Airport Express access over 'Extended' network (Time Capsule)

Hello everyone,
I've seen several posts similar to this, and I've come pretty far in figuring this out but the final roadblock is scratching my head.
I purchased an Airport Express a few days ago to get my xbox 360 onto the internet without running a wire and without giving Microsoft my 100 dollars. I had it working under WDS but WDS trashed my network speed. I found out about the 802.11n version of 'extending' the network tonight. Got it all setup, so much easier than WDS!
So I slap my xbox 360 ethernet cable into the Airport Express and go to watch some Netflix. Turns out I can't get to the internet...I've got the thing on the network. It's got an IP, subnet looks good, gateway looks good.
I tried to ping it from my iMac and I can't get to it.
My network looks like this...
FIOS -----> Actiontek Router --(Bridge)--> Time Capsule --(extended network)--> Airport Express ---(ethernet) --> Xbox360
Thanks for any help,
Cheers.

Hi
When you try and ping the Xbox where are you doing it from, i.e. do you have a laptop that is a wireless client of the TC? What IP address is your XBox getting? What IP address is on the station that you are pinging from? What is the IP address of the Express itself? Can you ping the Express?
You mention that the Express has a solid green led right? What if you move the laptop to be ethernet client of the Express, can the laptop now access the internet?
cheers

Similar Messages

Airport Express as wireless Extender to Time Capsule

I have an older airport express that I used to use as an Wifi extender for my Time Capsule. I have a Macbook Pro running Os 10.8.4, and the airport utility now gives the following error:
This version of AirPort Utility doesn’t support this base station. Go to AirPort Service and Support for more information.
Since OS 10.8 does not support Airport Express 5.6, I have an old Mac I've been able to access Airport Express on and was able to ensure that everything was setup correctly as a wireless extender. However, None of my computers, Ipads, or Iphones are benefitting from this as an extender. Is it possible to use this older airport express as an extender still or has Apple completely blocked me from using it even as that any longer? It used to work fine, until I updated the OS from 10.7 to 10.8, and now it no longer functions.
Thank you!

That article addresses installing AU 5.6 on a Mountain Lion system, not the ability to "wirelessly extend" an 802.11b/g - only Express. That ability is available for 802.11n - capable base stations only:
Multiple Wi-Fi base station network types
If you need to extend the range of your wireless network, which method should you use?
For 802.11a/b/g/n Wi-Fi base stations:
Roaming Network (Recommended)
Wirelessly Extended Network
For 802.11g Wi-Fi base stations:
Roaming Network (Recommended)
WDS
Which of the above configurations applies to your network?

HT4145 I want to add airport express. I now have time capsule and I am confuse. Do I setup the express and then time capsule to the express?

I want to add airport express. I now have time capsule and I am confuse. Do I setup the express and then time capsule to the express?

Setup the Express to wirelessly extend the Time Capsule, or vice versa depending on which one is already set up. Or you could use bridge mode which involves using an Ethernet cable or Powerline plugs.

Airport express keeps loosing connection to Time Capsule

For several years I have had no issue with mt Airport Express staying connected to my Time Capsule/router. Now 2 of my Airport Expresses keep loosing the connection and flashing yellow. I have done the resets where I press in the little button on the bottom while plugging the AE back into the power source and reconnecting through Airport Utility and that will do the trick but after a short time the flashing yellow lights will go back on.
Would it help to turn off the router, rest all the AEs? It is so frustrating to keep loosing the connection and nothing else has changed; e.g. the AEs are all in the same place.

Same thing here! I didnt have the problem with airport express until I update the os from 10.6.2 to 10.6.6. I have been calling the apple support and they couldnt help (or thou sounded like they knew for that particular problem). I got from my work MacBookPro and same thing happen. I hope that apple will read this and just want to tell them that this is my 10 computer made by apple and God knows the last one! First of all they made the the fireware with the bad chipsets so I have to but extra cards and then airport. I cant connect at all to any wifi and have to put the cables on the floor from the wifi router to the ethernet input which is more than 10 metres. Apple sort this asap!!!!!!!!!!

Airplay not working on Airport Express N in Extended Network

Hi
I have a setup as in the diagram below. Internet Router connected to my Airport Express N which creates a N-class network. Then I have an Time Capsule in another room that extends this network. My iMac is connected to this Time Capsule using Ethernet (WiFi is turned off completely).
iTunes is 10.6.1 (7)
Airport Express and Time Capsule have the latest firmware (v7.6.1)
Internet, sharing and other functions are working fine, just Airplay from the iMac doesn't work anymore to the Airport Express. I've tried lots of solutions, and this just seems to be broken. I've submitted to Apple feedback as well explaining the situation and that this doesn't work.
If I add/remove a password or enable/disable airplay on the Express, it does reflect in iTunes. It also shows that the Airplay is locked/unlocked (see image) and also shows it as a visible audio destination. But when you activate it from iTunes, it doesn't ask for any password (if enabled), but it just displays the "connecting" dialog for about 1 minute and then closes the window without any error and just does nothing. It's like iTunes cannot communicate to the Airport Express, although at the same time I can connect to it's internal configuration (edit) and also connect to the internet, my router's config using a browser, etc. without any problems. Also, if I'm using my iPad and iPhone, I can easily use the Airport Express from those devices, but NOT from the iMac.
I'm thinking Apple broke Airplay in this type of scenario.
Anyone with any ideas. I have a big hot paperweight called an Airport Express plugged into the wall in my bedroom now.

My problem is similar but not always the same. I have a Time Capsule extended by an Airport Express which in turn is connected to my hifi. My Imac is connected to the TC by Ethernet alone - no wifi. The connection from the TC to my AE is done by a mains wiring ethernet connection which works superbly for TV streaming etc. However, sometimes when I try to connect to the AE for music, I get an error message whicg says that is not possible to connect to the Airplay device. If I restart the Imac, it connects immediately and without problem and will run for as long as I want. Once stopped, I then get the error messge again until I restart.

Airport Express can only extend network, not create new one. Why?

I am sharing a flat with some friends. The shared broadband router is placed in the living room. To strengthen the signal and make it easier for me to manage, I bought an Airport Express, connected it to the shared router with an ethernet cable and set up a wireless network of my own in my room. It was working fine, until recently we renewed our broadband contract. The router had been replaced by a new one (I don't know why) and the network configration had been changed. Since then I was not able to use my own network. In the Airport Utility display, the light of Airport Express is green, but the light of Internet is yellow, and the status is disconnected. I tried to change various other configuration on the Airport Express, and all in vain. Until I switched the network mode from 'Create a new wireless network' to 'Extend a wireless network', the Internet connection was finally back online. But this merely extends the existing network and not what I want. Why this happens? Why my Airport Express can only extend a network, not create one?

Here is the situation on my Airport Express.
If I choose to extend the existing wireless network, the Airport Utility shows like this:
If I set up a wireless network of my own, what I get in the Airport Utility is this:
See my problems here? The Airport Express does not show anything in amble, but the Internet complains that there is no connection.
This problem did not occur before the broadband was renewed and the rounter was replaced.

Would like my macbook pro to only connect to time capsule and not to airport express that is extending network. Is there a way to do this?

I have a network set up with a main time capsule and airport express. The airport express is configured to extend network. While its fine for our iphones and ipad to connect to the express, I would like the Macbook pro to only connect to the time capsule as it seems to run faster. Any way to do this?

You are extending the 2.4ghz.. as that is the only way you can connect iphones.
But if you have Gen2 or later TC you can setup 5ghz to use a different wireless name to 2.4ghz.. and it is much faster.. you need to be close to the TC though.. like in the same room.
Make sure you download 5.6 airport utility if you haven't already.. go to the wireless options and the extra wireless area.. set a different wireless name (SSID in everybody but apple's book). Then you can deliberately select it.

Verizon FIOS, Time Capsule, and Airport Express - How to Extend Network

OK, I just got Verizon FIOS (TV, Internet, and phone). Don't care for the wireless router that is required to be used with it (want 802.11n and Time Capsule). I turned of the wireless on the Verizon FIOS router and installed a Time Capsule in Bridge Mode, which is how the Verizon rep told me to install it. As I understand it, the Verizon FIOS router is still handling DHCP, NAT, etc. I would like to extend the wireless network to reach some dead spots in my house. I have read that the Airport Express can be used to extend a wireless network from an Airport Extreme or Time Capsule, but it appears that I need to set up a WDS with the Time Capsule as the base station, which is apparently not possible on the Time Capsule in Bridge Mode. I am desperately seeking any advice on how to use Verizon FIOS, my Time Capsule, and extend the wireless network to reach the farther corners of the house. I am using a Macbook and a Thinkpad as well as an iPhone on the wireless network with a Dell desktop connected to the Time Capsule via Ethernet. Any help or suggestions would be greatly appreciated. Before I switched, I had Cox Cable with a Buffalo wireless router and it had great range. Now I seem to be in a worse situation from a wireless perspective with higher TV and Internet quality. Thanks in advance.

Welcome to the discussions!
+I would like to extend the wireless network to reach some dead spots in my house. I have read that the Airport Express can be used to extend a wireless network from an Airport Extreme or Time Capsule, but it appears that I need to set up a WDS with the Time Capsule as the base station, which is apparently not possible on the Time Capsule in Bridge Mode+
If you have an AirPort Express(n), you can configure it to "extend a wireless network". This is a more efficient way to add additional wireless coverage (and much easier to configure than a WDS arrangement).
However, if you have an older "b/g" AirPort Express, you must use the WDS configuration method with this device and the Time Capsule if you want to increase your wireless coverage.

Airport Express won't extend network over LAN when plugged into a switch

I have several airport expresses (newest model) and an airport extreme.
Every room in my house is wired for ethernet. Those terminate in a closet and plug into a single switch. That switch then has a single cable that plugs into the airport extreme.
In different areas of the house, I've placed a few expresses to extended the wireless network. After several attempts, the express "hotspots" would only extend the extreme via wifi (offering no real advantage) even though they were plugged into the wall via ethernet.
For grins and giggles, I tried connecting the port directly into the airport extreme (bypassing the switch) and it started to send the traffic over the wired LAN.
Question is - why? I'd much rather everything go through the switch as the extreme has a limited amount of ports and I'd rather use for other things. Anyone had this experience before?
Thanks!

Sorry, the older version of the Express does not have the option to "extend a wireless network", which is the setting on the new Express that provides more wireless coverage and also enables the Ethernet port.
What you want to do can be done with a different setting..."participate in a WDS network" on both the Time Capsule and Express, but I am not recommending that you do this because WDS operates only in "g" wireless mode. Your Time Capsule would lose most of its performance in this setting and the network would slow down tremendously...defintely not what you want for gaming.
You'll have the best performance if you connect the PS3 directly to one of the Ethernet ports on the Time Capsule using an Ethernet cable. If it is not possible to run the cable, the next best performance option would be to use a pair of Ethernet powerline adapters to send the Ethernet signal over the existing AC wiring in your home.

Setup Airport Express as a repeater for Time capsule network?

Can any one provide detailed instructions, or provide a link where I can find these instructions?
Current Setup: TimeWarner Cable Modem/Router (Arris TG852) > Time Capsule router (A1254)
This has created two networks. One from the TW Router and the other from the TC. Even with both networks, I do not have great signal in the last two bedrooms, or bathroom.
I have a Airport Express (A1264)
Can someone explain how to set up the AE as a repeater, and offer any advice on how my network "should be" setup? Thanks
In my reading, I believe this would be Dynamic WDS; correct?

Thanks for the link. It says the below is by far the best way to extend for N networks.
"For 802.11n Wi-Fi base stations, creating a roaming network is by far the best choice. This will provide the best throughput between the base stations and your Wi-Fi devices.
This set up requires that your Wi-Fi base stations are connected via Ethernet.
The primary base station provides DHCP Services, while the extended base station will be configured to use bridge mode.
All Wi-Fi base stations within the roaming network should use the same passwords, security type (Open/WEP/WPA), and network name (SSID)."
But, if my TC and Express are next to each other, how does that fix my wifi problems on the other side of my house?

Use Airport Express as Internet hub, bridge Time Capsule for N-only?

OK I checked on the forums, but I could not find anything quite specific it what I was trying to accomplish.
I recently got a 500GB Time Capsule. I changed my network around, which was based off of two Airport Express stations – on in the office hooked up to internet & printer, one in living room hooked up to sound system – and made the TC the main hub, connecting modem to it's WAN port and bridging the office AX via LAN port in bridged mode, sharing the living room AX as WDS. This way, I had the TC in N-only mode in 5ghz spectrum using wide channels for fastest performance. All this worked well.
Except that I noticed that with the TC in the office – where the laptops rarely are – my data transfer speeds were no better than .11g speeds. So I mucked around a little, and noticed that it really was just the case that the separation of distance & obstruction was slowing the transfer speeds over .11n-only that much!
Well, it occurred to me that there may be another way. What I had intended to do was to hook up the modem back to the office AX, move the TC to the living room where it'd be "line of sight" to the laptops most of the time, and bridge the TC and living room AX over LAN. So the idea was to keep the networks separate wirelessly still, and have the internet "bridged" wirelessly from the office AX to the living room AX and then over LAN to the TC. The thinking was that the hit on the internet connection would not be noticeable as the threshold for that is well below the streaming capabilities of the AX network still, so I'd not lose anything there, but gain MUCH faster speeds with the TC in line-of-sight of the Laptops (3x as much in testing; with TC in office and laptops in living room, 1.3gb folder took 9 minutes, same folder line-of-sight testing took only 3 minutes).
However, I CANNOT get this to work properly. I thought I really just needed to move the TC to the living room and bridge it there, as the services should be shared over the LAN port since the 2.4ghz AX are in "bridged" mode, but that didn't work. I kinda-sorta got it to work by forcing both the AX network AND the TC network into "bridged mode," but that didn't seem right or wise, so I tried some other settings, putting the TC to bridged and having the office AX distribute IP addresses, but then it wouldn't show up under restart, and I'm just confused now on how to set that up!
What i need is: To have the "Office AX" hooked up to the modem & printer, on 2.4ghz since it's the older .11g model, with the "Living Room AX" on that same network. Then the TC in 5ghz N-only bridged to the Living Room AX via LAN, so it can share the services (internet & airtunes) and still get high data transfer speeds to the laptops via the advantage of Line-of-sight, non-obstructed networking.
How do I need to set this up? It's possible, right?
Message was edited by: Anthony Caltabiano

OK while I was working out this morning, I was trying to think of WHY my setup wasn't working. I had an epiphany, and decided to try once more. This time, it worked.
The problem was that originally I had the Living Room AX set up as a Remote, so it was hooking INTO the network, not extending it. I know that with that setup you can't hook up to THAT station and get internet or anything, you hook into the MAIN station and you can SEE the remote's services that are "plugged in" to it.
I didn't think this would be an issue with the TC physically attached to the ethernet port, but apparently this behavior extends to the ethernet port on remote stations for internet access... I had a feeling that MIGHT be it, so I started from scratch, and this time set up the Living Room AX to extend the network instead of just joining it. Then hooking up the TC to the Living Room AX's ethernet port and selecting "Bridge Mode" on the TC got me the good ol' green light!
So, if anyone out there is trying to build a dual-band network, with their TC on .11n-only and bridge to services supplied by a 2.4ghz network, AND route their internet access through the 2.4ghz network instead of the TC so that they can keep their TC more centrally located for better performance... make sure you do it like this: Set up the alternate (2.4ghz) network as relays, "extending" the network, so that when you plug into it, the TC essentially thinks it's plugged directly into the main router, no matter where it is. The throughput hit for internet access over WDS shouldn't be a problem for US-based peeps, as our speeds are typically well below the .11g threshold anyway.
I also found that it helped to NOT hide the SSID of the 2.4ghz network; doing that kept rendering failed attempts to force the secondary AX to join as WDS. Once I redid it without hiding the SSID, all went well.

Airport express won't extend network via ethernet but shows GREEN (HELP!!)

I have the following routers setup up the same network and are working.
10.0.1.1 Airport Extreme (connected to hardline from IP)
10.0.1.2 Time Capsule 1 (extending network and providing internet connection to computer via ethernet)
10.0.1.3 Time Capsule 2 (extending network and providing internet connection to Xbox1)
10.0.1.4 Airport Express 1 (extending network and providing internet connection to Xbox2)
Not working correctly
10.0.1.43 Airport Express 2 (wanting to set this router up to extend network to plug into desktop)
The router seems to join the network fine and will show GREEN but doesn't show a similar IP address as the rest of the routers. It also doesn't provide any internet connection via ethernet to any computer, the network pref page says that it shows RED and that nothing is connected to the computer for internet but airport shows GREEN.
Reset the router multiple times, tried every which way of setting it up and no go. I also tried assigning it a IP and not using DHCP and gave it a 10.0.1.5 and still the same outcome.
Right now just at complete loss as to what to try next.

Sorry, the older version of the Express does not have the option to "extend a wireless network", which is the setting on the new Express that provides more wireless coverage and also enables the Ethernet port.
What you want to do can be done with a different setting..."participate in a WDS network" on both the Time Capsule and Express, but I am not recommending that you do this because WDS operates only in "g" wireless mode. Your Time Capsule would lose most of its performance in this setting and the network would slow down tremendously...defintely not what you want for gaming.
You'll have the best performance if you connect the PS3 directly to one of the Ethernet ports on the Time Capsule using an Ethernet cable. If it is not possible to run the cable, the next best performance option would be to use a pair of Ethernet powerline adapters to send the Ethernet signal over the existing AC wiring in your home.

How do I set up my Airport Express and not interrupt my TIme Capsule

I have ATT UVerse recently installed and have my Time Capsule Router Behind their installed router. I recently purchased Airport Extreme and want to install it as well so I can connect an older Version of a Sony PS3 which doesn't have bluetooth capability via rj45 since the time capsule is no where close to my PS3. Is there a way to install this Airport Express and not mess up the settings of the Time Capsule?

Hello hbwilli. Welcome to the Apple Discussions!
I recently purchased Airport Extreme and want to install it as well so I can connect an older Version of a Sony PS3 which doesn't have bluetooth capability via rj45 since the time capsule is no where close to my PS3. Is there a way to install this Airport Express and not mess up the settings of the Time Capsule?
Yes. You will want to configure the new 802.11n AirPort Express Base Station (AXn) as a ProxySTA. In this configuration, the AXn will join the wireless network created by the Time Capsule and share Internet access through its Ethernet port to the PS3.
To activate ProxySTA, you must set up the Express to join a wireless network and then enable the Allow Ethernet Clients setting; both settings are located in the Wireless tab of AirPort Utility. The feature should work with any wireless network: a, b, g, or n; and 5GHz or 2.4GHz. (Note that the Express, which ships with firmware 7.3, must also be updated to firmware 7.3.1 for this feature to appear.)

Two airport express no longer show w time capsule in utility

did the latest update interfere with our two airport express. i did the Mac update install and neither of the airport express show in the configuration. we also had a power outage yesterday for about 5 hours. not sure which is the culprit but after doing the install and rebooting the entire system we still have no airport express devices showing anymore under the time capsule and their lights are solid yellow.

Factory reset them.. they have stopped boot.. (solid yellow) .. it must flash yellow or when setup correctly go to green.
And yes, Yosemite has the worst airport utility and network on any new OS ever released.. ever.. I mean Vista badness.

Airport Express Won't Extend Network

I have an AirPort Extreme and I am trying to use my AirPort Express to extend its network. For quite a while, it was working fine. Then, due to some interference issues, I had to change the channels on my AirPort Extreme. Since then, the AirPort Express flashes Amber. I have tried restoring it to its default settings from AirPort Utility, as well as the reset button while plugging it in. My computer detects it, renames it, and automatically chooses to extend the network from the Extreme, but when setup is finished, it just flashes Amber. What can I do?

Ii suggest that you run a few quick tests to try to begin to troubleshoot the issue.
Move the AirPort Express to the same room as the AirPort Extreme to reset and reconfigure the device again.
Do you get a green light that way?
If yes, then unplug and move the Express to a location that is no more than half the distance between the AirPort Extreme and the general are that needs more wireless coverage and test to see if the Express will work reliably at that location.
However, if you cannot get the AirPort Express to work when you configure it in the same room as the Airport Extreme.....and you have reset the AirPort Express several times, then it is time to start thinking about the possibilty that the Express is defective.
Please post back on your results, as it still may be necessary to use a good utility like WiFi Explorer to help analzye your wireless network connection quality and take a look at other sources that may be introducing wireless interference that is affecting your network.

Airport Express access over 'Extended' network (Time Capsule)

Similar Messages

Maybe you are looking for