ADP and Ceridian Interfaces

I am looking for documentation on the ADP and Ceridian interfaces from Oracle. I have seen several references to this offering from Oracle but have seen no documentation on what and where these are.
Can someone point me in the right direction?
Thanks
Chris

hi Chris
You can find the ADP and Ceridian related documents in the metalink.
Or if you guys have already started the project means ADP or the Ceridian can provide you those documents
these documents or the interface are useful only if you are planning to use their middleware for the data transfer otherwise it is not going to help you out
Regards
Ramesh S

Similar Messages

How do I get the Ceridian Interface for Canadian Payroll?

Hi gurus,
We are implementting Core HRMS in Multiple Business Group. This is my question How do I get the Ceridian Interface for UK, Italy and Canadian Payroll?
with regards
Surya

Hi Robmtu,
You can find the direct download here.

Remote and local interface on same ejb 3.0 bean instance

Hi,
Is it posible to get remote and local interface on same ejb 3.0 bean instance.
For example get local interface of a bean and than pass it as remote to client.
Both interfaces must operate on same bean instance.
Thanks
Zlaja

yes. You can implement multiple interfaces on a single class, so you can add a local and a remote interface. One trick to avoid duplicate code is to simply make the remote interface extend the local interface; then you only have to add the @Remote annotation and you're done.
For example get local interface of a bean and than pass it as remote to client.You don't pass an instances to a client, a client looks up a remote instance of the bean through JNDI.

The difference between IEEE802.1Q Native VLAN sub-interface and Physical interface?

Hello
I think the following topologies are supported for Cisco Routers
And the Physical interface also can be using as Native VLAN interface right?
Topology 1.
R1 Gi0.1 ------ IEEE802.1Q Tunneling L2SW ------ Gi0 R2
R1 - configuration
interface GigabitEthernet0.1
encapsulation dot1Q 1 native
ip address 10.0.0.1 255.255.255.0
Topology 2.
R1 Gi0 ------ IEEE802.1Q Tunneling L2SW ------ Gi0 R2
interface GigabitEthernet0
ip address 10.0.0.1 255.255.255.0
And is it ok to use the physical interface and sub-interface with dynamic routing such as EIGRP or OSPF etc?
R1 Gi 0 ---- Point to Multipoint EIGRP or OSPF ---- Gi0 R2 / R3
Gi 0.20--- Point to Point EIGRP or OSPF --- Gi0.10 R4 (same VLAN-ID)
R1 - configuration
interface GigabitEthernet0
ip address 10.0.0.1 255.255.255.0
interface GigabitEthernet8.20
encapsulation dot1Q 20
ip address 20.0.0.1 255.255.255.0
Any information is very appreciated. but if there is any CCO document please let me know.
Thank you very much and regards,
Masanobu Hiyoshi

Hello,
The diagram is helpful.
If I am getting you correctly, you have three routers interconnected by a switch, and you want them to operate in a hub-and-spoke fashion even though the switch is capable of allowing direct communication between any of these routers.
Your first scenario is concerned with all three routers being in the same VLAN, and by using neighbor commands, you force these routers to establish targeted EIGRP adjacencies R1-R2 and R1-R3, with R1 being the hub.
Your second scenario is concerned with creating one VLAN per spoke, having subinterfaces for each spoke VLAN created on R1 as the router, and putting each spoke just in its own VLAN.
Your scenarios are not really concerned with the concept of native VLAN or the way it is configured, to be honest. Whether you use a native VLAN in either of your scenarios, or whether you configure the native VLAN on a subinterface or on the physical interface makes no difference. There is simply no difference to using or not using a native VLAN in any of your scenarios, and there is no difference to the native VLAN configuration being placed on a physical interface or a subinterface. It's as plain as that. Both your scenarios will work.
My personal opinion, though, is that forcing routers on a broadcast multi-access segment such as Ethernet to operate in a hub-and-spoke fashion is somewhat artificial. Why would you want to do this? Both scenarios have drawbacks: in the first scenario, you need to add a neighbor statement for each spoke to the hub, limiting the scalability. In the second scenario, you waste VLANs and IP subnets if there are many spokes. The primary question is, though: why would you want an Ethernet segment to operate as a hub-and-spoke network? Sure, these things are done but they are motivated by specific needs so I would like to know if you have any.
Even if you needed your network to operate in a hub-and-spoke mode, there are more efficient means of achieving that: Cisco switches support so-called protected ports that are prevented from talking to each other. By configuring the switch ports to spokes as protected, you will prevent the spokes from seeing each other. You would not need, then, to configure static neighbors in EIGRP, or to waste VLANs for individual spokes. What you would need to do would be deactivating the split horizon on R1's interface, and using the ip next-hop-self eigrp command on R1 to tweak the next hop information to point to R1 so that the spokes do not attempt to route packets to each other directly but rather route them over R1.
I do not believe I have seen any special CCO documents regarding the use of physical interfaces or subinterfaces for native VLAN or for your scenarios.
Best regards,
Peter

What is the diff b/w Abstract class and an interface ?

Hey
I am always confused as with this issue : diff b/w Abstract class and an interface ?
Which is more powerful in what situation.
Regards
Vinay

Hi, Don't worry I am teach you
Abstract class and Interface
An abstract class can have instance methods that implement a default behavior. An Interface can only declare constants and instance methods, but cannot implement default behavior and all methods are implicitly abstract. An interface has all public members and no implementation. An abstract class is a class which may have the usual flavors of class members (private, protected, etc.), but has some abstract methods.
Edited by SASIKUMARA
SIT INNOVATIONS- Chennai
Message was edited by:
sasikumara
Message was edited by:
sasikumara

Remote and Home interface binding to an EJB2.1/3.0 bean.

When deploying a complete ejb bean,
-What associated a bean class, within the container,
with it's home and remote interfaces?
-JBoss Application server requires that the Bean class
directly implement both interfaces.
-Assuming EJB 2.1, is this approached by
interface implementation, a naming convention,
a common location in a package/directory,
or is this put in the deployment descriptor xml file?
What is the standard approach?
Z.

If you have included the HTTP server with your 10.1.3.2 installation you could also setup a proxy/proxy-reverse setup in the portal http server for the /app08 mountpoint and point this to your 10.1.3.2 server....

Remote and Home Interfaces

Why do we need a home interface and remote interface for a ejb.
Must these interfaces be there for each ejb?

Why do we need a home interface and remote interface
for a ejb.The Home interface is like a factory for getting to your beans. The remote interface is what you use to speak "directly" to the bean. It's remote because the bean is usually on a remote server somewhere (not in the same VM as your client code). The same is true for the home interface in terms of it being remote.
The corresponding LocalHome and Local interfaces are for use when the bean in question is not remote.
Must these interfaces be there for each ejb?You need either a Home and Remote or LocalHome and Local interface for all beans except Message Driven Beans.

How to connect to third party using PI for outbound and inbound interfaces

Hello,
I have scenarios where I have data coming in from third party EDI subsystem and sent to SAP. And also from SAP to EDI subsystem. We need to send the XMLs to the EDI subsystema nd also receive XMLs.
Can someone please suggest the ways I can connect to EDI subsytem for both Outbound and Inbound interfaces.
Thanks

Hi Prabhu,
EDI file is different from the normal flat or xml file. Hope you understand the difference.
Now if your EDI subsytem has the capability of converting the xml file to edi file viceversa then create and receive the xml file from the EDI subsystem. For the xml file you may use the file adapter as an option.
If it doesnot have the capability then seeburger adapter needs to be used. This is not an inbuilt adapter. So your company needs to purchase it.
Regards,
---Satish

Bill and Routing Interface concurrent program is not processing component

Hi All,
While running Bill and Routing Interface concurrent program,not processing the component item(Line Item) from bom_inventory_comps_interface,still it show process flag as 1. where as billing item(Header Item) is successfully done..i have tried with all the option by giving component sequence id and batch id still it is not processing component item..
Is it recommendable to give bill sequence id and component sequence id in interface table using bom_inventory_component_s sequence..
I will be very pleased if i listen from u guys... Plz help me in resolving this issue..
My Header Insert Stmt..
INSERT INTO apps.bom_bill_of_mtls_interface@system_link_visma
(assembly_item_id, organization_id,
alternate_bom_designator, last_update_date,
last_updated_by, creation_date, created_by,
revision, item_number, item_description,
implementation_date, transaction_type,
process_flag, assembly_type, batch_id
VALUES (l_inv_item_id, l_org_id,
NULL, SYSDATE,
1318, SYSDATE, 1318,
l_revision, l_item_num, l_description,
SYSDATE, 'CREATE',
1, 1, 10003535
Component Insert stmt
INSERT INTO apps.bom_inventory_comps_interface@system_link_visma
(operation_seq_num, component_item_id,
item_num, basis_type, component_quantity,
auto_request_material, effectivity_date,
disable_date, planning_factor,
component_yield_factor,
enforce_int_requirements,
include_in_cost_rollup, wip_supply_type,
supply_subinventory, supply_locator_id,
check_atp, optional,
mutually_exclusive_options,
low_quantity, high_quantity,
so_basis, shipping_allowed,
include_on_ship_docs, required_to_ship,
required_for_revenue, component_remarks,
transaction_type, process_flag,
assembly_item_id, component_item_number,
batch_id,component_sequence_id
VALUES (l_operation_seq, l_comp_item_id,
cur2.item_sequence, l_basis, cur2.quantity,
l_auto_request_mtls, cur2.from_date,
cur2.TO_DATE, cur2.planning_factor,
cur2.yield_factor,
l_enforce_int_requirements,
l_include_in_cost_rollup, l_supply_type,
l_supply_subinventory, NULL,
l_check_atp, l_optional,
l_mutually_exclusive_options,
cur2.minimum_quantity, cur2.maximum_quantity,
l_sale_order_basis, l_shippable_flag,
l_include_on_ship_docs, l_required_to_ship,
l_required_for_revenue, cur2.comments,
'CREATE', 1,
l_inv_item_id, l_comp_item_num,
10003535,apps.bom_inventory_components_s.nextval@system_link_visma
For Subcomponent Insert Stmt
INSERT INTO apps.bom_sub_comps_interface@system_link_visma
(substitute_component_id,
substitute_item_quantity,
assembly_item_id, component_item_id,
operation_seq_num, organization_id,
substitute_comp_number,
component_item_number,
assembly_item_number,
transaction_type, process_flag,
enforce_int_requirements,
effectivity_date,component_sequence_id,batch_id
VALUES (l_sub_comp_item_id,
cur3.quantity,
l_inv_item_id, l_comp_item_id,
cur2.operation_sequence, l_org_id,
l_sub_comp_item_num,
l_comp_item_num,
l_item_num,
'CREATE', 1,
l_enforce_int_requirements,
SYSDATE,apps.bom_inventory_components_s.currval@system_link_visma,10003535
Thanks
Raman Sharma
Edited by: 929841 on May 4, 2012 12:28 AM
Edited by: 929841 on May 4, 2012 2:58 AM

You need to populate the organization_id or organization_code in bom_inventory_comps_interface.
Here is a minimal insert
INSERT INTO bom.bom_inventory_comps_interface
            (operation_seq_num, last_update_date, last_updated_by,
             creation_date, created_by, process_flag, transaction_type,
             bom_item_type,
             effectivity_date, organization_code, assembly_item_number,
             item_num, component_item_number, component_quantity
     VALUES (1                                                   -- op_seq_num
             ,SYSDATE, 1433
             ,SYSDATE, 1433, 1                                  -- process_flag
             ,'Create',
             4 -- bom_item_type 1 Model; 2 Option class; 3 Planning; 4 Standard; 5 Product family
             ,SYSDATE - 1, 'PUB', 'SSGPARENT1'          -- assembly_item_number
             ,10                                                     --item_num
             , 'SSGCOMP1'                           -- component_item_number
             , 10                                          --qty
            )Sandeep Gandhi

Difference between abstract interface and normal interface

Hello Friends,
What is the Difference between abstract interface and normal interface?....

What is the Difference between abstract interface and
normal interface?....The difference is that you didn't follow convention in the first case. All interfaces are implicitly abstract so you don't have to declare them as such.

Does 2 firewire audio and video interface can work together on FCP ?

hello,
My audio interface is a TC Electronic Konnekt 24D
my video interface is a Canopus ADVC 110
my hard drives are plugged in firewire too
and I use Final Cut Pro 5.0.4
So, the konnekt is recognized by FCP only when the Canopus is not plugged. And even then, the audio sometimes drop out and sometimes causes the app to crash, so that I have to trash the preferences
When I plug the Canopus, the Konnekt 24D is recognised by OS X but not FCP
I want to use the voice over tool with the konnekt 24D, so what should I do ?
Does 2 firewire audio and video interface can work together ?
If so, maybe I only have a driver problem from TC Electronic.
But if not, I have to change this interface. Let me know if only RME, MOTU, Presonus and Edirol work, as it is said on apple's webpage for hardware compatibility
thanks
eMac G4 1,25 Ghz Mac OS X (10.3.9)
eMac G4 1,25 Ghz 1 Go RAM DDR Mac OS X (10.3.9)

The 1082 does show up as a possible input when I open
the VO tool.
Ok. So an audio interface can be plugged to FCP without crashing the app. Because of the Konnekt driver problem, I wasn't shure of this.
I use my Aja box for export & external monitoring.
All my audio sources run back into the Tascam and I
use the analog mixer in the 1082 to monitor different
sources.
When I view external video, the audio follows it to
keep sync.
that's exactly what I want with other I/O interfaces. I'd like to monitor video with the canopus ADVC 110, and monitor audio with the Konnekt 24D (or another interface if this one is not compatible)
I also imput dailies with a deck or a camera (DV or HDV) but that's not the point here.
I want to imput audio with the Konnekt 24D because of its audio quality. Not audio sync to video dailies. But voice over, in sync with FCP video playback (for me, tha ADVC 110)

PI 7.1 Sender Interface and Receiver Interface gets interchanged

Hi All,
I m facing a strange problem in PI 7.1
For many of my scenarios, the Sender Interface, sender namespace and receiver Interface, receiver namespace information gets interchanged and displayed incorrectly.
But sometimes its working fine.
When we analysed the Log messages, found that, after xml validation step, the sender and reciever interface gets interchanged.
Any idea why this happens?
How to rectify this error?

Aarthi,
Please check your message interfaces once again. Sender is outbound and Receiver is inbound.
Also please check your receiver determination.
Regards,
---Satish

I am considering buying a new MAC laptop to run LOGIC for composition and band live/recording, but which one is best as I do not want to spend too much money? Does it have a line in and how do you monitor sound? Will I need adaptors and a interface?

Can anybody help?
I am considering buying a new MAC laptop to run LOGIC for composition and band live/recording, but which one is best as I do not want to spend too much money?
Does it have a line in and how do you monitor sound?
Will I need adaptors and an interface?
Also, I am guessing as Logic only runs on MAC surely then they would not the best spec to recommend to run it?
I see all the upgrades as additional memory or a faster process?
Is a retina screen necessary, and why flash based storage against a 1TB hard drive, and a i5 instead of an i7
The main reason for this purchase is to play live and use backing tracks and record found sounds and make creative songs.
I hope you can provide some valuable feedback, as I am a longtime MAC user and see upgrades and changes happen regularly but the most important thing is the songs not the equipment.
I have £500 already and willing to add another 500 to 700 pounds, then software extra.

Can anybody help?
I am considering buying a new MAC laptop to run LOGIC for composition and band live/recording, but which one is best as I do not want to spend too much money?
Does it have a line in and how do you monitor sound?
Will I need adaptors and an interface?
Also, I am guessing as Logic only runs on MAC surely then they would not the best spec to recommend to run it?
I see all the upgrades as additional memory or a faster process?
Is a retina screen necessary, and why flash based storage against a 1TB hard drive, and a i5 instead of an i7
The main reason for this purchase is to play live and use backing tracks and record found sounds and make creative songs.
I hope you can provide some valuable feedback, as I am a longtime MAC user and see upgrades and changes happen regularly but the most important thing is the songs not the equipment.
I have £500 already and willing to add another 500 to 700 pounds, then software extra.

Flex Application architecture with web and air interface both using common components.

We have a flex based e-learning application. It uses HTTP REST service and webservice to communicate with ASP.Net application to fetch and store data.
We now want to develop an adobe air version of the user interface, which the students can download on their desktop as well as mobiles (Android, others).
What would be a good architecture for such an application which has both web and windows interface. I can see that we can reuse almost 80% of the code of our web version. But I do not want to copy and create a new windows app from the flex web app. I would want to have both co-exist.
Let me know a good article that I can read on this.

I dug deeper and found the concept of Shared Common Library. I am trying to implement that.

Code to retrive the sender and receiver interface names using custome adapter module

Hello Team,
I want to develop an custom adapter module which could retrieve the names of the sender and receiver interfaces of the scenario and for that i am trying to use com.sap.aii.af.service.administration.api.monitoring.ProcessContextFactory.ParamSet but i don't know whether this API will support or not and also i don't know how to develop the code using this API so please suggest me some code for it so that i could retrieve the names.
Thanks you all in advance.
Regards,
Avinash.

Hi,
Just ASMA setting will do the needful. Are you planning to rename your target file name. If yes then only you will require UDF.
Update: Since your directory name will be taken from source file name then you have to use mapping for this, else it will not be possible.
I don't know if creating a new module for this will help you solve the issue, but in that case rather creating adapter module, mapping will be easier.
Regards,
Sarvesh
Edited by: Sarvesh Singh on Dec 7, 2009 3:04 PM

ADP and Ceridian Interfaces

Similar Messages

Maybe you are looking for