APPLE TV video set to incorrect value

I chose the HD setting on my apple TV and now I can not see anything. How do I get this back to normal? I know that I should not have selected this setting, but it happened. I hope someone can help. Steve

Can you hear the "boops" and "clicks" that the ATV makes when it use the remote to navigate the menu? If you can do this
Turn on Apple TV
1. Left until you hear "boop"
2. Down (clicks) until you hear "boop"
3. Right (click)
4. Press up until you hear boop
5. Down 3
6. Press center of Apple Remote
7. Down 1
8. Press center of Apple Remote
9. Go up until you hear "boop"
You should be at the top of TV Resolution
1. 780p HD
2. 1080i HD
3. 480P
4. 480I
Here is the Left Column at Start
Movies
TVShows
Music
Podcasts
Photos
Youtube
Settings (boop)
Pressing Settings takes you to
General
ScreenSaver
Audio
Video
Computers
Downloads
Pressing Video takes you to
Closed Captioning
TV Resolution
And TV Resolution takes you to the list above.
When you hear "boops" you are at the top, bottom, left or right in the menus.
Hope this helps.

Similar Messages

I am setting up my new iPhone 5s with back up from iCloud but only my expired applied is recognised. even though i put in the original correct password it is not accepted as message comes up that "your apple id or password is incorrect". I am stuck.

I am setting up my new iphone 5s using a back up from icloud. Problem arises when asked for Apple id and password the second time for store purchases. It shows my old expired Apple id (my old email address). There is no option to change the id and even when I put in the correct password for the old id (used originally) it kicks me out with the message ""Your Apple ID or password is incorrect" .. this is true as my apple id is wrong but I cant change it. Anyone know what I should do. Dont have access to my old deleted email account. Thanks

Hello jwpg,
Thank you for the details of the issue you are experiencing after restoring an iCloud backup. I recommend the following articles for an issue like this:
iCloud: "Incorrect Apple ID or Password" alert when setting up iCloud after upgrading to iOS 7
http://support.apple.com/kb/TS5207
iOS 7: If you're asked for the password to your previous Apple ID when signing out of iCloud
http://support.apple.com/kb/TS5223
Thank you for using Apple Support Communities.
Best,
Sheila M.

How to fix 'Unexpected error: Incorrect value: Location URL' in WSDL

Hi All,
Using SOAMANAGER transaction, I created a service ECC_CUSTOMERQUOTEERPCRTRC and its binding 'ECC_CUSTOMERQUOTEERPCRTRC_binding' using the Create Service option under the tab Configurations and using the web service definition 'ECC_CUSTOMERQUOTEERPCRTRC'. When I click on the link "Open WSDL document for selected binding" under the tab 'Overview', I get the following XML code in the popup window for the WSDL.
- <soap:Envelope xmlns:soap="http://schemas.xmlsoap.org/soap/envelope/">
- <soap:Body>
- <soap:Fault>
<faultcode>soap:Server</faultcode>
<faultstring>Unexpected error: Incorrect value: Location URL for subject IF {http</faultstring>
- <detail xmlns:slibfault="http://xml.sap.com/2005/11/esi/slib/fault/">
<slibfault:timestamp>Wed, 17 Nov 2010 22:29:02 GMT</slibfault:timestamp>
- <slibfault:exception>
<slibfault:text>Incorrect value: Location URL for subject IF {http://sap.com/xi/APPL/Global2}:CustomerQuoteERPCreateRequestConfirmation_In not found</slibfault:text>
<slibfault:position program="CL_SIDL_SUBJECT_ADAPTER=======CP" include="CL_SIDL_SUBJECT_ADAPTER=======CM006" line="47" />
</slibfault:exception>
</detail>
</soap:Fault>
</soap:Body>
</soap:Envelope>
The XML code for nthe WSDL displays an error 'Unexpected error: Incorrect value: Location URL for subject IF '. It looks like the code could find the required URL. Please let me know how to fix this error.
Thanks in advance.
--R D

Hello.
In SOAMANAGER delete your "unexpected" service (endpoint).
Then create it again.
If same error will occurs - try to delete all definitions of this service (include sicf-transaction) and then create it completely again.
Hope it helps.

Apple's Videos App on iPad won't load my shared library

Hi,
I've been looking for an answer to this problem for ages!
Symptoms/context:
You have all your movies onto one big drive
You have uncheck Preferences|Advanced|"Copy files to iTunes Media folder when adding to library"
(this way all titles will be linked to your big drive, not copied)
You have drag/drop those movies from your big drive in Finder into your iTunes Movies library
You have enabled Home Sharing (File|Home Sharing|Turn On Home Sharing)
You have disabled the old way of sharing (Preferences|Sharing tab|Uncheck "Share my library on my local network")
You have proudly added a very nice artwork for each of your movie so that you'll get nice thumbnails in iTunes
by using Identify.app
or by looking on the web for the best artwork (i.e. flickfacts.com), saving it locally, then drag/drop on your movie in iTunes (Get Info|Artwork)
You're using Apple's Videos app to load your shared library on you iPad
(Start Videos app,select your Shared library,wait a while,then all your thumbnails are displayed fine)
Then as the days go by, you realize that loading your library is taking more and more time, up until that day when all **** brakes loose and you get stuck at the small round clock progress bar, and you wait and wait but no thumbnails is coming up anymore. You reset everything to no avail. What happened?!!
Well here's what I had to do to fix that problem:
Everything is about movie thumbnails!
In my case I had an overhead of 0.5GB of thumbnails for 650 movies! That's an overhead alright! By overhead I mean that the sum of all my thumbnails was 500MB, so the Videos app had to load this (maybe not entirely at once but...) every time you start the app and select your shared library. This explain why the app get slower and slower has you add new movies, thus new thumbnails/artworks.
But this doesn't really explain why ultimately the Videos app stops loading all of a sudden!
I realize the iTunes doesn't like:
Movie that doesn't show the correct icon preview in Finder
Invalid movie formats - I'll explain later
Big thumbnails
Read all 3 steps and don't forget the last paragraph at the end.
Movies that doesn't show the correct icon preview in Finder
Ultimately, I think that was the main problem of all my 3 steps
In Finder, enable the Icon Preview:
View|Show View Options|Check "Show Icon Preview"
You should now be able to see you thumbnails like this in Finder:
VALID:
INVALID:
But if you see any of these icons, the Videos app on the iPad might stumble a bit when loading the library
or
If that's the case for some of your movies, you'll have to make sure that ALL your movies have a proper thumbnail.This can be achieve:
by using Identify.app - see (note1)
or by looking on the web for the best artwork (i.e. flickfacts.com), saving it locally, then drag/drop on your movie in iTunes (Get Info|Artwork)
Once the thumbnail is corrected, it should display fine in Finder and iTunes
Invalid movie formats
There might be some cases where even after correcting the thumbnail in step 1., this icon still remains invalid.
If that's the case, you'll need to:
Either delete the movie altogether and rip it again
or reconvert it. For example with iSkySoft iMedia Converter Deluxe has a "Speed conversion" option that allows you to reconvert a 2.5GB movie in about 5 min. After the re-conversion I just had to do step 1. and all was fine, and the thumbnail would show well in Finder/iTunes.
Big thumbnails - may be optional
To speed up the loading of the movie library you have to reduce the size of the artwork that you insert into each of your movie's metadata:
Get the artwork on the web (i.e. flickfacts.com) and preferably a .jpg format,and save it locally
Open your movie file with Preview (Apple's preview app)
Tools | Adjust Size
Fit into: 640x480 pixels + OK
Save As (press Option before Saving) and save it in another folder (I called my folder "Reduced to 640x480")
Note: if you want to do this on a bunch of files at once: select all your files in Finder, right click and select Open. All you .jpgs will be opened in Preview. Then Ctrl-A to select all in Preview, then you can resize them all)
You'll noticed that a 1.5MB artwork can easily reduced as small as 50K-200K.
For example, I went from 500MB to 72MB for all my artworks. Much smallest overhead wouldn't you say?!
Now comes the part you'll all love : you need to remove ALL your old big artworks for ALL your iTunes movies:
in iTunes | Movies
Right click on a movie|Get Info|Artwork tab|Select the artwork|Delete
Drag/drop your newly reduced .jpg to that same window
Click OK to save.
You can't do that in batch, you have to do each manually like this (if anyone has a better idea, I'm all ears)
See (note1)
(note1) Important: If you use a program like Identify.app to retrieve the metadata/artwork, I'm pretty sure the size of the automatically retrieved artwork is quite big by default (around 1.5MB-2MB) so you might wanna be careful here and use it to retrieve the movie's metadata, but after that do step 3. to replace the artwork with a smaller one.
VERY IMPORTANT
Once step 1, 2 are completed (and I had already completed the optional step 3) you have to remove all movies from iTunes (see note, next sentence ) and drag/drop them all back from your drive to your iTunes Movies window. BEFORE REMOVING ALL MOVIES FROM iTUNES, make sure that the option (Preferences|Advanced|"Copy files to iTunes Media folder when adding to library") was uncheck. If it was checked, I'm pretty sure it will delete all your movies on disk, not only in iTunes!!! - you'll have to investigate this yourselves or make sure you have a good backup copy of your movies first.
Since I've done all this, my iPad's Videos app is taking about 10-20 sec to load my over than 600 movies library
Pfew!!
Have fun gang,
Jean

This worked for me... A little time consuming but once you get rolling it goes GREAT... Thanks....
I got my artwork and saved it to my Desktop
Opened up Microsoft Paint and clicked on "File" and "Open" and found it to get it on the screen to resize it
Clicked "resize" and a box for changing it opened up
Checked the box "Pixels" and "Unchecked maintain aspect ratio"
Set Horizontal for 640 and Vertical for 480
Clicked on "OK" and went back to "File" and did a "Save As" and chose JPEG Picture
It came up "File Already Existed" and clicked "OK" (really did not care about the original artwork I found because wrong size)
Went to iTunes and on the movie right clicked on "Get Info", clicked on "Details", then "Artwork"
Go to the little box on the top left that shows your old artwork and click on it to get the little blue border to appear around it and hit "Delete" to make it gone
Click on "Add Artwork" and find it where you put the one from above on your Desktop and hit "Open" and OK and your new artwork is now there and all good.
Sounds like a lot of steps to follow but after around 5 or so you will fly through it. This worked perfect on my iPhone 6 Plus and I have artwork on my Home Videos now.

HT201269 I'm trying to restore my iCloud back up on my new iPhone 5s and keep getting "could not sign in your apple Id or password is incorrect. I noticed that the Id it's showing is not my complete email address. I've reset my password 5 times. It accept

I'm trying to restore my iCloud back up on my new iPhone 5s and keep getting "could not sign in your apple Id or password is incorrect. I noticed that the Id it's showing is not my complete email address. I've reset my password 5 times. It accepts my password when I install as a new phone. How can I resolve this so I can restore my back up?

Hello jwpg,
Thank you for the details of the issue you are experiencing after restoring an iCloud backup. I recommend the following articles for an issue like this:
iCloud: "Incorrect Apple ID or Password" alert when setting up iCloud after upgrading to iOS 7
http://support.apple.com/kb/TS5207
iOS 7: If you're asked for the password to your previous Apple ID when signing out of iCloud
http://support.apple.com/kb/TS5223
Thank you for using Apple Support Communities.
Best,
Sheila M.

Apple tv video quality vs hd tv and high def dvd's

ok...i know it supports 1080i, but does the video quality of video in itunes really look good compared against say a blu-ray disc, or hdtv signals? i'm sure it will get better (with a hardware or software upgrade?) if its not close to high def quality but want to know what i'm in store for if i buy appletv now...thanks. PS: i currently have directv HD and a ps3 for blu-ray, and my tv's are all HD...

Based on my own testing, the distinctions between an HD-DVD movie (which are true 1080) and an Apple TV video converted as its own maximum settings (which is 720) is actually quite noticeable if you have a 1080 TV set, but at the same I don't consider it a show-stopper. I watch a lot of HD broadcast content that's only 720p, and it's still very good.
An HD-DVD or Blu-Ray DVD will normally be in 1920 x 1080 resolution (1080p or 1080i, generally depending on your equipment). The Apple TV's maximum resolution is 1280 x 720 (basically 720p). Therefore, even an original HD-DVD or Blu-Ray DVD converted to Apple TV will need to be scaled down to 720p for display on the Apple TV.
Further, Elgato EyeTV actually scales these down somewhat lower, so HDTV recorded content could be even worse-off, depending on the original source. The standard Apple TV export settings use a 960 x 540 frame in order to keep the bit-rate and frame rate within tolerances (since a 720p signal is approximately 60fps, and the bitrates will generally exceed 5-6 mbps, which pushes the limits of the Apple TV).
Even more interestingly, Elgato's new turbo.264 dongle will only encode in "Apple TV" format at a maximum resolution of 800 x 600 (and if you do the math you will realize that this will be considerably less for a 16:9 aspect ratio video).
The result is that videos converted from an EyeTV Hybrid are technically much worse off on the Apple TV than viewing the original source material. Whether this is significant enough to be noticeable will depend on your output medium, but on my 62" DLP, the difference is quite apparent (although still far superior to an SDTV signal).
You can get 1280 x 720 content to play back at 60fps at 5mbps bit-rates on the Apple TV by using ffmpeg-based encoders and manually selecting higher settings, although it's been hit-and-miss in my own testing, and of course it creates gargantuan files. Elgato and others have obviously tried to stay with the more conservative settings to ensure that they can guarantee the broadcast possible range of support.
In fact, although most of the standard encoder settings max out at 2.5-3.0 mbps, I've successfully pushed up to 6 mbps through the Apple TV, although such content has to be synced rather than streamed, since even an 802.11n network has a hard time keeping up (it worked, but there were some drop-outs and glitches in the process). Of course, 6mbps content is going to fill up the Apple TV hard drive pretty quickly as well (you'd only be able to fit around 11 hours on the internal 40GB hard drive).
The other thing to keep in mind with DVD movies is that they come from film, which is a 24fps source (based on the physical nature of film). As a result, the distinctions between a 720p and 1080i signal are less prevalant when dealing with film content, since you won't get the full 60fps HDTV capabilities anyway. Interlacing can still create some nasty side-effects, but it's far less of an issue when you're dealing with less than half of the normal frames.
In my own experiences, I have an Apple TV that is connected to a 1080p upscaling DLP TV (native 1080i input, internalized de-interlacing), and a second Apple TV that is connected to a 720p LCD TV. With the first Apple TV, I can notice the difference between 720p and 1080i output settings only when viewing photos, since the remainder of the standard content doesn't exceed 720p anyway. Further, because my TV de-interlaces a 1080i signal to 1080p, I don't get the flicker that is normally associated with a 1080i signal.
On the second Apple TV, I leave the setting to 720p, since that's the native resolution of the second TV, and I get noticeable interlacing-based flickering on the 1080i, particularly with photo slideshows (mostly in the transitions).

Why is the iPod Touch (4th Gen) missing the video setting for TV Out?

Has anyone else noticed that in the iPod Touch (4th Gen) that there isn't a video setting for TV Out? It's not on the new iPhone either. I wanted to attach an AV Composite cord from my iPod to my TV. It won't work because of the missing video setting. You would think that since this is new technology, it would have that setting. After all, my iPod from 2005 has that feature and works just fine with the $39 AV Compostie cable from Apple. I was hoping to display what I have on my iPod Touch to my TV, but discovered that I couldn't. When I called Apple, they thought at first I had a defective cable. But later told me that i OS 5 left out the video out feature as if by mistake. Could anyone elaborate on this issue? I would appreciate it. Thanks!!

I am well aware that setting was on the iPod before iOS 5! My question is why is it missing? Because right now, Apple is selling the AV Composite cable claiming it's compatible with the iPod Touch (4th Gen) and it's not. Thank you!

Just bought Ipad2. Loaded Skype, can see and hear other person but cannot see myself cannot find a video setting for skype on the ipad does anyone know?

Just bought Ipad2. Loaded Skype, I can see and hear the other person, but They and I cannot see me...just my audio. Does anyone know where or how to find sype video setting on Ipad app?

Try a Reset [Hold the Home and Sleep/Wake buttons down together for 10 seconds or so (until the Apple logo appears) and then release. When the screen goes blank power On again in the normal way.] It is absolutely/appsolutely safe!

URGENT! Setting QoS DSCP value on switches

Hi,
I desperately need replies to my problem below.
I tried to set DSCP values to 2 applications, video and video conference, on cisco 3560 and cisco 2950 swtiches based on the source ip address of the servers.
So on the switches, I created an access-list to identify the servers' ip addresses.
Then I use "class-map match-any video" followed by "match access-group" for the access-list.
Then I use "policy-map policy1", then "class video" then "set dscp ef".
Finally I apply the policy to the INPUTS of all ports "service-policy input policy1"
But when I use a sniffer to sniff the ports, I see that the DSCP value is not "EF", instead it is "0x20, class 4".
Why is this so?
Where have I done wrongly?
Finally, on routers, where do I apply QOS policy? On input ports or output ports of routers?
I urgently need help.
Thank you.
Regards,
Rachel

Rachel,
Without seeing what you have in place so far, I'll see if I can answer some of those questions. If the switch connects to a router, then the outbound (egress) interface would in fact be that interface on the switch that connects to a router. Best practices dictate that the classification and marking should be done on the inbound (ingress) interface which connects the switch to the network where the host resides.
If you wanted to implement an end-to-end QoS solution, then you should configure QoS on every interface between the source and destination. This is because even FastE/GigE ports can become congested due to worm outbreak or DOS attack. But if all you want to do right now is guarantee bandwidth to the video traffic across the WAN, that can be accomplished by a) classifying and marking the video traffic as close to the source as possible, and b) configuring queuing/scheduling on the outbound WAN interface based on those markings.
Once the switch has marked the traffic with a DSCP value per (a), that DSCP value should remain intact until it reaches the WAN router per (b), and all the way until it reaches its destination. That is, unless there is a device somewhere in between that is remarking traffic. If the switch you reference is not directly connected to the router you reference, there could be another switch or router in between marking everything back to DSCP 0, meaning that all traffic is untrusted.
I don't have a 2950 here with me, but without checking syntax this is basically what you should have, if you just want to mark video traffic EF and then guarantee bandwidth on the wan:
2950:
access-list permit
class-map match-any VIDEO
match access-group
policy-map POLICY1
class VIDEO
set ip dscp 46 !
interface
service-policy input POLICY1
Router:
class-map match-any EF_VIDEO
match ip dscp 46
policy-map VIDEO_OUT
class EF_VIDEO
priority 1600
interface
service-policy output VIDEO_OUT
If you are sniffing traffic on that switch to ensure that video traffic is being marked, make sure that you are sniffing the outbound interface toward the router, not the inbound interface from the host. That will ensure that your sniffer trace picks up the traffic after it has been marked DSCP 46.
Just in case this post is related to your post where you want to lock the router WAN interface so that the 1.6 megs of video gets through but other traffic is dropped when the video takes the full 1.6 megs of bandwidth...
QoS queuing/scheduling only kicks in when the interface experiences congestion. If there is no congestion on the interface, traffic will still be marked and policed per the service policy, but not queued/scheduled - it will just fly right through the interface with the new markings. The only way to force such congestion at 1.6 megs is to use traffic shaping. You would need to shape the entire interface down to 1.6 megs, and THEN apply the priority bandwidth. This can be accomplished with a hierarchical policy-map as follows:
Router:
class-map match-any EF_VIDEO
match ip dscp 46
policy-map VIDEO_OUT
class EF_VIDEO
priority 1600
policy-map SHAPE_OUT
class class-default
shape average 1600000
service-policy VIDEO_OUT
interface
service-policy output SHAPE_OUT
I really hope I am helping you out here, please let me know how this works out. Good luck!
Best Regards
Robert

Apple website video problems

I have been having weird performance issues with the videos on the apple website in particular. Often it will work the first time I open Safari but once I try to click the next one, it just does not work (not even movement on the progress bar).
I recently updated to QT 7.4 and it seems that based on my looking for a solution, it may be related to that but nothing seems to solve it. I know some people may recommend Firefox but it seems that as a minimum the Apple website videos should work on Safari!
Any suggestions?

These are the downloads and the settings you need in order to view/hear pretty much everything that the net can throw at you: The setup described below has proved repeatedly successful on both PPC and Intel macs, but nothing in life carries a guarantee!
It is known to work in the great majority of cases with Safari 3.0.4, QT 7.3 or 7.4 and OS 10.4.11. (If you are running Leopard, ensure that all plug-ins have been updated for OS 10.5.2)
Assuming you already run Tiger versions OS 10.4.9 or above (this has not yet been verified with Leopard) and have Quicktime 7.2 or above, and are using Safari 2 or 3, download and install (or re-install even if you already had them) the latest versions, suitable for your flavor of Mac, of:
RealPlayer 10 for Mac from http://forms.real.com/real/player/blackjack.html?platform2=Mac%20OS%20X&product= RealPlayer%2010&proc=g3&lang=&show_list=0&src=macjack
Flip4Mac WMV Player from http://www.microsoft.com/windows/windowsmedia/player/wmcomponents.mspx (Windows Media Player for the Mac is no longer supported, even by Microsoft)
Perian from http://perian.org/
You should read this support page http://perian.org/#support in case you need to delete older codecs.
Adobe FlashPlayer should first be uninstalled using the appropriate uninstaller available here: http://kb.adobe.com/selfservice/viewContent.do?externalId=tn_14157&sliceId=2 and then the latest version obtained from here: http://www.adobe.com/shockwave/download/download.cgi?P1ProdVersion=ShockwaveFlash and installed.
(You can check here: http://www.adobe.com/products/flash/about/ to see which version you should install for your Mac and OS.)
In earlier versions than QT 7.1.3 in Quicktime Preferences, under advanced, UNcheck Enable Flash, and under Mime settings/Miscellananeous only check Quicktime HTML (QHTM).
You should also ensure, if you are running Tiger 10.4.11 or Leopard, that you have downloaded and installed the correct version for your Mac of Security Update 2007-009.1.1, which also deals with the Quicktime/Flash issues you may have experienced, such as the '?'. What happened was that both Quicktime as well as Adobe FlashPlayer tried to play the Flash video at the same time. This no longer happens. (N.B. Security Update 2007-009 1.1 requires both a restart and a permission repair.)
If you get problems with viewing video on a website try moving this file to your Desktop:
Hard drive/Library/Internet Plug-Ins/QuickTime Plugin.webplugin
and then restarting Safari. If all now works, you can trash that file.
In Macintosh HD/Library/Quicktime/ delete any files relating to DivX (Perian already has them). However it should be noted that Perian is not an internet plugin and will not play DivX files imbedded on a website. For that you will need the DivX Player browser plugin available from http://www.divx.com/divx/mac/
Now go to Safari Preferences/Security, and tick the boxes under Web Content (all 4 of them) to enable Java.
Lastly open Audio Midi Setup (which you will find in the Utilities Folder of your Applications Folder) and click on Audio Devices. Make sure that both Audio Input and Audio Output, under Format, are set to 44100 Hz, and that you have selected 'Built in Audio'.
Important: Now repair permissions and restart.
You should also consider having the free VLC Player from http://www.videolan.org/ in your armory, as this plays almost anything that DVD Player might not.

Help me to set a wrong value in DateField object

Hi all,
I have a DateField object in my View Bean, which is having three seperate drop down for Date,month and year. When user select a wrong input (For Eg: 31 Sep 2006), the Error Action Handler will return with (01 Oct 2006) value as Date object is linient. So is there any hope to set my previouse value in the field.
Thanks in Advance.

Are you asking if it's possible to make an incorrect
date default to the nearest correct date in the same
month?I meant, I want to set a wrong date object. As Date,Calendar and GregorianCalendar all are lenient in true in default, it will count the date value and go forward to the next date. I dont want to do this. I have to set the selected date as my date object.
Thanks

Confirm Apple Composite Video Cables Work

Before I shell out the $50 for the Apple Composite Video cable set I want to confirm that they will actually work to send video, TVshows, Movies from my 3rd Generation 8Ghz Nano Ipod to a TV through the composite (three plug) video plugs. Do they really work?

Yes - it works very well

Why I can't see Apple website videos on Samsung tablet? Used many browsers, same result...

I could not find a website issues community and this one was the closest I could find. If this needs to be moved to a different community, please do so.
I realize it's cross platforms, but web browsing should be the same for everyone, no matter what device is used.
I can watch Apple website videos just fine on Windows/Chrome browser (or IE, Firefox) but can't on Samsung Android/Chrome browser (also tried Firefox, Opera, Samsung browser).
Other websites embedded videos are working (i.e. youtube, vimeo, forums etc.) so far it is only the Apple website embedded videos that are not working.
Any idea why?

If it's any help, here is what Samsung Support says:
Please wait for a Samsung Agent to respond.
You are now chatting with 'Alberto'. There will be a brief survey at the end of our chat to share feedback on my performance today.
Your Issue ID for this chat is LTK1125603600195X
Alberto: Hi, thank you for reaching out to Samsung technical support. How may I assist you?
Alex: Hi there
Alex: Why I can't see Apple website videos on Samsung tablet? Used many browsers, same result...
Alex: I can watch Apple website videos just fine on Windows/Chrome browser (or IE, Firefox) but can't on Samsung Android/Chrome browser (also tried Firefox, Opera, Samsung browser). Other websites embedded videos are working (i.e. youtube, vimeo, forums etc.) so far it is only the Apple website embedded videos that are not working. Any idea why?
Alberto: Hello, I understand that you want to see apple website videos on Samsung tablet, is it correct?
Alex: correct
Alberto: Thank you for the confirmation.
Alberto: What is the model number of your tablet? It starts with GT/SM which can be found on the rear panel.
Alex: Don't have it with me but it's the Tab S 8.4
Alex: Same goes for my phone, Galaxy S5
Alberto: Okay,Do you see any error message while browsing?
Alex: nope, no error, it just won't play any video on apple website, ALL other websites videos are plaing OKare
Alex: playing Ok is what I meant
Alex: and this is the same for my tablet AND my phone
Alex: devices are updated to the latest software bla, bla
Alberto: Alright, please restart the tablet once.
Alex: scale of 1 to 10 on tech advance level, I am at 7-8, just so you don't take me through power recycle and such
Alex: you just did
Alex: it's not that
Alberto: Could you give me a few minutes while I gather the information for you?
Alex: you can grab a galaxy tablet or a phone and try for yourself and yo'll probably notice it won't work...
Alberto: I appreciate your time and patience.
Alberto: As you are able to see other website's embedded videos on your tablet, it could be an issue with the compatibility of Apple website.
Alberto: There should be no issue with the trablet as other websites are working fine.
Alex: Can you transfer me to your Guru tech person to see if I can get a more elaborate answer and maybe a fix for this?
Alex: Then why the apple videos work fine on windows PC and the ONLY ones not working are Android devices?
Alberto: I have rechecked the information.
Alberto: As you are facing an issue only with a particular web site there should not be issue with the Samsung tablet.
Alberto: Also tablet is working fine with other web sites which indicates that there is an issue with that particular web site.
Alberto: There is no separate setting on the tablet to access any particular web site.
Alex: This much I figured, problem is what is causing it and how it can be solved? Again, issue is only on Android devices. PC Windows and iOS devices work good
Alberto: I am afraid; Samsung do not have information about the issues with a particular web site.
Alberto: I would have surely helped, if there had been information available with me.
Alex: Yes, I was afraid you'll say this...
Alex: Do you have an android device there? Try it yourself and see it will not work. Whatever it is IT IS A PROBLEM!!!
Alberto: I understand your requirement; however, it will not be possible for me to check this from here.
Alberto: You need to contact the web site support for further assistance.
Alberto: Is there anything I might be able to assist you with?
Alex: yeah, it went as expected, no fix for this... do you have a level 2 or 3 or 4 tech there?
Alberto: I will transfer this chat to my supervisor.
Alberto: Please be online while I transfer this chat.
Alex: sure, thanks
Alberto: Not a problem.
Please wait while I transfer the chat to 'Sammy'.
You are now chatting with 'Sammy'. There will be a brief survey at the end of our chat to share feedback on my performance today.
Your Issue ID for this chat is LTK1125603600195X
Sammy: Hello Alex. I am the supervisor of Alberto.
Sammy: I am going through the previous chat session.
Alex: Ok, thanks
Sammy: You are welcome.
Sammy: I appreciate your time and patience.
Sammy: I see that you are unable to access Apple website videos on your tab.
Alex: and on my S5
Sammy: As you are able to access the videos from all the other web sites, it is not an issue with Samsung tab and Samsung do not have any control on this issue.
Sammy: It is an issue with that particular web site and you need to contact the web site support for further assistance.
Sammy: There is no separate setting on the tab to access a particular web site.
Alex: Yes, I need to do that. At this point it's the technical aspect that bothers me, not that I can't watch the video, I can use my iPhone or my PC to watch the video, but why the Android can't?
Alex: Thank you Alberto
Alex: or Sammy
Sammy: I understand your requirement; however, we do not have any information about this issue.
Alex: Ok, thanks
Sammy: I apologize for the inconvenience.
Sammy: Is there anything else I can assist you with?
Alex: no
Sammy: Thanks for chatting with Samsung Support. If you have a minute, please click on the blue “X close” button to receive the transcript of your chat and fill out a brief survey to help us serve you better.
Follow Samsung Service on Facebook, Twitter and YouTube.
Chat session has been terminated by the Samsung Agent.

Focus after Setting a Form Value within the Validate Event ( =8.8)

Hi
Setting Values within Validate Event sets Focus incorrectly on SAP >= 8.8
The following example works fine on SAP 2007.
Why i don't like this behaviour
-I didn't found an easy workaround to fix it
-SetMatrixCellWithoutValidation has the right behaviour but only works with Userdefined - Columns
-It's a quite common usecase to validate something and in the same step set some values after successful validating (or cancel the input by using BubbleEvent = False)
-It just worked for 6 years now
-I have developed around 20+ AddOns and i'm running into this Regression Issue more and more.
But maybe i'm just missing something.
So how would you solve the following code now with Versions >= 8.8 ?
Thanks for any enlightment!
private void SBO_Application_ItemEvent(string FormUID, ref SAPbouiCOM.ItemEvent pVal, out bool BubbleEvent)
            BubbleEvent = true;
            // 11.08.2011 knp
            // use case is for example setting the price according a custom price table
            // it's triggered by the item column in the sales order matrix and sets the unit price
            // Expected: Focus is on the column after "Item" column
            // Result:   Focus is on column after the "Unit Price" column
validation
            if (pVal.InnerEvent == false)
                if (pVal.EventType == SAPbouiCOM.BoEventTypes.et_VALIDATE)
                    if ((pVal.FormTypeEx == "139"))
                        if (pVal.BeforeAction == true)
                            if (pVal.ItemUID == "38")
                                if (pVal.ColUID == "1") // item code
                                    SAPbouiCOM.Matrix oMtx = (SAPbouiCOM.Matrix)SBO_Application.Forms.Item(pVal.FormUID).Items.Item("38").Specific;
                                    SAPbouiCOM.EditText oEd = (SAPbouiCOM.EditText)oMtx.Columns.Item("14").Cells.Item(pVal.Row).Specific;
                                    oEd.Value = "2";

Hi
Try this
private void SBO_Application_ItemEvent(string FormUID, ref SAPbouiCOM.ItemEvent pVal, out bool BubbleEvent)
            BubbleEvent = true;
            // 11.08.2011 knp
            // use case is for example setting the price according a custom price table
            // it's triggered by the item column in the sales order matrix and sets the unit price
            // Expected: Focus is on the column after "Item" column
            // Result:   Focus is on column after the "Unit Price" column
validation
            if (pVal.InnerEvent == false)
                if (pVal.EventType == SAPbouiCOM.BoEventTypes.et_VALIDATE)
                    if ((pVal.FormTypeEx == "139"))
                        if (pVal.BeforeAction == true)
                            if (pVal.ItemUID == "38")
                                if (pVal.ColUID == "1") // item code
                                    SAPbouiCOM.Matrix oMtx = (SAPbouiCOM.Matrix)SBO_Application.Forms.Item(pVal.FormUID).Items.Item("38").Specific;
                                    SAPbouiCOM.EditText oEd = (SAPbouiCOM.EditText)oMtx.Columns.Item("14").Cells.Item(pVal.Row).Specific;
                                    oEd.Value = "2";
                                    oMtx.Columns.Item("1").Cells.Item(pVal.Row).Click(SAPbouiCOM.BoCellClickType.ct_Regular, 0);
Regards
Arun

Can anyone confirm if you can in fact shoot/edit (perhaps using a less than best video setting) on a Canon XA20 or Sony HXR-NX30U with iMovie 10 (Mavericks)? I do not want to convert files. Thx.

Can anyone confirm if you can in fact shoot/edit (perhaps using a less than best video setting) on a Canon XA20 or Sony HXR-NX30U with iMovie 10 (Mavericks)? I do not want to convert files. Thx.

Hi road.north,
Welcome to the Support Communities!
The article below will help you determine which cameras are supported for iMovie '10
Apple - iLife Help - iMovie Supported Cameras
http://help.apple.com/imovie/10/cameras/en/index.html?lang=en_US
Cheers,
- Judy

APPLE TV video set to incorrect value

Similar Messages

Maybe you are looking for