Airport extreme and belkin 54g problems - tried ringing applecare.......

hi all
im new on here and new to the world of mac, i was swayed by the fact thats mac are "relaiable" and i like the OS. anway my airport connection keeps dropping and being really slow then i cant reconnect to it for ages or without having to hard reset my router and put security on again.
i dont think its a problem with the router as my vista laptop connects to it no problem and never drops.
i rang apple and they were not helpful and at one point kept me on hold for 12 minutes in between conversation (on a 0870 number!!) and eventually i had to hang up what they told me was to download a file that they pointed me to and when i did it said i dont have the right hardware for this instillation and realized he told me to download the airpot base station thing
anyway can anyone help me please im getting really frustrated
here are some details from about this mac
Wireless Card Firmware Version: Broadcom BCM43xx 1.0 (4.170.25.8)
thanks for your time
Chris

Thanks.
If you have the Expresses connected via ethernet to the LAN ports on the Extreme,
you will configure each device to "Create a wireless network" with the exact same name, security and password as your Extreme wireless network. You can probably leave the Channel setting at Automatic for now.
In addition, each Express must be configured as a "bridge"
Since the Express is a single band device, you will need to decide whether you want to expand either the 5 GHz network or the 2.4 GHz network from the Extreme's wireless network. The Express can't do both simultaneously.
Post back if you need more info on your "roaming" network setup.
Message was edited by: Bob Timmons

Similar Messages

Airport Extreme and Westell Modem problem

Two days ago I bought a new Airport Extreme to replace my Belkin Wireless G router which operates without problems. I have spent hours unsuccessfully trying to get my AEB to work. My Westell modem is in bridge mode, and each time I configure my AEB to connect via PPoE my results are a flashing amber light on the AEB and a scrolling message next to my airport connection icon which states "Attempting to Negotiate PPoE." After several seconds this message disappears, the airport icon shows full signal strength but I'm unable to connect to the internet. The light is still flashing amber and the Airport Utility indicates that there is a problem with the IP address from the modem.
Reconfiguring the AEB to connect via DHCP results in a green light and the Airport Utility indicates that all is well and I'm connected to the internet. However, each time I try to connect to the internet I'm taken to the configuration page of my Westell Fast Access modem.

I had a similar problem. I had to switch my computer's Airport seting to DHCP from PPPoE. Then I was able to access Airport Utility(be sure to upgrade to 5.1). My Airport Basestation Internet setting was on "Always On". I switched it to "Automatic". Then switch my computer network/Airport setting back to PPPoE. Hope this helps.

Setting up a WDS with airport extreme and Belkin router

Hi,
I had my airport extreme base station set up with a linksys router (the common one everyone has) and it worked fine. I moved and now am trying to set it up with a Belkin F5D7234-4, and have not been able to get it to work. I have tried both the WLAN and the LAN MAC addresses. Is there something I am missing? Thanks

Unfortunately, most non-AirPort routers are not compatible with Apple's implementation of Wireless Distribution System (WDS)...so it very unlikely that your Belkin router can be extended wirelessly with the AirPort Extreme Base Station (AEBS).
The few Belkin routers, that are known to work are models: F5D7230-4 and F5D7231

Create a WDS with Airport Extreme and Belkin Pre-N

I would like to setup a WDS using my Airport Extreme Base as the main router and a Belkin Wireless Pre-N (F5D8230-4) as a remote client. I have done this successfully using Linksys WRT54G and WRT54GS routers (using Sveasoft's firmware upgrade which has WDS), but haven't been able to get a good configuration for the Belkin, nor have I been able to locate a firmware for it.
At this point I'm not concerned about encryption, so leave that variable out. I just can't determine what settings the Belkin router needs to work. I've tried a lot of combinations based on my experience with the Linksys models.
Thanks,
Wes

The Linksys models you reference are some of the few items that will work with Apple's implementation of WDS.
I don't believe that the Belkin device has that ability.

Airport Extreme and Time Capsule problems

I have had an Airport Extreme 802.11g, version 5.7 for several years and have some problems that is get stuck now and then, so I have to restart it. I have tried to upgrade software, but cannot find anything appropriate. Assume 7.5 is a software version, but where and how to upgrade?
I got another problem when I bought a Time Capsule. It interferes with my Siemens Gigaset wireless phone. I have tried to change channel etc, but it does not seem to help. Any tips?
The two problems are not related, as I had the first problem before I got the Time Capsule.
Tor

v5.7 is the latest firmware for your AEB 802.11g.
v7.3.2 is the latest firmware for the TC.
You should probably do these simple maintenance tasks:
Simple Maintenance Tasks:
1. Repair Permissions - /Applications/Utilities/Disk Utility.app. Start Disk Utility, select your HD and click on Repair Permissions. When finished, quit Disk Utility and then restart your computer.
2. Reset PRAM - hold down Option-Command-P-R keys when starting until you hear the startup chime a 2nd time.
3. Safe Mode Startup - hold down the Shift-key at startup until you see the login screen. When logged-in, then go to System Preferences/Network/AirPort
- click on the 'Network Name:' roll-button, select 'Join Other Network...', enter 'Network Name and select the security type you are using, and finally, enter your Password and click 'Join'.
- click on 'Advanced', TCP/IP and confirm that 'Configure IPv4:' is set to 'Using DHCP', click 'OK'.
- click the 'Apply' button and exit System Preferences.
Make sure you separate the AirPort Base Station and the wireless phone by as large a distance as you can.
You could enact Interference Robustness, but it will reduce the range of your AirPort base station:
1. Open AirPort Utility, select the AirPort Base Station (main) and click on 'Manual Setup'.
2. Click on 'Wireless' tab and click 'Wireless Options'.
3. Tick 'Use interference robustness, click 'Done', and click 'Update'.
4. Wait for ABS to restart. Restart your computer and test.

Airport Extreme and USB Printer Problem

I have an Epson printer connected to the USB port of my Airport Extreme. This has worked just fine for years. But from today neither my iMac nor my MacBook Air can "see" the printer any more. I have rebooted everything a couple of times, but still no joy.
I have connected the printer directly to a USB port on my iMac, and all is well, so I guess the problem is not with the printer.
The only thing significant done to my system in recent times is the latest security update, which I installed yesterday.
Can anybody give me a clue as to why this problem has suddenly raised its head after all these years?

Hi bricknell,
It sounds like you are experiencing some printing issues after performing an update to your computer’s software. Here is an article for you with some troubleshooting steps that will help you address this issue:
Troubleshooting printer issues in OS X - Apple Support
https://support.apple.com/en-us/HT203343
Thanks for being a part of the Apple Support Communities!
Regards,
Braden

I'm having a hard time setting up my external hard from with my AirPort Extreme and Time Machine Backups.

I have been using a Mac Mini with an external hard and Time Machine. I bought an Airport Extreme and have had problem setting up the hard drive using the USB port on the Airport Extreme. I also just recently bought a Mac Book Air and hope to have both computers back up to the external hard drive using Time Machine and Airport Extreme. I have been using the optical drive from the Mac mini to load programs into the Mac Book Air. I think I'm just getting confused in Finder. I am just not seeing the hard drive. I ended up plugging the hard drive back into the Mac Mini and that is work fine again. How do I setting the external hard drive up to the AirPort Extreme and use for both computers? Or at least to start with the Mac mini.

It's critical to understand that Time Machine (TM) stores backups differently between local and network drives. That would mean the TM backup on your locally attached USB hard drive will not be directly useable when it is connected to the AirPort Extreme Base Station (AEBS). There is a way to copy a local version to a network version, but it is not fool-proof. When you do connect this drive and point TM to it, TM will start a brand new backup, leaving your existing backup as is.
If your current backup is critical to you, you may want to consider getting a second USB drive to attach to the Extreme and use your existing one as a backup ... or use TM's multi-backup process to backup to more than one destination drive alternatively.
So, at this point, you may want to make a decision on how you want to go forward to help provide a solution for you.
To directly answer your question, when you go to select a destination for a Time Machine backup, the drive(s) that show up under "Backup Disks" are those that TM already recognizes and has backed up to. Those listed under "Available Disks" are drives (either local or on the network) that TM can back up to.

HT4628 Intermittent reception when streaming music via Airport Extreme and Airport Express to powered speakers. Is this a problem with the Extreme?

i get intermittent reception when I stream music from I Tunes via Airport Extreme and Airport Express to powered speakers. I Tunes continues to play uninterupted on the Mac. The problem does not lie with the Express as it occurs on both of my 2 Express at the same time. is this a problem with the Extreme?

Well, repying to my own post... Might have found the solution: I tried to do the same with a Macbook Pro 2010 using the very same setup. And it worked perfectly! No freeze, no nothing.
One explanation I see:
my iMac is dating back to May 2007, a Core 2 Duo 2,16Ghz with 2 Go of RAM.
So the computer's characteristics (or the Wifi component or the combination of all of this) might be not robust enough to allow streaming to those 2 devices...
Anyone's got anything to add?

Airport extreme and HP printer over ethernet problem

I'm new here, so forgive me if this topic has been done to death. I'm running airport extreme and have an HP photosmart 2600 connected to it via ethernet. My wife has no trouble printing with her Macbook Pro (Snow Leopard), but my daughter's older iMac only prints very intermittantly and mostly not at all.I've tried all the sharing options and reinstalling/updating the HP software, but no luck. The printer is at the other end of the house from the Airport, so connecting via usb is not an option. Any assistance much appreciated, thanks.

Using Ethernet should give the best results, plus it allows the use of more than just the print function, which USB would not. Proof of that should be the fact that this older HP model (it works with OS 9!!!) works well with your recent Mac's Snow Leopard OS.
If the iMac has OS X 10.5.8, the correct printer driver should have already been installed and no further update would have been needed. All that should have been needed was to open the Print & Fax panel of System Preferences and add the HP printer as the iMac's default printer.
When the iMac was first unable to print using the HP, did you consider any chance that the iMac was too far from the Extreme, or that there might have been some interference involved? Did you power cycle starting with the modem? When power cycling is necessary, printers seem to throw off unexplainable errors (such as out of paper or ink, paper jam - when none of these is true).

I have a new Airport Extreme and an old airport express. I am getting an amber light on the new Extreme and a green light on the Express. I have internet no problem but the status light is blinking amber

I have a new Airport Extreme and and old airport express. I am getting an amber status light on the Extreme and a green light on the Express. The Extreme is blinking amber all the time.
I have internet and everything seems to be working.
I have reset and pulled the power cord on both the extreme and the internet block
How do I make it Green?

If things seem to be working OK, but the amber light is flashing......the AirPort Extreme has a message for you. To see what that might be......
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click on the AirPort Extreme icon
Click on the amber dot in the small window
It might be a message that a firmware update is available for your AirPort Extreme.

Wireless network issues w Airport Express and Belkins Powerline HD

Hi,
I have a new Airport Extreme and the wireless network generally works great with my iPad and Sony Vaio, but there are wireless deadspots in my house when using my MacBook, and the wifi signal will die out often for it in those spots. I'm guessing it's because my MacBook is old with only a a/b/g wireless capabilities. I tried extending my network using Airport Express in the deadspots, but it did nothing to strengthen the signal (i.e., since it ended up extending the weak signal).
So, I bought a Belkin's Powerline HD (gigabit), connected one Powerline receiver to the Airport Extreme using ethernet and plugged it into the wall outlet. I plugged in the other Powerline receiver into the wall outlet in the separate room with the deadspot, and I connected my the Airport Express to it directly using ethernet and am having no luck getting the Airport Express create/extend my current wifi network (i tried creating a new network too, but no luck). I know the Powerline does work because when I connect my MacBook to it using ethernet (i.e, not using Airport Express), I have no problems connecting to the internet. But I would really like to create/extend a wireless network in the deadspots of the house for my MacBook so I don't have to use the ethernet cable.
In the Airport Utilities, I set up the Airport Express to connect to Airport Extreme using ethernet and extend the current wireless network (also tried creating a new network). I got as far as getting a successful set-up confirmation and a green light on the Express base unit and can get full bars on the MacBook. But when I try to connect to the internet, I get an error message saying that there is no internet connection. (Same error when I created a new wireless network.) The diagnostic says there is no ISP signal/connection, which leads me to believe that the Express is not connecting to the internet through Airport Extreme. What am I missing? Thanks in advance!

HI, I don't know very much about Airport Express or indeed Apple products in general. However, I do use Belkin 200mbps powerline adapters.
I have used these adapters in two separate ways. 1) device to router; 2) additional wireless access point to router
In the first situation they work perfectly fine and the connection is fast and reliable for anything I care to throw at it (file transfers, audio / video streaming, internet browsing). However, in the second situation the connection drops intermittently. I will have access to the main router via the access point over powerline for all devices, then suddenly this will just stop. To restart it I have to remove the powerline from the mains, wait about ten seconds, plug back in, let it boot up and reconnect and I'm connected again.
Having read more (sorry I don't have the links to hand), it appears that powerline adapters can handle one-to-one traffic fine, but when bridging a wireless access point where several wireless clients are transmitting / receiving, they 'lock up' and just stop. Even when connected in this configuration, streams tend to stutter and my squeezebox devices get totally out of synch.
Given I know very little about Airport Express (i conceded as much at the top of this post), is it fair to assume that a belkin powerline connected to the 'Express' would closer match with scenario 2 in my above description? If so, I'm afraid I don't believe Belkin Powerline will be a suitable solution for you. Hope my experience saves you the days of head-scratching I went through before removing powerline devices (incidentally, I bought a wireless repeater to solve my problem in the end, and put the powerline adapters to good use by connecting my media player (under the TV) to the main router directly).

Airport Extreme and external HDD - cannot be found under Windows (XP/Vista)

Dear All,
I am about to loose it. I have an Airport Extreme (7.4.2), most recent version (802.11n)connected to my cable modem. Attached is a 2TB HFS+ Formated HDD. I have a number of machines. My primary machine is a Dell XPS with Vista and MacDrive installed.
Now: On my AirPort utilities through the Dell the different HDD's connected via USB (I have tried half a dozen) are all visible. They are shared and I have tried all options, e.g. "with Disk Password" etc, tried to give and deny access to guests etc.
I have tried various things incl. switching off the firewall has not been a success either. I am basically ready to buy a Mac now, but I am worried that the problem will persist for all my Windows based PC's.
Who can help with a step to step guide? tried the TCP/IP settings on the XP machine as well (entering the IP address of both Airport Extreme and Express).

Hi!
I've got the same problem as of Friday when I upgraded my Notebook from XP to Windows 7.
It does not recognize the HDD anymore, neither on the Windows7 Notebook nor on 2 different XP- PC's.
I disabled the password functionality and removed the HDD several times, no change.
When I look to the data volumes overview in the system settings, all internal HDD's and the CD partition of the Toshiba drive are shown. The HDD partition of the drive is shown as "non allocated".
Is there any workaround to get access to the data????
Best regards,
Helmut

New Airport Extreme and iPhone Issues

I've had the networking day from ****. I previously had a 3rd Gen Time Capsule at our restaurant, connected to a Cisco 26port gigabit POE switch and Comcast digital voice and internet. Over the past few days, employees have reported trouble accessing the the Wifi network. After several restarts and firmware upgrades (including the dreaded "firmware problem" to fine update), nothing worked. I changed channels, back to auto, back to specific channels, back to auto. Made open guest networks. Nothing worked consistently. My iPhone might connect and my friend's might not. Nor his laptop consistently. Our Axis network cameras might take a bit extra time to connect. All quite random and quite frustrating.
So I swap out an older Airport Extreme (4th gen I believe) using the same configuration as the TC (Time Capsule). It works fine, except for the last port not working as expected. No matter, I plug the mac mini into the Cisco switch and off we go. Nevertheless, I'm still told we are suffering random Wifi issues. So I buy a brand new AE (5th gen) today to replace that one. Should work like a charm I thought. Right....
Several hours later, I finally have the new AE working, but only after doing several hard resets/factory restores, the works. For some reason, the mac mini could not successfully update any of the connected AEs - whether connected directly into the same AE, or if the Mini was connected to the switch. Nothing worked. Every time I tried to update the AE, it would hang and force me to unplug and plug it back in. It would also never save setting changes. I finally resorted to a friend's macbook to be able to restore it successfully. And once that worked, the mini was able to update the AE flawlessly. Our Point of Sales (POS) machines connect fine, our cameras connect fine, wifi printer connects, and the mini connects, and everything has internet.
Except my iPhone 5. Of course. It gets a signal fine (full bars). It gets an IP address. But I can't surf the web. Or download email. Or iMessages. Anything. No internet access. I try hard restarts on my iphone. I try assigning IP addresses by MAC address. I try resetting the AE. I try renaming the WiFi name. Nothing. I can make a guest network that works (on a different IP table, btw - 172, not 192.) But other than that, no access. Grrrr.
So I have a "working" AE router where some devices successfully connect (through wifi and ethernet) and some dont' (wifi iPhone). My iPhone connects fine to my home TC. So shouldn't be anything to do with that. But I'm at a loss. I'm going to go back and restore everything and power cycle everything tonight or tomorrow night. I don't know if that will help, but it's worth a try. Lord knows it feels like I've tried everything else.
Anyone have any good ideas of where to start besides voodoo dolls and baseball bats?

I took mine back, because I was having these very same issues. We use contivity too. I was able to connect only to one of three of the servers we manage (in Europe). I couldn't connect to the servers in Asia or here in the USA.
Replaced the Airport Extreme with my trusty old d-link 624, and no issues connecting to any of the three hubs.
Otherwise, I liked the Airport Extreme, and I'll consider buying it again when and if they address this VPN issue. I work at home so its obviously a "deal breaker" for me.

How do I connect Airport Extreme and Time Capsule to my new iMac so that AE is used for network and TC only used for Time Machine backup?

I didn't realize that Time Capsule will only support the print function of a wireless multifunction printer. So I want to use Extreme for my network to have full use of my printer and use TC as the Time machine backup only. How to I make the connections?

Thanks for your response and this is getting complicated but I just purchased a new iMac as well as the Airport TC. I've had the Airport Extreme for a year or so. The Airport Extreme worked perfectly with my old iMac wirelessly and I had all functions of my printer with no problems. I was expecting the same with the TC. But the instruction that came with TC say to connect the printer to the TC via USB...which I did. And the print function worked perfectly but nothing else. In researching I discovered that when wired that way the TC only supports the print function...not scan or fax or anything else. I tried going wireless since my AE worked perfectly via wireless but I got no printer functions at all that way. But I'm wondering also if I tried that during a time I was having other issues...I had to delete and re-add my printer which solved some other problems. I may try that again...and see if I can get all print functions with just the TC connected
As far as connecting both your AirPort Extreme and Time Capsule on your network, we're not clear on exactly how you want to do this. Will the AirPort Extreme connect to your modem using an Ethernet cable and the Time Capsule connect to the AirPort Extreme using an Ethernet cable?.......or......do you want the Time Capsule to connect to the network using wireless?
Well... first of all I would like not to have to use the AE at all...I would prefer using just my TC for network, all print functions and Time Machine backup if that's possible. My printer will not accept Ethernet connections (Canon MX512).
After failing at getting this to work, I decided I would try to use my AE for net and print functions and just use my TC for Time Machine backup. I tried several different connection configurations with no success until finally I connected cable modem to my AE via Ethernet and went wireless with the AE and printer. but connected the AE to the TC via Ethernet and amazingly everything worked like a charm (for a while) and I was patting myself on the back for being so smart. But now I find that the connection only lasts for a short time. If I leave it for a while the TC goes invisible...or at least I see a message saying the Ethernet is unplugged...but it is not... and I lose internet connection even though I have a green light on my AE. So now I'm at a loss. I don't know why I keep losing network signal and why my system thinks the Ethernet is unplugged.
So... after all this...I figured I wasn't so smart after all and I must have things wired incorrectly.
So... it sounds like you are saying I should go back and try again to get my new TC to work as I want it to via wireless instead of connecting via USB...is that correct? Could you tell me exactly how I should wire my equipment from cable modem to AE and/or TC to achieve net capability, full functions of my printer and Time Machine backup...
Thanks...

How to setup a network with a time capsule, airport extreme and an airport express?

Hello.
First I want to make it clear all my knowledge off wireless networks is going on forums on the internet, before a couple of months ago I didn't realize wireless networking was so intricate so forgive my lack of experience.
I just bought a time capsule (today, 4th generation), I have an airport extreme bought in January 2011 (they just got refreshed so mine is now one generation old) and the same with my airport express (bought in January).
I originally bought the airport extreme and setup a wireless network using the dual band setup. I have no issues with the 5ghz network and most of my devices run on wireless n so I had no issues with them. my only two wireless devices that can not use the 5ghz network is my iPhone 4's which use wireless n but it has to use the 2.4ghz signal. Problem is in my apartment I am bombarded with other peoples 2.4ghz networks so my signal is terrible 10-15 feet from the airport extreme. Near my extreme I am getting signal ranges around 15mb to 20 mb. When Im about 15 minutes away in my bedroom (so one wall in between) my signal plummets to 1-2 mb. sometimes as low as 0.17mb which is not good. I got the airport express to extend my range and placed it in my bedroom. . After setting up the airport express the signal still was terrible. I researched and realized that if the signal strength ***** then the airport express cant boost the signal as much which makes sense in hind sight. I then researched setting up a roaming network or a WDS network. Per research a WDS network was not recommended b/c I was not using a wireless g network. I attempted to create a roaming network and then realized that you can not use an airport express in a roaming network. This has led me to now buy a time capsule.
First, in my setup do I or should I have the time capsule as the primary? I believe its more powerful than the airport extreme but Im not sure if that matters in a network that is distributing wifi from ethernet (thats how I am connected the extreme and the time capsule)
so can I do
cable modem ETHERNET Airport extreme(in the living room where its always been and works great in that immediate area) (3rd generation) ETHERNET Time Capsule(in the bedroom where I usually get poor signal) (4th gen) and then an airport express connecting to the 2.4ghz signal in the bedroom where the time capsule also is EXTENDING the wireless range?
or should it be the time capsule first bc its more powerful?
I tried setting up this setup and everything is green but I don't know if what I am doing is actually working on full cylinders b/c I am confused on some aspects. mainly on the airport extreme which is the primary device I have under the wireless tab selected create a wireless network and on the time capsule it also is on create a wireless network with the network name being exactly the same. Should it be changed to extend a wireless network? and then bridge mode? Should I have different channels for the different devices that are on 2.4ghz?
I am open to hear ANY suggestions, or ideas to improve my setup. PLEASE PLEASE HELP!!!!!!!, lol its been 5 long months of poor internet in my bedroom where my wife has her setup with a roku box and wifi tv (I have those hardwired for now) but mainly for her iPad and iPhone b/c its so bad sometimes she has to turn wifi off and use 3G. I have same issue in my bathroom, sometimes Im getting decent signal and sometimes its so bad I can't open the link on an RSS feed in safari which I have to assume doesn't require that much bandwith?
I have no wireless g devices. The only device I need 2.4ghz for is my iPhone 4's but they both use n also. All my other deivices connect on 5ghz and my 5ghz network is decent, a lot better than the 2.4ghz network atleast.

You wrote so much that I find it hard to address all your concerns. However, here are some thoughts:
1) I'd configure the Time Capsule as the "main" router, connected directly to your cable modem. Configure it to "create a wireless network" and to "Allow this network to be extended". Configure the other devices to "Extend a wireless network".
2) Put any device that's extending the network half way between the main router and the wireless clients. If the signal from the main router is weak at the cllient's location, then the extending device will also receive a weak signal.

Airport extreme and belkin 54g problems - tried ringing applecare.......

Similar Messages

Maybe you are looking for