ADF disclosure action listener not triggered when set disclosed directly

ADF disclosure action listener not triggered when set disclosed directly in code.
Is this expected behaviour?
Thanks

This should be the expected behaviour as there is no client side event fired.
You would need to queue a Disclosure Event programmatically if you need to call the disclosureListener through code,

Similar Messages

CSCun15879 - CAT4K MAB not triggered when "authentication control-direction in"

Dear all,
We try to get WOL working in combination with MAB authentication and we think the implementation of "authentication control-direction in" is broken on the Cat4k5 platform and is working on the Cat3850.
We run exact the same config on a Cat3850 and "authentication control-direction in" and MAB+WOL works fine.
My question: Can other users confirm this BUG?
So "authentication control-direction in" breaks MAB on:
Chassis Type : WS-C4507R+E
Power consumed by backplane : 40 Watts
Mod Ports Card Type                              Model              Serial No.
---+-----+--------------------------------------+------------------+-----------
1    48 10/100/1000BaseT Premium POE E Series WS-X4648-RJ45V+E   JAE18280xx
2    48 10/100/1000BaseT Premium POE E Series WS-X4648-RJ45V+E   JAE18280xx
3     6 Sup 7L-E 10GE (SFP+), 1000BaseX (SFP) WS-X45-SUP7L-E     CAT1827Lxx
5    48 10/100/1000BaseT Premium POE E Series WS-X4648-RJ45V+E   JAE18270xx
6    48 10/100/1000BaseT Premium POE E Series WS-X4648-RJ45V+E   JAE18270xx
7    48 10/100/1000BaseT Premium POE E Series WS-X4648-RJ45V+E   JAE18280xx
Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSALK9-M), Version 03.05.03.E RELEASE SOFTWARE (fc1)
cat4500e-universalk9.SPA.03.05.03.E.152-1.E3.bin
And "authentication control-direction in" and MAB works fine on:
Switch Ports    Model                Serial No.   MAC address     Hw Ver.       Sw Ver.
1       56     WS-C3850-48P          FCWxxxx ccd8.c130.aaaa M0            03.03.03SE
Cisco IOS Software, IOS-XE Software, Catalyst L3 Switch Software (CAT3K_CAA-UNIVERSALK9-M), Version 03.03.03SE RELEASE SOFTWARE (fc2)
cat3k_caa-universalk9.SPA.03.03.03.SE.150-1.EZ3.bin
Kind regards,
Paul Boot.
Reinier de Graaf Hospital,
The Netherlands.

Hello Kashish-
Can you:
1. Post the full switchport config
2. Make and model of the switch
3. Version of code running on the switch

BSEG.CREATED event not triggering when a document is posted in FB60

Hi All,
I have a requirement in which i need to post documents in FB60/FB65/FB01 tcode. But when i post the document in FB60 the event BSEG.CREATED is not triggering. I could not see any trace in SWEL. But when i park the document in FB60, FIPP.CREATED event is getting triggerd.
Can anyone tell me why this BSEG.CREATED event is not triggering.
Thanking you in advance,
satheesh.

Hi Viji,
Thanks for your quick reply.
We have maintained the required configurations in the system related to this. But still the event BSEG.CREATED is not triggering.
for this the alternative solution is to implement the BTE '1030'. But our functional team is asking us to check whey standard business object BSEG.CREATED is not triggering when we post a document. So that particular reason we are not able to find out.
Configuration maintained.
1) Created a workflow variant and assigned it to particular company code(OBWA and OBWJ).
2) Checked the 'Posting' release' and 'Release payments' checkboxes in the OBWA transaction.
3) Event linkage for BSEG is active.(SWETYPV)
Thanks,
satheesh

Workflow not triggered when i have changed the PO

Hi,
We have custom fields (Price) in PO Header as well as in item. when we update in header the price should get distributed to items.
we have custom workflow evernt (changed) to update the items if user change in header. But the issue is if user changes the items and save the po, it is not updating immediatly. after we come back to Purcahse Order and save the purcahse order again then it updates the table.
Is there any reason why the event is not triggered when the PO was changed initially.

Hello,
"We have custom fields (Price) in PO Header as well as in item. when we update in header the price should get distributed to items. "
If you update a price in the header, how/why would that be distributed to the items? Is this a total price of the whole PO? Why not just have it in the header?
"we have custom workflow evernt (changed) to update the items if user change in header."
OK. Strange, but OK.
"But the issue is if user changes the items and save the po, it is not updating immediatly"
I thought it was supposed to happen when the users changed the header, not the items.
If you really have a workflow to update the items when the header is changed, then maybe it's not succeeding if the PO items are locked, eg by having them on your screen. Did the worklow actually start? Any error messages?
rgards
Rick Bakker
hanabi technology

ChaRM: Mail not triggered when current user = mail receiver?

Dearl all:
     Ive noticed that mails are not triggered when the user who is processing a document is the same who will receive it. Is there any way to deactivate this functionality?
Thank you very much,
Federico.

Hi Miguel, how are you?
      I think it is a nice feature not sending a mail when the user who is changing the status in the one who would receive the mail in that next status. But Im in the testing pahse of implementing SOLMAN and I would like to know if this is a real feature or a flaw, and besides I would like to turn off this possible feature, just for the testing phase. This is not a big deal anyway.
    By the way, I also notice that if there is a partner assigned multiple times to a document, it doesnt trigger the mails as expected.
Best regards,
Federico.

Workflows not triggered when documents are created in Doc Set via Content Organizer

The following is my scenario:
A document set (containing several documents) is created in Library A on Site A
Using Send To, the Document Set is sent to the Drop Off Library on Site B (a different Site Collection)
A Content Organizer rule then moves the Document Set and its documents to destination Library B
In Library B I have defined a workflow (using Visual Studio 2012) that is triggered when new item is create
When the Document Set arrives in Library B from the Drop Off library (i.e. when the Content Organizer moves the Doc Set to Library B), the workflow is triggered (and executes) on the Document Set, but it is NOT triggered on the documents within the Document
Set. How can I get the workflow to trigger on the documents within the set when they are created via the Content Organizer rule?
The interesting thing is that if I manually add another document to the Document Set in Library B, the workflow is triggered on that document. It just does not trigger when the documents are created via the Content Organizer.

Hi,
In edit Content Organizer rule page, I see there is an option as Automatically create a folder for each unique value of a property:
However, unlike the drop down used in the property based filters above, this drop down *only* contains properties that are required by your content type.
This is done to prevent adding folders that have no values for a property.
If you need to put similar documents to the same folder, you could consider making use of this feature.
Regards,
Rebecca Tu
TechNet Community Support

Approval Procedure not triggered when Credit Limit Exceeded

Hi,
I've defined an approval procedure which I would like to launch when a clients Credit Limit has been exceeded. I've checked the required fields on Administration > General Settings > BP tab (credit Limit, Commitment Limit, AR Invoice, Delivery, SO). I've also checked the Activate Approval Procedures on the same tab.
I know the approval procedure has been set up the correct way, since it is launched when I change the Terms to for instance 'Total document'.
There is a system-message when I am creating a Delivery Note for a customer indicating that the credit limit for this customer has been exceeded. But still, the system allows the user to add the document without triggering the approval procedure....
What am I doing wrong?
Btw: The credit limit exceeded is in negative numbers, but I've tried both the condition 'Deviation from Credit Limit greater than 1' and Deviation from Credit Limit Less than 1...

Could you clarify what you mean by "The credit limit exceeded is in negative numbers"
Negative number: the system message I get when I create a delivery note for a customer, exceeding the credit limit is the following:
Customer has exceeded credit limit - 95.479 EUR
Customer has exceeded commitment limit - 95.479 EUR
Continue (Y/N)
Make sure the Credit Limits are set in the BP Master. --> OK, credit limit is set to 100 EUR, Commitment limit to 100 EUR
Also use Great than in Ratio and try to use a small number like 10 in the value --> I am using 1 EUR
Also, check in System Initialization > General Settings..BP Tab Activate approval procedure is checked. --> it is checked.
Using the range option does not solve the problem, in fact even if I use 'Deviation from Credit Limit does not equal 1 EUR' the approval is not triggered. When I use the same Approval template, but I alter the terms to Total document greater than 1 or Discount% greater than 1 the approval is triggered.
Edited by: Rui Pereira on Apr 29, 2009 1:19 PM

Why "Will Close" action is not triggered?

Hello
I've created a simple pdf file that should show an alert box before the document is closed. But it does not work as expected, the message is not shown.
Why is the action not triggered?
( After I added another action (before print), executed it, then the "Will Close" event is triggered when the document is being closed and the message show up. )
the same issue reported here: adobe - close document action() level in pdf javascript - Stack Overflow
Foxit reader triggers the action correctly.
Thank you

sure,
Will Close doesn't work at all:
js-onBeforeClose.pdf - Google Drive
Will Close works after the document is printed:
js-onBeforePrint-onBeforeClose.pdf - Google Drive
Thanks

Patch Policies not applying when set to Date Specific

I have been trying to use patch policies for a while but can't seem to get
them working very well. In 'Patch Policy Enforcement Settings' I have set
a schedule using 'Date Specific' and 'Process immediately'. If I check the
patch status policy I see 100 targeted/ 12 Effective/ 0 Not Effective/ 88
Pending. The 88 never move from pending even though almost all of them need
the required patches. If I set the schedule to Recurring and 'When a device
is refreshed' it basically tries to install the patches on every refresh
cycle even though the device no longer requires the patches. This happens
on every device targeted by the policy.
Digging into the actually bundle that gets created I can see in the install
actions the Install Frequency is set to 'Install always' which may explain
why it runs through each patch every refresh when it is set to install on
refresh.
The documentation on this new feature doesn't go into much detail on how
everything actually works. I would guess the correct functionality would be
once a policy is enforced on a machine it would no longer try to keep
installing the same patches from the policy since they are not needed.
Using the Enforcement by 'Date Specific' seems to be broke also.
Jim Koerner
Server - ZCM 11.3.1FTF1 and Internal Database on Win2008R2x64
Clients - ZCM 11.3.1FTF1 on Win7SP1x64

Originally Posted by Jim Koerner
Sounds just like it. Missed when I was browsing the knowledge base. doing
some more detailed searching I fount this in readme for 11.3.1 "Defects
addressed 848442 Process immediately if device unable to execute on
schedule" option doesn't work of Patch Policy Enforcement Settings. In my
case this is not fixed and I am at 11.3.1FTF1
I will have to put in a SR and see if anything has been done with it since.
Jim
"thsundel" wrote in message news:[email protected]...
Jim Koerner;2337983 Wrote:
> I have been trying to use patch policies for a while but can't seem to
> get
> them working very well. In 'Patch Policy Enforcement Settings' I have
> set
> a schedule using 'Date Specific' and 'Process immediately'. If I check
> the
> patch status policy I see 100 targeted/ 12 Effective/ 0 Not Effective/
> 88
> Pending. The 88 never move from pending even though almost all of them
> need
> the required patches. If I set the schedule to Recurring and 'When a
> device
> is refreshed' it basically tries to install the patches on every refresh
> cycle even though the device no longer requires the patches. This
> happens
> on every device targeted by the policy.
>
> Digging into the actually bundle that gets created I can see in the
> install
> actions the Install Frequency is set to 'Install always' which may
> explain
> why it runs through each patch every refresh when it is set to install
> on
> refresh.
>
> The documentation on this new feature doesn't go into much detail on how
> everything actually works. I would guess the correct functionality
> would be
> once a policy is enforced on a machine it would no longer try to keep
> installing the same patches from the policy since they are not needed.
> Using the Enforcement by 'Date Specific' seems to be broke also.
>
> Jim Koerner
> Server - ZCM 11.3.1FTF1 and Internal Database on Win2008R2x64
> Clients - ZCM 11.3.1FTF1 on Win7SP1x64
Could be this: http://www.novell.com/support/kb/doc.php?id=7015217
Thomas
thsundel
thsundel's Profile: https://forums.novell.com/member.php?userid=128
View this thread: https://forums.novell.com/showthread.php?t=480214
Yes, please do open a SR if you can..
Thomas

Re: Dynamic Action is not triggering in LSMW Recording

Hello All,
In SAP HRMS personnel actions if i do using LSMW Recording it is not triggering the dynamic actions.
Is there any mechanism to Trigger dynamic action in LSMW Recording ?
How to find the differences in process with and with out recording ?
Small help is also highly appreciated.
With Regards,
Sunil,
+91-9903695384.

Yes. Do one thing. First study the dynamic action. Try to understand what the dynamic action is doing. Is it creating data in other infotype or is it updating some other table. Once it is clear what the dynamic action is doing then you can try to implement the same logic in LSMW. In LSMW there is a provision to add more than one recording and this recording can be called based on some logic..
Thanks & Regards,
Sandip

User Exit RV60AFZZ not Triggered When Processing IDOC

Hi,
I'm writing to seek some advice on why is the user exit RV60AFZZ not getting triggered when I do a vf01 bdc inside my inbouund IDOC function module. But when I try SHDB the user exit is getting triggered normally.
Thanks,
Mawi

Hi,
Yes I'm creating invoice using delivery orders, inside the idoc function module I'm using bdc call transaction vf01 but somehow it does not trigger the user exit.
But when I do manual vf01 in sap, the user exit is getting triggered.
I cant figure out why this is the behavior of sap.
Regards,
Mawi

Change listener not notified when tree item is deselected

I'm attaching a listener to the selected index property of the tree view selection model to detect when a user selects or deselects on or more nodes in a tree, but it appears that the listener is not notified when a user deselects a node. So if a user selects two nodes and then while holding down the Ctrl key deselects one of the selected nodes the tree view control deselects the node, but the change listener is not notified. Is this is a bug or am I doing something wrong?
I’m using the GA version of JavaFX 2.1 on Windows 7.
Thanks.
Stefan
import javafx.application.Application;
import javafx.beans.value.ChangeListener;
import javafx.beans.value.ObservableValue;
import javafx.scene.Node;
import javafx.scene.Scene;
import javafx.scene.control.SelectionMode;
import javafx.scene.control.TreeItem;
import javafx.scene.control.TreeView;
import javafx.scene.image.Image;
import javafx.scene.image.ImageView;
import javafx.scene.layout.StackPane;
import javafx.stage.Stage;
public class TreeViewSample extends Application {
private final Node rootIcon = new ImageView(
new Image(getClass().getResourceAsStream("Folder.gif"))
public static void main(String[] args) {
launch(args);
@Override
public void start(Stage primaryStage)
primaryStage.setTitle("Tree View Sample");
TreeItem<String> rootItem = new TreeItem<String> ("Inbox", rootIcon);
rootItem.setExpanded(true);
for (int i = 1; i < 6; i++)
TreeItem<String> item = new TreeItem<String> ("Message" + i);
rootItem.getChildren().add(item);
TreeView<String> tree = new TreeView<String> (rootItem);
tree.getSelectionModel().setSelectionMode(SelectionMode.MULTIPLE);
tree.getSelectionModel().selectedIndexProperty().addListener(new ChangeListener<Number>()
               @Override
               public void changed(ObservableValue<? extends Number> ov, Number oldIndex, Number newIndex)
     System.out.println("selection changed");
StackPane root = new StackPane();
root.getChildren().add(tree);
primaryStage.setScene(new Scene(root, 300, 250));
primaryStage.show();
}

The selected index value does not change in those cases as it reflects the last selected index (useful for single selection). It does act wierd at is possible to have a selected index that is not actually selected (you can report a bug for that I think).
However, if you want to track the full selection, try adding a ListChangeListener to the selectedIndices of the selection model. This one does fire a change every time.

Sticky Resource Not Available when setting up sticky http-cookie

When I try to configure the sticky:
(config)# sticky http-cookie ACE-COOKIE COOKIE-STICKY
I get the error:
sticky resource not available
An L7 policy has not yet been set upâ¦ could that be the reason for this error? Or, is it because I have not setup a class resource for the sticky cookie?

Syed,
I thought it resolved it, but it really didn't.
Added the resource-class in the Admin context:
resource-class any-available
limit-resource all minimum 0.00 maximum unlimited
limit-resource sticky minimum 35.00 maximum equal-to-min
no difference.

Background does not appear when set.

Hi,
My backgrounds do not appear when I set them.
Product name: HP 1000 1408AU
I have a photo on my desktop which i would like to be et as my background image and when i right click and select 'set as background image' it does not appear, the background just stays at blank. However when i tap the windows symbol on the keyboard (which takes us to the tiles) the desktop tile has my background image i selected. But when i click the desktop tile it does not come up.
This issue has been happening for at least 3 months.
Also when i go into the control panel, and then under the 'Appearance and Personalization' label, there is the 'Change destop background'. When i click this and select my image, and then click save changes it does not appear.
Also under the same 'Appearance and Personalization' label, when i click the 'change the theme' button, it says the image i selected is set to my desktop background, but it isnt. The background on my desktop is still blank. (blank black).
Could someone please help me with this issue?
Thanks.
P.s when explaining how to fix it please give simple straight forward instructions e.g click this then that then this......
Thanks again.
below is what my background looks like (even when an image is set)
This question was solved.
View Solution.

Hi Russell
Welcome to HP Support Forums!
See if this tutorial help you:
http://www.eightforums.com/tutorials/29777-background-show-image-solid-color-windows-8-8-1-a.html
Regards
Visruth
++Please click KUDOS / White thumb to say thanks
++Please click ACCEPT AS SOLUTION to help others, find this solution faster
**I'm a Volunteer, I do not work for HP**

My voice control in imessage is not working when set in Spanish. Only writes English.

HI,
Voice control not working on Imessage when set to Spanish. Only takes dictation in English. I speak in Spanish and writes whatever in English. Have reset iphone several times as well as I message but does not fix it. Does any one know how I can solve this problem?

Voice Control in Messages means you are using Siri, which is where that feature comes from on the keyboard. What languages does it show in Settings > General > Siri > Language?

ADF disclosure action listener not triggered when set disclosed directly

Similar Messages

Maybe you are looking for