Adding AEBS Dual-Band to home network

I'm looking for advice on the best way to add an AEBS Dual-Band to my home network. Here's my current setup:
DSL --> Actiontec GT724 modem/router --> Gigabit switch --> 2 Macs, 1 PC, 1 AppleTV, AEBS
On the AEBS I have the Internet Connection Sharing set to "Off (Bridge Mode)".
The problem I have with this setup is that I can't take advantage of the "Guest Network" feature of the new AEBS.
If I change the Internet Connect Sharing to "Distribute a range of IP addresses" will I need to disable the DHCP server on the DSL modem/router?
Do I need to physically move the AEBS between the DSL modem/router and my gigabit switch?

I agree with the recommendation to put the AEBS directly after the DSL. You may have to change the DSL to Bridge mode instead of simply turning off DHCP. Your ISP should be able to help you with that.
Your requirement for a second Ethernet cable can be eliminated with a pair of Ethernet splitters as you only need 4 of the 8 wires already run upstairs. This will allow your outside WAN to come up and then return your inside LAN to go down to the switch.
http://www.cablesunlimited.com/products/Prod_Individual3.aspx?groupcode=I2981

Similar Messages

How to set up AEBS dual band as single network?

As I have it now, when I open Network Prefs and click on Advanced, I see two networks listed: my 5GHz network and presumably, my 2.4GHz nbetwork. The problem is that although I've listed my 5GHz network as my preferred network, it continually chooses the 2.4GHz network? Or that is what I see when I cherck my wi-ifi status in my menu bar. I'm not sure why that is, but I've read that if I create a single network, my AEBS will automatically choose the appropriate network? If this is so, I'ds like to eliminate ther 2.4GHz network.

so I thought if I was able to merge both bands, then I could eliminate this happening?
You cannot "merge" both bands....they will always be separate signals....but you can assign the same wireless network name to both bands. That is the default setup for the AEBS, and the setting that most users should use.
Your Mac will connect to either the 2.4 GHz or 5 GHz band automatically.
Your Mac will connect to the band that it thinks is the best quality.
Best "quality" does not necessarily mean the faster speed band. The Mac is looking for the best combination of speed, signal strength, low noise, interference and other things that Apple engineers won't tell us about.
Try removing the check mark in the box next to 5 GHz network name in AirPort Utility and test things out. You may find them better, or worse.

I have an iMac OS X. I added it to a pc home network. On the network I have a Canon MP810 printer. I can get my iMac to print a test page, but it not print anything else. How can I fix this problem?

I have a iMac OS X. I added it to a pc home network. On the network I have a Canon MP810 printer. I can print a test page on the printer sent from the iMac, but that is the only thing that can be printed from the iMac. What do I need to do the solve this problem?

Try installing the printer via System preferences using this driver:
http://software.canon-europe.com/software/0025024.asp?model=

Adding new dual band AEBS-initial setup question--join network or setup new

Upon the initial setup of a new dual band AEBS, do I join my current network or setup a new network?
I bought this just so I can set up a separate 5GHz band to force my newer computers to a faster network. I know that the 5GHz band needs it's own new network name. I am just wondering how to do it at the very beginning after I plug it in. I want the 2.4GHz band to connect on the network I already have, and the 5GHz band to be a new name.
Thanks!

Looks like Bob has already given you the correct steps. In addition to his comments, I would like to offer the following suggestions:
o Before trying to configure either base station to extend your new DB AEBSn, I would strongly suggest that you perform a "hard" reset on the AEBSn & a "factory default" reset on the AXn.
o Place the base stations within near proximity of each other during the set up phase, and then relocate them to their desired locations when complete. To make it even simpler and avoid having to "switch" wireless networks during the setup, attach each to the DB AEBSn via Ethernet.
o Remember each base station will only be able to extend one of the DB AEBSn's radios so try to select the appropriate base station for the job.
o I would recommend the following radio mode combination for your DB AEBS: 802.11n only (5 GHz) - 802.11b/g/n. This will prevent any 'stray' 802.11a wireless clients from connecting to the 5 GHz network and affecting its overall bandwidth performance.

Adding Wireless-N-ONLY Time Capsule to Dual-Band Airport Extreme Network?

I have a dual-band airport extreme which I have configured to create both a wireless-a/b/g/n SSID on my network, as well as a second SSID which is Wireless-N-ONLY (meant to be used with my Time Capsule so that all backups to the Time Capsule via Time Machine are only ever done via Wireless-N).
My Airport Extreme is already configured, and now I just have to configure my Time Capsule on my network...
Can someone briefly run through the "assist me" steps in the Airport Utility that I'd want to follow to configure my Time Capsule so that it's available on my dual-band base station's wireless-N-ONLY network and so that it's not transmitting or receiving any other wireless protocol other than wireless-N?
Thanks!

Hi Bob,
Thanks for your earlier feedback. I now have a dual band TC and the previous dual band EABS and I'm tearing my hair out trying to get these things to play nice! Maybe you can provide some assistance:
1) The TC upstairs is connected to the comcast modem and is the main 'router' in my network. In addition, I'm using the "create wireless network" option on this router to set up both a 2.4 GHz and 5.0 GHz wireless environment.
2) The AEBS downstairs on the opposite end of the house is connected by ethernet - whole house is wired so I'm feeding from the TC upstairs through a switch in the disti box down to an outlet where I have the AEBS. The cat-5 cable is connected to a LAN port on the back of the AEBS.
3) I have the AEBS set up to extend the wireless network. When I do this it only gives me the ability to select one wireless network (I have the TC configured to call the 5 GHz network something different) - In essence doesn't appear to want to let me extend both bands of the wireless network.
The problem seems to be that once I get all the configurations set I have no connectivity and if I try to open the configuration via Airport Utility, its just a spinning gear and will never open to show the settings. This happens to with both the TC and the AEBS. It's like it's in a loop or something.
I immediately disconnect the AEBS from the network and suddenly all is well again.
I know this seems like a rant, but this has been kicking my a** for two days!! I've just about had it with the constant 'hard reset' of the routers and starting over with configuration. If you have any specific things I should do, or settings that are key to set up both devices to extend my wireless network throughout the house I would be so thankful!!
Thanks,
Don

New AE-Use as extender AND utilize dual-band or guest network?

I currently have a 1st Gen Time Capsule hooked into my only cable modem. However, the signal is very weak on the 2nd floor of my house. I've been thinking about getting an Airport Express to extend my network so that I have improved coverage upstairs.
Now it appears that the new Express supports the dual-band and the guest network that my original 1st gen TC does not. If I purchase it to extend my network, can I also use these features or would it have to be the first device in the network (hooked into the cable modem?

If I purchase it to extend my network, can I also use these features or would it have to be the first device in the network (hooked into the cable modem?
Unfortunately, your Time Capsule is not a simultaneous dual band model, so the "new" AirPort Express would only extend one band....just like the "old" AirPort Express would do.
Maybe Apple has a deal on refurbished or close out "old" Express devices that might help you.
Otherwise, you would need to connect the "new" AirPort Express to the cable modem to get the benefits of a "main" and "guest" network. The "guest" network cannot be extended, by the way. It is only produced by the "main" AirPort connected to the modem.

Adding new Computer to my Home Network and I have a WRT54GS .V5 Router

I have a existing home network connecting a HP laptop and a Dell desktop and all is well. Now however I bought a new Lenovo laptop with the Vista OS with SP1 and I would like to connect it to my home existing home network. I know this might be a rather simple question BUT I am not great with networks and I set up my home network years ago and I draw a blank on how I did it. There is one CD I found that I marked with the words Remote Linksys Install on it and there is one file on it named NetSetClient. Not sure why I kept it and I do not remember what it does but might help in getting my solution.
Please help the network novice

As your linksys router is configured and its working on 2 other computers perfectly fine, so you dont have to run the CD again on your new computer. Is your new computer is a Wireless computer, So on your New computer, in the system tray, Right click on Two computer Icon and select "Connect to a Network".. selecte your Wireless network... type in your security key and click on Connect. After this try going online.
If you new computer is a Wired computer, Just plug in the cable from your New computer to the Router and you will be able to go Online.

Adding wireless router to wired home network

I have a home network consisting of two PC's which share a satellite internet connection via a wired BEFSX41 router.   The PC's and router/satellite modem are in three separate rooms connected by Cat5e cable.
Now I want to add a new laptop (third PC) to my network using a WRT54G router and a WPC54G notebook adapter.  I just ran the WRT54G wizard and it makes no sense for my configuration.
Should I connect the WRT54G's internet port to a spare port on the wired router, then power up wired, wireless routers and the modem in sequence?   Then run the program at the final step of the wizard one of my original PC's? Any help will be appreciated.

Cleck this link out. The only thing I would do is make sure you connect the cable from a numberd port to ort number 1 on the wireless router and set up the SSID and wireless security. Make sure you have the latest firmware on the wireless router because in this configuration you will not be able to access its user interface.
http://linksys.custhelp.com/cgi-bin/linksys.cfg/php/enduser/std_adp.php?p_faqid=3733&lid=3726837401B...
Message Edited by Ikester on 07-09-2007 11:44 AM
Richard Aichner (Ikester)

Dual Monitor Setup/Home Network/Sync--11" MBA & 21.5" iMac via Thuderbolt cable?

11" MBA & 21.5" iMac both purchased in August 2011 running Lion
Is it possible to setup my MBA & iMac where they will sync? I have them connected via thinderbolt and want to be able to connect when I get home and sync all my folders [notes, cases, papers, etc...]?
If this is not possible is there a way to transfer files between my two machines using the Thunderbolt cable? I ask because even though my MBA has a Thunderbolt port, there is not "Fire Wire" option under "System Preferences →Network" like there is on my iMac?
In a perfect world I want to be able to hook up my MBA & iMac via Thunderbolt cable, have them both controlled by my Magic Mouse & Keyboard I use with my iMac as dual monitors and be able to transfer files back and forth freely. I understand this may be a lot to ask but thought I should throw it out there just in case there was a way and I was not doing something right.
I appreciate all the help by everyone in the Apple Commun ity

OK great info!
I found 2 possible ethernet to USB adapters:
By "Plugable": USB 2.0 to ethernet LAN wired network adapter - seems this will work, but I'll contact Plugable.
2. Apple USB Ethernet Adapter
Easily connect your MacBook Air computer to an Ethernet network with the Apple USB Ethernet Adapter. Small and light, it connects to the USB 2.0 port of your MacBook Air and provides an RJ-45 connector that supports 10/100BASE-T performance. BUT NOT SURE IF THIS WILL WORK ON ANYTHING BUT a MacBook Air…
One person commented:
This little gem used to be the device of choice for adding a second Ethernet interface to a Mac Mini Server and I'd been using one that way for about a year. After doing a software update to 10.6.6 it stopped working. Forewarned is forearmed – it appears that Apple is finally enforcing the MacBook Air system requirement.
Thanks for any additional comments.
Best regards,
Steve Schulte
Sunday 6 January 2013

AEBS Dual Band - weird connectionspeeds

Hi folks, hi Apple,
got the new dualband AEBS and I am experiencing following problem(s):
When I set my AEBS wireless setting to automatic, networkutility reports an connectionspeed of 130mbit/s, but when ich trie ro change the setting I get some strange results.
Restarted the AEBS with the setting "N Only 5GHz - b/g " -> 300Mbit/s
Disconnected my MBP and reconnected it -> 54Mbit/s
Restarted the AEBS with the setting "N Only 5GHz - N only 2,4GHz " -> 300Mbit/s
Disconnected my MBP and reconnected it -> 300Mbit/s
(obviously my iphone can't connect)
Restarted the AEBS with the setting "a/n - g only " -> 300Mbit/s
Disconnected my MBP and reconnected it -> 54Mbit/s
Am I doing something wrong or can anyone confirm this?
And by the way, when I trie to play a homemovie which is stored on my airdisk it now stutters this didn't happen with my previous AEBS... In iStatpro it seems that the connection breaks down vom 5mb/s to 0kb/s every few seconds and gets immediately up again.
and my bootcamp xp installation also can't connect to the dualband network, just to the guestnetwork I set up...
Help would be appreciated!
P.S. Sorry if I made any mistakes, english is not my first language.
Greetings
Dave

Thanks for your post!
The video playback stutters with N 5Ghz 300mbit/s, N 2,4GHz 130mbit/s and G 54mbit/s.
What I also noticed on every band and connections speed:
When I copy a file from my airdisk to my MacBook, iStat pro shows my the incoming speed and it goes something like this:
3mb/s, 4mb/s, 0kb/s, 3mb/s, 4mb/s, 0kb/s, 3mb/s, 4mb/s, 0kb/s and so on.
So it seems that the connection breaks down and goes up right after that.
I think this why the movie stutters and why the speed isn't what it should be...

Dual Band Time Capsule - networking issues

I upgraded from an original Time Capsule that had been running successfully on the 5Ghz band with firmware 7.4.1.
I changed my original TC out and setup everything from scratch so that the DB TC was connected to my cable modem and provided the DHCP leases. Set it to provide N only services on 5Ghz and b/g on 2.4 (I tried the automatic and the manual settings during troubleshooting). Guest networking was turned on and was serving up on the 2.4Ghz channel.
Next I moved my original TC to another room, extended the new DB TC on the 5Ghz network and everything seemed fine.
But then I noticed that whenever I started to run a TM backup (over airport or wireless) that eventually my original TC would seem to go deaf. I could not access the internet through it. However, Airport utility could still see it. On further examination I realized it had lost its IPv4 DHCP address and was only displaying an IPv6 address in the Airport Utility.
After many isolation steps and no success, I decided to move the old TC into the same room as the new DB, connect them via ethernet and turn off the wireless on my old TC altogether to prevent interference. That seemed to work. Until a TM backup was kicked off (btw - all backups right now are to the original TC not the new DB).
Finally, I disconnected the original TC altogether and just let the DB TC run everything (but still I was not backing up to it). Now the new TC by itself seems to stop allowing access to the internet. Internal network is fine. What is really odd, is that rebooting the DB TC sometimes doesn't seem to help. However, reseting the cable modem does (for a little while).
I switched back to my original TC now and everything is working flawlessly again including being able to run TM backups to it and no loss of internet access.
Any ideas? I have already exchanged it once. I have reloaded firmware (7.4.1). I have set up everything from scratch. And still it is really flaky.
Thanks in advance.

5 GHz signals are capable of faster speeds, but you always have to give up something to gain something else. In the case of 5 GHz, in order to gain higher speed, you must give up distance and penetration power with 5 GHz.
Bottom line...5 GHz signals are significantly weaker than 2.4 GHz signals. Your Mac is looking for the strongest, best quality signal, so it connects to the stronger 2.4 GHz band at the upstairs location.
For most of us, 5 GHz is pretty much of a line-of-sight deal. If your Mac has a clear look at the Time Capsule, and it is relatively close to the Time Capsule, it will likely connect to 5 GHz.
Otherwise, if the signal must pass through a few walls, or a ceiling (which is much thicker than a wall) the Mac is very likely going to connect at 2.4 GHz.
If you take the Mac downstairs and give it a clear look at the Time Capsule from 10-15 feet or so, does it connect at 5 GHz?

New Airport extreme dual band and older version.

I purchased a new dual band Airport Extreme base station.
How can I make use of an older version of the Airport Extreme 802.11n (non dual band) in my network?
Can I hook the 2 up together to boost up the range or coverage of the network?
If so, how far apart do they have to be?
Also, does the main AEBS have to be as close possible to the modem in order to work better? my modem is in the basement in the mecanical room. What would be the best to get the best signal througout my house?

Hello mike1970. Welcome to the Apple Discussions!
How can I make use of an older version of the Airport Extreme 802.11n (non dual band) in my network?
Two examples would be: 1) Connect the old AEBSn to the new one by Ethernet, and then, configure them for a "roaming" network. In this type of network allow you to roam with a portable wireless device and still be on the "same" network, and 2) Configure the old AEBSn to extend the wireless range of the newer one in what is called a dynamic WDS. The major difference between a WDS and the roaming configuration is that the two base stations would not need to be interconnected by Ethernet.
Can I hook the 2 up together to boost up the range or coverage of the network?
Yes, both only one of the newer AEBSn's wireless radios. Most likely, it would need to be the 2.4 GHz radio as the signal can travel farther and not be impacted by objects ... like walls.
If so, how far apart do they have to be?
That would depend on what would be between them. In a room with no Wi-Fi obstacles, you could probably place the second AEBSn 50-75 feet away to boost the signal another 50-75 feet.
Also, does the main AEBS have to be as close possible to the modem in order to work better?
No.
my modem is in the basement in the mecanical room. What would be the best to get the best signal througout my house?
The best way would be to have the house wired for Ethernet, and then, place a Wireless Access Point (WAP) at each location that you would want wireless coverage.

Creating a Dual Band Network

I have the newer Airport Extreme Base Station, with N capability, before it supported Dual Band. I also have an Airport Express. What I want to do is broadcast a network in my home with 5GHz for my Macbooks and a second network on the AE at 2.4GHz for everything else. I've tried many times to get this to work, and I keep getting the error message that the DHCP overlaps with the AEBS. What should I do? I know this can work somehow.

Hello Rad Mac. Welcome to the Apple Discussions!
Setting up a "dual band" network is described in the Designing AirPort Networks document, starting on page 48. Please check out the document and post back if you still have any questions.

Setting up/extending a Dual Band network

Any recommendations regarding dual-band vs. the n/b/g blended network? Is it possible to set up a dual-band network on an AEBS-n and also boost the "n" side of the network with an AX-n? I've searched the discussions but have not found much on the topic, other than some comments regarding iMacs not liking "n" or 10.5.3 or airport utility 5.3.1 or maybe the "automatic" channel setting or possibly something else.....
A little history:
We have 3 iMacs (new 3.06 Ghz, 17" late 2006, 20" late 2006), 3 MacBook Pros, and one dual-2.5 Ghz G5 that all shared internet access through a Motorola modem/Comcast cable via an Airport Extreme Base Station b/g. The AEBS was in the basement and configured as a WDS with an Airport Express b/g that served to extend the network's reach to the second floor and remodeled kitchen (new steel beams). This setup has worked nearly flawlessly for years until recently, when both of the older iMacs started experiencing intermittent airport signal drops--supremely annoying. The modem seemed to work fine, however, and the AEBS light stayed green and the G5 and MBPs weren't having issues (some running Tiger, some Leopard).
I thought that upgrading to Leopard (erase and install) might take are of any weird settings or corrupt files and thus improve the iMacs' airport connections, so I upgraded the first one, and it seemed to fix the problem--no drops of airport or internet for several hours. I then decided it was time to upgrade the network as well--swapping out the old b/g AEBS and AX for a new AEBS-n and AX-n. (Yes, I know, not too smart to change both the OS and the network at the same time ... but here we are.) Since the G5 in the basement can't connect to an "n" network, I decided to set up a Dual Band network with the AX-n acting as the old AX b/g had to extend the network.
This is what it looked like:
cable modem ------>
AEBS-n ------> wireless to Airport Extreme-n ---> wireless to older iMacs and MBPs
AX b/g (connected via ethernet to AEBS) -----> wireless to the G5
This worked, sort of, in that all but the G5 could all pick up and join either the "n" or the b/g network. Problem was, the network was very unstable-- the airport signal would suddenly drop out for no reason then recover, or the airport icon would show a full 4 bars but have no internet connection. This was happening on all of the macs, perhaps more so on the two older iMacs, while the modem itself showed no change in status, and the AEBS-n light would remain green. When I removed the AX-N from the setup to see if that was causing a hiccup, the drops were a little less frequent but the kitchen iMac was marooned with 1, maybe 2 bars in the airport icon and the signal strength on the second floor was decreased. Oh, and the drops continued to happen. I've now reverted to a b/g-compatible network, which is better, but still hasn't prevented all of the drops.
My questions are:
1-Any ideas about why the airport is acting wonky? Are 'n' networks proving to be more problematic than the old ones?
2-Is it possible to use an AX-n to extend the range of the "n" side of a dual band network?
2-If so, any ideas for improving the network's reliability?
3-If not, will going back to a b/g-compatible network negate the supposed speed benefits of 802.11n? Would I go back to using a WDS setup then?
I've tried so many different settings, combinations, configurations trying to get this up and working, that I'm ready to pull my hair out. Any help will be greatly appreciated!
Message was edited by: wiswic

Thanks for your reply. Looking back at my sorry attempt at a diagram, I realize I wasn't clear about a couple of things. The modem is connected via ethernet to the AEBS-n. The AEBS-n is connected via ethernet to the AE-b/g, which provides wireless coverage to the G5 and others. So far, everything is in the basement.
We live in an old house--no way to set up the network via ethernet--and so rely on the airport network to provide internet access to the computers on the first and second floors. In our old network, I had an AE-b/g as a WDS remote located in the kitchen that provided the first and second floors with their internet connection.
When I upgraded our network, I set up the new AEBS-n as a 5.0 Ghz an-only network (create a network/allow network to be extended) and connected the old AE b/g to it (bridge mode/create a network) to provide wireless internet for the G5. The iMac in the kitchen could hardly pick up the "n" signal at all, and it could receive only a weak signal from the b/g network. Lots of dropped airport signals and also lots of dropped internet connections. Strangely enough, the MacBookPros on the second floor could pick up both signals pretty strongly, but they, too, had lots of drops. The 2nd floor iMac was even worse than the kitchen iMac--spotty reception at best, and lots of drops. The G5 and the iMac in the basement, meanwhile, were fine--strong signal and only intermittent drops.
Hoping to extend the reach of the "n" network and thereby eliminate the drops, I added an AE-n to it (bridge mode/extend the network) and put it where the old b/g had been. This boosted the "n" signal to the kitchen and 2nd floor, but the drops seemed to become more frequent and for longer durations. Perhaps this was merely coincidence, but it made me question whether adding the AE-n in a dual-band network was advisable. Not finding any info that specifically addressed that scenario, I turned to the discussion forum for guidance.
Further research leads me to believe that the iMacs' issues may be more due to their being iMacs in the first place, but I was still left with a very unreliable dual band network for the rest of the Macs. Reconfiguring the AEBS-n and AE-n as an n (b/g compatible) network has led to far fewer drops, but like you, I'd prefer to keep my "an" devices separated from the G5 to make use of their higher wireless speed.
So....I guess what I need to know is whether anyone else been having so many dual band dropouts? Have you had any success in eliminating them? Have you successfully extended the "n" side of their dual band without adversely affecting stability?
As long as I know this isn't a lost cause, I'll give it another go and keep tweaking settings in hopes of finding a stable setup....

Wifi connectivity - Yosemite and dual band routers (i.e. BT Home Hub)

This is working for me so far after all previous tips on other Discussions proved only to be temporary. This is the only one that enabled my MBP to accept password for the SSID.
From BT Home Hub - 2011!!
The BT Home Hub 4 and Hub 5 are dual band with two wireless frequencies for devices to connect to: 2.4GHz and 5GHz. On both Hubs, the default setting has the same network name (or SSID) for both the 2.4GHz and 5GHz bands. Connecting a typical 5GHz-capable device to this single SSID will automatically connect the device to both the 2.4 and 5Ghz frequency at the same time.
However, not all dual band devices behave the same way and some device software does not cope well with a single SSID for both frequencies.
As a result:
the device may not connect wirelessly to the Hub
it may not connect to 5GHz frequency even in the same room
the wireless connection might be intermittent
the wireless connection might be very slow
Devices where there are known to be problems include:
Some Apple devices including iPhone 5 and Apple TV
some Android smartphones
Xbox
For some devices you can solve this problem by having different network names (SSIDs) for the 2.4GHz and the 5GHz bands. To set this up, follow these steps:
Open your web browser on a device connected to the Hub and go to bthomehub.home. This will open the Hub Manager
Click on Advanced Settings and enter your Hub admin password when prompted. Unless you've changed it, you'll find the default Hub password on the Hub settings card
Click on Continue to Advanced Settings
Click on Wireless
Click on 5GHz
Change 'Sync with 2.4 Ghz' to No
Change the 'Wireless SSID' to a new name (we recommend just adding '5GHz' to the end of the existing SSID name so you'll know which one is which)
Click Apply to save the changes
After a few minutes you should see two BT Home Hub SSIDs in the list of networks on your device. All of your devices will still automatically connect to the original SSID name, which will be the 2.4GHz.
If you have existing dual band devices you want to connect to 5GHz only, you'll need to connect them to the 5GHz SSID that you've renamed. AND RESTART the hub - PJ
Note- Even though wireless speeds at 5GHz can be significantly faster than 2.4GHz, the range of a 5GHz connection is not as good. As a result, you may need your device closer to your Hub (than you'd need to when using the 2.4GHz SSID) to get the best performance possible."

Sadly it didn't last...
I just posted this on BT Home Hub users forum. and the big Yosemite/wifi Discussion
"Sorry to awaken this topic from the dead....
I am using HH5a, opted in to FON, and Os10.10 MacBookPro
I have no problem whatsoever connecting and staying connected to 2.4ghz
I struggle since OS10.10 to either connect or stay connected to 5ghz
A persistent issue with trying to connect to 5ghz is the response "invalid password" Only occasionally in the past 3 months has this not been a problem
the app WifiExplorer shows today that the only other networks on the same channels as my networks are the FON wifiX - both of which I presume are using my router/wifi as when I manually change channels these move with me.
Signal strength on 2.4 ghz is between 77 - 85, 5ghz 80+/- 1
Noise and signal noise ratio a lot higher on 2.4 than 5
(There is lots more info on wifi explorer but I dont know its relevance/meaning)
I have tried using manual channel selection and Smart Wireless and can't see much difference in 5ghz connection
Given a choice I would prefer to stay in FON but if there is overwhleming evidence that these hot spot networks are affecting mine, I would consider opting out. Views/ guidance please. Thanks. And a Happy New Year too."
IS ANYBODY ELSE using BT Home Hub5a having this same issue? I BELIEVE it has largely if only been since upgrading to 10.10.1 but can't swear to it.
IS IT SIGNIFICANT THAT SOMETIMES THE PASSWORD TO 5GHZ network is accepted and other times not?

Adding AEBS Dual-Band to home network

Similar Messages

Maybe you are looking for