Cisco Aironet AIR-SAP2602I-E-K9 WAP -ERROR: VLAN 1000 doesn't exist on 'Radio1-802.11N 5GHZ' (see Services VLAN)
Hey guys,
I'm configuring my access points with two SSID's through the GUI. The first is a corporate SSID and the second a guest SSID. The corporate SSID needs to be attached to native VLAN 1000. The guest SSID needs to be attached to VLAN 1234. Both SSID's / VLAN's are to use WPAv2 AES CCMP with a PSK. Although I'm getting an error message indicating that my VLAN's don't exist on ‘Radio1-802.11N 5GHZ’ . Here are steps I take from start to error...
Create SSID’s with no security. CORP not to broadcast. Set CORP to use native VLAN 1000. Set guest to use VLAN1234.
Within security encryption manager > Set encryption mode cipher to AES CCMP on both VLAN 1000 and VLAN1234.
Within services > VLAN check that both VLAN’s have Radio0-802.11N 2.4GHZ and Radio1-802.11N 5GHZ selected. They do.
Within Security > SSID Manager – set client authenticated key management to mandatory, enable WPA – WPAv2. Set pre-shared key. Hit apply > “ERROR: VLAN 1000 doesn’t exist on ‘Radio1-802.11N 5GHZ’ (see Services > VLAN).
I get the same error for both SSID’s. Radio1-802.11N 5GHZ is "checked" against both VLAN's. Am I missing something? Both Radio0-802.11N 2.4GHZ and Radio1-802.11N 5GHZ are enable interfaces and are "up".
I'm pretty customed to switch and router IOS although have absolutely no exposure to WAP CLI.
Any assistance appreciated.
I've resolved this myself. The GUI is basically terrible and very buggy. I used the CLI and was able to add WPA through the CLI.
Similar Messages
-
Cisco Aironet AIR-SAP2602I-E-K9 - Setting QoS from CLI...
Hey guys,
I've created a QoS policy from within the GUI. However when trying to apply the policy to all incoming and outgoing interfaces of the VLAN concerned (1000 / CORP) from within the GUI I'm not convinced it is working. I select the policy against each interface and hit "apply" and then it defaults back to no policy being selected. Looking at show run I can see the policy is created although I'm not convinced it has been applied to the interfaces? Could somebody please take a quick glance at the config below and indicate whether the policy has been applied to the interfaces for VLAN 1000. Pretty sure it hasn't.
User Access Verification
Username: admin
Password:
LATHQWAP#show run
Building configuration...
Current configuration : 3456 bytes
! Last configuration change at 00:38:43 UTC Thu Mar 4 1993 by admin
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname LATHQWAP
logging rate-limit console 9
aaa new-model
aaa authentication login default local
aaa authorization exec default local
aaa session-id common
no ip routing
dot11 syslog
dot11 vlan-name Data vlan 1000
dot11 vlan-name Guest vlan 1234
dot11 ssid Corp
vlan 1000
authentication open
authentication key-management wpa version 2
wpa-psk ascii 7
dot11 ssid Guest
vlan 1234
authentication open
authentication key-management wpa version 2
guest-mode
wpa-psk ascii 7
crypto pki token default removal timeout 0
username admin privilege 15 password 7
class-map match-all _class_Lync0
match ip dscp cs5
policy-map Lync
class _class_Lync0
set cos 6
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 1234 mode ciphers aes-ccm
encryption vlan 1000 mode ciphers aes-ccm
ssid Corp
ssid Guest
antenna gain 0
stbc
station-role root
interface Dot11Radio0.1000
encapsulation dot1Q 1000 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.1234
encapsulation dot1Q 1234
no ip route-cache
bridge-group 255
bridge-group 255 subscriber-loop-control
bridge-group 255 spanning-disabled
bridge-group 255 block-unknown-source
no bridge-group 255 source-learning
no bridge-group 255 unicast-flooding
interface Dot11Radio1
no ip address
no ip route-cache
encryption vlan 1234 mode ciphers aes-ccm
encryption vlan 1000 mode ciphers aes-ccm
ssid Corp
ssid Guest
antenna gain 0
no dfs band block
stbc
channel dfs
station-role root
interface Dot11Radio1.1000
encapsulation dot1Q 1000 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio1.1234
encapsulation dot1Q 1234
no ip route-cache
bridge-group 255
bridge-group 255 subscriber-loop-control
bridge-group 255 spanning-disabled
bridge-group 255 block-unknown-source
no bridge-group 255 source-learning
no bridge-group 255 unicast-flooding
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
interface GigabitEthernet0.1000
encapsulation dot1Q 1000 native
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
no bridge-group 1 source-learning
interface GigabitEthernet0.1234
encapsulation dot1Q 1234
no ip route-cache
bridge-group 255
bridge-group 255 spanning-disabled
no bridge-group 255 source-learning
interface BVI1
ip address 10.10. 255.255.254.0
no ip route-cache
ip default-gateway 10.10.
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
line vty 0 4
transport input all
end
Thank you to anyone taking the time to assist. Greatly appreciated - very new Cisco wireless tech.
Cheers.Sorted this myself. It wouldn't apply to the VLAN because VLAN 1000 was the native VLAN.
-
ORA-01041: internal error. hostdef extension doesn't exist
hi all,
i am presently working on logical standby database
but i am facing a problem from primary database
" select * from V$ARCHIVE_DEST"
LOG_ARCHIVE_DEST_1 valid
LOG_ARCHIVE_DEST_2 ERROR ORA-01041: internal error. hostdef extension doesn't exist
at present database not synchronizing
please help
in alert.log file at primary
ARC9: Attempting destination LOG_ARCHIVE_DEST_2 network reconnect (1041)
ARC9: Destination LOG_ARCHIVE_DEST_2 network reconnect abandoned
PING[ARC9]: Error 1041 when pinging standby 'standby server'.
Standby database is in running mode & well connected with network
Vaibhav
Edited by: Vaibhav Dixit on Oct 20, 2011 4:43 PM
Edited by: Vaibhav Dixit on Oct 20, 2011 4:43 PMokkk
thanks for reply
i m also getting some problem in standby database in just 2-3 days
error is ->
ORA-03135: connection lost contact
LOG_ARCHIVE_DEST_2 ERROR ORA-01041: internal error. hostdef extension doesn't exist
then
i have passed some command on primary db & now it's working but i don't know it's good for db or not
ALTER SYSTEM SET log_archive_dest_state_2=’DEFER’ SCOPE=BOTH;
ALTER SYSTEM SET log_archive_dest_state_2=’ENABLE’ SCOPE=BOTH;
please give a idea to resolve this problem
regards
Vaibhav -
Error message Address doesn't exist 24593 in t-code va01,va02,va03
Hi Friends,
After entering order in T-code va03 i get the error message Address doesn't exist 24593 .
please guide
thanks in advance,
regards.
BhaskarCheck your ship-to Party.
Also read the S-note 865271 -
Subcontracting Challan Error *showing error "The document doesn't exist"*
Dear Gurus,
When i run T-code j1ifq for quantity reconcilation for subcontracting challan .then i enter Mat. Doc(GRN document) and fiscle year 2009 and run F8 it's
showing error "The document doesn't exist" but it exist in system.How to resolve this problem pl provide needful method to solve this issue.
Thanks
Abhinavhi,
have you typed the challan no or selected from the F4 list? please check that and the year of the challan document. then you should not have this error. -
System throwing error " ibase object doesn't exist"
Dear Friends;
in the transaction ib52 when im putting the component number and pressing enter the system is showing me the error
"ibase objec doesn't exist" . Which means system not allowing to search ibase using the component number.
Please help.
shibashish banerjeeDear Denis,
When I'm putting the component and pressing enter the system should automatically display the ibase related to this component right?
Instead of this the system is throwing me the error " ibase object does'nt exist" . which i feel is incorrect . As per me system should automatically show me ibase , when i enter the component number and press enter.
I checked in ibib and ibin tables as well. No conclusion.
Regards
shibashish banerjee -
BI Installer issue with message" Error: ABAP Backend doesn't exist in SLD
Dear All
Please help me to solve this issue, during the BI Installer the process get errors message
"Error: ABAP Backend doesn't exist in SLD"
Follwoing the oss Note 983156 - BI configuration w. Template Installer
1.Logon to the SLD: http://<host>:<port>/sld. (Your configured SLD (central or local SLD))
Please check in Home -> Technical Systems -> select type ABAP. This
should have configuration of your ABAP (BI) system. yes the system already there.
2, goto http://host:port/index.html ->Web Dynpro ->Content Administrator-> Check SLD Connection
the connection is running well.
Please any one can help me to solve this issue,
Thanks and Best Regards,
ChrisnaHi
I found your question because I wanted the answer to it too. I'm trying to connect my Java-only stack portal to my ABAP-only stack BI system using the template in NWA. I get through all the steps up to the creation of the WebDynpro JCO RFC destinations then it fails saying "ABAP Backend doesn't exist in the SLD".
I've checked the SLD and the ABAP backend most definitely DOES exist in the SLD and the SLD is being updated by both the ABAP backend and the Java portal systems thus proving a valid connection exists between the SLD and both systems I'm trying to connect.
I think I've solved it however.
I always define a TCP alias equal to the SID for any SAP system I build and I try to make all connections to <sid>.<fully.qualified.domain.name>. This separates, to a degree, the physical server from the SAP instance.
I used this alias in the BI installation template but I noticed that the ABAP backend was listed as <SID> <hostname> in the SLD (not <SID> <sid alias>). When I used the real hostname in the template it ran to completion.
The other change I made, and it's possible that this was the real reason instead of the alias/hostname issue, was that I restarted the BI system before retrying. I only did this because I was getting error messages saying there were too many active CPIC conversations and I couldn't find them to kill them off.
Hope one or other of these things might help.
Murray -
Error: Startup task doesn't exist. This is not a continuation after a restart
I want to try to install sharepoint 2013 on windows server 2008 r2 with sp1, but when I install the prerequistes, always restart again and again, I check the log file, found the below error:
2014-02-27 22:55:12 - C:\ProgramData\Microsoft\Windows\Start Menu\Programs\Startup\SharePointServerPreparationToolStartup_0FF1CE14-0000-0000-0000-000000000000.cmd
2014-02-27 22:55:12 - Error: Startup task doesn't exist. This is not a continuation after a restart.
2014-02-27 22:55:15 - Error: The tool was unable to install Application Server Role, Web Server (IIS) Role.
2014-02-27 22:55:15 - Last return code (0X3EC=1004)
2014-02-28 03:27:05 - Error: A pending restart blocks the installation
2014-02-28 04:45:03 - C:\ProgramData\Microsoft\Windows\Start Menu\Programs\Startup\SharePointServerPreparationToolStartup_0FF1CE14-0000-0000-0000-000000000000.cmd
2014-02-28 04:45:03 - Error: Startup task doesn't exist. This is not a continuation after a restart.
2014-02-28 04:45:03 - Locating the following command line arguments file:
2014-02-28 04:45:03 - C:\SP2013_Chery\2Installation\Sharepoint\PrerequisiteInstaller.Arguments.txt
2014-02-28 04:45:03 - Error: This file does not exist
AwenHi Awen,
According to your description, my understanding is that you got an error when you installed prerequisities for SharePoint 2013.
Please run the following command, compare the result:
C:\Windows\Microsoft.NET\Framework64\v4.0.30319\aspnet_regii -enable –i
Here is a similar post for your reference:
http://social.technet.microsoft.com/Forums/sharepoint/en-US/37cc20db-6cc7-45e0-928c-9a1ddbdab2ae/the-tool-was-unable-to-install-application-server-role-web-server-iis-role?forum=sharepointadmin
In addition, there is a KB article about this issue, please take a look at:
http://support.microsoft.com/kb/2765260/en-us
I hope this helps.
Thanks,
Wendy
Forum Support
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact
[email protected]
Wendy Li
TechNet Community Support -
FND-UT-CMT: ORA-01041: internal error. hostdef extension doesn't exist
I am applying patch PO RUP 22, after merging patch->10207297,11669329,7632187,9878808. However for 1 file -INVITPSB.pls, i am getting status running, but in the adorker log file shows ->
AD Worker error:
The following ORACLE error:
ORA-03114: not connected to ORACLE
occurred while executing the SQL statement:
UPDATE fnd_install_processes
SET skip_flag = ''
WHERE worker_id = 1
Error comitting pending transactions and closing Pro*C connection.
The error is:
FND-UT-CMT: ORA-01041: internal error. hostdef extension doesn't exist
AD Worker is exiting with failure.
Any ideas of what can be done?HI,
Please check if solution in below metalink note helps:-
Patch 4143498 Fails With ORA-01041,ORA-03114 Errors On Iscrf70b.Pls ORA-01041 [ID 340238.1]
Thanks,
JD -
Cisco Aironet Air-Ap 1262n-E-K9 Mac different when Scanned Android WiGLE WiFi
Hi All
I developed an Android Application to scan for the RSSI signals using the mac address of the Access Point (AP). When I do a scan for my personal Vodafone router or my personal dLAN 500 WiFi, I can pick up the mac address and get the signal levels from that.
When I try do the same for the Cisco 802.11n Dual Band Access Point, Aironet Air-Ap 1262n-E-K9 the app will not pick up the routers mac that is on the label on the back. I downloaded the free WiGLE WiFi app and Scanned with it and it too doesn't give the mac I am looking for, what it does give me is six mac address 3 on channel 11 and 3 on 44 with the RSSI values.
My Question: Is the mac address on the Cisco AP label just for the LAN and the WiFi antennas have each got a separate mac 3 on the 2.4GHz and 3 on the 5GHz.
Can someone help me better understand this problem I am having, I hope I have explained it well enough for you to understand what I am trying to do.what it does give me is six mac address 3 on channel 11 and 3 on 44 with the RSSI values.
Each SSID has it's own unique MAC address. This is the original standard.
The MAC address printed at the back of an AP is the MAC address in Ethernet. -
When creating po, pop up error message 'address doesn't exist'.
when creating po via me21n, when click delivery tab screen, pop up error message dialog box 'address doesn't exist T001 wsu20 00010'. message no is 'am010'. then i was forced to exit transaction.
ps: 'su20' is my plant, but in me21n, when selecting plant, i can see two 'su20', the diffrence is International address version. why there is two same plantgo into customizing and maintain an adress by clicking the envelope button in the detail to the plant. The adress in the customizing views itself is not sufficient.
-
Error message "Address doesn't exist "
Dear Experts,
In ME23n, when i give some purchase order and click on ADDRESS tab it is giving the error message as "'Address doesn't exist 51457447 4601225079"", And when i check the address in ADRC table for the same vendor via ADRNR number it is providing the address
And also it displays the address in the smartform preview.
But same is not populated in the ADDRESS tab.
Anybody help
Regards,
Venki....Venki,
I once had exactly the same problem and message. It turned out that the error message was misleading..
In my case, a (custom) function module was returning an exception WITHOUT specifying a message. Subsequently the calling program also returned an exception, and simply reported the last message sitting in the SYST structure.
I recommend you set a breakpoint on the MESSAGE statement when debugging.
cheers
Paul Bakker -
ORA-01041: internal error. hostdef extension doesn't exist in forms 10g
While Compiling the forms 10g I'm getting this error, pls help me on this problem.
Check this link... ORA-01041: internal error. Hostdef extension doesn't exist
hope this helps -
FPCOPARA ERROR. Address doesn't exist
Hi Experts,
When i want to print a welcomes letter i get the error Address doesn't exist. Does some know why this message appear and how to solve it?
I've looked in the table ADRC en found out the the spefic address for that addressnumber is marked as a Maintenance object address.
This specific number is not linked to the business partner in the table BUT021_FS. In this table I found that the BP is linked to another address number that have the same city, street, zip-code etc. as the one that mared as Maintenance object address but this is marked as Business partner (customer, supplier).
Kind regards,
R.L.GroenerHi,
Most likely master data is incomplete. Run that program with the same variant online and set a break-point on 'message' statement to find out where the problem is. -
Does anyone know if the macbook air supports 802.11n 5Ghz ?
Does anyone know if the macbook air supports 802.11n Ghz ?
Every MacBook Air supports 802.11 a/b/g/n and the 2013 models added 802.11 ac
Maybe you are looking for
-
How do i upload pictures from iphone to mac air I have iphoto and did it before but cannot figure out what I am doing wrong ?
-
Any ideas on where to get a reasonably priced SSD in Aussie?
I have no experience with hardware but I want to get a 2.5 inch SATA SSD to replace a HDD in my 2011 winter/fall MBP. Any ideas on where to get one in Australia for a reasonable price? I'm looking for about 550GB give or take.
-
Can you please let me know what is ABAP Stack
-
Hi experts, I'm facing a problem when I try to show a matchcode of dates. I get the date records on the value_tab internal table, the matchcode window says that there are entries but it does not show the values. Maybe it's a silly mistake, but I can'
-
LSMW Direct Input Inspection Plan Not Writing Inspection Char File
Hello Experts, I am using Direct Input Program RCPTRA01 to Load Inspection Plan. Created 3 structures - Inpection Plan/Operations/Inspection Characteristics one below the other in that order. We have a internal numbering system for assigning Group