AP 1252 dot11radio interface status shows RESET

Hi,
This is regarding an issue with one of my access point. The access point 1252 is autonomous one running the IOS version
C1250 Software (C1250-K9W7-M), Version 12.4(10b)JDA3, RELEASE SOFTWARE (fc1)
The status of the dot11Radio 0 interface is showing as RESET. I have pasted the interface brief details below.
ap03#
ap03#
ap03#sh ip int brief
Interface                  IP-Address      OK? Method Status                Protocol
BVI1                       <ipaddress>       YES DHCP   up                    up 
Dot11Radio0                unassigned      YES TFTP   reset                 down
Dot11Radio0.102            unassigned      YES unset  reset                 down
Dot11Radio0.104            unassigned      YES unset  reset                 down
Dot11Radio0.105            unassigned      YES unset  reset                 down
Dot11Radio0.108            unassigned      YES unset  reset                 down
Dot11Radio1                unassigned      YES TFTP   administratively down down
GigabitEthernet0           unassigned      YES TFTP   up                    up 
GigabitEthernet0.102       unassigned      YES unset  up                    up 
GigabitEthernet0.104       unassigned      YES unset  up                    up 
GigabitEthernet0.105       unassigned      YES unset  up                    up 
GigabitEthernet0.106       unassigned      YES unset  up                    up 
GigabitEthernet0.108       unassigned      YES unset  up                    up 
ap03#
Due to this the clientsa re not getting associated.
I tried rebooting the AP; shut the dot11radio0 interface and unshut it; verified the switch end duplex speed settings. Looks good.
Can anyone suggest me how to proceed?
Thankyou.

Hi,
Yes the Access Point was working fine all these days and for the last one week, I am facing this problem. Please find the  running configuration of the Access point as below..
Building configuration...
Current configuration : 8275 bytes
version 12.4
no service pad
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
hostname ap03
logging buffered 65536 notifications
enable secret 5 $1$.WG7$dvJpY1XHuixBk3wA4sfR3/
aaa new-model
aaa group server radius rad_eap
server auth-port 1812 acct-port 1813
aaa authentication login default group tacacs+ local enable
aaa authentication login eap_methods group rad_eap
aaa authorization exec default group tacacs+ local
aaa accounting exec default start-stop group tacacs+
aaa session-id common
clock timezone MST -7
clock summer-time MDT recurring
ip rcmd rsh-enable
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host ncc ncc
ip rcmd remote-host ncc ncc
ip rcmd remote-host ncc ncc
ip rcmd remote-host ncc ncc
ip rcmd remote-host ncc ncc
ip rcmd remote-host ncc ncc
ip rcmd remote-host ncc ncc
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host netsvcs netsvcs enable
ip rcmd remote-host netsvcs netsvcs enable
ip rcmd remote-host netsvcs netsvcs enable
ip rcmd remote-host netsvcs netsvcs enable
ip rcmd remote-host netsvcs netsvcs enable
ip rcmd remote-host netsvcs netsvcs enable
ip rcmd remote-host netsvcs netsvcs enable
ip rcmd remote-host netsvcs netsvcs enable
ip rcmd remote-host netsvcs netsvcs enable
ip rcmd remote-host datacom datacom enable
ip domain list u04129.albertsons.com
ip domain list albertsons.com
ip domain name u04129.albertsons.com
ip name-server
ip ssh time-out 90
dot11 activity-timeout unknown default 28800
dot11 ssid Courage-34idkeysNCswuZue3765#%@&
   vlan 102
   authentication open eap eap_methods
   authentication key-management wpa
dot11 ssid Freedom-jKb%&552en@546AsdfG65eD
   vlan 105
   authentication open eap eap_methods
   authentication network-eap eap_methods
   authentication key-management wpa
dot11 ssid Galaxy-73j4CA58fd66y3lKICK#%@&*
   vlan 104
   authentication open
dot11 ssid Quake-35f8d4q9e5@365%lFh&ju#ef2
   vlan 108
   authentication open eap eap_methods
   authentication key-management wpa
dot11 holdoff-time 60
dot11 arp-cache optional
power inline negotiation prestandard source
dot1x timeout reauth-period server
username Cisco password 7 02250D480809
username ggg privilege 15 secret 5 $1$E4Ms$78SOM7s3gZ8QxU.mlnEpj.
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 104 key 1 size 128bit 7 80B78765DD670039FE1557E4BFB4 transmit-key
encryption vlan 104 mode wep mandatory
encryption vlan 108 mode ciphers tkip
encryption vlan 102 mode ciphers tkip
encryption vlan 105 mode ciphers tkip
ssid Courage-34idkeysNCswuZue3765#%@&
ssid Freedom-jKb%&552en@546AsdfG65eD
ssid Galaxy-73j4CA58fd66y3lKICK#%@&*
ssid Quake-35f8d4q9e5@365%lFh&ju#ef2
power local 17
packet retries 64 drop-packet
no preamble-short
channel 2412
station-role root
beacon dtim-period 4
no dot11 extension aironet
bridge-group 1
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.102
encapsulation dot1Q 102
no ip route-cache
no cdp enable
bridge-group 102
bridge-group 102 subscriber-loop-control
bridge-group 102 input-type-list 201
bridge-group 102 output-type-list 201
bridge-group 102 port-protected
bridge-group 102 block-unknown-source
no bridge-group 102 source-learning
no bridge-group 102 unicast-flooding
bridge-group 102 spanning-disabled
interface Dot11Radio0.104
encapsulation dot1Q 104
no ip route-cache
no cdp enable
bridge-group 104
bridge-group 104 subscriber-loop-control
bridge-group 104 input-type-list 201
bridge-group 104 output-type-list 201
bridge-group 104 port-protected
bridge-group 104 block-unknown-source
no bridge-group 104 source-learning
no bridge-group 104 unicast-flooding
bridge-group 104 spanning-disabled
interface Dot11Radio0.105
encapsulation dot1Q 105
no ip route-cache
no cdp enable
bridge-group 105
bridge-group 105 subscriber-loop-control
bridge-group 105 input-type-list 201
bridge-group 105 output-type-list 201
bridge-group 105 port-protected
bridge-group 105 block-unknown-source
no bridge-group 105 source-learning
no bridge-group 105 unicast-flooding
bridge-group 105 spanning-disabled
interface Dot11Radio0.108
encapsulation dot1Q 108
no ip route-cache
no cdp enable
bridge-group 108
bridge-group 108 subscriber-loop-control
bridge-group 108 input-type-list 201
bridge-group 108 output-type-list 201
bridge-group 108 port-protected
bridge-group 108 block-unknown-source
no bridge-group 108 source-learning
no bridge-group 108 unicast-flooding
bridge-group 108 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
dfs band 3 block
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
interface GigabitEthernet0.102
encapsulation dot1Q 102
no ip route-cache
bridge-group 102
no bridge-group 102 source-learning
bridge-group 102 spanning-disabled
interface GigabitEthernet0.104
encapsulation dot1Q 104
no ip route-cache
bridge-group 104
no bridge-group 104 source-learning
bridge-group 104 spanning-disabled
interface GigabitEthernet0.105
encapsulation dot1Q 105
no ip route-cache
no cdp enable
bridge-group 105
no bridge-group 105 source-learning
bridge-group 105 spanning-disabled
interface GigabitEthernet0.106
encapsulation dot1Q 106 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface GigabitEthernet0.108
encapsulation dot1Q 108
no ip route-cache
no cdp enable
bridge-group 108
no bridge-group 108 source-learning
bridge-group 108 spanning-disabled
interface BVI1
ip address dhcp client-id GigabitEthernet0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip radius source-interface BVI1
no logging trap
access-list 1421 permit
access-list 1421 permit
access-list 1421 permit 0.0.0.255
access-list 1421 permit 0.0.0.255
access-list 1421 permit 0.0.255.255
access-list 1421 permit 0.0.255.255
access-list 1421 permit 0.0.255.255
access-list 1421 permit 0.0.255.255
access-list 1421 deny   any
access-list 201 permit 0x0800 0x0000
access-list 201 permit 0x0806 0x0000
access-list 201 deny   0x0000 0xFFFF
snmp-server view NCC mib-2 included
snmp-server community TROUbleIStrouBLE view NCC RO
snmp-server community CHECKtheMAIL RO
snmp-server community HAVocREEk RW
snmp-server community 1aPe3nLnmDt4yVYmbgWoUVjJYz1 view NCC RO 1421
snmp-server community 1aUQ5DAIH2bTBlvJg6RFS5qfsr RO 1421
snmp-server community 1OGgsN21DI4q01QeeIhJGF961 RW 1421
snmp-server enable traps tty
tacacs-server host
tacacs-server host
tacacs-server directed-request
tacacs-server key 7 110A1D5347415C5B53737F7D2E26
radius-server attribute 32 include-in-access-req format %h
radius-server host auth-port 1812 acct-port 1813 key 7 10190C4A533C07185D50721569013D3C3638022F4E0E42400102773D0D481A5E0E
radius-server vsa send accounting
bridge 1 route ip
line con 0
line vty 5 15
sntp server
end

Similar Messages

  • The dot11Radio interface in AP 1250 stuck in reset status

    Anyone have idea why the dot11Radio interface in AP 1250 stuck in reset status? I have tried to no shutdown in CLI and enable in GUI but doesn't work.
    Aironet1250#sh ip int b
    Interface IP-Address OK? Method Status Protocol
    BVI1 10.1.119.67 YES manual up up
    Dot11Radio0 unassigned YES unset reset down
    Dot11Radio1 unassigned YES unset reset down
    GigabitEthernet0 unassigned YES other up up
    Aironet1250#
    Thanks in advance!

    oh, I forgot to assign ssid. It work now

  • Show interface status (IOS layer 2switch)

    Is it possible to modify the width of the column containing the description of the interfaces when I issue the "show interface status?" on IOS cisco switches?

    I don't believe so but you can type show interface description if you want to see the entire description that is associated to the port.
    HTH,
    Edison.

  • 861w - don't see dot11radio interface

    I'm new to Cisco equipment and just purchased the Cisco 861W ISR. I got the router configured on a basic level and used the Express setup to configure my WAN/internet. All that works fine.
    However, I can't find the dot11radio interface listed on my device. When I run "show ip interface brief" I get the following:
    Dialer0 unassigned YES NVRAM up up
    FastEthernet0 unassigned YES unset up down
    FastEthernet1 unassigned YES unset up down
    FastEthernet2 unassigned YES unset up down
    FastEthernet3 unassigned YES unset up down
    FastEthernet4 unassigned YES NVRAM up down
    NVI0 unassigned YES unset administratively down down
    SSLVPN-VIF0 unassigned NO unset up up
    Vlan1 10.0.0.1 YES NVRAM up up
    Wlan-GigabitEthernet0 unassigned YES unset up up
    wlan-ap0 unassigned YES NVRAM up up
    So, when I attempt to go into config terminal mode and type in "interface dot11radio" so I can enable the radio with "no shutdown" I get an error message since dot11radio isn't present as an interface.
    I performed the factory reset on my new router several times while learning how to configure it. Have I somehow wiped out/disabled my wireless radio? Or is it possible I received a defective unit? This is the router I ordered http://www.pcconnection.com/IPA/Shop/Product/Detail?sku=8685745 Maybe I'm confused, but I thought this one came with the wireless radio built in, not as an option.
    Any advice would be appreciated.

    Problem could be due to the configuration while configuring,To Reset the Wireless Device to the Factory Default and again use the interface dot11radio global configuration CLI command to place the wireless device into the radio configuration mode. To reset the wireless device hardware and software to its factory default configuration, use the service-module wlan-ap0 reset default-config command in the router's Cisco IOS privileged EXEC mode.
    Here is the URL for the Factory default setting and administration guide for Cisco 860 series router, it may help you
    http://www.cisco.com/en/US/docs/routers/access/800/860-880-890/software/configuration/guide/admin_ap.html#wp1051827

  • Gigabit interface status faulty please help

    When I do a show interface status on 4500 switch I got a status faulty
    I did never see such thing
    Port- Name-Status-Vlan-Duplex-Speed Type
    Gi2/7-jsh3 faulty 188 full XXBaseSX
    Could you please help?
    Thanks a lot

    this usually indicates the port is faulty (bad; not working; will not work)
    this may have been set via the POST of the device. the internal tests failed and the port was marked FAULTY.
    this could also be the result of a good port simply went bad for some unknown reason.
    try to disable/reEnable the port. will probably still say faulty. (cannot initialize a faulty port)
    try to reset the blade the port is on, or the supervisor if it resides on that.
    do a "show test" (catOS) to see what the POST found when it did its powerOnSelfTests.
    i've seen plenty of FAULTY ports and 99% of the time, the port is simply bad and must be replaced. (usually an ASIC or the likes)

  • Interface dot11radio1 is reset down and does not works.

    I configured ssid and is a nonroot equipement and whwn I do sh ip inter brief the status interface dot11radio1 is reset and down and does not assosciate with the root AP
    This is the configuration:
    ip ssh version 1
    dot11 ssid fbpinto
    authentication open
    authentication shared
    authentication key-management wpa
    wpa-psk ascii 7 051C160E315F450F1B151E1C1F03
    dot11 network-map
    power inline negotiation prestandard source
    username Cisco password cisco
    bridge irb
    interface Dot11Radio0
    no ip address
    no ip route-cache
    shutdown
    station-role root bridge
    infrastructure-client
    bridge-group 1
    bridge-group 1 spanning-disabled
    no sh
    interface Dot11Radio1
    no ip address
    no ip route-cache
    encryption mode ciphers aes-ccm tkip
    ssid fbpinto
    antenna gain 9
    power client local
    station-role non-root bridge
    infrastructure-client
    bridge-group 1
    bridge-group 1 spanning-disabled
    interface FastEthernet0
    no ip address
    no ip route-cache
    duplex auto
    speed auto
    bridge-group 1
    bridge-group 1 spanning-disabled
    no sh
    interface BVI1
    ip address 172.27.119.10 255.255.255.128
    no ip route-cache
    no sh
    ip default-gateway 172.27.119.1

    Thanks very much!
    Then untilk the noonroot is not associate the interface radio remanis in  restet status protol down ¿is it?
    My problem is that this Brigge  working fine for a year ago but  one day fails and I replace the bridge  but the interface radio remain in status reset  too¿can be that the extenal antenna is broken? and therfore no signal received by the interface and can not associate with root for it?
    I try to put boths brigge close and test if interface radio is up and works fine .If works like this I think that is a problem with the extrenal anntena ( dipolo)
    regards

  • Access Point (AIR-CAP3702I-E-K9 ) 'sh ip interface ' output shows method is TFTP

    Hi all 
    Ip interface brief ,  method TFTP 
    Access Point  (AIR-CAP3702I-E-K9  )   'sh ip interface '   output shows method is TFTP 
    Interface
    IP-Address
    OK?
    Method
    d Status
    Protocol
    BVI1
    10.0.0.50
    YES
    TFTP
    up
    up
    Dot11Radio0
    unassigned
    YES
    unset
    up
    up
    Dot11Radio0.28
    unassigned
    YES
    unset
    up
    up
    Dot11Radio0.85
    unassigned
    YES
    unset
    up
    up
    Dot11Radio0.250
    unassigned
    YES
    unset
    up
    up
    Dot11Radio1
    unassigned
    YES
    unset
    administratively
    down down
    GigabitEthernet0
    unassigned
    YES
    TFTP
    up
    up
    GigabitEthernet0.28
    unassigned
    YES
    unset
    up
    up
    GigabitEthernet0.85
    unassigned
    YES
    unset
    up
    up
    GigabitEthernet0.250
    unassigned
    YES
    unset
    up
    up
    Thank you

    This tells us the configuration obtained via TFTP. 
    Does this AP get config via TFTP ?
    HTH
    Rasika
    **** Pls rate all useful responses ****

  • Battery status showing "not charging" when power adapter is plugged in

    I just bought a brand new Magsafe adapter 60w for my macbook but it seems that when i plugged in to my macbook, the battery status showed "not charging".  I have to disconnect and plug in again.  This also happened when I used my previous power adapter, that is why I got a new one.  Is this a common problem?  Please advise what could be done.

    Hi
    Try resetting the SMC. This sometimes solves this type of problem, in fact, it's listed as one of the reasons why you should try this:
    http://support.apple.com/kb/ht3964
    Bob

  • Purchase Order has approved but Status show as Unapproved

    Dear All Experts,
    I have a Purchase Order need to go throught approval procedure. The Purchase Order has approved by user and add into system and printed out. When second time, open the same Purchase Order, the status show "Unapproved" but the Purchase Order windows header name show Purchase Order [Approved], this make user unable to copy to GRPO. I have try to restore stored procedures in SAP B1, it does not make any changes. The user is using SAP B1 2007A SP0 PL49. Please Advise.

    Hi Angie
    the purchase order once approved has to be added on to the system after approval if u say that u have added the purchase order after it got approved then that seems to be a concern for that u need to contact ur sap partner or if u are a partner then u need to get in touch with sap to resolve the isssue as it could be because of problem with ur database
    but before that please be sure off that u are using the correct way and have sucessfully added the documnt apon approval.
    Regards,
    Manish

  • Sale order status showing being processed

    Dear Friends,
    I am working in SAP ECC 6.0
    My sale order Qty is 10 pcs eing processed
    and delivery qty is 10 pcs - Completed
    Good Issue - 10 Pcs - Completed
    Invoice - 10 Pcs - Completed
    In spite of carrying out full delivery sale order status is still showing being processed.
    is there any configuration missing or is there any program to update the status.
    Kindly advice.
    Satish

    Hi Ankur,
    2 Doubts i have:
    1)
    In our case for the Item Category we have not maintained anything in Completion Rule however we have maintained Update Document Flow in Order to Delivery Copy Control.
    Our Document status shows as Completed in this case as well. Hence i do not know the Significance of maintaining Completion rule in item category.
    2) I have a order type which has Order Relevant Billing. The Copy Control for Order to Billing does not have any Update Document Flow Check Box. We are using a Service Material in this Order Type.
    After creating the Billing we still have Order status as Being Processed.
    Can you help in finding a solution to the above?
    Madhukar

  • How can I use the color adjustments interface that shows up for camera RAW on jpeg files?

    How can I use the color adjustments interface that shows up for camera raw on other files types? The HLS controls had the secondary color adjustments (6 colors instead of the 3). Plus, it had same vibrancy and a better Curves interface. Yesterday was the first time I imported raw into Photoshop CS5 and I got that really cool interface. What is that? Can I use that on other file formats?

    Actually I am using the Tradional Chinese Version, when I try to edit the jpg file with camera raw, the system shows that there is no camera raw plug-in. The cmaera raw never work.

  • Sales Order Status showing  Being Processed

    Hi All ,
    I my client created sales order with 100000.700 ton and with 42 Piratical delivery document with different dates and 42 billing document and clear accounting documents
    But the problem is Sales order status showing as Being Processed
    I check all delivery documents if was showing total quantity delivers and i check copy controls OR to ZLF Updated document flow is there
    and i Item category TAN don't not having completion rule
    My question is it is mandatory to maintain Completion rule in item category
    The Problem With Only One sales order it showing Being Processed, rest of sales document Showing completed
    Do we need to Updated Status manually ?
    Can any one guide me what could be a Problem
    Thanks
    Rajesh

    Hi,
            GO TO VA02 THEN SELECT THE ITEM  THEN GO TO SCHEDULE LINE -> STATUS TAB-> GIVE THE REASON FOR REJECTION
    Regards,
    T.Murugu

  • For one Urgent Change during performing the Approval(chnging the status to 'To be Tested') system does not recognize any changes using the CTS WBS BOM in the development system. The transaction is therefore incorrect or the status was reset by the system.

    For one Urgent Change while performing the one of the Approval before changing the status to 'To Be Tested'
    We are getting below error.
    The system does not recognize any changes using the CTS WBS BOM in the development system. The transaction is therefore incorrect or the status was reset by the system.
    COuld anyone please help us to know, How it can be resolved?
    We also have this below error.
    System Response
    If the PPF action is a condition check, the condition is initially considered as not met, and leads to another warning, an error message, or status reset, depending on the configuration.
    If the PPF action is the execution of a task in the task list, and the exception is critical, there is another error message in the document.
    Procedure
    The condition cannot be met until the cause is removed. Analyze all messages in the transaction application log.
    Procedure for System Administration
    Analyze any other messages in the task list application log, and the entries for the object /TMWFLOW/CMSCV
    Additional Information:
    System cancel RFC destination SM_UK4CLNT005_TRUSTED, Call TR_READ_COMM:
    No authorization to log on as a trusted system (Tr usted RC=0).
    /TMWFLOW/TU_GET_REQUEST_REMOTE:E:/TMWFLOW/TRACK_N:107
    For above error Table /TMWFLOW/REP_DATA_FLOWwas refreshed as well but still the same error.

    If you are in Test System, you can use function module AA_AFABER_DELETE to totally delete the depreciation area (tcode SE37, specify chart of depreciation and depreciation area), After that recreate your depreciation area and run AFBN. But before you do that, have you created a retirement transaction type that limits the posting on your new depreciation area? If not create one.
    Hope this helps.
    Thanks!
    Jhero

  • Has anyone upgraded the Ironport ESA to 8.5.6-074 and had the issues of Raid status showing unknown?

    Has anyone upgraded the Ironport ESA to 8.5.6-074 and had the issues of Raid status showing unknown? After we upgraded our appliances we are having issues with our ESA appliances showing the RAID status as unknown. When we reported the issue to CISCO we were updated there were no issues reported at all. Could anyone please confirm if you have experienced the same issue. 

    You should see OPTIMAL - meaning the drives in the C170 are in good health/status:
    myc680.local> version
    Current Version
    ===============
    UDI: C680 V FCH1611V0B2
    Name: C680
    Product: Cisco IronPort C680 Messaging Gateway(tm) Appliance
    Model: C680
    Version: 8.5.6-074
    Build Date: 2014-07-21
    Install Date: 2014-07-29 11:16:34
    Serial #: xxx-yyy1611Vzzz
    BIOS: C240M3.1.4.5.2.STBU
    RAID: 3.220.75-2196, 5.38.00_4.12.05.00_0x05180000
    RAID Status: Optimal
    RAID Type: 10
    BMC: 1.05
    There are times post-reboot, that you'll see and get notification of RAID sub-optimal --- meaning that the appliance is running through on a health-check of the appliance's RAID.  You should be getting a notification once RAID status has returned to OPTIMAL, or as per the older OS revisions, READY:
    myc170.local> version
    Current Version
    ===============
    UDI: C170 V01 FCH1428V06A
    Name: C170
    Description: Cisco IronPort C170
    Product: Cisco IronPort C170 Messaging Gateway(tm) Appliance
    Model: C170
    Version: 7.6.3-019
    Build Date: 2013-06-09
    Install Date: 2014-09-12 13:52:24
    Serial #: xxxxxxD87B39-yyyyyy8V06A
    BIOS: 9B1C115A
    RAID: 02
    RAID Status: READY
    RAID Type: 1
    BMC: 2.01

  • SAP R/3 in order status showing accounting documnet not cleared

    Hi All,
    SAP R/3 in order status showing accounting documnet not cleared but when i checked in billing document and customer account its showing posted but order showing...same error.
    Thanks in Advance..
    URS,
    PURI......

    Hi Venkat,
           Please Check the Billing Document its Transfer Status must have been Indicating Not Transferred to R3,Since the Order has Errors in it the Billing Document, Error Order's does not replicate to R3 so the Sales Order need to be made Error Free and Then try to Repost the Billing it shall get Transferred to R3.
    Please Suggest the error in Sales Order for Further Help
    Hope is Answers your query
    Thanks and Regards,
    RK.

Maybe you are looking for

  • Task seqence according to departments in a company and MDT 2013

    Hi, I have a problem and I need help from the SCCM community. So here we go: I am in a process of upgrading SCCM from 2007 to 2012, great. I have setup lab environment which consists of 2 DC, 1 DB server, 1 SCCM 2012 Server and 2 test clients (Window

  • Right Click,Context Menu problem in Page Personalize

    Hi All, I am using EP6.40 and SP 13.  When I right click on portal content, showing context menu. I entered into Page Personalize  page by clicking options icon(Right-top corner of the page)-> personalize, a pop up window opened. In there, When I rig

  • How to embed an Image onto a Shape?

    I'd like to use Shape.contains() and intersects() functionalities on clipped free-form Images on a custom component. Could we embed an Image into a Shape? If the answe is yes, then, how? If Shape is not usable, then, how could we achieve similar func

  • JTextPane - Need to override TAB insert for traversal

    I am using the JTextPane for HTML support. I want the TAB key to default to traversing components instead of inserting tabs or spaces. For JTable and JTextArea I was able to clear the focus traversal keys and they correctly defaulted to the standard

  • Previous version Edge reflow?

    Hi all! can I download the previous version from somewhere Edge reflow? With the latest I can not work because nothing seem to work properly and the special characters are not supported. greetings! Dan