AFS grid value/valuation type not picked in sales order cost estimate

Hi Experts,
We have different valuation types in the material master. This is part of the AFS, where each grid value is a valuation type. While making a sales order cost estimate and in one sales order item, we have 3 grid values (valuation types), system is costing only for one grid value and that too for the entire quantity. This way the costing is wrong as different grid values have different BOMs and routings.
Is there any specific setting to have the grid value to be picked up in the sales order cost estimate? Or am i missing some setting? in general product costing settings or AFS product costing settings?
Best Regards
Vimal

Hi,
Do you mean "sales order costing", please if so then please ref. the link:
http://help.sap.com/saphelp_46c/helpdata/en/90/ba6da4446711d189420000e829fbbd/content.htm
Regards
DSR
Edited by: D.Srinivasa Rao on Nov 25, 2011 8:19 AM

Similar Messages

Plan value(break up) not appearing in sales order cost report

hi
I have done sales order bom in cs61,operation in ca01,in va02 for sales order costing in itemization showing like
material 100
actity 10
total 110
saved and if I see in cost report it show only revenue , cogs(110),but it is not show raw materials and operations.
please advise me what to do?
Thanks and Regards,
Nagesh

Dear Nagesh,
Probably, you need to check the status of the BOM and the Routing in the Header. It should be active/released.
Kind Regards
Umapathi G
Edited by: Umapathi Naidu G on Aug 11, 2011 3:26 PM

Sales order cost estimate not happening because of GIT B/S account

Hi,
Requirement is to have Goods in Transit account in PGI and reverse it in Invoice no issues iwth it.
For the same sales order user wants to get cost using sales order cost estimate.
When i run that am getting following error
Item 00001 : Cost element 14001212 does not exist in CO area 0010 for 10/07/2011
Message no. KK689
Even though i maintain the CE for Balance sheet account with Cost element category 90 its not accpeting.
Can you please help me on how to proceed for sales order cost estimate.
Thanks,
sudha

hi,
if you give a balance sheet account in obyc , you will not be able to create a cost elementin category 01 , accordignly system will give error in sales order costing , as its not able to get correct cost element in cost planning.
if your requirement is just to post cogs to a balance sheet account which is goods in transit and when invoice is done cogs to be posted.
you should actually use revenue based RA functionality on sales order instead of assinging a balance sheet account in obyc.
in this approach;
- first assign a p/l account in obyc and create cost element in cateogry 01.
- create revenue based RA and assign RA key in requirement class.
- in OKG8 for RA category WIPR and your ra key assign , goods in transit account and give a offsetting account which is not cost element (credit entry in offsetting account nullify debit in account given in OBYC when GIT is posted , when billing is done system will automatically post a oppsite entry in both account).
-in OKG8 for RA category COSR give the COGS account and a offsetting account without cost element (credit entry in offsetting account nullify debit in account given in OBYC when COGS is posted).
regards
rajesh

Condition type not coming in sales order

Hi,
we have a condition type Z026. The issue is that it is not set in the order but the condition records exists. The pricing analysis shows that condition reocrd is missing but the fact is the condition record is there. The acess seq is Z026 and there are many tables in the acess sequence.
The first table in the access seq is 906 and the condition record exists but still the system says that the condition record is not found using cond preliminary step (header fields like customer/sales org/div). the cond record is maintained for relevant sales org/dist channel/customer/material. cond preliminary step means that system first looks for the header fields but everything is there.
The condition is active and the conditon is created on 21.7.10 with validitity from 21.7.10 to 31.1.2010 and the pricing date in sales order is 27.7.10. so everyhting is fine but yet the condition is not coming in sales order
what could be the issue.
regds

Hi,
Now try creating a sales order with 20.07.2010 as the pricing date. It will work. Create another order with 21.07.2010 and it will not work. If so, it is due to the validity date. When you give 21.07.2010 as validity date and there is already another record which was valid on that date, the gap of one day can happen and we have experienced this. There is even an OSS note explaining this concept, which makes sense business-wise.
However you check the scenarios I have mentioned. If the behaviour is as I have mentioned, then you have to change the pricing date of your problamatic sales order to one day earlier, or move the validity date one day earlier.
If the behaviour is different, pls lemme know

Valuation type not available in Production Order

Hi experts,
We are unable to settle production order ,because In CO03,under "Goods Receipt block",no valution type mentioned in "valuation type block".
Please advise.
Regards,
Samar

Hi
Check the material master, whether split valuation is activated or not.
rajeswari

Condition type JEXP not picking in sales order

hi
i was working with all configuration of TAXINN
i am facing with a problem
when i am running mine sales order i am not able to see condition type JEXP(BED) , JEAP (AED)
can i now where i am gng wrong
whereas i can see all the other condition in sales order
but when i enter it manually JEXP it is taking but in again in billing it is not showing
can u plz help me
Regards
Vini

Dear Vini,
Please Check the configuration settings through IMG path
SPRO>IMG>Logistics general-->Tax on Goods movements >India>Basic settings-->Determination of Excise Duty -->Maintain Excise defaults here you check JEXP condition type is maintaining for A/R BED or not if not maintain then try.
Also check the condition record maintanance for the JEXP condition type through VK12 transaction.
I hope this will help you,
Regards,
Murali.
Edited by: Murali Mohan.Tallapaneni on Oct 1, 2008 6:51 AM

Partner VN is not picking in sales order pricing

Hi
My client requirement is system has to calculate commission amount depend on the combination of sold to party and commission agent(created as vendor).
I defined one condition type by adding access sequence in that access sequence i have maintained one table which is having fields of VKORG, KUNNR, LIFNR. and i have maintained condition records with this combination,
And i maintained VN partner in CMR & it is coming into sales document header and item
Even thou system is not picking the condition value, in analysis system is not picking the vendor number (access not made)
can any body suggest me on this issue
regards
bvdv
Edited by: bvdv on Oct 14, 2008 3:13 PM

Vendor will not be automatically populated in the pricing stuctures. You will have to use exit USEREXIT_PRICING_PREPARE_TKOMK in program MV45AFZZ to fill the pricing communication structure.
Regards,
GSL.

Control Code from Material not picked in Sales Order after EHP4

Hi Gurus,
We have updated Enhancement Package 4 for one of our client.
It is observed that the system is not picking the values maintained in Control Code of Material master. We have some pricing condition types maintained using the combination of Control Code and other fields, which are not being determined automatically.
The data is maintained in J1ID for this material and plant combination and it is also filled in material master.
Please help.
Thanks in Advance.
Regards
Vamsi.

Hi Vamsi,
We are also facing the same issue after EHP4 upgrade. Please let me know how you have fixed that issue.
Thanks
Rehan Manzoor

UOM problem and PR00 not picking in sales order

Dear Gurus,
Material UOM -->       CARTON
Additional Data -->     30 PC= 1 CAR
VK11 -->                   1pc = Rs.10
When raising a Sales order, system is not picking up PR00. When checking in VK13, system is showing
1 CAR = Rs. 282.03
How is this happening? If 1pc is Rs.10, 1carton should be Rs.300.
Yesterday i put a question in this forum asking if i can sell in pieces after entering UOM as carton. I was suggested to put 30pc = 1carton in Additional data, which I did and checked to find the system working fine. But today to show this to my boss, system is not picking the PR00 and its value in VK13 as 282.03.
I am totally confused here. Plz help me from this maddening situation.
Thanks and regards.
Venkat

Hi
Go to sales order -> item data -> conditions tab and click on analysis , see what is the message system is giving.
Another clarification is that when system is not picking PR00 ctype then how you are able to tell the value is 282.50.
Check the step in Pricing procedure for PR00 where you have assigned.
Regards
Srinath

Commission Group not picking in sales order

Hi
We have created the Commission Group (ie. 6 ) in product master in R/3 and successfully downloaded in to CRM product master. When we create the sales order in CRM the relevant commission is not being picked up in the order from the product master. When we check at the item level of the order under general tab by default the commission grp is taken as 1 instead of 6 which was maintained in the product master.
All the other date like Vol rebate grp , Product group and product hierarchy has picked up correctly from product master. Only Commission grp is not getting picked as maintained in product master.
Plz help.
Rgds
Praveen Raj

Hi Dave,
As you suggested first execute PP order settle to sales order which I have done. After that I have done RA on Sales Order through KKA3. It has saved the record and value flows correctly. After that while I am going to VA88 for Sales Order settlement it is asking for setlment rule which I doubt. If the Sales order is sender what will be its receiver ? During PP order settle to sales order it was PP order in sender and receiver category was material and reciver was Sales document Numeber. What will be its reciver when Sales order is sender.
Kindly need your valuable suggestion ...
Best Regards,
Samrat Roy
Edited by: Samrat Roy on Feb 10, 2012 2:49 AM

Condition type not determine in sales order

I have condition record maintained for the condition type as per the order reason. When I create the sales order system is not reading the condition record so no condition type is getting determined. Pricing date from the sales order is within the validity period of condition record.Parmeters are also matching but still in the sales order condition type is not getting determine.
Thanx
PNU

In that case, do update of pricing.
To do that, Sales Order - Item data - Condition Tab - Click Update button and choose option B - Carry out new pricing.
To know who manually remove this.
Choose Enviroment from menu bar in sales order - choose Change for display of change in the doc.
Regards
JP

Discount condition type not appearing in sales order but in invoice

Hi,
I have two discount condition types (MPDI,ZSDI) in my pricing procedure,at the time of sales order creation one discount condition is not appearing.
On analyzing the condition type MPDI,system throws message "Access not been executed due to previous access",what would be the reason.
In the billing ,i could see the condition type appearing.I have checked this,but i could not understand why it is happening.Even the condition catergory of condition is empty not L.
Also please find the screen shots below,
Pradeep

Pradeep,
Am sure user might have deleted the condition type in sales order, the same condition type woudl have entered manually in invoice.
Please check my testing, i have done the same entered ZA09 manually and after saving have deleted again in sales order, after dilivery and when i created invoice here i have entered manually the same condition type.
So in your case also the same thing could have happend, check the change log and also in invoce condtion tab check the condtion type in analysis ( Invoice analysis not order). so that you can udnerstand whether it was entered manully or not.
On analyzing the condition type MPDI,system throws message "Access not been executed due to previous access",what would be the reason.
This is because in the condtion tyoe the abvoe key combiantion was found with records hence the below key combition was ignored. this you observe in your screen shot with with 5.00
So my guess is the condtion records was deleted in sales order.
thanks,
srinu.

Profit center is not picking from sales order to the billing document

Hi
I am creating billing document but it is not picking profit centre from the sales order.
Could you please help me in this.
thanks in advamce.

Hi,
Ensure that the profit center is assigned to your Sales order.
Also maintain the following settings in copy control.
Goto the T.Code "VTFA".
Select your valid combination.Details.
Double click on "Item".Select your Item category.
Details.
Maintain "Copy requirements" as "002".
Data VBRK/VBRP as "002".
Regards,
Krishna.

Output type not determined in Sales Order

Hello Friends,
I am facing a problem.
I have maintained the O/P condition record for O/P type for order confirmation.
While creating sales order, in the determination analysis for O/P , it shows as O/P found, but the same is not added in the sales Order outputs.
Can somebody advise me what is missing ?
Regards

Harsh Mathur ,
1. You need to maintain Condition records in VV11 for BA00 (Key combination - order type)
2. If already created Check whether the records are existing through VV12
3. If yes, then enter into your sales order in VA02 Mode
4. Check Extras --> Output --> Header --> Edit
If status is yellow or green then it is ok. Output = BA00, Medium = Print output, Function = SP
Then Choose the line and click "Communication Method" Enter Logical destination - LP01 and activate the indicator against "Print Immediately"
Click Back button --> Click "Further Data"
Under "Requested Processing" header
Dispatch time = Choose the option accordingly
save it.
Then counter check the config by running sales transaction without saving check
Check Extras --> Output --> Header --> Print Preview
if the output is shown then you have succeded
Regards
Sathya

Requirement Type not populated in Sale Order

Hi,
In our sales order a requirment type 041 is not getting populated into the sales order for one particular item category.
Regards,
Jagan

Requirement type determination in standard SAP is performed using a six-level hierarchical
sequence:
1. First, SAP tries to determine the requirement type using the strategy group from
the material master record.
2. If the strategy group is not maintained, SAP determines the requirement type
using the MRP group from the material master record.
3. If this is not maintained either, the SAP system determines the requirement type
using the material type from the material master record.
4. If this also fails, the SAP system determines the requirement type using a combination
of the item category and MRP type.
5. If this rule is not maintained, the SAP system at last tries to determine the
requirement type using the item category itself.
6. If no requirement type is found at this level, the system treats the transaction
as not relevant for the transfer of requirements or availability check.
Regards
Deb

AFS grid value/valuation type not picked in sales order cost estimate

Similar Messages

Maybe you are looking for