Acquiring pressure data using daq assist

Hi all,
I want to use DAQ Assist to measure the pressure.When i select DAQ Assist>Acquire Signals>Analogue Input>Pressure>Pressure(Bridge) then is says 'no supported devices found'
What should i do?
thanks

I have Trafag pressure sensor anyway i give up doing it by daq assistant.I did it by using another daq tools.But now i have a new problem in calibration of sensor so i will post a new question

Similar Messages

Getting the data in file using DAQ assistant in Labview

I am using SCXI 1000 chassis, SCXI 1125 input module and SCXI 1320
terminal.
I am using DAQ assistant in labview to obtain temperatures and store it in
a file. The experiments run the whole day and I need the whole data
generated during this time to be stored in a single file, but I am unable
to store it in a single file.
Can someone please give me some insight as to how can I achieve this?

Hi Mr,
It would be helpful to see your code to see exactly how you are acquiring the data. Are you doing continuous buffered measurements? Or are you performing single point temperature measurements in a while loop?
Either way you will want to use the "write to spreadsheet" VI in your loop. Simply wire your data into the "write to spreadsheet" vi and se the "append to file" input to TRUE. This will make the data add on to the end of the file with each iteration of the loop. The "write to spreadsheet" VI is located in the file IO pallette in LabVIEW.
Thanks,
Sal

New project using Daq Assistant or not ?

Hi everybody,
I need to create a software to do some realtime acquisition & analysis.
I trained myself a little bit on c# lessons to get use to this programming language; I’m also discovering Measurement Studio & Visual Studio. (I’ve background in C++).
My software will have 2 modes :
Continuous acquisition, signal plotting + signal processing & plotting (fft, 1/3 octave band filter)
Triggered acquisition, signal plotting + signal processing & plotting (fft, , 1/3 octave band filter)
I have examples in my National Instruments directory which don't use daq Assistant and code is different from generated files with daq Component.
If I use Daq Assistant ( http://www.ni.com/tutorial/4652/en/ )
I know that the code to create channel is stored in DaqTask.cs
Plotting :
NationalInstruments.AnalogWaveform<double>[] acquiredData = daqTaskComponent1.Read();
waveformGraph1.PlotWaveforms(acquiredData);
When I look to examples, like "MStudioVS2010\DotNET\Examples\DAQmxWithUI\SpectrumAnalyzer\cs "
all code to create channel is generated in Mainform.cs, there is no Daq Assistant (http://www.ni.com/tutorial/5409/en/ )
and there is a slight difference between acquired type :
private AnalogWaveform<double> data = new AnalogWaveform<double>(1000);
data = reader.EndReadWaveform(ar);
acquiredDataWaveformGraph.PlotWaveform(data);
Questions :
What is the difference between AnalogWaveform<double> and AnalogWaveform<double>[] ? why it's not the same type ? I need to do some signal processing with this signal, so what type should I use for my application ?
I didn't succeed to configure my 2 modes in daq Assistant (continuous and triggered acquisition) is it possible or should I create 2 Items in my solution, one for continuous acquisition and on for triggered acquisition ?
Kind regards,

Check out the downloads section of iLounge.com. There are a handful or two of applications that will help you transfer songs from the iPod to the computer.
Another option is to network the two computers together and transfer the iTunes folder to the new Mac. All you need is an ethernet cable and to turn on file sharing in the Sharing preference panel. Depending on how old your "older" Mac is, you might need a crossover ethernet cable.
A third option is to hook up the two computers using a Firewire cable. On the older Mac make sure it is shut down, hook the two computers up, turn on the older Mac while holding down the "T" key. On the new Mac you should see the old Mac's hard drive show up. Just find the iTunes music folder and copy it over. You could also use the Migration Assistant which will be in the Utilities folder of the new Mac.
Hope this helps.

How to use DAQ Assistant to display two analog channels in a XY Graph

Hi,
I am new to LabVIEW. I have been assigned a project in which i have to display two analog signals from an analog potentiostat i.e. voltage and current (also a voltage signal) on a graph using labview. I am using a myDAQ device to acquire these analog signals and I am using labview 2013 to display these signals on a graph. I am using DAQ assistant to configure these signals. Rightnow I have separate graphs for each channel. However, I want a single XY graph to display one voltage as a function of the other i.e. I want to have voltage on the X-axis and current output on the Y axis. Any kind of help is greatly appreciated.
I have attached a screenshot of the VI. that I have made.
Regards,
Max
Attachments:
New Microsoft Word Document (2).docx ‏32 KB

Thanks for the quick response. I was able to make a X-Y graph. However, I can only see a dot floating around. It's not drawing anything. I want to see it making a plot as it collects data. Also, I want to see the complete waveform formed when I stop the VI.
Thanks,
Max

When using DAQ assistant to read frequency

When using DAQ assistant to read frequency and Task timing is set to:
N Samples, Clock settings to read 26,
Frequency setup to rising edge,
1 counter with 10 kHz to 1 kHz range.
I get back a single number.
Can I assume this is an average reading of 25 samples with the first sample unused?
What is the base clock used?
Is the “26” 26 cycles of the frequency to be measured?

Hello,
If you choose to acquire N samples from the DAQ Assistant then it will acquire all of these samples and return them to LabVIEW as an array. However, when you use the DAQ Assistant it outputs the data in the dynamic data type first. This data type makes it easy to graph and run the data through other express VIs. If you were to create a Numeric Indicator from this data type it would just display the last element from the dynamic data array. To display this data properly in a numeric format convert the dynamic data to an array of doubles by using the Convert From Dynamic Data function in LabVIEW. Then you can select to convert it to a 1D array of scalars and when you create an indicator off of the output of this function all of the data should be displayed.
The timebase that is used for lower frequency measurements is the onboard clock, which is internally connected to the Source. Then you connect your signal to be measured to the Gate of the counter. Since the frequency of the onboard clock is known it can be used to calculate the frequency of an unknown source based on when the counter is on and off (determined by the Gate).
Have a good day,
Brian P.
Applications Engineer

HT4889 I just transferred data using migration assistant from a macbook prop to a macbook. I am trying to log back into the user that was on the pro but is now on the macbook with the same password as before, and it says my password is incorrect.

I just transferred data using migration assistant from a macbook pro to a macbook. I am trying to log back into the user that was on the pro but is now on the macbook with the same password as before, and it says my password is incorrect?

Suggest you try the password for the Macbook, not the previous one.

Can't use Daq Assistant in Labview 7.1

hi! I have Labview 7.1 installed and an AT-MIO-16E-10 NI board. I can see the board in MAX\devices&Interfaces\traditional NI-DAQ but i can't run any tests(Test panels). I don't know if this is normal for this NI-DAQ model. anyway my main conceirn is that i can not use DAQ Assistant in LabView(when i double click on it or right click->Properties nothing happends). So i can't use my board in LabView. please help! thanks a lot

You can use your board in LabVIEW but you can't use it with DAQmx. In the DAQ Quick Start Guide, the supported devices are listed and the AT E series is only supported with traditional DAQ.

I am trying to log data from 4 voltage input signal using labview, but when i use DAQ assistant i am able to log data from one signal at a time only.

I am trying to log data from 4 voltage input signal using labview, but when i use DAQ assiatant i am able to log data from one signal at a time only.I am trying to get all 4 input data to logged in a single file againt time. I am new to Labview, I need to sample this data within a couple of days can someone help please.

Naveen
Check out the info in the Analog Input section of the document linked below. (Ignore the part about Global Channels.) In Figure 5, notice that you can select multiple channels while holding <Ctrl> or <Shift>.
Developer Zone Tutorial: NI-DAQmx Express VI Tutorial
Kyle B | Product Support Engineer | ni.com/support

How do I use DAQ Assistant to output DC on an AO?

My background includes 15 years of programming PLC's. AO's were simple. You passed the AO a value between preset ranges and it output a proportional voltage signal based on the hardware capabilities.
I foolishly thought LabView and DAQ AO's would be about the same. I built a vi to generate a DC signal which I could control the amplitude of. I also tied it to a chart to monitor how it worked. I managed to draw some very pretty ramping pictures on my chart, but when I put a DMM across the physical terminals I see no voltage.
Then I used MAX to test the channel and measured it again. Now I see voltage on my DMM. I was attempting to use the DAQ Assistant to do this. Do I need to force it to re-read the changing value I am sending it? All of the examples I find show me more primitive methods, and I could not seem to get any of them to do what I want either. I need to send a speed reference to a DC drive.
My incorrect method was to recursively add a value for ramping the signal up or subtract to ramp down. This method works perfectly on an industrial PLC. I connected a chart to the signal just as it entered the DAQ Assistant, but the only way I could check the actual was with the DMM.
Are there any examples that use the Assistant? If not then I guess I will have figure out how to use the primitives anyway.
technomage

Hello technomage,
It looks like we have discussed this problem in another thread (found here). If you have any other questions about it, please post there.
Regards,
Jesse O.
Applications Engineering
National Instruments
Jesse O. | National Instruments R&D

Using DAQ-assist to input a waveform; need help building a counter to count voltage "spikes"

Hey all! I'm pretty new to labView and even newer to this forum, but its nice to meet you all...I hope that perhaps someone can help me with my problem.
Allow me to begin by detailing the specifications of the problem. I am an undergraduate student, and have a job doing research in a MEMS (micro/nanotech) lab. The graduate student I am making this program for is working on biomedical applications; eventually, the program will be connected to a microdevice that has a tiny channel in it, cut through a wee little capacitor, which blood will run through. As red blood cells pass this capacitor, the voltage will spike; meaning that for each voltage spike, we can (and are trying to) count the number of red blood cells.
However, I am still in the early developement of the program, so this above specific info is not that important. Basically, I am using a function generator to input a waveform to the DAQ assistant of, say 500 mV. I am trying to write a program that increments a counter every time I turn the voltage above say 550 mV (peak-to-peak), counting the number of simulated "spikes." I have tried quite a lot to write a working program, and although I have not gotten it to work yet, I will post a screenshot of my most recent attempt HERE:
I thank you in advance for any helpful tips, advice, or straight up assistance you may be able to give me. Please ask me any clarifying questions about the program I wrote or the application, or anything. Happy Friday!

Hey guys, it's been a while! A lot of stuff has been happening in my life and I have had virtually no time to work on my LabView project.
I did create a LabView program based off IanW's reccomendation. I am unsure of what exactly is going wrong, but when I run it, only a simple "snapshot" of a waveform from the DAQ shows up in the graph. Even when I put the DAQ assist in a seperate while loop, the same thing happens. I am including a screenshot of the project in case I am messing something entirely different up. If you happen to read this, I really appreciate your help and thank you Ian!
I am also having a random issue with the filter signal VI. So that background signals in the actual experiment do not read as "spikes" I have been instructed to include a high-pass filter in the VI. However, everytime I use the high pass filter VI, it botches my signal and turns it into a bunch of noise! I, nor my graduate mentor (who isn't too well-versed in LabView) have any idea why this is - we've tried using different types of filters to no avail.
Lastly, I would like to talk to Peter about a few questions I had abour LabView design. In case you're still around, I will write another post later today with more detail. In the meantime, I will try to find some of the example VIs about shift registers All who read this have a great day!
Attachments:
count spikes pic.png ‏29 KB

Transferring data using migrant assistant

I have a white macbook with snow leopard, i have purchased a new aluminum macbook with leopard. upgraded the new one to snow leopard and now want to transfer files (music,photos,settings,apps etc) from mac to mac.
I was using migrant assistant, after completion it it transferred a small portion of photos about 10%, and thats it. I was using an ethernet cable to connect them together. none of my settings or documents transferred either. Is this the only way to complete this transfer and if so, has anyone got any tips or had this problem?
Otherwise I'm looking at using a memory stick and doing it the long way.
thanks

You might get better advice asking in the Snow Leopard set-up forum, here:
http://discussions.apple.com/forum.jspa?forumID=1337

Acquiring continuous data using an event structure

I am new to labview, having recently taken the Core I and II courses.
I am programming a test rig to acquire the linear position of a hydraulic cylinder and plot it over time. In programming this code, I elected to use an event structure so that when a front panel button is pressed, a certain part of the test is run.
In one particular part of the test, called the Snub Test, I need to measure the position of the cylinder over time and plot it to a graph. The data acquisition needs to be continuous, however the event structure only allows the loop to run once.
I have attached a portion of my code for reference.
Can someone please advise how I can get this data acquisition to run continuously until the user (or a reference trigger) stops the test?
Thanks
Attachments:
Front Panel.vi ‏115 KB

A few comments to your VI in general:
You changed the stop button to "switch until released", most likely because you fabricated a race condition and did this as a quick fix. The reason is (1) your placement of the stop terminal outside the event structure and (2) the use of a local variable wired to the stop condition. The button terminal of a latch action boolean belong inside it's associated event case! This way it gets read (and reset to false) when the event occurs. In your case, the local variable and the button get read before the event occurs and the loop needs to spin once more at the event that occurs when you release it (true->false). At this point, the local is still true from the earlier event and the loop stops. Correct would be: latch action, stop terminal inside stop case and wired to the stop condition from inside the event. Other cases use the default output (false) and don't stop the loop.
Your "equal false" code fragment is just an invert, right? So why complicate things?
Why do you need a wait if there is an event structure?
LabVIEW Champion . Do more with less code and in less time .

How to properly read data from one DAQ-assistant and write simultaneously with another DAQ-assistant (which is inside a loop)

Hello.
I'm a newbie working on my Master's thesis conserning a project that is based on old G-code made by another newbie so bear with me.
I need to create a sequance of output controls. For this I'm using a for loop that eventually creates two triangular ramps during a period of 90 seconds. I've confirmed that this function works properly by measuring the actual output of the DAQ-decice (NI USB 6353).
The problem is the following: During this controll-cycle I need to simultanously collect data from the same DAQ-device. At this point there is only one DAQ-assistant output-block in the main loop of the program and all the signals are derived from it to where they are needed.There is a case-structure (the bottom case structure in the picture) that contains the functions needed to collect the data during the test cycle. However these two actions, outputting data and inputting data, are not synchronized in any way which may be the reason why I get the 200279 error or alternatively the 200284 error during the test cycle. I've tried changing the sample rate, buffer size and the timeout time as adviced but nothing seems to help.
What would be the simplest way to solve this problem?
Help is greatly appreciated!
Attachments:
problem.jpg ‏206 KB

Thanks for quick reply.
However, I did try it (see the picture) but I still have a problem: I only get 100 samples / channel during the test sequence (all from the first seconds of the sequence) in total even though I've set the data aqcuiring DAQ-assistant as "continous" and "samples to read = 95k" and rate is 1000Hz.
Edit.
And lastly, I have trouble adding this "extra" DAQ-assistant to the vi. because I get an error about a resource (The 6353) being reserved, even though I connected a false constant to the "STOP" -input of the main DAQ-assistant.
Attachments:
is_this_what_you_meant.jpg ‏212 KB

Dynamically passing data into a running while loop from a DAQ assist. in an ouside while loop

Hello, I'm currently a student working on a senior project and I'm trying to do a state machine that will turn off and turn on a compressor depending on time and coprocessor failure.
In the run state, wich is #1 on the case structure box I placed the DAQ assist. Which takes in data from an accelerometer. If the accelerometer's value is above the limit four times it will end the loop or if the time runs out it will end the loop.
The problem I am having is that i need to run four compressors. I was thinking about having four case structures all within the outside loop, but I can only have the DAQ assist in one location. This means that I now have to move the DAQ assist out of the run loop or run all four compressors in the one case structure. If i remove the DAQ assist. I can only get it take in data once when the loop starts and never again. I understand why, but is there a way to dynamically pass data froma DAQ assist. into a running loop?
Also on a side note, i can't find a tutorial on how to really create a state machine using Enums. Does any one know where to find this.
I have attached my curent program.
Thank you for your help,
Ryan
Attachments:
TEST STAND STATE MACHINE 2-28-07.vi ‏288 KB

in labview choose file->new... then pick standard state machine and there are instructions.
you can create a custom control and either use an enum, text ring or menu ring. Edit the values and then save the control and drop into your vi and you can wire this to your case structure
- James
Using LV 2012 on Windows 7 64 bit

Blood pressure data acquisition

Hello,
I have some problems with blood pressure measuring.
I have Blood Pressure Sensor connected to the SensorDAQ interface. I can see installed SensorDAQ in NI MAX, but i really dont know how to get data from sensor to LabView by using DAQ assistant. (there is no option for blood pressure measuring and other measurement types from data acquire doesn't work)
Does someone have any idea or knows any way to get data do my pc?
Thanks for any help.
I'm attaching pictures with measurement types and self-test of SensorDAQ in NI MAX.
Solved!
Go to Solution.

I have labview 2013 version.

Acquiring pressure data using daq assist

Similar Messages

Maybe you are looking for