDCP compliant (HP ZR30W) and it's the only monitor connected to my 2014 MacPro. I presume this is an issue with the latest version of Safari and all the next extensions Apple added to support Netflix streaming without the Silverlight plugin.
Anyone have a solution for this or seen the same problem? The new Safari is crazy-fast and I'd prefer to use it with Netflix. Hate bailing to Chrome.

I just got it to work, and I think I may know why, just in case it helps anyone.
My setup:
Mac Mini (late 2012), with two monitors connected:
One dell HDMI monitor, hdcp compliant, plugged into the Mac Mini HDMI port.
One dell monitor plugged into thunderbolt via thunderbolt-VGA adaptor.
Unplugging the second monitor from the thunderbolt-VGA adaptor fixed the issue, and now Netflix plays with the HTML5 setting turned on! So it would appear that the second monitor was the problem. Which would track with what this page says:
Apple Mini DisplayPort adapters: Frequently asked questions (FAQ)
The page states that a Thunderbolt-DVI connector should work. Luckily this monitor has both, so the next thing I will try is to buy a Thunderbolt-DVI adaptor and retest with both monitors attached (I don't have one at the moment). If that works, I'll post the results, maybe next week.
This kind of stinks because I've always been two-monitor dude, I like having a movie playing on one monitor while I work on the other for example. For now, until I get the adaptor, I'll switch netflix back to using silverlight, which seems to still work with both monitors attached.

Getting a Page Cannot be Displayed error while uploading a Contract Document in SAP E-sourcing for size 500mb

Hi Guys,
I am getting a Page can not be displayed error while uploading a COntract Document in SAP-E-soucing 7.0.
Maximum Size set in Our SYSTEM is :9765MB.
Approx size of the Document tried is more then 300MB.
Appreciate your help on this.
Regards
Tarun

Hi Tarun,
Please check the below system properties using system user login
attachments.maxSizeKB.buyers - "Maximum size in KB of a employer-attached attachment file"
attachments.upload.enable.buyers- " Enable/Disable uploading of attachments by internal users"
Also Please check with other attachment, contracts related properties in the System.
Let me know if this helps.
Thanks,
Raj.

Display error message in batch job log

Hello
I have a batch job running and I have an error coming during some validation logic.
The problem is I need to continue the batch job when this error message comes and it should not cancel the batch job as it is doing currently but display that error message in batch job log, there are more similar error messages coming in job log and job gets finished, but when my error message comes job gets cancelled.
I cannot give it as info message as it will give wrong idea about message type.
Is there any FM by which we can add message in job log?

Sanjeev I have done that but problem is I do not want to give that as Information message but Error message only and continue processing.
If you see in screenshot 3rd message is given by me as information and you can see error messages also 6th and 7th and job continued till it is finished
Basically I want that 'I' to be displayed as 'E'.
Display error message in batch job log

"XML page cannot be displayed" error

Using XML output on a table with more than a few rows falls over with a "XML page cannot be displayed" error. Sometimes only the error is displayed, sometimes some rows are displayed with this error at the end of the page (eg the DEMO_STATES table)
Can anyone advise if there is some sort of limiter at work here?
Thanks,
Barry

i'm pretty sure that error comes up when your browser (ie, specifically, i believe) can't render the xml data it's received. i'm also pretty sure, as the full message implies, it's because it doesn't know what style sheet to use when you go to that page. in short, it's a browser config issue. one way to bypass it (to at least prove that it's a browser issue) would be to create a link to your page, right click the link, and do a "Save Target As...". the resulting file will be your valid XML one. fwiw, i've had better luck controlling the manner in which my xml data is received when i use mozilla or netscape (but i'd imagine there's just some setting you'd toggle in IE to avoid your issue).
hope this helps,
raj

7965 Display Error - Port Configuration Error

Similar Messages

Maybe you are looking for