AIR-LAP1242G

Hi Everbody,
Cisco 8500 controller's (software 7.4.100.0) datasheet clearly states Cisco AIR-LAP1242G series access point can join cisco 8500 controller. I am using Cisco AIR-LAP1242G software version (C1240-K9W8-M, 12.3(7)JA1, RELEASE SOFTWARE (fc1)) and IOS (c1240-k9w8-mx.ap_jmr3_esc.201204191421/c1240-k9w8-mx.ap_). I tried both console and web interface but Ap did not connect the Cisco 8500 controller.
Is anyone have an idea about this problem
Regards

We are normally using AIR-LAP1242G series Ap with Wism controller. AIR-LAP1242G APs connect to Wism Controller using DHCP option 43 and its also capwap compatible.
"3) Do a capwap events enabled while the ap joins - do you see anything ? If so post" I do not understand this one
We are also using AIR-LAP1131AG-E-K9 with Wism controller. When I send AIR-LAP1131AG-E-K9 series Ap to 8500 controller, it connects and works fine. But when I send to AIR-LAP1242G series AP, it do not connect to 8500 controller.

Similar Messages

AIR-LAP1242G-E-K9 do not work with AIR-CT5508-K9 while AIR-LAP1142N-E-K9 do

Hello,
we do have a site where we need to deploy AIR-LAP1142N-E-K9 and AIR-LAP1242G-E-K9 APs. We have two AIR-CT5508-K9 controllers with SW version                  6.0.188.0.
AIR-LAP1142N-E-K9s work okay, as expected, we do not have any problems with them.
However AIR-LAP1242G-E-K9s do not, there is a problem with establishing CAPWAP tunnel with the controller.The AP is seen on the controller for a while, with 0 time up-time, cannot change any settings on the AP via controller, and after a while it disapears from the controller, apears again and this repeats.
The APs and controllers are connected to the LAN campus.
Controllers via two 1G links configured as Etherchannel to WS-C6506-E VSS switch with s72033-ipservicesk9_wan-vz.122-33.SXI1.bin on it.
APs to WS-C3750G-48PS with c3750-ipbasek9-mz.122-50.SE2.bin on it. 3750 is connected to the C6505 via two 1G links configured as Etherchannel.
Below I copied the log I captured on 1242 and the controller. Highlighted ones are the ones which I think might bring a clue.
I performed some troubleshooting steps.
- As we have some other controllers available over WAN, I tested the 1242 AP with 2100, 4400 and also with the same model AIR-CT5508-K9 with SW version                  6.0.188.0 over WAN and this worked always okay.
- I wanted to be sure that I eliminate any kind of out of sequence packet issue, so I brought down all redundancy L2 links so that the L2 path from the AP to the controller was only through one leg links.
- I also brought the second controller down to eliminate potential issue with having two of them up.
- The AP gets its IP from DHCP configured on the C6506 switch, I am always able to ssh to AP, so the IP connectivity does not seem to be an issue.
- I have more 1242s, all behave in the same way. I also connected them to some other 3750 switches we have in the campus, always the same.
- As this seems to be maybe a kind of ssl issue, I tried to play with controller settings, like enabling Accept... options under Security/AP Policy,but this did not help.
- I also tried to reboot the controller, no improvement.
- The APs came from the factory, so in the beginning everything was factory default in them. They were always able to download the image from the controller in the very initial phase. I still do have some of them untouched, so I can perform any troubleshooting steps with the fresh one.
I can reproduce this, can also send debugging logs if needed.
Any idea on what could be wrong is highly appreciated.
Thank you.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
This Discussion has been converted into document:- https://supportforums.cisco.com/docs/DOC-23054
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
AIR-LAP1242G-E-K9 10.0.13.28 log
*Mar 1 00:00:05.922: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:07.536: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot1 1Radio 0
*Mar 1 00:00:07.672: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 304 messages)
*Mar 1 00:00:09.809: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:09.874: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1240 Software (C1240-K9W8-M), Version 12.4(21a)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 02-Nov-09 18:42 by prod_rel_team
*Mar 1 00:00:09.874: %SNMP-5-COLDSTART: SNMP agent on host wuen4028 is undergoing a cold start
*Mar 1 00:00:09.964: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:00:09.967: bsnInitRcbSlot: slot 1 has NO radio
*Mar 1 00:00:10.191: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:00:10.191: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:00:10.430: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:00:10.818: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 00:00:11.212: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:18.315: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.0.13.28, mask 2 55.255.255.0, hostname wuen4028
*Mar 1 00:00:28.988: Logging LWAPP message to 255.255.255.255.
*Mar 1 00:00:31.456: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:00:31.495: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:00:32.457: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:00:32.457: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated
*Mar 1 00:00:38.810: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:00:47.811: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 1 00:00:56.812: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER
*Mar 1 00:01:07.815: %CAPWAP-3-ERRORLOG: Selected MWAR 'wuen4001'(index 0).
*Mar 1 00:01:07.815: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Feb 11 07:52:24.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.0.13.5 peer_port: 5246
*Feb 11 07:52:24.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Feb 11 07:52:25.441: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.0.13.5 peer_port: 5246
*Feb 11 07:52:25.443: %CAPWAP-5-SENDJOIN: sending Join Request to 10.0.13.5
*Feb 11 07:52:25.443: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Feb 11 07:52:25.445: %CAPWAP-3-ERRORLOG: Unencrypted non-discovery CAPWAP Control Message from 10.0.13.5
*Feb 11 07:52:25.445: %CAPWAP-3-ERRORLOG: Invalid AC Message Type 4.
*Feb 11 07:52:25.445: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Feb 11 07:52:25.445: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 10.0.13.5
*Feb 11 07:52:30.441: %CAPWAP-5-SENDJOIN: sending Join Request to 10.0.13.5
*Feb 11 07:52:30.442: %CAPWAP-3-ERRORLOG: Unencrypted non-discovery CAPWAP Control Message from 10.0.13.5
*Feb 11 07:52:30.443: %CAPWAP-3-ERRORLOG: Invalid AC Message Type 4.
*Feb 11 07:52:30.443: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Feb 11 07:52:30.443: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 10.0.13.5
*Feb 11 07:52:47.644: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Feb 11 07:53:23.999: %DTLS-5-SEND_ALERT: Send WARNING : Close notify Alert to 10.0.13.5:5246
*Feb 11 07:53:24.000: %CAPWAP-3-ERRORLOG: Selected MWAR 'wuen4001'(index 0).
*Feb 11 07:53:24.000: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Feb 11 07:52:24.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.0.13.5 peer_port: 5246
*Feb 11 07:52:24.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Feb 11 07:52:24.001: %DTLS-5-PEER_DISCONNECT: Peer 10.0.13.5 has closed connection.
*Feb 11 07:52:24.001: %DTLS-5-SEND_ALERT: Send WARNING : Close notify Alert to 10.0.13.5:5246
*Feb 11 07:52:24.002: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 3 combination.
*Feb 11 07:52:24.123: %CAPWAP-3-ERRORLOG: Dropping dtls packet since session is not established.
wuen4028#
AIR-CT5508-K9 10.0.13.5 log
*Feb 11 09:00:54.824: %DTLS-3-HANDSHAKE_FAILURE: openssl_dtls.c:2171 Failed to c
omplete DTLS handshake with peer 10.0.13.28
                                           *Feb 11 08:59:53.798: %DOT1X-3-MAX_EA
P_RETRIES: 1x_auth_pae.c:2862 Max EAP identity request retries (3) exceeded for
client 00:1f:3b:93:dd:4f
*Feb 11 08:59:51.197: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2862 Max EAP ident
ity request retries (3) exceeded for client 00:c0:a8:e1:b1:71
--More-- or (q)uit
*Feb 11 08:59:21.212: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:292 RRM LOG: Airewave Di
rector: Could not find valid channel lists for 802.11bg
*Feb 11 08:58:39.766: %DTLS-3-HANDSHAKE_FAILURE: openssl_dtls.c:2171 Failed to c
omplete DTLS handshake with peer 10.0.13.28
                                           *Feb 11 08:57:06.131: %RRM-3-RRM_LOGM
SG: rrmChanUtils.c:292 RRM LOG: Airewave Director: Could not find valid channel
lists for 802.11bg
*Feb 11 08:56:24.504: %DTLS-3-HANDSHAKE_FAILURE: openssl_dtls.c:2171 Failed to c
omplete DTLS handshake with peer 10.0.13.28
                                           *Feb 11 08:55:09.693: %DOT1X-3-MAX_EA
P_RETRIES: 1x_auth_pae.c:2862 Max EAP identity request retries (3) exceeded for
client 00:1f:3b:93:dd:4f
*Feb 11 08:54:51.040: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:292 RRM LOG: Airewave Di
rector: Could not find valid channel lists for 802.11bg
*Feb 11 08:53:56.493: %DOT1X-3-MAX_EAP_RETRANS: 1x_ptsm.c:426 Max EAP retransmis
sions exceeded for client 00:1f:3b:93:dd:4f
*Feb 11 08:53:34.497: %DTL-3-OSARP_DEL_FAILED: dtl_arp.c:1380 Unable to delete a
n ARP entry for 10.0.13.28 from the operating system. ioctl operation failed
*Feb 11 08:52:35.936: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:292 RRM LOG: Airewave Di
rector: Could not find valid channel lists for 802.11bg
*Feb 11 08:52:26.492: %DOT1X-3-MAX_EAP_RETRANS: 1x_ptsm.c:426 Max EAP retransmis
sions exceeded for client 00:1f:3b:93:dd:4f
*Feb 11 08:50:07.680: %DOT1X-3-MAX_EAP_RETRANS: 1x_ptsm.c:426 Max EAP retransmis
sions exceeded for client 00:1f:3b:93:e6:57
*Feb 11 08:48:37.458: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2862 Max EAP ident
ity request retries (3) exceeded for client 00:1f:3b:93:e6:57
*Feb 11 08:47:37.438: %DOT1X-3-MAX_EAP_RETRANS: 1x_ptsm.c:426 Max EAP retransmis
sions exceeded for client 00:1f:3b:93:e6:57
*Feb 11 08:47:34.438: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2862 Max EAP ident
ity request retries (3) exceeded for client 00:16:44:1d:0f:53
*Feb 11 08:46:32.422: %DOT1X-3-MAX_EAPOL_KEY_RETRANS: 1x_ptsm.c:407 Max EAPOL-ke
y M3 retransmissions exceeded for client 00:16:44:1d:0f:53
*Feb 11 08:46:06.790: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2862 Max EAP ident
ity request retries (3) exceeded for client 00:1f:3b:95:61:bd
*Feb 11 08:46:06.789: %DOT1X-3-ABORT_AUTH: 1x_bauth_sm.c:447 Authentication abor
ted for client 00:1f:3b:95:61:bd
*Feb 11 08:46:06.210: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2862 Max EAP ident
ity request retries (3) exceeded for client 00:1f:3b:93:e6:57
*Feb 11 08:45:34.304: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2862 Max EAP ident
ity request retries (3) exceeded for client 00:1f:3b:95:61:bd
*Feb 11 08:45:34.303: %DOT1X-3-ABORT_AUTH: 1x_bauth_sm.c:447 Authentication abor
ted for client 00:1f:3b:95:61:bd
*Feb 11 08:45:01.298: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:292 RRM LOG: Airewave Di
rector: Could not find valid channel lists for 802.11bg
*Feb 11 08:44:38.076: %SIM-3-PORT_UP: sim.c:9547 Physical port 2 is up!.
*Feb 11 08:44:38.037: %SIM-3-PORT_UP: sim.c:9547 Physical port 1 is up!.
--More-- or (q)uit
*Feb 11 08:44:38.009: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
figuration file 'cliWebInitParms.cfg'
*Feb 11 08:44:37.980: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
figuration file 'rrcEngineInitParms.cfg'
*Feb 11 08:44:37.980: %CNFGR-3-INV_COMP_ID: cnfgr.c:2105 Invalid Component Id :
Unrecognized (81) in cfgConfiguratorInit.
*Feb 11 08:44:37.928: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
figuration file 'rfidInitParms.cfg'
*Feb 11 08:44:37.915: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
figuration file 'dhcpParms.cfg'
*Feb 11 08:44:37.903: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
figuration file 'bcastInitParms.cfg'
*Feb 11 08:44:37.834: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
figuration file 'rrmInitParms.cfg'
*Feb 11 08:44:27.331: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
figuration file 'apfInitParms.cfg'
*Feb 11 08:44:27.226: %MM-3-MEMBER_ADD_FAILED: mm_dir.c:903 Could not add Mobili
ty Member. Reason: IP already assigned, Member-Count:1,MAC: 00:00:00:00:00:00, I
P: 0.0.0.0
*Feb 11 08:44:27.023: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
figuration file 'mmInitParms.cfg'
*Feb 11 08:44:27.013: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
figuration file 'aaaapiInitParms.cfg'
*Feb 11 08:44:27.011: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
figuration file 'pemInitParms.cfg'
*Feb 11 08:44:26.898: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
figuration file 'dot1xInitParms.cfg'
*Feb 11 08:44:26.868: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
figuration file 'capwapInitParms.cfg'
*Feb 11 08:44:26.718: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
figuration file 'spamInitParms.cfg'
*Feb 11 08:44:25.650: %SSHPM-3-FREAD_FAILED: sshpmlscscep.c:1395 Error reading f
ile /mnt/application/lscca_pem.crt
*Feb 11 08:44:06.435: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
figuration file 'sshpmInitParms.cfg'

Thanks for such quick response and suggestions.
Yes, I seem not to to be 100% perfect as for the list of troubleshooting steps I took.
I had already tried the two commands you mentioned. I tried again, this time with some other 1242, but these do not help.
Yes, I was already thinking that this could be in theory a licensing issue. The controller is bougth with 25 licenses.
In the beginnign I had one 1142 on it and tried to enable 1242s which did not work. Now I have five 1142s on it, as this worked okay, I guess it could not be a licensing issue.
I think that I can see in the log files that the machines communicate to each other, L2 or L3 paths seem to be working okay. I forgot to mention that I am using option 43 on the DHCP server, so the AP clearly finds its way to the controller. What's more both APs and the controllers are in the same VLAN, so they are in the same broadcast domain.
Below is sho ver from the AP. The AP seems to have Certificate type - manufacture installed, so I guess there should not be a problem with the certificate, especially knowing that the AP works with other controllers over WAN.
My guess these messages seen on AP especially "Invalid event 38 & state 3 combination" might tell us what's wrong.
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman";
mso-ansi-language:#0400;
mso-fareast-language:#0400;
mso-bidi-language:#0400;}
*Feb 11 07:52:24.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Feb 11 07:52:24.001: %DTLS-5-PEER_DISCONNECT: Peer 10.0.13.5 has closed connection.
*Feb 11 07:52:24.001: %DTLS-5-SEND_ALERT: Send WARNING : Close notify Alert to 10.0.13.5:5246
*Feb 11 07:52:24.002: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 3 combination.
*Feb 11 07:52:24.123: %CAPWAP-3-ERRORLOG: Dropping dtls packet since session is not established.
Cisco IOS Software, C1240 Software (C1240-K9W8-M), Version 12.4(21a)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 02-Nov-09 18:42 by prod_rel_team
ROM: Bootstrap program is C1240 boot loader
BOOTLDR: C1240 Boot Loader (C1240-BOOT-M) Version 12.4(13d)JA, RELEASE SOFTWARE (fc2)
AP9caf.ca00.1c78 uptime is 17 minutes
System returned to ROM by power-on
System image file is "flash:/c1240-k9w8-mx.124-21a.JA2/c1240-k9w8-mx.124-21a.JA2"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-LAP1242G-E-K9    (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
Processor board ID FCZ135082GH
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
LWAPP image version 6.0.188.0
1 FastEthernet interface
1 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 9C:AF:CA:00:1C:78
Part Number                          : 73-11479-01
PCA Assembly Number                  : 800-30493-01
PCA Revision Number                  : A0
PCB Serial Number                    : FOC13484GYY
Top Assembly Part Number             : 800-29589-03
Top Assembly Serial Number           : FCZ135082GH
Top Revision Number                  : A0
Product/Model Number                 : AIR-LAP1242G-E-K9
Configuration register is 0xF
AP9caf.ca00.1c78#

AIR-LAP1131G and AIR-LAP1242G Latest WLAN Controller Compatibility

Would like to ask if below APs are compatible with WLC 5508 with current version of 7.0.240.0:
Cisco AIR-LAP1131G-A-K9
Cisco AIR-LAP1242G-A-K9

Yes they are supported in that version.
You want to check the release notes for AP support.
http://www.cisco.com/c/en/us/td/docs/wireless/controller/release/notes/crn7_0_240_0.html#wp784295
HTH,
Steve

Need urgent help in AIR-LAP-1242G-E-K9

Hi all,
Im new into the Cisco Wireless. I have a Cisco's AIR-LAP1242G-E-K9...I dont have WLC, i want to use it as standalone AP for wireless Access to my users ... i took the console of AP & got the following msgs!!!!
AP68ef.bde3.3ad4#
AP68ef.bde3.3ad4#
AP68ef.bde3.3ad4#
AP68ef.bde3.3ad4#
AP68ef.bde3.3ad4#
*Mar 1 00:18:55.021: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
Not in Bound state.
*Mar 1 00:19:05.651: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 172.10.10.16, mask 255.255.255.0, hostname AP68ef.bde3.3ad4
*Mar 1 00:19:10.524: %CAPWAP-3-ERRORLOG: Invalid event 29 & state 4 combination.
*Mar 1 00:19:10.524: %CAPWAP-3-ERRORLOG: SM handler: Failed to process timer message.
*Mar 1 00:19:10.524: %CAPWAP-3-ERRORLOG: Failed to handle timer message.
*Mar 1 00:19:10.525: %CAPWAP-3-ERRORLOG: Failed to process timer message.
*Mar 1 00:19:10.525: %CAPWAP-3-ERRORLOG: Discovery interval timer expiry handler failed.
*Mar 1 00:19:10.587: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:19:10.587: bsnInitRcbSlot: slot 1 has NO radio
*Mar 1 00:19:10.595: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 1 00:19:10.608: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:19:10.609: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:19:12.606: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
Translating "CISCO-LWAPP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:19:21.607: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 1 00:19:30.608: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER
*Mar 1 00:20:20.614: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
Not in Bound state.
*Mar 1 00:20:31.244: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 172.10.10.17, mask 255.255.255.0, hostname AP68ef.bde3.3ad4
*Mar 1 00:20:36.117: %CAPWAP-3-ERRORLOG: Invalid event 29 & state 4 combination.
*Mar 1 00:20:36.117: %CAPWAP-3-ERRORLOG: SM handler: Failed to process timer message.
*Mar 1 00:20:36.118: %CAPWAP-3-ERRORLOG: Failed to handle timer message.
*Mar 1 00:20:36.118: %CAPWAP-3-ERRORLOG: Failed to process timer message.
*Mar 1 00:20:36.118: %CAPWAP-3-ERRORLOG: Discovery interval timer expiry handler failed.
*Mar 1 00:20:36.183: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:20:36.183: bsnInitRcbSlot: slot 1 has NO radio
*Mar 1 00:20:36.190: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 1 00:20:36.203: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:20:36.204: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:20:38.202: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
AP68ef.bde3.3ad4#
AP68ef.bde3.3ad4#
Because of frequent change in IP's i cant take the console of AP ..
Can any body tell me what is the problem & its solution .. & if any body share the basic configuration guide it will be appreciated
Thanks in advance &
Plz reply ASAP ....

Thanks leo,
Appreciated your help & immediate support ... i will upgrade the IOS & will let you know if any problem.
One more Question :
I have an 1140 AP, which is connected Standalone in the network. Its Up & Running in the environment. Some time users got disconnect from AP & are not able to get the IP from DHCP, when i took the web interface of AP i got following error in Event Log
Interface Dot11Radio0, Deauthenticating Station 0011.21ce.bfe4 Reason: Previous authentication no longer valid
Please have alook on attached snap shot for all the event logs.
Please suggest what could be the problem.
Regards

Apply button not working when changing AP settings

Hi Guys,
I am working on installing a new 2500 Controller with 2 AIR-LAP1242G's attached to it. I have both registered and on the controller but I am having trouble moving one of them to a new IPS AP group that I created. Furthermore, I noticed the default gateway is missing from the static ip settings and I am unable to add that as well. When I add the default gateway and hit apply, the controller does nothing. Same thing for when I try to change my WIPS device to monitor mode. Has anyone ever seen behaivor like this?
A couple other things that I noticed is that when I go to AP groups and try to remove the AP's from the default group, there is no remove button when you go inside the default group like I see when i go into my IPS group.
The AP's are on software ver 12.4(23c)JA3 Boot ver 12.4.13.0
and the controller is at 7.0.22.0
I have already power cycled the controller and both AP's. Is there anything else that anyone can think to look at here?

Grrr.....I tried everything but closing the browser out and opening a new session. I logged out and back in without closing internet explorer completely but it turned out closing internet explorer solved this.

Duplicated IP error on some clients

Hello, Dear All.
We have typical deployment with WLC550x (7.0.116.0) and 16 APs (AIR-LAP1242G-E-K9) placed on same site. WLC connected to 3560 (with LAG , and dhcp relay) , and all wireless clients( Motorolla MC3100 handled PC ) work with same WPA2-PSK SSID. All APs configured as HREAP group and SSID has local switching and auth settings. DHCP server for clients work on Windows 2008r2 failover cluster, APs give addresses from WLC builtin server.
Almost all works great. But sometimes some clients go insane . After wake up, they show duplicate IP error and wont connect to nework. On DHCP server this IP shown as leased to client mac(without any errors and so).
Client reboot wont resolve this issue.
After reboot client try another dhcp address (after marking dchp decline message) but also without luck, with same error and another IP.
All this looks like client side problem . But when i try debug arp on root switch 3560 i get following situation.
After client wake-up
*Apr 10 18:44:32.773: IP ARP: rcvd req src 10.116.51.59 0023.68cb.a8fc, dst 10.116.51.59 Vlan51
*Apr 10 18:44:32.782: IP ARP: rcvd req src 10.116.51.59 0023.68cb.a812, dst 10.116.51.59 Vlan51
After reboot
*Apr 10 19:16:40.123: IP ARP: rcvd req src 10.116.51.24 0023.68cb.a8fc, dst 10.116.51.24 Vlan51
*Apr 10 19:16:40.131: IP ARP: rcvd req src 10.116.51.24 0023.68c9.a29b, dst 10.116.51.24 Vlan51
*Apr 10 19:16:40.459: IP ARP: rcvd req src 10.116.51.27 0023.68cb.a8fc, dst 10.116.51.27 Vlan51
*Apr 10 19:16:40.467: IP ARP: rcvd req src 10.116.51.27 0023.68cb.a9b6, dst 10.116.51.27 Vlan51
Where 0023.68cb.a8fc problem clent mac and   0023.68cb.a812,
0023.68cb.a9b6, 0023.68c9.a29b    - another full working clients MACs(with another ip address).
Looks like another client (or ?? ap or controller) send ARP reqest with same IP right after problem client. How this possible ?
I'll be
appreciate for any opinions
and comments!

Why you think so ?
Reboot of controller resolve problem for some time.
Clients work flawlessly when controller disconnected from network and APs in H-REAP mode. Also same clients (handles PC models) works in online mode with wlc 4400 without problems.
There are two difference in this deployment:
1. wlc 5500 and 7.0 major release
2. APs in H-REAP mode and WLAN configured as localy switched
From my point of view problem related with controller incorrect behavior(or I think so).
Process of obtaining ip addresses interrupted by controller   for some unclear reasons.
1.Client obtain IP address from DHCP without problem(via dhcp relay on 3750)
2. Client check that no one use it by sending ARP request "ARP Who has address (leased from DHCP address here)"
3. No response mean that address free.
4. Controller interrupt process. By sending ARP resposne "ARP (leased from DHCP address here) used by (MAC of one of client what used it in past)   "
5. After this client show duplicated ip error.
6. Controller log message
%APF-4-REGISTER_IPADD_ON_MSCB_FAILED:apf_foreignap.c:1504 Could not Register IP Add on MSCB. Identity theft alert for IP address. Address:00:23:68:cb:a9:87
I think this mean controller failed to update some internal table with new ip-mac pair and prevent client work.
But how disable such controller behavior I dont know.
I disabled controller DHCP proxy , I disabled client ip learning in WLAN settings , I disabled any exclusion policies.

Cisco Wireless AP

Hi
I have a cisco wireless AP AIR-LAP1242G-E-K9
When I plug the network cable into the back this lights come on and change colour.
Does anyone know what the lights mean when they change colour?
Thanks
Regards

Hi Jayesh,
Color change can be due to many reasons
Status LED indicates operating state, association status, error/warning condition, boot sequence, and maintenance status.
Ethernet LED indicates status of activity over the Ethernet.
Radio LED indicates status of activity over the radio.
http://www.cisco.com/en/US/docs/wireless/access_point/1240/installation/guide/124h_c4.html
Regards
NikhiL

Migrating from Cisco 4402 to 5508 - AP Compatibility

We currently run six 4402 Wireless lan controllers - these are managed by a WCS server - soon to be replaced by Cisco Prime.
We run a mixture of LAP1242 and LAP1142 wireless access points.
I need to add more but have been told by my supplier that the both these AP's are now end of sale and cannot be purchased.
The replacement AP's are the 2600 series - but I have been told that these are not compatible with my existing 4402 controllers.
To make matters worse I was then advised that if I purchase the new 5580 controllers the older LAP1242 access points will not work with it and require replacing - this, for me, is a lot of access points.
What I need to know is:
What access points, if any, are currently available that are compatible with my 4402 controllers and a future 5508 installation?
I ssem to be in a situation now where I cannot buy any access points that will work with my 4402's but if I upgrade all my current 1242's will not funtion with the new 5508 controller!
Scott

Please look at the compatibility matrix of WLC release and AP's support (it is base on Controller software release)
Software Support for Access Points
Access Points
First Support
Last Support
1000 Series
AIR-AP1010
3.0.100.0
4.2.209.0
AIR-AP1020
3.0.100.0
4.2.209.0
AIR-AP1030
3.0.100.0
4.2.209.0
Airespace AS1200
4.0
AIR-LAP1041N
7.0.98.0
AIR-LAP1042N
7.0.98.0
1100 Series
AIR-LAP1121
4.0.155.0
7.0.x
1130 Series
AIR-LAP1131
3.1.59.24
1140 Series
AIR-LAP1141N
5.2.157.0
AIR-LAP1142N
5.2.157.0
1220 Series
AIR-AP1220A
3.1.59.24
7.0.x
AIR-AP1220B
3.1.59.24
7.0.x
1230 Series
AIR-AP1230A
3.1.59.24
7.0.x
AIR-AP1230B
3.1.59.24
7.0.x
AIR-LAP1231G
3.1.59.24
7.0.x
AIR-LAP1232AG
3.1.59.24
7.0.x
1240 Series
AIR-LAP1242G
3.1.59.24
AIR-LAP1242AG
3.1.59.24
1250 Series
AIR-LAP1250
4.2.61.0
AIR-LAP1252G
4.2.61.0
AIR-LAP1252AG
4.2.61.0
1260 Series
AIR-LAP1261N
7.0.116.0
AIR-LAP1262N
7.0.98.0
1300 Series
AIR-BR1310G
4.0.155.0
7.0.x
1400 Series
Standalone Only
1600 Series
AIR-CAP1602I-x-K9
7.4.100.0
AIR-CAP1602I-xK910
7.4.100.0
AIR-SAP1602I-x-K9
7.4.100.0
AIR-SAP1602I-xK9-5
7.4.100.0
AIR-CAP1602E-x-K9
7.4.100.0
AIR-SAP1602E-xK9-5
7.4.100.0
AP801
ap801-k9w7-tar
5.1.151.0
2600 Series
AIR-CAP2602I-x-K9
7.2.110.0
AIR-CAP2602I-xK910
7.2.110.0
AIR-SAP2602I-x-K9
7.2.110.0
AIR-SAP2602I-x-K95
7.2.110.0
AIR-CAP2602E-x-K9
7.2.110.0
AIR-CAP2602E-xK910
7.2.110.0
AIR-SAP2602E-x-K9
7.2.110.0
AIR-SAP2602E-x-K95
7.2.110.0
3500 Series
AIR-CAP3501E
7.0.98.0
AIR-CAP3501I
7.0.98.0
AIR-CAP3502E
7.0.98.0
AIR-CAP3502I
7.0.98.0
AIR-CAP3502P
7.0.116.0
3600 Series
AIR-CAP3602I-x-K9
7.1.91.0
AIR-CAP3602I-xK910
7.1.91.0
AIR-CAP3602E-x-K9
7.1.91.0
AIR-CAP3602E-xK910
7.1.91.0
600 Series
AIR-OEAP602I
7.0.116.0
Note The Cisco 3600 Access Point was introduced in 7.1.91.0. If your network deployment uses Cisco 3600 Access Points with release 7.1.91.0, we highly recommend that you upgrade to 7.2.103.0 or a later release.
1500 Mesh Series
AIR-LAP-1505
3.1.59.24
4.2.207.54M
AIR-LAP-1510
3.1.59.24
4.2.207.54M
1520 Mesh Series
AIR-LAP1522AG
-A and N: 4.1.190.1 or 5.2 or later1
All other reg. domains: 4.1.191.24M or 5.2 or later1
AIR-LAP1522HZ
-A and N: 4.1.190.1 or 5.2 or later1
All other reg. domains: 4.1.191.24M or 5.2 or later1
AIR-LAP1522PC
-A and N: 4.1.190.1 or 5.2 or later1
All other reg. domains: 4.1.191.24M or 5.2 or later1
AIR-LAP1522CM
7.0.116.0 or later.
AIR-LAP1524SB
-A, C and N: 6.0 or later
All other reg. domains: 7.0.116.0 or later.
AIR-LAP1524PS
-A: 4.1.192.22M or 5.2 or later1
1550
AIR-CAP1552I-x-K9
7.0.116.0
AIR-CAP1552E-x-K9
7.0.116.0
AIR-CAP1552C-x-K9
7.0.116.0
AIR-CAP1552H-x-K9
7.0.116.0
AIR-CAP1552CU-x-K9
7.3.101.0
AIR-CAP1552EU-x-K9
7.3.101.0
1552S
AIR-CAP1552SA-x-K9
7.0.220.0
AIR-CAP1552SD-x-K9
7.0.220.0

WLC 5508 - AP 3602i & 1231's

Hi all,
I just got my "new toys" 2 x 5508 with 200 odd 3600 AP's.
I have setup all my SSID's and they work perfectly on code
AIR-CT5500-K9-7-2-110-0
AIR-CT5500-K9-7-2-111-3
AIR-CT5500-K9-7-3-101-0
Now when I tried adding a 1231 AP I keep getting the folloing message.
*Nov 7 13:16:27.104: status of voice_diag_test from WLC is false
*Nov 7 13:16:27.105: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Nov 7 13:16:27.107: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Nov 7 13:16:27.113: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Nov 7 13:16:27.125: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Nov 7 13:16:27.131: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Nov 7 13:16:27.135: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Nov 7 13:16:27.147: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Nov 7 13:16:39.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 57.24.10.53 peer_port: 5246
*Nov 7 13:16:39.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Nov 7 13:16:40.912: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 57.24.10.53 peer_port: 5246
*Nov 7 13:16:40.913: %CAPWAP-5-SENDJOIN: sending Join Request to 57.24.10.53
*Nov 7 13:16:40.914: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Nov 7 13:16:40.916: %DTLS-5-ALERT: Received WARNING : Close notify alert from 57.24.10.53
*Nov 7 13:16:40.916: %DTLS-5-PEER_DISCONNECT: Peer 57.24.10.53 has closed connection.
*Nov 7 13:16:40.917: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 57.24.10.53:5246
*Nov 7 13:16:39.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 57.24.10.53 peer_port: 5246
*Nov 7 13:16:39.002: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Nov 7 13:16:40.917: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 57.24.10.53 peer_port: 5246
*Nov 7 13:16:40.919: %CAPWAP-5-SENDJOIN: sending Join Request to 57.24.10.53
*Nov 7 13:16:40.919: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Nov 7 13:16:40.921: %DTLS-5-ALERT: Received WARNING : Close notify alert from 57.24.10.53
*Nov 7 13:16:40.921: %DTLS-5-PEER_DISCONNECT: Peer 57.24.10.53 has closed connection.
*Nov 7 13:16:40.921: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 57.24.10.53:5246
*Nov 7 13:16:40.989: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Nov 7 13:16:40.990: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Nov 7 13:16:40.991: bsnInitRcbSlot: slot 1 has NO radio
*Nov 7 13:16:41.069: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Nov 7 13:16:41.093: %PARSER-4-BADCFG: Unexpected end of configuration file.
However, on code
AIR-CT5500-K9-7-0-220-0 and AIR-CT5500-K9-7-0-235-3 the 1231 comes and perfectly and works as well as the 3600's with all the SSID's
But my 3600's comes back with a error
Translating "CISCO-CAPWAP-CONTROLLER.flysaa.com"...domain server (57.24.108.21)
*Nov 7 12:06:42.327: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.flysaa.com
*Nov 7 12:06:42.327: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'ACCWirelessCon01'running version 7.0.220.0 is rejected.
*Nov 7 12:06:42.327: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Nov 7 12:06:42.327: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Nov 7 12:06:42.327: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Nov 7 12:06:42.327: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 57.24.10.53
*Nov 7 12:06:42.327: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'ACCWirelessCon01'running version 7.0.220.0 is rejected.
*Nov 7 12:06:42.327: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Nov 7 12:06:42.327: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
Translating "CISCO-CAPWAP-CONTROLLER.flysaa.com"...domain server (57.24.108.21)
Any idea how I can get both of them working on the controller?

Sorry, but I have bad news. The 1231 isnt supported past 7.0 code regardless of the radio ..
Software Release Support for Access Points
Table 1-4 lists the controller software releases that support specific Cisco access points. The First Support column lists the earliest controller software release that supports the access point. For access points that are not supported in ongoing releases, the Last Support column lists the last release that supports the access point.
Table 1-4 Software Support for Access Points
Access Points
First Support
Last Support
1000 Series
AIR-AP1010
3.0.100.0
4.2.207.0
AIR-AP1020
3.0.100.0
4.2.207.0
AIR-AP1030
3.0.100.0
4.2.207.0
Airespace AS1200
4.0
AIR-LAP1041N
7.0.98.0
AIR-LAP1042N
7.0.98.0
1100 Series
AIR-LAP1121
4.0.155.0
7.0.x
1130 Series
AIR-LAP1131
3.1.59.24
1140 Series
AIR-LAP1141N
5.2.157.0
AIR-LAP1142N
5.2.157.0
1220 Series
AIR-AP1220A
3.1.59.24
7.0.x
AIR-AP1220B
3.1.59.24
7.0.x
1230 Series
AIR-AP1230A
3.1.59.24
7.0.x
AIR-AP1230B
3.1.59.24
7.0.x
AIR-LAP1231G
3.1.59.24
7.0.x
AIR-LAP1232AG
3.1.59.24
7.0.x
1240 Series
AIR-LAP1242G
3.1.59.24
AIR-LAP1242AG
3.1.59.24
1250 Series
AIR-LAP1250
4.2.61.0
AIR-LAP1252G
4.2.61.0
AIR-LAP1252AG
4.2.61.0
1260 Series
AIR-LAP1261N
7.0.116.0
AIR-LAP1262N
7.0.98.0
1300 Series
AIR-BR1310G
4.0.155.0
7.0.x
1400 Series
Standalone Only
N/A
3500 Series
AIR-CAP3501E
7.0.98.0
AIR-CAP3501I
7.0.98.0
AIR-CAP3502E
7.0.98.0
AIR-CAP3502I
7.0.98.0
AIR-CAP3502P
7.0.116.0
3600 Series
AIR-CAP3602I-x-K9
7.1.91.0
AIR-CAP3602I-xK910
7.1.91.0
AIR-CAP3602E-x-K9
7.1.91.0
AIR-CAP3602E-xK910
7.1.91.0
Note The Cisco 3600 Access Point was introduced in 7.1.91.0. If your network deployment uses Cisco 3600 Access Points with release 7.1.91.0, we highly recommend that you upgrade to 7.2.103.0.
"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
‎"I'm in a serious relationship with my Wi-Fi. You could say we have a connection."

802.1x Authentication on IPAD and Mac book

We have a few Mac book Air and IPADs (1&2) on our wireless network. They frequently loose connection to the network and the following errors have been come up:
DOT1X-3-MAX_EAP_RETRIES:
DOT1X-3-MAX_EAP_RETRANS
DOT1X-3-INVALID_WPA_KEY_MSG_STATE
DOT1X-3-INVALID_REPLAY_CTR
Please let me know if anyone has encountered this problem and possible remedies which can be applied

Seen this thread?
AIR-LAP1242G-E-K9 do not work with AIR-CT5508-K9 while AIR ...

Cisco Aironet 1200 LAP Issues - LAP to Autonomous Mode

Greetings! After purchasing 4 of the Cisco Aironet 1200 G Series WAPs, I'm now running into a slight issue with them.
I received these last week with the understanding that if I didn't have the Cisco controller device, I could convert them from being the Lightweight Access Point, back to Autonomous mode with an IOS.
With this, I checked the documentation that came with the device and found the "Upgrading Autonomous Cisco Aironet Access Points to Lightweight Mode" or http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=Getting%20Started%20with%20Wireless&needs_authentication=yes&CommCmd=MB%3Fcmd%3Dadd_discussion%26mode%3Dshow%26needs_authentication%3Dyes%26location%3D.ee7c7c3.
From there, I followed the instructions listed under Converting a Lightweight Access Point Back to Autonomous Mode. Before the rename of the file, I checked the device and found AIR-LAP1242G-A-K9 for the Model No.
One of the Cisco Certified admins here was able to obtain the latest build for the IOS for the device or c1240-k9w7-tar.123-8.JEB1.tar. Per the instructions, I renamed the file to coincide with the model of the device.
I followed the instructions from there, and it looked as if everything was going well. However, after the upgrade, I'm running into an issue with the following:
File "flash:/c1200-k9w7-mx.123-8.JEB1/c1200-k9w7-mx.123-8.JEB1" uncompressed and installed, entry point: 0x3000
executing...
At this point, the device just locks up. All lights are lit green on the device. According do the documentation, it should reboot and from there, I should be able to access the web interface by IP.
I've tried to perform the upgrade again using the same IOS build, but the same thing happens with the lock up.
At this point, I'm assuming the issue is with the build of the IOS that I have and I may have to look at getting an older build. However, before doing so, I thought I would post something here to see if anyone had an idea.
I may have needed to refine my searching of the forums, but wasn't able to find anything in relation to my issue. If there is something out there, I do apologize for the post and will happily refer to any current information.
If you need any further information in relation to this, please let me know. Any assistance is greatly appreciated. Thank you!

Hi Jeffrey,
Reverting the Access Point Back to Autonomous Mode
Have a look at Step 3
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
You can convert an access point from lightweight mode back to autonomous mode by loading a Cisco IOS Release that supports autonomous mode (Cisco IOS release 12.3(7)JA or earlier). If the access point is associated to a controller, you can use the controller to load the Cisco IOS release. If the access point is not associated to a controller, you can load the Cisco IOS release using TFTP.
Using a TFTP Server to Return to a Previous Release
Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, and c1240-k9w7-tar.default for a 1240 series access point.
Step 4 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 5 Disconnect power from the access point.
Step 6 Press and hold MODE while you reconnect power to the access point.
Step 7 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 8 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 9 After the access point reboots, reconfigure it using the GUI or the CLI.
From this doc;
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
Hope this helps!
Rob

WLAN Detail Measurement and logging

Hello,
at an event with +150 WLAN clients should I create a report for WLAN usage over the event time..Network environment:
- WLC 5508 (7.2), AIR LAP1242G, access switches: 2960SCriteria for the report:
- How many wireless clients were generally in time connected / associated?
- How long each client was connected or active?
- What has caused traffic each client and all?
- When was which client on which AP is associated?
- How many clients were on the individual APs in each account?Dignity for Netflow (Prime as Collector) sufficient or do I need more?With which board means and how I can for example also in the controller LOG to see when which client was associated with which AP (to find no setting)?What tools can I help it still inserting. Ideas?
I already thank you for your feedback and professional helpBest regards
Alexander

Hello,
sorry, bau at the moment i've found this dokument about Client Reporting with Prime:
http://www.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/2.0/user/guide/reps.html#wp1059688
If someone still one more thing?
Many Thanks
Alexander

WLC upgrade from 5.1.151 to 7.0.116

Dears ,
I have upgraded my WLC from version 5.1.151 to version 6.0.202 and then to 7.0.116 .
Since when , I see that all clients are disconnected every around 20 minutes and re-connected again .
Does anyone has any clues ?
WLC is 4402
AP are AIR-LAP1231G-E-K9 and AIR-LAP1242G-E-K9

when the issue happens.. what does the logs say?? in the mean time.. disable the session timout on all the WLAN on the WLC..
WLC GUI >> WLAN >> WLAN EDIT >> Advanced >> Session timeout >> Uncheck
Regards
Surendra

Access points connect to wrong WLC

Hello everybody,
I have a problem with some access point.
We have two WLC's one AIR-CT5508-K9 and one AIR-WLC4404-100-K9.
now i have 6 access points that don't register anymore to the right controller.
in high availability i have set the right name of primary controller and also the correct ip address, but somehow they keep registering to the other controller.
Does someone know how i can fix this problem.
info:
AIR-CT5508:SEDA-PM_Line_1
WLC4404: SEDA-PM_Office_1
6 accesspoints are connected to SEDA-PM_Line_1 but they should be connected to SEDA-PM_Office_1
settings in AP are correct in my opinion

here is the information,
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.0.116.0
RTOS Version..................................... 7.0.116.0
Bootloader Version............................... 3.2.195.10
Emergency Image Version.......................... N/A
Build Type....................................... DATA + WPS
System Name...................................... SEDA-PM_Office_1
System Location.................................. Mao, Brazil
System Contact................................... Network_Admin
System ObjectID.................................. 1.3.6.1.4.1.14179.1.1.4.3
IP Address....................................... 105.103.112.5
System Up Time................................... 8 days 15 hrs 9 mins 55 secs
System Timezone Location.........................
Configured Country............................... US - United States
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +38 C
--More-- or (q)uit
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Disabled
Number of WLANs.................................. 13
Number of Active Clients......................... 132
Burned-in MAC Address............................ 00:22:55:91:2B:C0
Crypto Accelerator 1............................. Absent
Crypto Accelerator 2............................. Absent
Power Supply 1................................... Absent
Power Supply 2................................... Present, OK
Maximum number of APs supported.................. 100
(Cisco Controller) >show time
Time............................................. Thu Jan 9 07:58:29 2014
Timezone delta................................... -4:0
Timezone location................................
NTP Servers
    NTP Polling Interval.........................     86400
     Index     NTP Key Index     NTP Server      NTP Msg Auth Status
       1              0        211.189.10.2       AUTH DISABLED
AP information
Warehouse_AP-3#sh version
Cisco IOS Software, C1240 Software (C1240-K9W8-M), Version 12.4(23c)JA2, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Wed 13-Apr-11 12:58 by prod_rel_team
ROM: Bootstrap program is C1240 boot loader
BOOTLDR: C1240 Boot Loader (C1240-BOOT-M) Version 12.4(13d)JA, RELEASE SOFTWARE (fc2)
Warehouse_AP-3 uptime is 18 hours, 16 minutes
System returned to ROM by power-on
System image file is "flash:/c1240-k9w8-mx.124-23c.JA2/c1240-k9w8-mx.124-23c.JA2"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-LAP1242AG-A-K9   (PowerPCElvis) processor (revision A0) with 27638K/5120K bytes of memory.
Processor board ID FTX1233B943
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
LWAPP image version 7.0.116.0
1 FastEthernet interface
2 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:1D:70:96:64:A0
Part Number                          : 73-9925-07
PCA Assembly Number                  : 800-26579-06
PCA Revision Number                  : A0
PCB Serial Number                    : FOC12320AKT
Top Assembly Part Number             : 800-29151-03
Top Assembly Serial Number           : FTX1233B943
Top Revision Number                  : A0
Product/Model Number                 : AIR-LAP1242AG-A-K9
Configuration register is 0xF
Warehouse_AP-3#sh ip interface brief
Interface                  IP-Address      OK? Method Status                Protocol
Dot11Radio0                unassigned      NO unset up                    up
Dot11Radio1                unassigned      NO unset administratively down down
FastEthernet0              105.103.27.19   YES other up                    up
Warehouse_AP-3#sh inventory
NAME: "AP1240", DESCR: "Cisco Aironet 1240 Series (IEEE 802.11a/g) Access Point"
PID: AIR-LAP1242AG-A-K9, VID: V03, SN: FTX1233B943
there are 7 AP's that not register to the right controller some are different models:
Warehouse_AP-1 - AIR-LAP1242G-A-K9
Warehouse_AP-3 - AIR-LAP1242AG-A-K9
Warehouse_AP-5 - AIR-LAP1242G-A-K9
Warehouse_AP-6 - AIR-LAP1242G-A-K9
Warehouse_AP-7 - AIR-CAP3502I-T-K9
Warehouse_AP-9 - AIR-LAP1242AG-A-K9
Warehouse_AP-10 - AIR-LAP1242G-A-K9
Thank you for your help!!

I am having macbook air recently my iphotos did not open and was showing report apple and reopen but i came to know that by pressing alt and iphotos i open an new photo library and stored the pics but now how can i get the pics which i had in the earlier

i am having macbook air recently my iphotos did not open and was showing report apple and reopen but i came to know that by pressing alt and iphotos i open an new photo library and stored the pics but now how can i get the pics which i had in the earlier photo please help me to recover my photos

Well I'll guess you're using iPhoto 11:
Option 1
Back Up and try rebuild the library: hold down the command and option (or alt) keys while launching iPhoto. Use the resulting dialogue to rebuild. Choose to Repair Database. If that doesn't help, then try again, this time using Rebuild Database.
If that fails:
Option 2
Download iPhoto Library Manager and use its rebuild function. (In early versions of Library Manager it's the File -> Rebuild command. In later versions it's under the Library menu.)
This will create an entirely new library. It will then copy (or try to) your photos and all the associated metadata and versions to this new Library, and arrange it as close as it can to what you had in the damaged Library. It does this based on information it finds in the iPhoto sharing mechanism - but that means that things not shared won't be there, so no slideshows, books or calendars, for instance - but it should get all your events, albums and keywords, faces and places back.
Because this process creates an entirely new library and leaves your old one untouched, it is non-destructive, and if you're not happy with the results you can simply return to your old one.
Regards
TD

AIR-LAP1242G

Similar Messages

Maybe you are looking for