Airport extreme,express and time capsule

I need expand my wireless network. I have three floor . In the middle i have a time capsule with adsl. At the first floor i have airport extreme that expand signal of my wifi. In the last floor i have an aiport express but i don't  Be able to configure this with third repeater.... Can i do this? Can you help me? Thank

If your AirPort Express is a 802.11n model, then configuring it to extend the TC's wireless network would be the same as you did when you configured the AirPort Extreme to do so. Please check out the following Apple Support article to make sure you didn't miss anything when you attempted to configure yours.

Similar Messages

  • HT4259 This article is outdated (as well as others). I have Airport Extreme (latest) and Time Capsule (earlier version) and newest Airport Utility version.

    I have difficulty in setting up the newest Airport Extreme with Time Capsule. How to wire Time Capsule over ethernet is so confusing and the documentation I found is outdated.

    OK, thanks for the clarification.
    Disconnect the Ethernet cable if it is plugged into the Time Capsule at this time.
    With the Time Capsule powered on, hold in the reset button on the back of the device for 9-10 seconds and then release. Allow a full minute for the Time Capsule to restart to a slow, blinking amber light.
    This will not affect any backups that you might have already stored on the Time Capsule.
    Connect the Ethernet cable to the WAN "O" port on the Time Capsule. I assume that you have tested the Ethernet cable independently to make sure that it is working correctly.
    Click the AirPort icon at the top of the Mac's screen and wait a few seconds for a listing of New AirPort Base Station to appear. Just below that, click directly on Time Capsule.  The screenshot below shows an AirPort Express.....you will see Time Capsule on your screen.
    AirPort Setup will open up automatically and take a minute to analyze the network, then announce that the Time Capsule will be configured to extend the AirPort Extreme network.
    Enter a device name that you want to use for the Time Capsule. You can use the same name that you used before, then click Next.
    Now AirPort Setup will indicate that the Time Capsule is being configured to extend using Ethernet. When you see the message of Setup Complete, click Done.  That's it.

  • Airport Express and Time Capsule connection issues

    I have the following setup:
    - Airport Express set up as 'create a wifi network' with the exact same name and password as my main network from my BT router
    - Time Capsule setup to 'join existing network' which is the same name - obvioulsy! - as the other two.
    Everything worked OK until fairly recently. My MBP which usually is connected to the AE n/w accessed the TC via Time Machine OK, and my iMac backed up via TM to the TC OK as well.  Now, however, the TC (which is situated in range of both the AE and the main router) seems to connect sometimes to the (weaker) AE and sometimes to the (almost adjacent) main router.
    If it connects to the main router network, my iMac backups are OK, but if it connects to the AE network, then TM just fails with the usual 'backup disk cannot be found' even though it is clearly visible in Finder.
    Is there anyway of locking the TC into a particular network?

    OK, thanks for the information.
    Temporarily, disconnect the Ethernet cable from the AirPort Extreme to the Time Capsule's WAN port.
    Close AirPort Utility 6.1 on the Mac if it is open
    Start over by holding in the reset button on the back of the Time Capsule for 9-10 seconds, then allow 60 seconds for it to restart to a slow, blinking amber light
    Connect the Ethernet cable from the AirPort Extreme to the WAN port on the Time Capsule
    Click the AirPort icon at the top of the Mac's screen and wait a minute for the heading of New Apple Base Station to appear. Under that,  click on the Time Capsule.
    AirPort Utility will open automatically and take a minute to analyze the connection. After a minute, it will display a message that the network will be configured to "Extend".
    Enter a name for the Time Capsule and click Next
    AirPort Utility will take another minute to configure everything.  When you see the message of Setup Complete, click Done.
    You should now be able to connect to the Time Capsule wireless signal.

  • Best way to extend wireless via airport express and time capsule

    best way to extend wireless via airport express and time capsule
    i live in a two storey house where i use my airport express to create a wireless network in the main floor, and time capsule to extend it in the upper floor, where my room is. i have like 16 mbps in the main floor, and 2-3 mbps in the upper floor after having speediest.
    i used time capsule in the upper floor because i use wireless backup daily and don't want to put internet down while i im doin it and consequently my parent can have internet access in the main floor, am i right? or do i have make just the opposite in order to have a good internet speed?
    secondly, while checking airport express wireless mode on airport utility, there is like 4 different type of radio mode(802 11n bg comp, 802 11n 2.4, 802 11n a comp, 802 11n 5ghz) which i have no idea what they mean
    what do you recommend?
    we have like iphone4, iphone 3g, mbookpro, ipad, ipad 2, samsung tv and a sony vaio laptop in the wireless network
    thank you

    What you have would appear to be working but I can comment how I would redefine your setup.  Note that both Airport Express and Time Capsule can function as wireless base stations so you do have wireless everywhere and at all times — using the Time Capsules for backups doesn’t mean your parents won’t have internet access regardless of the where the base stations are located.
    You appear to have devices to connect to your network that use the 2.4 GHz band with 802.11g such as the iPhone 3G and perhaps the 5 GHz band with 802.11n such as likely the Macbook Pro if it’s a recent model.  The iPhone 4 can use 5 GHz and 802.11n.  Can’t comment on the Sony and Samsung but you can check their specs.
    Now the Time Capsule (if it’s a recent version), can simultaneously supply 2.4 GHz and 5 GHz band signals, but the Airport Express (if it’s recent) can only use one of those bands at one time.  Likely the lowest common denominator for your devices is going to be the 2.4 GHz band since the devices that are capable of using 5 GHZ also support 2.4 GHz.  If you don’t use 5 GHz, you won’t lose much in a two-storey home because likely it’s the 2.4 GHz band is better signal anyway because 5 GHz signals drop off quickly with several walls/floors to penetrate.
    You also didn’t mention if the Airport Express is used to support a printer and/or AirPlay (using iTunes to play on remote speakers via the Airport Express connection) but that might also be a factor in the best location to place the Airport Express.  Although the printer could be switched between the Time Capsule and the Airport Express if needed, only the Airport Express will support your remote speakers.
    Recommend you use the Time Capsule as the Base station.  When using Airport Utility to define the network, after you name your network, etc., select the Wireless tab, check the box “Allow this network to be extended” and set the Radio Mode to "802.11n (802.11b/g compatible)”.
    Using the Airport Utility, click on the Airport Express; after you define the device and network name, select the Wireless tab, define the Wireless Mode as “Extend a Wireless Network” and check the box “Allow wireless clients”. 
    Hope that helps.

  • Conflicts with Airport Express and Time Capsule

    I am using Airport Express and Time Capsule at the same time. Connection to the web is via a router. Very often I do have conflicts. How shall I connect the gadgets? At the moment I connect the router to Airport Express (network cable).
    Time machine back up doesn't work properly.
    Is there anybody able to help me?
    Regards

    What broadband type do you have?
    It can be impossible to plug a TC into the existing connection because the virgin media router has special setup or logins which are not revealed to end users.
    If it is a fibre connection for instance the TC may simply not work. They have issues with many fibre ISP putting the gateway address outside the subnet of the main public IP.. (don't worry if it is too technical .. it amounts to .. it don't work! )
    You may need to wait until Sat.
    Get in a big supply of home videos or something and try and starve off your addiction.

  • Internet - AirPort Extreme (b/g) - Time Capsule - File Server

    I've got a small office network where files are served off a Mac mini, and iMacs connected via 802.11n wifi to the wired mini via Time Capsule. I have a spare AEBS (b/g) that I was thinking of setting it up for iPhone and guest access of internet. To keep the mini and iMacs secure, the set-up would be:
    Internet -> AirPort Extreme (b/g) -> Time Capsule -> Mac mini and iMacs
    The only issue I'm contemplating - the slower Ethernet ports on the Extreme - which I don't think is a problem for connecting to the Internet. Is there anything else I should be concerned about regarding network performance?
    Thanks in advance for the collective wisdom!
    Message was edited by: openarchitecture

    That would work. The Ethernet ports on the AirPort Extreme base station (AEBS) is faster than your internet connection so you shouldn't have a problem.

  • AirPort Extreme with 3T time capsule file security question

    Right now I am using a MacMini with an external HD as a file server.  I'm thinking g of using the new AirPort Extreme with 3T time capsule to do the same tho g (while also extended my wifi reach).
    With the Mac mini I have fine control over who gets to see and do what to which folders and files.  It seems that with the AirPort Extreme thee is no notion of permissions or access control -- if you can get on the wireless you can access the files.  That is extremely insecure. 
    Is my understanding correct?  Is there no way to secure files hosted on an AirPort Extreme so only certain users can access them??
    - john

    Are there any instructions for how to format and set HFS+ user permissions on the AP Extreme's HDD?
    For the formatting part, you will need to temporarily connect the drive to your Mac, and then, use the Disk Utility (a part of the OS X operating system) to partition and format the drive. You should find this utility in the \Applications\Utilities folder. For HFS+, choose "Mac OS Extended (Journaled)" for the Format option.
    For assigning user permissions using accounts, you will need to use the AirPort Utility.
    Run the AirPort Utility
    Select the Extreme, and then, click on Edit.
    Select the Disks tab.
    Select the HDD in the Partitions window.
    Choose "With accounts" as the Secure Shared Disks option.
    Click on the "+" button to add user accounts.
    For each account desired, enter the Account Name, Password, and File Sharing Access type.
    Click Save.
    Click Update to write the new configuration information to the base station and wait for the station to restart.

  • What is the best way to hookup my airport extreme with my time capsule ?

    what is the best way to hookup my airport extreme with my time capsule ?

    It sounds like you have the AirPort Extreme configured as the "main" router on your network.
    If that is the case, connect an Ethernet cable from one of the LAN <-> ports on the AirPort Extreme to the WAN "O" port on the Time Capsule
    Power up the Time Capsule
    Connect another spare Ethernet cable from your Mac to one of the LAN <-> ports on the Time Capsule
    Open Macintosh HD > Applications  > Utilities > AirPort Utility
    Click on the Time Capsule, then click Manual Setup
    Click the Wireless tab below the row of icons and make sure that the setting for Wireless Mode = Off
    Click the Internet icon, the click the Internet tab
    Insure that the setting for Connect Using = Ethernet
    Insure that the setting for Connection Sharing = Off (Bridge Mode)
    Click the Update button at the lower right of the window and wait a full minute for the Time Capsule to restart
    Then power cycle the entire network by powering everything off....order of power down does not matter
    Wait a minute
    Power up the modem first, and let it run a few minutes by itself
    Power up the AirPort Extreme next and let it run a full minute
    Power up the Time Capsule next and let it run a full minute
    Keep starting devices one at a time about a minute apart until the entire network is back up
    You will need to reset the backup path from your Mac to the Time Capsule to get backups going again
    Open System Preference (gear icon on the dock)
    Open Time Machine
    Click Select Disk
    Click the Time Capsule to highlight it
    Click Use for Backups or Use Disk and backups should begin again in a few minutes
    If you do not want to leave the Mac connected to the Time Capsule by Ethernet, remove the Ethernet cable from the Mac to the Time Capsule, then log on to the AirPort Extreme wireless network

  • How to extend wireless with airport express and time capsule

    So, I have a time capsule & because of the thick walls in my apartment, I can barely use my ipad and iphone at night in my bedroom! (my macbookPRO stays at 3 bars however!)
    I bought an airport express thinking I could plug it closer to or inside my bedroom to boost the signal - but it doesn't seem to work that way - any tips on how to set this up?
    TWO ADDITIONAL Qs:
    Does connecting directly to my time capsule (which i'm assuming i'd need another ethernet cable) help with the boost? (then negates the other great uses for the airport express it seems)
    Isn't there a way to do the boost with the express wirelessly? I'd really love to get wireless speakers, use airplay AND be able to use my devices just two rooms away ....   HELP!
    thanks so much (when did apple phone support start to be closed on Sundays?)
    cheers.

    Suggest that you check your setup again to make sure that the settings are correct on both the Time Capsule and AirPort Express.
    Open AirPort Utility, select the Time Capsule and click Manual Setup
    Click the Wireless tab below the row of icons
    Make sure that a check mark is entered next to "Allow this network to be extended".( If the box is not checked, the Time Capsule will not extend to the AirPort Express)
    Click Update to save your settings and close AirPort Utility
    Next, open AirPort Utility again, select the AirPort Express and click Manual Setup
    Click the Wireless tab
    Settings should look like this:
    Wireless Mode = Extend a wireless network
    Wireless Network Name = Same name as the Time Capsule network
    Check mark entered next to "Allow wireless clients"
    Wireless Security = Same setting as the Time Capsule
    Wireless Password = Same password as the Time Capsule network
    Confirm Password
    Update to save settings and close AirPort Utility
    Locate the AirPort Express approximately half way between the Time Capsule and area that needs more wireless coverage. You may need to experiment on placement to find the best compomise.
    Post back on your results.

  • Extending wifi with airport express and time capsule

    Hi All
    I'm new to macs and moving over in a big way!
    I started with a time capsule and all was fine apart from the coverage in the house.
    It seemed easy to extend the wifi so purchased an AE 802.11n and extended the network.
    It does extend and I can connect to the internet but the network is now really really slow and the time capsule backup wont work.
    connection is :
    Ethernet modem - Airport express ( as its close to my audio equipment ) - extended WIFI conection via 802.11n.
    Any suggestions? why is it so slow?
    Im at 7.3.1 firmware on both AE and time capsule and the Macbook pro is at 10.5.3.
    Any suggestions?

    I've managed to change the 5gHz of ther Airport Express that's extending the network.
    As mentioned, main AE is on channel 48, and I now have the 2nd AE on channel 36 - which means my TV can now see the network. Also tested speed via my mavbook air on the same 5gHz network as it all seems OK (A while ago I spotted my Time Capsule was on the same channel 48 as main AE and throughput was abysmal! Bad enough to make me reset the TC to factory defaults and setup again - which is when the TC got channel 120).
    Anyway, the fix... I changed the 2nd AE to create a wireless network (instead of extend), and manually set the channel to 36. I then set it back to extend, and it seems to have kept channel 36.

  • Airport express and time capsule config?

    I have an airport express for Wi-Fi internet and printing. I have purchased a time capsule as a back -up drive to work with time machine. Should I
    set it up seperately from the airport express or
    replace airport express with time capsule ?
    What's the best config and can I retqin existing netwrok ID and password?
    Thanks for pointing me in right direction.

    Hi Yoreilly:
    i'm not sure just what setup is right for you.  and i'm sure the newer Airport Express is way improved over mine (got mine few yrs ago).  but my Airport express works as extension from your Time Cap Wi-Fi.  Airport does not put out wireless Wi-Fi signal on it's own. 
    1>  if yours can take your phone line & send out Wi-fi signal on it's own, then more power to you/ & you could sell back your Time Cap & just have a WD backup drive, or seagate external drive for less. 
    2>  otherwise, your airport express needs to connect to your Time Cap, to answer you #2. 
    3>  usually the application helps where you have dead spots in your house, or your location of Time Cap can't reach places in your house where U need Wi-Fi signal, or where you can't thread an ethernet cable out to your printer or device.
    not sure how you are setup with your wireless printer now.  but if your setup allows you to print by only using the Airport Exp, sure you can use the TimeCap separately as it's own Back-up drive.  the thing is it has Wi-fi capability that you wouldn't be using with that setup.
    hope this helps, & didn't confuse,
    m

  • Printing completely broken on both airport express and time capsule

    Printing seems to be broken on both my old time capsul, generation one, and a new airport express.  Here's what happens.
    1.  Connect printer directly to the Mac and everything prints fine.
    2.  Reconnect printer to the Airport or timecapsule.  Delete all the printers.  Power cycle everything.  Add printer.  Print and it keeps trying to connect to the printer forever.
    It use to work and it may have been a recient firmware update that broke it.  Any help would be appreciated.  I've been through all of the support documents and still nothing.  The printer is an old Epson Stylus R280.  I'm running 10.9 with all the latest drivers and updates.

    If you want to run a N speeds, run a cable from Time Capsule to Airport Express, set Time Capsule as your primary router, and turn off DHCP on Airport Express. This will create two networks, your Express will have one SSID, and the Time Capsule another SSID. One G network and one N network. Don't include the express in your network, keep it separate from Time Capsule to avoid it from coming down to G speeds. Make sense?

  • Use airport extreme to extend time capsule network

    I have tc and an airport extreme. I want to use the airport extreme to extend my network and because I can use it to connect my directv receiver directly by ethernet. How do I set up the second router to act as an extension?

    Won't using WDS (which is harder to set up) prevent use of 802.11n mode? It's my understanding that WDS is limited to 802.11b/g modes. This would be obviated by simply using the AEBS to extend the existing network and configuring the TC to be extended, correct?
    I don't know. I have 1 802.11n Airport Extreme and a Snow 802.11b/g Airport Extreme and an 802.11b/g Airport Express.
    I have only experimented with WDS between the Snow and Express so I can not speak about 802.11n.
    However, if the Time Capsule and Airport Extreme are still supporting 802.11b/g then they must operate in the 2.4GHz frequence range. This will limit 802.11n performance. This is why I use my 802.11n Airport Extreme in 5GHz ONLY mode servicing just the 802.11n devices, and I use the older Snow and Express in Bridge mode to support my 802.11b/g devices using the 2.4GHz frequences.
    The only way I know to properly extend an 802.11n network is to create a *Roaming WiFi Network*. This involves running an ethernet cable from the Time Capsule to the Airport Extreme. Then configure the Airport Extreme and Time Capsule so they have identical SSID, WiFi encryption method, and password. In addition, the Airport Extreme -> Internet -> Internet Connection tab must have "Connection Sharing:" set to "Off (Bridge Mode)" so that the Time Capsule provides all the routing services and there is only 1 subnet in the home.
    Of course I'm willing to learn new tricks, so if there is a way to wirelessly extend the 802.11n network and stay in the 5GHz frequences, I am interested, as you never know, some day I will most likely own another 802.11n base station.

  • Connecting Airport Extreme N to Time Capsule via ethernet to extend wireles

    Hi, I currently have 2 Airport Extreme N and a Time capsule and would like to connect all three together. I am planning to use the time Capsule as the router and then use the other airport extreme to extend the wireless network. I am planning to have ethernet connection between the three devices ie Airport extreme N (A) is connected to time capsule via ethernet and airport extreme N (B) is connected to time capsule via another ethernet.
    I have tried the Extend Wireless network option to connect them, but that seems to generate so much traffic between the airport extreme N and the time capsule that the network is not usable. I have also tried using WDS but that didn't seem to work.
    The three wireless networks have some areas of overlap but the signal is weak which is why i prefer to link them up with ethernet.
    What is the best wall to configure them? should I set them up so that they're each creating a wireless network but with the same name? Or is there a better solution? Thanks!

    It seems to me the easiest way is to have the Airport Extreme connect to internet using Ethernet, using DHCP and the Connection sharing in off (bridge mode) and then create a new wireless network with the same name... Is that correct? I have previously ran the apple wizard and it did something weird with the network and then both the time capsule and the airport extreme are serving out IP address and both of them have the same IP address 10.0.1.1. which then messes up everything...
    Any ideas? thanks!

  • How do I add an airport extreme to existing time capsule network and be able to use the router ethernet ports?

    Good day everyone.  I recently upgraded my airport extreme network by replacing the base station with a time capsule router.  Since I now have an "extra" airport extreme router, I've set it up on the other side of the house to both extend the wireless range as well as use it's LAN ports for a home theater system in that location.  Connecting the two routers was done via ethernet.  It now appears that I need to do something "else" as the LAN ports on the now relocated airport extreme are nonfunctional.  All devices are operating well for wireless and as a review, the modem is connected to the time capsule WAN which is connected to the airport extreme via ethernet cable via LAN to it's WAN port.  What do I need to change on configurations to get the LAN ports functioning on the airport extreme?  Thank you for any help.

    Connecting the two routers was done via ethernet.  It now appears that I need to do something "else" as the LAN ports on the now relocated airport extreme are nonfunctional.
    With both base stations interconnected by Ethernet you have the basis for a "roaming" type network. If properly configured, both base stations' Ethernet ports would be enabled for wired clients.
    The key configuration items for a roaming network are as follows:
    All base stations used must be interconnected by Ethernet.
    The "main" base station; the one connected to the Internet modem, must be configured to provide both NAT & DHCP services; all other base stations used must be configured as bridges (NAT & DHCP disabled.)
    Each base station must have a unique base station name.
    Each base station must use the same wireless security type and password.

Maybe you are looking for