The dot11Radio interface in AP 1250 stuck in reset status

Anyone have idea why the dot11Radio interface in AP 1250 stuck in reset status? I have tried to no shutdown in CLI and enable in GUI but doesn't work.
Aironet1250#sh ip int b
Interface IP-Address OK? Method Status Protocol
BVI1 10.1.119.67 YES manual up up
Dot11Radio0 unassigned YES unset reset down
Dot11Radio1 unassigned YES unset reset down
GigabitEthernet0 unassigned YES other up up
Aironet1250#
Thanks in advance!

oh, I forgot to assign ssid. It work now

Similar Messages

Dot11Radio0 stuck in reset status after changing the station role

Hi Everyone.
I've got a AIR-AP1231G-A-K9 router. IOS has been upgraded to the latest version c1200-k9w7-mx.123-8.JED. Everything worked fine before I change the station role from root to repeater or workgroup bridge. Following is my configuration:
ap#sh run
Building configuration...
Current configuration : 1224 bytes
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname ap
enable secret 5 $1$KHHu$bN/odUmHdmb.0cwa57GYs1
ip subnet-zero
no aaa new-model
dot11 syslog
dot11 ssid Lanyard
authentication open
username Cisco password 7 123A0C041104
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
ssid Lanyard
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address 11.11.11.1 255.255.255.0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip radius source-interface BVI1
bridge 1 route ip
line con 0
line vty 0 4
login local
line vty 5 15
login
end
ap#sh ip int bri
Interface IP-Address OK? Method Status Protocol
BVI1 11.11.11.1 YES NVRAM up up
Dot11Radio0 unassigned YES NVRAM up up
FastEthernet0 unassigned YES NVRAM up down
ap#
Then I changed the station role
ap#conf t
ap(config)#int dot 0
ap(config-if)#station-role repeater
ap(config-if)#end
ap#sh ip int brie
Interface IP-Address OK? Method Status Protocol
BVI1 11.11.11.1 YES NVRAM down down
Dot11Radio0 unassigned YES NVRAM reset down
FastEthernet0 unassigned YES NVRAM up down
ap#
Interface Dot11Radio0 stuck in reset. No matter I reload or powercycle the AP, I still get the same reset status on Dot11Radio0.
Please help! Any input will be appreciated.

In order to get either the repeater or the workgroup bridge functionality working, you would likely need to have a Cisco AP as root. This is because the repeater and workgroup-bridge functionalities require Cisco Aironet Information Element (IE), which requires a Cisco root AP. There is no standard for interoperability for these functionalities (not part of any 802.11 standards). You can always try to connect them, making sure that they are using the same authentication/encryption configuration. However, it is unlikely to work.

861w - don't see dot11radio interface

I'm new to Cisco equipment and just purchased the Cisco 861W ISR. I got the router configured on a basic level and used the Express setup to configure my WAN/internet. All that works fine.
However, I can't find the dot11radio interface listed on my device. When I run "show ip interface brief" I get the following:
Dialer0 unassigned YES NVRAM up up
FastEthernet0 unassigned YES unset up down
FastEthernet1 unassigned YES unset up down
FastEthernet2 unassigned YES unset up down
FastEthernet3 unassigned YES unset up down
FastEthernet4 unassigned YES NVRAM up down
NVI0 unassigned YES unset administratively down down
SSLVPN-VIF0 unassigned NO unset up up
Vlan1 10.0.0.1 YES NVRAM up up
Wlan-GigabitEthernet0 unassigned YES unset up up
wlan-ap0 unassigned YES NVRAM up up
So, when I attempt to go into config terminal mode and type in "interface dot11radio" so I can enable the radio with "no shutdown" I get an error message since dot11radio isn't present as an interface.
I performed the factory reset on my new router several times while learning how to configure it. Have I somehow wiped out/disabled my wireless radio? Or is it possible I received a defective unit? This is the router I ordered http://www.pcconnection.com/IPA/Shop/Product/Detail?sku=8685745 Maybe I'm confused, but I thought this one came with the wireless radio built in, not as an option.
Any advice would be appreciated.

Problem could be due to the configuration while configuring,To Reset the Wireless Device to the Factory Default and again use the interface dot11radio global configuration CLI command to place the wireless device into the radio configuration mode. To reset the wireless device hardware and software to its factory default configuration, use the service-module wlan-ap0 reset default-config command in the router's Cisco IOS privileged EXEC mode.
Here is the URL for the Factory default setting and administration guide for Cisco 860 series router, it may help you
http://www.cisco.com/en/US/docs/routers/access/800/860-880-890/software/configuration/guide/admin_ap.html#wp1051827

Unable to set the speed on dot11Radio Interface

Hello Experts,
I have number of 1130ag access points in our network. The problem i am facing is that when I tried to set the speed on the dot11Radio 0 and 1 interface it doesn't appear
This is the command I am using:
interface dot11Radio 0
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
Please can someone help me.

Hi,
The configurations that you are entering.. that is..
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
is the Default config for 802.11G and by nature the default configurationas will not appear in the running config.. another example is.. By default Aironet Extentions are enabled on the AP runing config, and in the Show run you will see that.. but when you isue the command no dot11 extension aironet thne this command wil show up!! please make the change and then you will be able to see.. here is the link as well which can be used to set the values..
http://www.cisco.com/en/US/docs/wireless/access_point/12.4_21a_JA1/configuration/guide/scg12421aJA1-chap6-radio.html#wp1101903
lemme know if this answered your question
Regards
Surendra

Stuck using the Comparable Interface

I am having problems implementing the Comparable Interface in my class. I have written the compareTo method but this is not working. Can anyone see what I am doing wrong in the coding of this method. Thanks !!. (see below code for the class :
package tma02q1;
import java.util.*;
This is the outline of the basic Video class.
Such a class describes the videos stocked by a branch of a video hire company
As well as completing the given methods you will need to make further additions
to this class.For further details you should study the BranchTest class.
public class Video implements Comparable {
// declare two instance variables
// a String to hold the video title
// an int to hold the video rental cost - cost is held in pence
private String aTitle;
private int aCost;
public Video(String aTitle, int aCost) {
this.aTitle = aTitle;
this.aCost = aCost;
private void setTitle(String aTitle) {
this.aTitle = aTitle;
public String getTitle() {
return aTitle;
private void setRentalCost(int aCost) {
this.aCost = aCost;
public int getRentalCost() {
return aCost;
public String toString() {
return "Video Title = " + aTitle + " which has a rental cost of = " + aCost;
public boolean equals(Object vid) {
Video arg = (Video) vid;
return (this.aTitle.equals(arg.aTitle)
&&this.aCost==arg.aCost);
public int compareTo(Object vido) {
Video arg = (Video) vido;
int comp = aCost.compareTo(arg.aCost);
return comp;

You've got another serious problem with your code. Both the equals and compareTo methods will throw a ClassCastException if the parameter is not a reference to a video object. Using the instanceof operator will however solve the problem. E.g.
public boolean equals(Object o) {
if (o instanceof Video) {
    Video arg = (Video) o;
    return (this.aTitle.equals(arg.aTitle)
            &&this.aCost == arg.aCost);
else
    return false;
}The same approach is applicable to the compareTo method.
Regards

Two ssids in one Dot11Radio interface

Hello,
Whilst configuring CISCO867-W router I have encoutered the following problem.
On built-in access point I have one Dot11Radio interface. Is it possible to have two ssids associated with two different vlans on one interface? If yes, how to do it? If no, is there any solution to have two separated wlans on an access-point with one Dot11Radio?

Of course you can have two wlans associated with two different vlans on the same radio interface.
Here is a simple example on how to it?
on the router the most important thing you have to make sure that the interface
Wlan-GigabitEthernet0 is configured as trunk and allowing the vlans mapped on the ssids defined under the radio interface of the embedded AP. Also you have to make sure that dhcp pools have been defined for both vlans.
Assuming that you have two ssids:
ssid1 & ssid2 mapped to vlans 1 and 2 consecutively. vlan 1 has been defined as the native on the trunk defined on
Wlan-GigabitEthernet0
AP(config)#dot11 ssid ssid1
                #authentication open
                #vlan 1
               #exit
AP(config)#dot11 ssid ssid2
               #authentication open
               #vlan 2
               #exit
AP(config)#interface dot11radio 0
              #ssid ssid1
              #ssid ssid2
              # no shut
              # exit
AP(config)#int dot11radio 0.1
               #encapsulation dot1q 1 native
               #bridge-group 1
               #exit
AP(config)#int dot11radio 0.2
               #encapsulation dot1q 2
               #bridge-group 2
               #exit
AP(config)#int gig 0.1
               #encapsulation dot1q 1 native
               #bridge-group 1
               #exit
AP(config)#int gig 0.2
               #encapsulation dot1q 2
               #bridge-group 2
               #exit
Please Don't forget to mark the question as answered once having the right response

In SPROXY transaction ,the inbound interface is showing inactive.

HI i am having a proxy interface from PI to ECC. I made some changes to the structur of the message type in PI Repository ,
and in sproxy i regenerated the proxy and saved , but when i activate it it is getting activated but showing inactive at the end.
Can any body help me with this.
regards
sandeep

Hi,
What is the application release?
Was this working before? If yes, any changes have been done since then?
Please see if these documents help.
Note: 141685.1 - Unable to Close WIP Discrete Jobs
Note: 460061.1 - How To Check the Inventory Interface Manager's Status Programmatically
Note: 735186.1 - Outside Processing Transactions Occasionally Get Stuck In Pending Status.
Thanks,
Hussein

Aironet 1310 interface dot11 0 stuck in reset

Hi trying to connect two APs with one being root and the other non root. After configuring, the wireless interface on the non root remains stuck
int reset mode. Below is the error message i get and have tried and cant find out what the problem is.
%DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: No Response
Will appreciate any help. thanks

As per dmantill mention once we have a 1310 in root bridge and the other one in non root bridge the non root bridge will not enable the radio until it sees a good signal from the root bridge and its status will be reset down.
Remember that we have 2 types of 1310 the ones with build in antennas and the ones with no build in antenna and require and external antenna connected to it.
To know if your unit has a build in antenna or not the part number will not include a (-R) if it has a (–R) it means that the unit does not have a build in antenna.
Also remember that when we work with bridges we need to set them in install mode (install root bridge and install non root bridge)this mode will only allow the units to associate to each other and not pass traffic and the led’s on the back of the unit will stop works as usual and help us for antenna alignment between the units.
Here is the link that lets us know what each sequence we get on the leds once in install mode to know how god the antenna aliment or signal is.
http://www.cisco.com/en/US/docs/wireless/access_point/1300/installation/guide/130h_c3.html#wp1056656
Also remember that when working with bridges by defaults the units are set to work at full power and this would create 2 scenarios.
For example, if the units are able to cover up to 5km with full power if the distance between the units is more than 5 km then they will not be able connect and if the distance is shorter than 5 km let’s say 1 km and we leave the units at full power there is going to be too much interface and signal to noise on the connection due to the short distance between the units and at the end this could make the units not see a good signal between them.
For instance lets say we are on a football field and each of us is on a touchdown side and for us to be able to hear each other we need to scream to each other, but if we then walk to the center of the field and we keeping screaming we are going to hear ourselves but we will not be able to understand what we are saying to each other and we will need to lower our voice.
Here is the outdoor range calculation utility to check what is the exact distance we can cover with a unit and at an specific data rate.
http://www.cisco.com/en/US/products/hw/wireless/ps458/products_tech_note09186a008009459b.shtml
Just in case usefull links.
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008058f53e.shtml
http://www.cisco.com/en/US/products/hw/wireless/ps469/products_tech_note09186a0080508551.shtml
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_q_and_a_item09186a008015502c.shtml

AP 1252 dot11radio interface status shows RESET

Hi,
This is regarding an issue with one of my access point. The access point 1252 is autonomous one running the IOS version
C1250 Software (C1250-K9W7-M), Version 12.4(10b)JDA3, RELEASE SOFTWARE (fc1)
The status of the dot11Radio 0 interface is showing as RESET. I have pasted the interface brief details below.
ap03#
ap03#
ap03#sh ip int brief
Interface                  IP-Address      OK? Method Status                Protocol
BVI1                       <ipaddress>       YES DHCP   up                    up
Dot11Radio0                unassigned      YES TFTP   reset                 down
Dot11Radio0.102            unassigned      YES unset reset                 down
Dot11Radio0.104            unassigned      YES unset reset                 down
Dot11Radio0.105            unassigned      YES unset reset                 down
Dot11Radio0.108            unassigned      YES unset reset                 down
Dot11Radio1                unassigned      YES TFTP   administratively down down
GigabitEthernet0           unassigned      YES TFTP   up                    up
GigabitEthernet0.102       unassigned      YES unset up                    up
GigabitEthernet0.104       unassigned      YES unset up                    up
GigabitEthernet0.105       unassigned      YES unset up                    up
GigabitEthernet0.106       unassigned      YES unset up                    up
GigabitEthernet0.108       unassigned      YES unset up                    up
ap03#
Due to this the clientsa re not getting associated.
I tried rebooting the AP; shut the dot11radio0 interface and unshut it; verified the switch end duplex speed settings. Looks good.
Can anyone suggest me how to proceed?
Thankyou.

Hi,
Yes the Access Point was working fine all these days and for the last one week, I am facing this problem. Please find the running configuration of the Access point as below..
Building configuration...
Current configuration : 8275 bytes
version 12.4
no service pad
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
hostname ap03
logging buffered 65536 notifications
enable secret 5 $1$.WG7$dvJpY1XHuixBk3wA4sfR3/
aaa new-model
aaa group server radius rad_eap
server auth-port 1812 acct-port 1813
aaa authentication login default group tacacs+ local enable
aaa authentication login eap_methods group rad_eap
aaa authorization exec default group tacacs+ local
aaa accounting exec default start-stop group tacacs+
aaa session-id common
clock timezone MST -7
clock summer-time MDT recurring
ip rcmd rsh-enable
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host ncc ncc
ip rcmd remote-host ncc ncc
ip rcmd remote-host ncc ncc
ip rcmd remote-host ncc ncc
ip rcmd remote-host ncc ncc
ip rcmd remote-host ncc ncc
ip rcmd remote-host ncc ncc
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host netsvcs netsvcs enable
ip rcmd remote-host netsvcs netsvcs enable
ip rcmd remote-host netsvcs netsvcs enable
ip rcmd remote-host netsvcs netsvcs enable
ip rcmd remote-host netsvcs netsvcs enable
ip rcmd remote-host netsvcs netsvcs enable
ip rcmd remote-host netsvcs netsvcs enable
ip rcmd remote-host netsvcs netsvcs enable
ip rcmd remote-host netsvcs netsvcs enable
ip rcmd remote-host datacom datacom enable
ip domain list u04129.albertsons.com
ip domain list albertsons.com
ip domain name u04129.albertsons.com
ip name-server
ip ssh time-out 90
dot11 activity-timeout unknown default 28800
dot11 ssid Courage-34idkeysNCswuZue3765#%@&
   vlan 102
   authentication open eap eap_methods
   authentication key-management wpa
dot11 ssid Freedom-jKb%&552en@546AsdfG65eD
   vlan 105
   authentication open eap eap_methods
   authentication network-eap eap_methods
   authentication key-management wpa
dot11 ssid Galaxy-73j4CA58fd66y3lKICK#%@&*
   vlan 104
   authentication open
dot11 ssid Quake-35f8d4q9e5@365%lFh&ju#ef2
   vlan 108
   authentication open eap eap_methods
   authentication key-management wpa
dot11 holdoff-time 60
dot11 arp-cache optional
power inline negotiation prestandard source
dot1x timeout reauth-period server
username Cisco password 7 02250D480809
username ggg privilege 15 secret 5 $1$E4Ms$78SOM7s3gZ8QxU.mlnEpj.
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 104 key 1 size 128bit 7 80B78765DD670039FE1557E4BFB4 transmit-key
encryption vlan 104 mode wep mandatory
encryption vlan 108 mode ciphers tkip
encryption vlan 102 mode ciphers tkip
encryption vlan 105 mode ciphers tkip
ssid Courage-34idkeysNCswuZue3765#%@&
ssid Freedom-jKb%&552en@546AsdfG65eD
ssid Galaxy-73j4CA58fd66y3lKICK#%@&*
ssid Quake-35f8d4q9e5@365%lFh&ju#ef2
power local 17
packet retries 64 drop-packet
no preamble-short
channel 2412
station-role root
beacon dtim-period 4
no dot11 extension aironet
bridge-group 1
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.102
encapsulation dot1Q 102
no ip route-cache
no cdp enable
bridge-group 102
bridge-group 102 subscriber-loop-control
bridge-group 102 input-type-list 201
bridge-group 102 output-type-list 201
bridge-group 102 port-protected
bridge-group 102 block-unknown-source
no bridge-group 102 source-learning
no bridge-group 102 unicast-flooding
bridge-group 102 spanning-disabled
interface Dot11Radio0.104
encapsulation dot1Q 104
no ip route-cache
no cdp enable
bridge-group 104
bridge-group 104 subscriber-loop-control
bridge-group 104 input-type-list 201
bridge-group 104 output-type-list 201
bridge-group 104 port-protected
bridge-group 104 block-unknown-source
no bridge-group 104 source-learning
no bridge-group 104 unicast-flooding
bridge-group 104 spanning-disabled
interface Dot11Radio0.105
encapsulation dot1Q 105
no ip route-cache
no cdp enable
bridge-group 105
bridge-group 105 subscriber-loop-control
bridge-group 105 input-type-list 201
bridge-group 105 output-type-list 201
bridge-group 105 port-protected
bridge-group 105 block-unknown-source
no bridge-group 105 source-learning
no bridge-group 105 unicast-flooding
bridge-group 105 spanning-disabled
interface Dot11Radio0.108
encapsulation dot1Q 108
no ip route-cache
no cdp enable
bridge-group 108
bridge-group 108 subscriber-loop-control
bridge-group 108 input-type-list 201
bridge-group 108 output-type-list 201
bridge-group 108 port-protected
bridge-group 108 block-unknown-source
no bridge-group 108 source-learning
no bridge-group 108 unicast-flooding
bridge-group 108 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
dfs band 3 block
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
interface GigabitEthernet0.102
encapsulation dot1Q 102
no ip route-cache
bridge-group 102
no bridge-group 102 source-learning
bridge-group 102 spanning-disabled
interface GigabitEthernet0.104
encapsulation dot1Q 104
no ip route-cache
bridge-group 104
no bridge-group 104 source-learning
bridge-group 104 spanning-disabled
interface GigabitEthernet0.105
encapsulation dot1Q 105
no ip route-cache
no cdp enable
bridge-group 105
no bridge-group 105 source-learning
bridge-group 105 spanning-disabled
interface GigabitEthernet0.106
encapsulation dot1Q 106 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface GigabitEthernet0.108
encapsulation dot1Q 108
no ip route-cache
no cdp enable
bridge-group 108
no bridge-group 108 source-learning
bridge-group 108 spanning-disabled
interface BVI1
ip address dhcp client-id GigabitEthernet0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip radius source-interface BVI1
no logging trap
access-list 1421 permit
access-list 1421 permit
access-list 1421 permit 0.0.0.255
access-list 1421 permit 0.0.0.255
access-list 1421 permit 0.0.255.255
access-list 1421 permit 0.0.255.255
access-list 1421 permit 0.0.255.255
access-list 1421 permit 0.0.255.255
access-list 1421 deny   any
access-list 201 permit 0x0800 0x0000
access-list 201 permit 0x0806 0x0000
access-list 201 deny   0x0000 0xFFFF
snmp-server view NCC mib-2 included
snmp-server community TROUbleIStrouBLE view NCC RO
snmp-server community CHECKtheMAIL RO
snmp-server community HAVocREEk RW
snmp-server community 1aPe3nLnmDt4yVYmbgWoUVjJYz1 view NCC RO 1421
snmp-server community 1aUQ5DAIH2bTBlvJg6RFS5qfsr RO 1421
snmp-server community 1OGgsN21DI4q01QeeIhJGF961 RW 1421
snmp-server enable traps tty
tacacs-server host
tacacs-server host
tacacs-server directed-request
tacacs-server key 7 110A1D5347415C5B53737F7D2E26
radius-server attribute 32 include-in-access-req format %h
radius-server host auth-port 1812 acct-port 1813 key 7 10190C4A533C07185D50721569013D3C3638022F4E0E42400102773D0D481A5E0E
radius-server vsa send accounting
bridge 1 route ip
line con 0
line vty 5 15
sntp server
end

Listening for mail Acknowledgement a la the TransportListener interface

Hi gurus
I am using the TransportListener interface for listening to the acknowledgement sent by the mail server once it has recieved my Email. however now i am stuck with the 2 facts ..
1) What if the mail is stuck in traffic for a long long time ( looks like no one is immune to the omnipotent traffic jams :) ). I need to have a way of timing out the mail or something, i am not exactly sure how the other mail systems do it ,like "not being able deliver" error messages ( what are they based on)
2) when the acknowledgement has arrived and my listener class does all the relevent processing what happens to it. does it get GC or what?
please help me on this
Thanks
Tarun

I am not a MS kind of guy but I would suggest to check
opportunities with the new .Net integration. I know there are
already some tools in .Net world which you may consider to
integrate with CF.
This is just an idea.

ACLs on Dot11Radio interface blocks ALL traffic

On an AP1220 w/IOS 12.2(11)JA1, all traffic is blocked when an ACL is applied on either the RF interface or the FastE interface, even explicitly permitted traffic. Also, using the "log" command after an ACL line fails to log anything. Below is the ACL I want to apply to the Dot11Radio 0 interface. It blocks ALL traffic:
access-list 100 permit udp any any eq bootpc log
access-list 100 permit tcp any host 10.0.0.1 eq 1723 log
access-list 100 permit gre any host 10.0.0.1 log
access-list 100 deny ip any any log
Here is a test ACL that blocked ALL traffic, as well:
access-list 101 permit udp any any log
access-list 101 permit tcp any any log
access-list 101 permit icmp any any log
access-list 101 permit ip any any log
Both ACLs blocked all traffic and failed to log a single event. If the ACL is removed, everything works. HELP!

It's a known bug CSCec28612 - AP1200 access-list doesnt work on radio int with a log keyword

I can't move my application to navigate the tool bar. It is stuck under the Apple bar.

I can't move my application to navigate the tool bar. It is stuck under the Apple bar. I have a screen shot of it if I can figure out how to upload it. I can navigate and move all other applications, I have restarted computer, updated Adobe. any advice.

In that application what options are available to you under the Window menu item? Maybe something there that'll help?

Status LIS9 of the User interface MP000200 missing

Hi All,
While creating leaving action. System is giving error (Status LIS9 of the User interface MP000200 missing.
Mentions below are my configuration.
Infogroup
COP 0001 Org assignment
LIS9 0002 Personal Data
LIS9 0006 address
LIS9 0105 Communication
And Personnel Action type are:- 0 0 0 MSN20 (Tick) (Tick) (Not tick)
Let me know how to resolve it.
Regard
Ashish

Hi,
make sure that LIS9 should not be used to the Infotypes which are having Time Constraint 1
Check V_T582A for time constratints and also check V_T588D to remove the operation LIS9 forLeaving/ termination action.
for your information
Infotype 0002 should NEVER be delimited as part of the Leaving Action.
The help text for the Operations field of the Info Group states the following:
In the Leaving action, use the "delimit" (LIS9) operation to delimit records.
Please remove the infotype 0002 from the info group, then run the leaving action, you will not find an error message
The reason why you get the error is because the status LIS9 does not exist on MP000200 .
You can see this via the menu painter via SE41.
regards,
mohammed
Edited by: 0mohammed1 on Oct 14, 2011 1:51 PM

ASA 5505 getting dchp from the outside interface

Hi, i have this configuration on on the Asa client
: Savedz
: Written by enable_15 at 13:39:22.779 UTC Thu Aug 15 2013
ASA Version 8.2(5)
hostname Lakewood
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 172.100.2.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
ftp mode passive
pager lines 24
logging asdm informational
mtu outside 1500
mtu inside 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 172.100.2.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
dhcpd address 172.100.2.50-172.100.2.125 inside
dhcpd auto_config outside interface inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
this asa client is getting dhcp from another asa on another location, the asa on the other side cannot ping devices on the client side
this is the server asa
ASA Version 8.2(1)
name 50.66.169.176 OutsideWorld
name 172.100.2.0 Lakewood
interface Vlan1
nameif inside
security-level 100
ip address 172.100.1.254 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 50.66.202 255.255.255.248
interface Vlan3
shutdown
no forward interface Vlan1
nameif dmz
security-level 50
no ip address
interface Ethernet0/0
switchport access vlan 2
speed 100
duplex full
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
what type of configuration is this?
how can i get both sides to ping eachother and allow all the trafic?
thanks in advance.
Hi, i have this configuration on on the Asa client
: Savedz
: Written by enable_15 at 13:39:22.779 UTC Thu Aug 15 2013
ASA Version 8.2(5)
hostname Lakewood
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 172.100.2.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
ftp mode passive
pager lines 24
logging asdm informational
mtu outside 1500
mtu inside 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 172.100.2.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
dhcpd address 172.100.2.50-172.100.2.125 inside
dhcpd auto_config outside interface inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
this asa client is getting dhcp from another asa on another location, the asa on the other side cannot ping devices on the client side
this is the server asa
ASA Version 8.2(1)
name 50.66.169.176 OutsideWorld
name 172.100.2.0 Lakewood
interface Vlan1
nameif inside
security-level 100
ip address 172.100.1.254 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 50.66.202 255.255.255.248
interface Vlan3
shutdown
no forward interface Vlan1
nameif dmz
security-level 50
no ip address
interface Ethernet0/0
switchport access vlan 2
speed 100
duplex full
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
what type of configuration is this?
how can i get both sides to ping eachother and allow all the trafic?
thanks in advance.

Do you have a diagram of yourt setup and a more detailed description what you want to do?
The public interface of your main ASA looks like you are connecting to the internet. In that case, the IP address for the client has to come from the ISP and not from your main ASA.

Report to track changes to infotypes prior to running the payroll interfac

wants a report to track changes to infotypes prior to running the payroll interface. The attached report looks like it should work but it returns nothing. Is there config that turns on "Track Changes": for select infotypes? If so, can they be activated for key infotypes so this report will run?
Name, Address, position, etc.
Not attendance and absence ITs.

Hi,
IMG Personnel Management Personnel Admin Tools Revision Set up change document:
This node has three items:
Infotypes to be logged
Field Group Definitions
Field Group Characteristics
Using these three options you define which infotypes you wish to log, then which fields, then you define which groups of fields are to be saved. Click each link, or see the sections below:
Infotypes to be logged
Here you define which PA infotype numbers you require logging. Select New Entries and enter a transaction class (A for Pers Admin, B for recruitment), then enter the infotype number and save.
Field Group Definition
When changes are made to a logged infotype, the field contents before and after are recorded. This is the very reason for logging the infotype, but there is an overhead in performance and disk space used so it needs to be given consideration. Typically you will want to record fields that are pay relevant.
Using the field group definition, you specify which fields you wish to record changes in. When any of the fields in the group are changed, all the fields in the group are saved. You can use an asterisk to log all the fields of the infotype but this is not recommended for space and performance, also there are many fields on an infotype that you will not be using, that will be saved also. Ideally you will pick individual fields of the infotype and enter them like so:
The field group number is a freely defined number you allocate to the group, it will be used in the next step. For normal use, simply pick any number not already used in that infotype. All fields with the same field group number are recorded in the log, even if they have not changed.
Click New Entries and enter the infotype number, field group number and field names that you wish to record.
Field Group Characteristics
When you have set up the field group numbers, use the field group characteristics to activate the logging of those fields. You can also specify a supplementary field group; this means that the contents of another field group can also be saved at the same time, even though the contents have not changed. In practise it is not used much. Simply select new entries, enter the transaction class, infotype, and in the DocFieldGr enter the number you assigned to the field names that you want to store, then enter L for Long Term Documents (short are not supported)
The Audit Report
To access the report showing the logged infotype changes, use the HR report tree available from various menu paths, including:
Main Menu Human Resources Pers Management Administration Info System Reports - Documents Infotype change logged changes in infotype data. (RPUAUD00).
When you run the report, select the infotypes you require, and select and execute.
Cheers
Prasanth

The dot11Radio interface in AP 1250 stuck in reset status

Similar Messages

Maybe you are looking for