Aironet 1252 doesn't broadcast SSID and VLANs

Best regards.
I have an autonomus AP Aironet 1252 (software version: 12.4(18a)JA1)
I configured 3 SSID and VLANs, but the AP doesn't broadcast SSID, the vlans are working fine because I tested configuring manually the hide SSID on laptops.
Also the AP broadcasts the SSID whe only one SSID is configured!!!
How I can do the AP to broadcast all SSIDs?
Thanks in advance.

From the command line of your AP.
Change each SSID as follows.  You want to turn off "guest-mode" and enable "mbssid" at each SSID.  Guest-mode will only broadcast one SSID, you must use mbssid  to allow all SSIDs to broadcast.
#config t
#dot11 ssid
#no guest-mode
#mbssid
Now from each radio
#int d0
#mbssid
#int d1
#mbssid

Similar Messages

  • 2 SSIDs and VLANs on each AP

    I'm new to configuring IOS wireless APs, in particular, a couple of 1142Ns in autonomous mode and looking for examples/answers. These APs will be connected to the POE ports on an ASA 5505 firewall. I'm also configuring the 5505.
    The requirements are that each AP have an "internal" and "external" SSID and each AP will have two VLANS.
    The APs should allow roaming between them.
    The internal SSID will allow full access to internal corporate networks and the Internet and will use WPA2. It will use the corporate dhcp server or employ the IOS dhcp server to hand out addresses.
    The external SSID will only have access to the Internet and will use WEP. The ASA 5505 will provide dhcp services to these clients.
    The two PoE ports on the ASA 5505 will be trunked for both the inside and dmz VLANS.
    If anyone has examples of any of these requirements, comments, and/or similar config they are willing to share, please post them.
    In particular, I would like to see an examples of the roaming config, VLAN config, SSID config, and WPA2 and WEP config.
    Thanks in advance.

    Hi,
    Cisco terms are sometimes Complex!! In English this means.. "broadcasting the SSID or NOT" if you want your laptop to detect the SSID while searching for wireless then this is called BROADCAST if not then NON-BROADCAST.. the command is.. Guest-mode under SSID config.. that is..
    en
    conf t
    dot11 ssid
    guest-mode                           >>>>>>>>>>>> Broadcasting the ssid
    end
    en
    conf t
    dot11 ssid
    no guest-mode                      >>>>>>>>>>>> Not Broadcasting the ssid (HIDDEN) MANUALLY WE NEED TO  ENTER THE SSID ON THE LAPTOP.
    end
    Lemme know if this answered your question..
    Regards
    Surendra
    ===
    Please rate the posts which answered your quiestion or was helpfull

  • P1102W doesn't broadcast SSID & Driver cannot be installed on Mac OS 10.7.5

    Hi,
    I bought a new wifi extender and managed to mess about the settings.  I have no idea how this happened.  
    But the current situation is that P1102W doesn't talk to me because it doesn't broadcast its SSID so I cannot login through its Embedded Web Server.  I cannot connect it through USB to my MacBook Pro either.  I suspect it is because I somehow messed up my driver setting.  But I cannot re-install my driver somehow.
    the machine is on Mac OS 10.7.5.  The printer P1102w is already in its printer list (on wifi but is not connected).  I tried to reinstall driver in order to connect through USB.  But the installation always failed at the last step (mac popped up message suggesting me to talk to software supplier).  I have done "Repair Disk Permissions" a few times. Still the driver doesn't install.  The driver I talk about is "LJP1100_P1560_P1600_Full_Solution.dmg"
    My HP P1102w has been reset to factory default by powering up while pressing the cancel (X) and wifi buttons a few times.  Although its blue wifi light is blinking, it doesn't broadcast its SSID, so I cannot connect to its web based set up page.
    I hope someone out there can help me.  If I failed to provide any necessary information for your diagnosis, please let me know.  Thank you for your help.

    Hi @SillySilly, 
    I see by your post that you have lost the wireless connection with the printer, since setting up a extender. I can help you with this.
    You will have to network the printer to the main network. Make sure there isn't any spaces or special characters in the network name.
    Make sure Safari is set as the default browser. (sometimes the EWS won't open if it isn't set as the default)
    Open Safari, across the top select the Safari menu, select Preferences, General, set as default.
    If you can still print by a USB connection, skip to running the HTML Config section.
    I would run the uninstaller, there might be bits and pieces of the old software still installed.
    Uninstalling the Printer Software.
    Reset the Printing System:
    Note: This will remove all printers in the print and Fax/Scan, any printer removed can be re-added later by clicking the plus (+) symbol.
    Click the Apple icon ( ), and then click System Preferences.
    Click Printers & Scanners.
    Right-click (or Ctrl +click) in the left white side panel, then click Reset printing system.
    Click OK to confirm the reset.
    Type the correct Name and Password.
    Click OK to reset the printing system.
    Connect the printer directly to the Mac.
    Run the downloaded drivers again. HP LaserJet Full Feature Software and Driver.
    If you have any issues with the HTML config opening then do the following steps:
    Close any applications.
    On the Apple menu bar, click Go, computer, MAC harddrive, Library, Printers, HP, LaserJet, click on folder for your printer, click on EWS browser or HTML config, click the Networking tab, click wireless on the left and fill out your information. (make sure infrastructure is selected) Apply settings.
    Then delete the USB driver and add the network printer.
    Please provide in detail the results if you are still having issues.
    Have a nice day!
    Thank You.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

  • SSIDs and VLAN on access points

    The commands to map an SSID to a VLAN on an IOS access point are basically like this:
    [snip]
    dot11 ssid MYSSID
    vlan 5
    interface Dot11Radio0
    ssid MYSSID
    interface Dot11Radio0.5
    encapsulation dot1q 5
    bridge-group 5
    interface FastEthernet0
    interface FastEthernet0.5
    encapsulation dot1q 5
    bridge-group 5
    [snip]
    My question is this: what does the command "vlan 5" actually do? Does it map MYSSID to bridge-group 5, which is then mapped to 802.1q tag 5 by the subinterface configurations (so that the tag number is arbitrary), or does it map MYSSID to 802.1q tag 5 on the radio interface, which is then bridged to the appropriate dot1q subinterface on the wired side by the bridge group (so that the bridge group number is arbitrary)?

    Vlan tag is tied to SSID and Bridge group is also tagged to appropriate vlan mentioned as bridge group number

  • WAP200 setup step by step for 2 SSIDs and VLAN

          I have a Wap200 in a community library environment and wish to set up a pubic open SSID and a private (secure) SSID using two VLANs with trunking to a CISCO RV180W router to force the traffic to be separate and yet allow internet access for both SSIDs.  Does anyone have step-by-step instructions for BOTH the WAP200 setup and the RV180W setup to make this work well.            

    Dear Dennis,
    Thank you for reaching Cisco Small Business Support Community.
    You can have let's say two SSID's with the Wireless Isolation enabled.  Wireless isolation between SSIDs prevents eavesdropping on the network. When it is enabled, wireless frames received on this access point are not forwarded to ther wireless networks (SSIDs).
    The wireless isolation feature should do the job but if you would still like to have VLAN's and a trunk port to the router then he "Wireless > VLAN & QoS" window allows you to configure the VLAN and QoS related settings for the access point, I suggest you to leave the Default VLAN as 1, and untagged, and make sure you use the same setting on the router.  You can even have a higher priority on the private SSID.
    Please refer to the WAP200 admin guide, chapter 6 for further reference;
    http://sen.lla.free.fr/Fichiers/WAP200_Admin_Guide.pdf
    The RV180 VLAN configuration steps please refer to to the admin guide, chapter 2;
    http://www.cisco.com/en/US/docs/routers/csbr/rv180w/administration/guide/rv180w_admin.pdf
    I hope you find this information helpful and please let me know if there is anything I may assist you with.
    Kind regards,
    Jeffrey Rodriguez S. .:|:.:|:.
    Cisco Customer Support Engineer
    *Please rate the Post so other will know when an answer has been found.

  • Trying to setup 1131 in autonomous mode with multiple ssids and vlans

    hi there,
    I'm trying to setup an aironet 1131 in autonomous mode with a WLAN for each VLAN.
    I can connect to the SSID "BLUGstaff" but I don't pick up a DHCP address and when I set a static IP I can't anything on the vlan so I can only assume I have made an error.
    I have attached the config for the access point.
    The switch port the access point connects to has the following config...
    interface FastEthernet1/0/3
    description ## Access Point ##
    switchport trunk encapsulation dot1q
    switchport trunk native vlan 121
    switchport trunk allowed vlan 1,121-124
    switchport mode trunk
    spanning-tree portfast
    end
    Can anyone explain what I've done wrong? Thanks in advance for any help,
    Huw

    Hello Huw,
    as i see in your confirguartion.
    native VLAN is 121. so you have to correct following in your AP configuration
    1) interface Dot11Radio0.121
    encapsulation dot1Q 121 native
    bridge-group 121         ->>>>>>>>>>>>>>>> change this to brige-group 1 , native always tied to bridge group 1
    2)
    interface FastEthernet0.121
    encapsulation dot1Q 121
    add also under this sub interface
    bridge-group 1
    please let me know how it goes.
    Kind regards
    Talal
    ==========
    please rate answers that you find useful , and mark as answered - when it is :-) - so others can find it easily

  • Configuring ssid and vlans on autonomous access point ?

    here is an a demonstration of how to configure vlans and ssid on a auto-ap , what i dont understand is when i configure the ssid under (interface dot11radio0) and the vlan under that command , why do i need to configure sub-interfaces for the "fastethernet" and the "dot11radio0" if i already configured it under the "interface dot11radio0" , why do i need the "encapsulation dotq x" ? and what is bridge-group ?

    If you want to use multiple SSID with multiple vlan, then you have to configure subinterfaces on Radio interfaces (in both Radio 0 & Radio 1 if you want to use both 2.4GHz & 5GHz band) & Ethernet interfaces.
    AP simply bridge wireless traffic to wired interface using these sub-interfaces. To specify which radio sub-interface traffic to map to ethernet sub-interface, a Bridge-Group number (1-255) is used.
    Bridge-Group 1 always used for native vlan traffic & usually used for AP management.
    HTH
    Rasika
    **** Pls rate all useful responses ****

  • Automomous AP not broadcasting SSID and can I get it to support both WPA and WPA2?

    Ok, I am playing around with a 3702i that has been converted to Autonomous running ap3g2-k9w7-mx.153-3.JAB
    I have 2 issues I have not been able to solve yet.   I have basically set it up using the web interface....
    First, I can't get the SSID to broadcast -- the SSID is active, because I can type it in manually.
    Second, I have an HP 8600 Pro All-in-One printer that I normally connect over WiFi.  Basically, it does not seem to support WPA2...I spent most of yesterday pouring through HP forums and WPA2 support seems to be a issue.  My old Linksys router had a setting that supported WPA/WPA2...does anyone know how or if I can support WPA / WPA2 simultaneously on this Autonomous AP?
    Here is my config:
    Thanks....
    Cisco3702#sh run br
    Building configuration...
    Current configuration : 3867 bytes
    ! Last configuration change at 12:44:59 -0500 Tue Mar 9 1993
    ! NVRAM config last updated at 11:29:23 -0400 Sat Oct 18 2014
    ! NVRAM config last updated at 11:29:23 -0400 Sat Oct 18 2014
    version 15.3
    no service pad
    service timestamps debug datetime msec
    service timestamps log datetime msec
    service password-encryption
    hostname Cisco3702
    logging rate-limit console 9
    no logging console
    enable secret 5 XXXXXXXXXXXX.
    no aaa new-model
    clock timezone -0500 -5 0
    clock summer-time -0400 recurring
    no ip source-route
    no ip cef
    ip domain name mydomain.com
    ip name-server 192.168.6.254
    dot11 syslog
    dot11 activity-timeout unknown default 300
    dot11 activity-timeout client default 300
    dot11 ssid MYSSID
       band-select
       authentication open
       authentication key-management wpa version 2
       infrastructure-ssid
       wpa-psk ascii 7 XXXXXXXXXXXX
    dot11 network-map
    dot11 arp-cache optional
    crypto pki trustpoint TP-self-signed-2632604960
     enrollment selfsigned
     subject-name cn=IOS-Self-Signed-Certificate-2632604960
     revocation-check none
     rsakeypair TP-self-signed-2632604960
    crypto pki certificate chain TP-self-signed-2632604960
     certificate self-signed 01
    username CISCO password 7 XXXXXXXX
    username ADMIN privilege 15 secret 5 XXXXXXXXXXXX
    bridge irb
    interface Dot11Radio0
     no ip address
     encryption mode ciphers aes-ccm
     ssid MYSSID
     antenna gain 0
     stbc
     speed  basic-11.0 basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15. m16. m17. m18. m19. m20. m21. m22. m23.
     channel 2412
     station-role root access-point
     dot11 qos class video local
        admission-control
        admit-traffic signaling infinite
     dot11 qos class voice local
        admission-control
        admit-traffic narrowband max-channel 75 roam-channel 6
     dot11 qos class video cell
        admission-control
     dot11 qos class voice cell
        admission-control
     bridge-group 1
     bridge-group 1 subscriber-loop-control
     bridge-group 1 spanning-disabled
     bridge-group 1 block-unknown-source
     no bridge-group 1 source-learning
     no bridge-group 1 unicast-flooding
    interface Dot11Radio1
     no ip address
     encryption mode ciphers aes-ccm
     ssid MYSSID
     antenna gain 0
     peakdetect
     dfs band 3 block
     stbc
     speed  basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15. m16. m17. m18. m19. m20. m21. m22. m23. a1ss7 a2ss7 a3ss7
     channel dfs
     station-role root access-point
     dot11 qos class video local
        admission-control
        admit-traffic signaling infinite
     dot11 qos class voice local
        admission-control
        admit-traffic narrowband max-channel 75 roam-channel 6
     dot11 qos class video cell
        admission-control
     dot11 qos class voice cell
        admission-control
     bridge-group 1
     bridge-group 1 subscriber-loop-control
     bridge-group 1 spanning-disabled
     bridge-group 1 block-unknown-source
     no bridge-group 1 source-learning
     no bridge-group 1 unicast-flooding
    interface GigabitEthernet0
     no ip address
     duplex auto
     speed auto
     bridge-group 1
     bridge-group 1 spanning-disabled
     no bridge-group 1 source-learning
    interface BVI1
     mac-address 58f3.9cea.5d20
     ip address 192.168.6.253 255.255.255.0
     ipv6 enable
    ip forward-protocol nd
    ip http server
    ip http secure-server
    ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
    snmp-server view dot11view ieee802dot11 included
    snmp-server community public view dot11view RO
    snmp-server location Home
    snmp-server chassis-id Cisco3702i
    bridge 1 route ip
    line con 0
    line vty 0 4
     login local
     transport input all
    sntp server 173.255.227.205
    sntp broadcast client
    end

    Hi
    You have to add "guest mode" command to broadcast your SSID. Also if you need WPA/TKIP support then remove version 2 keyword under SSID & add TKIP option under radio interface encryption config. Also get rid of "infrastructure SSID" command under SSID config.
    dot11 ssid MYSSID
       band-select
       authentication open
       authentication key-management wpa version 2
       infrastructure-ssid
       wpa-psk ascii 7 XXXXXXXXXXXX
      guest mode
    interface Dot11Radio1
     encryption mode ciphers aes-ccm tkip
    Pls do not forget to rate all useful responses 
    HTH
    Rasika

  • SSID and Vlans

    I can to have two SSIDs for all branch of my country, but each ones in a differents subnets,for example:
    Area 1
    SSID 1 : guest -> 192.168.1.1
    SSID 2 : office -> 192.168.2.1
    Area 2
    SSID 1 : guest -> 192.168.3.1
    SSID 2 : office -> 192.168.4.1
    I have configured AP-Group, and this works succesfull but only with one SSID, I need two SSID, each one associated a multiples vlans, when the user are connect to SSID guest they receive the correct ip from the subnet corresponding,(Area1 ip address of host is 192.168.1.X and the Area 2 the usuer receibe the address 192.168.3.X both using the same SSID "guest"), How I can reach this requerimients using two SSID?. Using Ap-Group or there is other methods.

    AP Group VLANs are used in a setup where a Universal WLAN (service set identifier [SSID]) is required but clients need to be differentiated (placed on different interfaces configured on the WLC) by virtue of physical LAPs they associate with. Refer URL
    http://cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008073c723.shtml#c2

  • Broadcast and non-broadcast SSID issues with iPhones and iPads

    We have a CIsco wireless infrastructure configured with a public broadcasted ssid and a private non-broadcast ssid that we are experiencing issues with the iPads and iPhones.  The iPad or iPhone will switch between both ssids if defined but keep the original IP address when it switches to the non-broadcast ssid making it unusable.  It shouldn't be switching at all technically.  If the non-broadcast ssid is defined only on the iPhone or iPad, the broadcast ssid pops up and starts asking for authentication information.  I have Cisco looking into this but I'm quite sure this is an Apple bug. Any other device works fine.  We are currently using version 4.3.5(8L2) on the iPads and iPhones.  I do know that if we broadcast both SSIDS, the issue goes away, but I don't want to do that.  Although it doesn't really add any more security, it just isn't advertised, so most people won't see it and avoids a lot of questions. Hopefully there's a simple solution. 
    Any ideas apple guys?
    Also how does one open an actual trouble ticket with apple?

    Did you solve this?  Settings\Wifi\Askto join networks - OFF

  • WLC2112 with Guest / Web-Auth and vlan

    Hi
    I'm trying to configure my WLC with guest SSID and vlan 10.
    The security is only set to Web-auth, and it is all working if the guest network is set to nativ vlan (1) But it seems that the http(s)://1.1.1.1/login.html is not reacheble from the guest SSID/VLAN??
    Please help.
    Management IP Address 192.168.14.252
    Software Version 6.0.182.0
    Emergency Image Version
    I have tried with ver. 5.2 also -

    I think that 1.1.1.1 is only reachable from a wireless client during webauth. They should not be able to reach that address once they have passed through the web auth page.
    Don't know if that helps, or not.

  • Non-broadcast ssid = no beaconing?

    We were told that even though Cisco AP's can support a ton of different ssid's, it's a good idea to keep that number to minimal, due to the fact that each ssid becons to the lowest data rate.
    Does anyone know what the recommended max. number of SSID is?
    Also if we simply make the SSID non-broadcast, does the AP still send becon out for that non-broadcast ssid, and therefore make it somewhat better?

    Lets be clear what a broadcast is and a beacon is ...
    Aps need to beacon. If they do not beacon they dont work cause clients will not know where to find them. With that being said, if you enable 16 SSIDs you will have 16 beacons. These are virtual btw. Also they will all use medium.
    If you want to know about the virtual beacons and cisco check out my blog post:
    http://www.my80211.com/home/tag/cisco-virtual-mac-address
    Broadcast / Hide your SSID
    There is a field in the beacon that holds your WLAN SSID. You can either hide this or reveal it. If you hide it you lessen the chance of devices finding it. But as Surendra pointed out there is no real security. Becuase there are ways to get the hidden ssid.
    So if you hide it or no, no impact to your medium at all.. Why, beacuse the APs still need to beacon ..
    Make sense now bud?

  • Ssid's vlan's ip address

    have a problem there would ap ssid and vlan other's want to link that I use for my final finish work, get no ip address problem
    how can you fix this

    I have a problem to get high on wireless ee ssid, but get no ip address on the host's anyone knows how to fix them

  • Cisco Aironet AIR-SAP2602I-E-K9 WAP -ERROR: VLAN 1000 doesn't exist on 'Radio1-802.11N 5GHZ' (see Services VLAN)

    Hey guys,
    I'm configuring my access points with two SSID's through the GUI. The first is a corporate SSID and the second a guest SSID. The corporate SSID needs to be attached to native VLAN 1000. The guest SSID needs to be attached to VLAN 1234. Both SSID's / VLAN's are to use WPAv2 AES CCMP with a PSK. Although I'm getting an error message indicating that my VLAN's don't exist on ‘Radio1-802.11N 5GHZ’ .  Here are steps I take from start to error...
    Create SSID’s with no security. CORP not to broadcast. Set CORP to use native VLAN 1000. Set guest to use VLAN1234.
    Within security encryption manager > Set encryption mode cipher to AES CCMP on both VLAN 1000 and VLAN1234.
    Within services > VLAN check that both VLAN’s have Radio0-802.11N 2.4GHZ and Radio1-802.11N 5GHZ selected. They do.
    Within Security > SSID Manager – set client authenticated key management to mandatory, enable WPA – WPAv2. Set pre-shared key. Hit apply > “ERROR: VLAN 1000 doesn’t exist on ‘Radio1-802.11N 5GHZ’ (see Services > VLAN).
    I get the same error for both SSID’s. Radio1-802.11N 5GHZ is "checked" against both VLAN's. Am I missing something? Both Radio0-802.11N 2.4GHZ and Radio1-802.11N 5GHZ are enable interfaces and are "up".
    I'm pretty customed to switch and router IOS although have absolutely no exposure to WAP CLI.
    Any assistance appreciated.

    I've resolved this myself. The GUI is basically terrible and very buggy. I used the CLI and was able to add WPA through the CLI.

  • Aironet 1252 DHCP with vlans

    I have an aironet 1252 access point and I have it set up with 3 ssid's which in turn are 3 separate vlans. My question is, can the 1250 supply dhcp to each ssid or only to the native vlan. This access point is going to be connected to a 4507 routing switch. Currently I am unable to obtain any dhcp addresses. The port that the access point is connected to is a trunk port and is configure to only allow the 3 vlans that are on the access point. Any help would be greatly appreciated

    Hi, rgonzalez_tec
    Can you verify that the other two VLANs' DCHP mode is set to DCHP Server and that for each IP address, port based authentication is enabled?
    I have found three documents on the knowledge base that may help you in the right direction.
    Enabling Multiple Wireless Networks on RV320 VPN Router, WAP321 Wireless-N Access Point, and Sx300 Series Switches
    DHCPv4 Configuration and Monitoring on RV32x VPN Router Series
    DHCPv6 Configuration and Monitoring on RV32x VPN Router Series
    More documents can be found using the GuideMe tool here.
    -Andy

Maybe you are looking for