ARP issues with 3750X & 2960X Stack

Unable to consistently ping a device from the 3750x that is connected to a vlan on the 2960x stack (po1 between 3750x and 2960x).  ARP statements appear normally in 3750x, where the interface vlan resides.  The device is pingable from through the 3750x, but not from the 3750x, even when specifying the Vlan Interface as the source.
Thanks for the help.

Connected device, then power cycled, then pinged:
lrs3750x-admin#ping 172.18.3.17             
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.18.3.17, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/7/34 ms
lrs3750x-admin#
Then, spiked the interface, because dot1x was lacking logs and not behaving properly:
lrs3750x-admin#      show arp | in 172.18.3.17          
Internet  172.18.3.17             0   Incomplete      ARPA
lrs3750x-admin#ping 172.18.3.17
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.18.3.17, timeout is 2 seconds:
Clear arp no longer fixes the issue for the device.
Thanks!

Similar Messages

  • ARP issue with Cisco 5505

    Hi there,
    We have an issue with our current ASA 5505 set up and I hope someone can help.  Here is the setup
    ISP Handoff -> L2 Switch -> VLAN 1 of ASA
                                          -> VLAN 2 of ASA
    The ISP handoff is a single ethernet cable but the ISP router is acting as the gateway for 2x seperate public address spaces.  ISP cable plugs into a L2 switch.  The two VLANS of the ASA are then plugged into the same switch, one VLAN configured for public space 1 and the other for public space 2, now the issue is when the firewall ARPs for the gateways VLAN2's gateway shows up on VLAN 1 and VLAN 2 which obviously causes issues.

    From your description of the symptoms I would guess that the layer 2 switch has both ASA ports in the same VLAN (which leads me to wonder if the layer 2 switch is doing any VLANs or are all ports in the native VLAN?). Can you provide details of how the layer 2 switch is configured?
    It also would help to know how the ISP is set up. You tell us that it is an Ethernet handoff. But you do not tell us whether the ISP  is handling that as a trunk with multiple VLANs or whether the ISP is treating it as an access port with a single VLAN. Can you clarify this?
    Knowing how the ISP is set up and how the layer 2 switch is configured will be critical in finding a solution that works for your ASA.
    HTH
    Rick

  • ARP Issue with Multiple Subnets

    We have a 4500-X as our core at our head office, connected to a Nexus 5K where our MS NLB Exchange cluster is (Virtualized).
    On the 4500-X there is a static MAC and static ARP entry for the NLB VIP.
    The servers are in VLAN 100 and the desktops are in VLAN 200
    No desktop can ping or access Exchange via the NLB virtual IP from VLAN 200 (or any other non-server VLAN) but can access each server individually.
    If I put a desktop in VLAN 100 I can access the VIP without a problem.
    All devices at sites across our MPLS-connected WAN can access Exchange without problem using the NLB VIP, as well as clients connecting via VPN.
    I can't figure out why remote sites, on different subnets can hit Exchange, but locally it doesn't work.
    As a note: We have another network at our head office that sits behind a firewall. Clients were not able to access the VIP until a static ARP entry was put on the firewall.
    Config is pretty straight forward.
    4500-X Config:
    VLAN 100
         name SERVER
    VLAN 200
         name DESKTOP
    interface VLAN100
         ip address 192.168.100.1 255.255.255.0
         no ip redirects
    interface VLAN200
         ip address 192.168.200.1 255.255.255.0
         no ip redirects
    mac address-table static 1111.1111.1111 vlan 100 interface Po1
    arp 192.168.100.100 1111.1111.1111 ARPA

    Hello.
    Could you draw a diagram of interconnections between 4500, MPLS and Exchange?
    Are you sure about MAC and port? Can you ping VIP address from 4500?

  • Show arp issue in 2960X

    Hi All,
    Our office network setup is ISP-------ASA---------3750---------2960X (stack by 4)-----------wired users
    Recently, I use command "show arp" in 2960X, the output as below,
    In arp table, I can't see wired PC mac address, and also I do a test at last,
    I filter my PC using my wired PC IP address (10.27.82.72), but no result in output.
    I just want to know what reason cause this issue?
    What should I to do that can solve this problem?
    Thanks in advance,
    swt001#sh arp
    Protocol  Address          Age (min)  Hardware Addr   Type   Interface
    Internet  10.25.2.222           172   0017.e048.de41  ARPA   Vlan48
    Internet  10.25.3.200           160   0017.e048.de41  ARPA   Vlan48
    Internet  10.25.31.25           236   0017.e048.de41  ARPA   Vlan48
    Internet  10.25.47.33           131   0017.e048.de41  ARPA   Vlan48
    Internet  10.25.48.50           256   0017.e048.de41  ARPA   Vlan48
    Internet  10.25.48.51           163   0017.e048.de41  ARPA   Vlan48
    Internet  10.27.36.101           46   0017.e048.de41  ARPA   Vlan48
    Internet  10.27.47.25           162   0017.e048.de41  ARPA   Vlan48
    Internet  10.27.82.5            236   0017.e048.de41  ARPA   Vlan48
    Internet  10.27.82.8            221   0017.e048.de41  ARPA   Vlan48
    Internet  10.27.82.15            30   0017.e048.de41  ARPA   Vlan48
    Internet  10.27.82.20           191   0017.e048.de41  ARPA   Vlan48
    Internet  10.27.82.21           209   0017.e048.de41  ARPA   Vlan48
    Internet  10.27.82.24           212   0017.e048.de41  ARPA   Vlan48
    Internet  10.27.82.37           128   0017.e048.de41  ARPA   Vlan48
    Internet  10.27.82.43           140   0017.e048.de41  ARPA   Vlan48
    Internet  10.27.82.49           186   0017.e048.de41  ARPA   Vlan48
    Internet  10.27.82.61            12   0017.e048.de41  ARPA   Vlan48
    Internet  10.27.82.63           229   0017.e048.de41  ARPA   Vlan48
    Internet  10.27.82.64            22   0017.e048.de41  ARPA   Vlan48
    Internet  10.27.82.69           245   0017.e048.de41  ARPA   Vlan48
    Internet  10.27.82.75            63   0017.e048.de41  ARPA   Vlan48
    Internet  10.27.82.91            80   0017.e048.de41  ARPA   Vlan48
    Internet  10.27.82.203          178   0017.e048.de41  ARPA   Vlan48
    Internet  10.27.95.61             -   2834.a26d.62c1  ARPA   Vlan48
    Internet  192.168.1.1             -   2834.a26d.62c2  ARPA   Vlan99
    swt001#
    swt001#sh arp | in 10.27.82.72
    swt001#

    Tracing a MAC address is fairly straight forward.
    #show mac-address-table 0017.e048.de41
    It may also be 
    #show mac address-table 0017.e048.de41
    This will list the Outgoing interface that the switch will use to forward frames destined for that MAC address. It does not automatically mean that interface HAS that MAC because it could be a trunk port.
    If the outgoing interface turns out to be a Trunk port, logon to the switch connected to that link and check its MAC table in the same way. Keep going until you reach the interface which has the MAC address you are looking for. It could be a virtual interface on a Switch/Router (SVI or Loopback), a Layer 3 address on a Router (i.e one with an IP address) or a normal host port.
    Hope that helps

  • Experincing issues with 2960X switch

    Hi there.
    We are experincing issues with 2960X switch losing the ability to recognise the modules that are inserted in SFP ports.
    Initially, the modules are recognised, usable and will happily participate in cross-stack etherchannels. However, after a period of time -  and this ranges from a couple of hours to a few days, the links go down on the 2960X-side but are still registered as up on at the other end of the etherchannel.
    2960X stack  1      Po1(SD)         LACP      Gi3/0/49(D) Gi3/0/51(D)
    3750G stack  2      Po2(SD)         LACP      Gi1/0/23(I) Gi2/0/22(I)
    When the link fails, the member switch loses the ability to identify modules inserted - it knows they are there, but it cannot identify them. Having a look at the controller for one of them and it's having trouble,see below:-
    sh controllers ethernet-controller gi3/0/49 phy detail
    GigabitEthernet3/0/49 (gpn: 457, port-number: 49)
    hulc_sfp_iic_intf_read_eeprom sfp _index 0 yeti_iic_read_retry fail
    hulc_sfp_iic_intf_read_eeprom sfp _index 0 yeti_iic_read_retry fail
    hulc_sfp_iic_intf_read_eeprom sfp _index 0 yeti_iic_read_retry fail
    A 'sh int' gives:-
    Auto-duplex, Auto-speed, link type is auto, media type is unknown.
    Reboot the stack or just the member and everything resets and works again - for a period of time. I've swapped from compatible to Cisco-brand modules inbetween restarts and it doesn't prevent the issue reoccuring.
    The slots all fail at the same time and once they're in the error state, that switch has to be restarted before it will recongnise anything inserted in any slot.
    I have this issue on two seperate stacks in two different sites. We're running 15.0(2)EX4.
    Has anyone seen anything like this? Particularly interested in this which I've seen using the sh controllers cmd and on the console once after a reboot. hulc_sfp_iic_intf_read_eeprom sfp _index 0 yeti_iic_read_retry fail
    Any thoughts would be greatly appreciated.
    Aid

    Hi Team
    We happen case GLC-T with Catalyst 2960 Hang , It can't work 
    We was reload switch but same ( GLC-T with Catalyst 2960 Hang)
    and use command bellow  
    Switch97#
    Switch97#
    Switch97#sh int gi 1/0/26 transceiver 5 transceiver de
    Switch97#sh int gi 1/0/25 transceiver detail 
    hulc_sfp_iic_intf_read_eeprom sfp _index 0 yeti_iic_read_retry fail
    hulc_sfp_iic_intf_read_eeprom sfp _index 0 yeti_iic_read_retry fail
    hulc_sfp_iic_intf_read_eeprom sfp _index 0 yeti_iic_read_retry failDiagnostic Monitoring is not implemented.
    Switch97#
    Switch97#
    Switch97#sh int gi 1/0/25 transceiver detail 6 transceiver        de
    Switch97#sh int gi 1/0/26 transceiver detail 
    hulc_sfp_iic_intf_read_eeprom sfp _index 1 yeti_iic_read_retry fail
    hulc_sfp_iic_intf_read_eeprom sfp _index 1 yeti_iic_read_retry fail
    hulc_sfp_iic_intf_read_eeprom sfp _index 1 yeti_iic_read_retry failDiagnostic Monitoring is not implemented.
    We try IOS Software EX3, EX4, EX5 and 15-2.2 but can't problem 
    Please suggest case to me

  • I have CS2 and would like to do Image Stacking.    I understand CS3 allows this.  correct?     Am I wiser to purchase CS3 upgrade.  Am I going to run into issues with install?

    I have CS2 and would like to do Image Stacking.    I understand CS3 allows this.  correct?     Am I wiser to purchase CS3 upgrade.  Am I going to run into issues with install?

    Well, I refuse to sign up to pay Adobe a monthly tribute for life too, but that doesn't mean we are limited to CS3.
    I'm staying with CS6.
    Adobe still sells a perpetual-license to Photoshop CS6 without the subscription model, but it's $700 for the Standard version and a cool $1,000 for the Extended version.
    You haven't mentioned your platform, Macintosh or Windows, so make sure CS3 or any other obsolete version you buy actually runs on a modern operating system.
    Good luck.

  • Mission Control/ Expose issue with stacked pages hard to view. Please help

    Is it just me or is there a real issue with the way Mission Control/ Expose displays these stacked windows? For instance, I had about 6 finder windows open, showing 6 different folders on my Desktop. If I then use Mission Control to quickly access a particular folder, it displays all my finder windows together, stacked up on one another and this makes it almost impossible to view which particular folder i want. It doesnt have the folder names displayed so this is seriuosly time consuming now. Is this something im doing wrong, or is it a valid issue?
    many thanks

    If you are just trying to see all the Finder windows which are available, just invoke App expose. I use a 4 finger swipe down. If you are in finder, just swipe. If you are in another application, hover your mouse over the Finder icon in the dock and swipe. All the windows are easy to see.
    (You can, of course, do this with any application, not just the Finder.)
    charlie

  • Are there any known issues with focus stacking or auto align causing PS to stop responding?

    Are there any known issues with focus stacking or auto align causing PS to stop responding?

    BOILERPLATE TEXT:
    Note that this is boilerplate text.
    If you give complete and detailed information about your setup and the issue at hand,
    such as your platform (Mac or Win),
    exact versions of your OS, of Photoshop (not just "CS6", but something like CS6v.13.0.6) and of Bridge,
    your settings in Photoshop > Preference > Performance
    the type of file you were working on,
    machine specs, such as total installed RAM, scratch file HDs, total available HD space, video card specs, including total VRAM installed,
    what troubleshooting steps you have taken so far,
    what error message(s) you receive,
    if having issues opening raw files also the exact camera make and model that generated them,
    if you're having printing issues, indicate the exact make and model of your printer, paper size, image dimensions in pixels (so many pixels wide by so many pixels high). if going through a RIP, specify that too.
    etc.,
    someone may be able to help you (not necessarily this poster, who is not a Windows user).
    a screen shot of your settings or of the image could be very helpful too.
    Please read this FAQ for advice on how to ask your questions correctly for quicker and better answers:
    http://forums.adobe.com/thread/419981?tstart=0
    Thanks!

  • 2960X stack with 3650G question

    Hello all,
    Please see attached file first.
    We have two existing Cisco 3650G with root/secondary bridge for resilience, now we want to add two Cisco 2960X with stack and for two server resilience with LACP, is it possible to do that ?
    Thanks

    Disclaimer
    The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
    Liability Disclaimer
    In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
    Posting
    The link between the secondary 3650G and your 2960X stack should block.

  • Five-Member 2960X Stack with 0.5-Meter Cables

    Hi can anyone help me with the proper way to connect a 3 and 5 member of 2960X stack, cause i just read the installation guide but only come the way to four member and i cant fine the logic to connnect 3 and 5 members.
    Regards!!!

    Hi Mate, thanks for me help me, im a little confuse withe the logic on the pattern that u send to me i im going to try to explain hope that im ok:
    SW 1 port 1 - SW 2 port 1
    SW 1 port 2 - SW 3 port 1
    SW 2 port 1 - SW 1 port 1
    SW 2 port 2 - SW 4 port 1
    SW 3 port 1 - SW 1 port 2
    SW 3 port 2 - SW 5 port 1
    SW 4 port 1 - SW 2 port 2
    SW 4 port 2 - SW 5 port 2
    SW 5 port 1 - SW 3 port 2
    SW 5 port 2 - SW 4 port 2
    Regards!

  • 2960X Stack Fails After reload Command

    Did not find anything in Bug Tool or these forums for this so posting as a new question.
    Environment is multiple stacks of  2960X -48FPD-L switches in different IDF's running IOS 15.0(2)EX5.   They were installed new and configured by another party about one month ago.  Current configuration is attached to this post.
    Switch stack fails to rebuild/sync after CLI reload command via telnet session.  IP stack appears to not initialize so no  network connectivity comes up even though per the onsite staff the master switch system LED's are green and one of the uplinks is connected to that switch..
    The system LED's of the other switches are amber.
    Remedy for the time being is for someone onsite to power cycle all the switches in 20 second master reelection window.
    Have not yet had opportunity to go onsite to console into one of the master switches to reload and monitor the process from that perspetive.
    One telltale that makes me wonder about EX5 is the reload command as documented in the 15.0(2)EX Switch Manager command reference here:
    http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst2960x/software/15-0_2_EX/stack_manager/command_reference/b_stck_152ex_2960-x_cr/b_stck_152ex_2960-x_cr_chapter_01.html#wp3486313748
    should prompt with,
    "Proceed to reload the whole Stack? [confirm]"
    but actually only prompts with,
    "Proceed with reload? [confirm]"
    as if the command was 'reload slot 1' instead of just 'reload'.
    I have not found anything in the config missing/wrong as far as configuration of the stack is concerned other than priorities and ID's were all assigned automatically/default..
    If EX5 is the issue I'm not keen on downgrading to EX3 because the uplinks are SFP-10G-LRM which had more issues with EX3 than with EX5.
    Thanks in advance for your time.
    Jon

    Have you tried cold booting the switch.  I know it is a horrible work around, but I ran circles around this problem on a switch I had upgraded (well- downgraded) from 15.2(3)E that was hitting this bug. Warm boots seemed to do nothing to clear the %ILET-1-AUTHENTICATION_FAIL: This switch may note have been manufactured by Cisco (so on so forth).  Once I pulled the power cable from the switch and waited several seconds prior to reapplying power, the switch came up cleanly.  Currently, Cisco has safe harbored 15.0(2a)EX5.  Did you happen to catch which bootloader combos with 15.0(2a)EX5 seemed to have the most consistent problems with this bug?  The campus I work at is currently in the process of rolling out about 120 of these switches and originally decided to stick with 15.0(2)EX5 until we hit an OIR with SFPs that TAC almost immediately acknowledged as a new development for that specific image. We as a group decided to try out 15.2(3)E and quickly found out that the bug still existed.  By that point, TAC was aware of the problem and over the weekend (2 days time after opening the ticket on a Friday if I remember right), 15.0(2a)EX5 was released.  
    Here is a small sampling of the switches that we have rolled out and what their bootloader + running IOS is.  Note: There are a few "stable" cases running 15.2(3)E, but they will be rolled back during maintenance windows in the next few weeks.  Everything that has been deployed since 15.0(2a)EX5 has been available has been running without issue on that IOS.   I don't know how useful this data is, but I can continue to build a list, though it looks like every switch that I have that is running 15.0(2)EX5 from the factory that is getting upgraded to 15.0(2a)EX5 has the 15.2(2r)E1 bootloader, with a few cases with the 15.0(2r)EX3 bootloader. 
    Does anyone have information on when an IOS upgrade will trigger a bootloader upgrade?  One thing I can't put a finger on right now is that during the last few rack/stack/configs of new stacks I have noticed that some of the switches running 15.0(2)EX5 from the factory that are being upgraded to 15.0(2a)EX5 are receiving a bootloader upgrade while the vast majority are not.

  • 2960x - stack cables connected while switches power on. SFP ports - status unknown

    Connected 2960x uplink using SFP ports both stacks and all 4 ports worked good.
    Remote tech connected last stack cable between first and last switch, in 2 different 2960x stacks of switches, while switches were  powered on. A longer stack cable was needed.  3 of 4 SFP ports did stopped communicating.
    One stack SFP stayed up in switch 2, not master.  Completed reload - other SPF connected in switch 4/0/52
    Second stack no connection on either SFP, remote tech power cycled switches.
    After power cycle one SFP worked  in Master 1/0/52, other switches SFP ports show "unknown" when inserting SFP.
    Configured port 48 on stack with issue and connected second uplink just fine.
    Has anyone experienced this with the SFP's?
    - GLC-T  P/N 30-1410-03
    Looking for documentation on reccommending procedure for connecting stack cables while switches should be powered off or not.
    Thanks,

    Opened Cisco TAC case.  the following bug was found.
    the two different HBRN's below require 2 different IOS and they cannot be in same stack.
     https://tools.cisco.com/bugsearch/bug/CSCur56395
    switch#sh ver | s Hardware Board
    Hardware Board Revision Number  : 0x05
    switch#remote command 2 sh ver | s Hardware Board
    Switch : 2 :------------ Hardware Board Revision Number  : 0x05
    switch#remote command 3 sh ver | s Hardware Board
    Switch : 3 : ------------ Hardware Board Revision Number  : 0x12
    switch#remote command 4 sh ver | s Hardware Board
    Switch : 4 :------------Hardware Board Revision Number  : 0x12
    From Cisco.
    Developers have recommended to upgrade the IOS version of switches with a Hardware Board revision Number below 0x10 to the release 15.0(2.0).EX5ES. this is the one attached to this email and should be applied to switch 1 and 2.
    For switches with a Hardware Board revision Number above 0x10 to the release 152-2.4.E1ES, which I will send you right away. This should be done on switch 3 and 4.
    Now, If you  load the engineering special, you will  need to do a full power-cycle (physically unplug the power and plug it back in for every single switch). A simple ‘reload’ will not resolve this.
    The same must be done on Switch-0. For this stack you will only need to load the image attached to this email since all the Hardware Board revision Numbers are lower than 0x10.
    done.

  • Issues with iMessage when switching data carrier (wifi - cellular)

    So I have had this issue with my 5S and now my 6+ in iMessage. Not *always* but often enough I've run into issues sending messages via iMessage when I associate with wifi in that they don't send. I'll get an error message saying "not delivered" and it will stack as many outgoing messages I try to send. However, if I force the first message to send as text, subsequent messages will go through afterwards without issue. If I go from wifi to cellular I have no issues whatsoever and when I have these issues on wifi, my data works fine (incoming emails, Facebook notifications, etc.). I used to run cellular data only because I had unlimited but now I have a cap so I intend on using wifi when possible...but to have to send my first message as a text just so I can use iMessage is annoying...

    Hi there BigDogg795,
    I would recommend taking a look at the troubleshooting steps for iMessage found in the article below. 
    iOS: Troubleshooting Messages - Apple Support
    To resolve issues with sending and receiving iMessages, follow these steps
    Check iMessage system status for current service issues.
    Go to Settings > Messages > Send & Receive and make sure that you registered iMessage with your phone number or Apple ID and that you selected iMessage for use. If the phone number or Apple ID isn't available for use, troubleshoot iMessage registration.
    Open Safari and navigate to www.apple.com to verify data connectivity. If a data connection isn't available, troubleshoot cellular data or a Wi-Fi connection.
    iMessage over cellular data might not be available while you're on a call. Only 3G and faster GSM networks support simultaneous data and voice calls. Learn which network your phone supports. If your network doesn't support simultaneous data and voice calls, go to Settings > Wi-Fi and turn Wi-Fi on to use iMessage while you're on a call.
    Restart your device.
    Tap Settings > General > Reset > Reset Network Settings on your iPhone.
    If you still can't send or receive an iMessage, follow these steps
    Make sure that the contact trying to message you isn't blocked in Settings > Messages > Blocked.
    Make sure that the contact you're trying to send a message to is registered with iMessage.
    If the issue occurs with a specific contact or contacts, back up or forward important messages and delete your current messaging threads with the contact. Create a new message to the contact and try again.
    If the issue occurs with a specific contact or contacts, delete and recreate the contact in the Contacts app. Create a new message to the newly created contact and try again.
    Back up and restore your device as new.
    -Griff W.

  • Issue with xsd Data type mapping for collection of user defined data type

    Hi,
    I am facing a issue with wsdl for xsd mapping for collection of user defined data type.
    Here is the code snippet.
    sample.java
    @WebMethod
    public QueryPageOutput AccountQue(QueryPageInput qpInput)
    public class QueryPageInput implements Serializable, Cloneable
    protected Account_IO fMessage = null;
    public class QueryPageOutput implements Serializable, Cloneable
    protected Account_IO fMessage = null;
    public class Account_IO implements Serializable, Cloneable {
    protected ArrayList <AccountIC> fintObjInst = null;
    public ArrayList<AccountIC>getfintObjInst()
    return (ArrayList<AccountIC>)fintObjInst.clone();
    public void setfintObjInst(AccountIC val)
    fintObjInst = new ArrayList<AccountIC>();
    fintObjInst.add(val);
    Public class AccountIC
    protected String Name;
    protected String Desc;
    public String getName()
    return Name;
    public void setName(String name)
    Name = name;
    For the sample.java code, the wsdl generated is as below:
    <?xml version="1.0" encoding="UTF-8" ?>
    <wsdl:definitions
    name="SimpleService"
    targetNamespace="http://example.org"
    xmlns:wsdl="http://schemas.xmlsoap.org/wsdl/"
    xmlns:tns="http://example.org"
    xmlns:xsd="http://www.w3.org/2001/XMLSchema"
    xmlns:mime="http://schemas.xmlsoap.org/wsdl/mime/"
    xmlns:soap="http://schemas.xmlsoap.org/wsdl/soap/"
    xmlns:soap12="http://schemas.xmlsoap.org/wsdl/soap12/"
    >
    <wsdl:types>
    <xs:schema version="1.0" targetNamespace="http://examples.org" xmlns:ns1="http://example.org/types"
    xmlns:xs="http://www.w3.org/2001/XMLSchema">
    <xs:import namespace="http://example.org/types"/>
    <xs:element name="AccountWSService" type="ns1:accountEMRIO"/>
    </xs:schema>
    <xs:schema version="1.0" targetNamespace="http://example.org/types" xmlns:ns1="http://examples.org"
    xmlns:tns="http://example.org/types" xmlns:xs="http://www.w3.org/2001/XMLSchema">
    <xs:import namespace="http://examples.org"/>
    <xs:complexType name="queryPageOutput">
    <xs:sequence>
    <xs:element name="fSiebelMessage" type="tns:accountEMRIO" minOccurs="0"/>
    </xs:sequence>
    </xs:complexType>
    <xs:complexType name="accountEMRIO">
    <xs:sequence>
    <xs:element name="fIntObjectFormat" type="xs:string" minOccurs="0"/>
    <xs:element name="fMessageType" type="xs:string" minOccurs="0"/>
    <xs:element name="fMessageId" type="xs:string" minOccurs="0"/>
    <xs:element name="fIntObjectName" type="xs:string" minOccurs="0"/>
    <xs:element name="fOutputIntObjectName" type="xs:string" minOccurs="0"/>
    <xs:element name="fintObjInst" type="xs:anyType" minOccurs="0" maxOccurs="unbounded"/>
    </xs:sequence>
    </xs:complexType>
    <xs:complexType name="queryPageInput">
    <xs:sequence>
    <xs:element name="fPageSize" type="xs:string" minOccurs="0"/>
    <xs:element name="fSiebelMessage" type="tns:accountEMRIO" minOccurs="0"/>
    <xs:element name="fStartRowNum" type="xs:string" minOccurs="0"/>
    <xs:element name="fViewMode" type="xs:string" minOccurs="0"/>
    </xs:sequence>
    </xs:complexType>
    </xs:schema>
    <schema xmlns="http://www.w3.org/2001/XMLSchema" targetNamespace="http://example.org"
    xmlns:xsd="http://www.w3.org/2001/XMLSchema" xmlns:tns="http://example.org" xmlns:ns1="http://example.org/types">
    <import namespace="http://example.org/types"/>
    <xsd:complexType name="AccountQue">
    <xsd:sequence>
    <xsd:element name="arg0" type="ns1:queryPageInput"/>
    </xsd:sequence>
    </xsd:complexType>
    <xsd:element name="AccountQue" type="tns:AccountQue"/>
    <xsd:complexType name="AccountQueResponse">
    <xsd:sequence>
    <xsd:element name="return" type="ns1:queryPageOutput"/>
    </xsd:sequence>
    </xsd:complexType>
    <xsd:element name="AccountQueResponse" type="tns:AccountQueResponse"/>
    </schema>
    </wsdl:types>
    <wsdl:message name="AccountQueInput">
    <wsdl:part name="parameters" element="tns:AccountQue"/>
    </wsdl:message>
    <wsdl:message name="AccountQueOutput">
    <wsdl:part name="parameters" element="tns:AccountQueResponse"/>
    </wsdl:message>
    <wsdl:portType name="SimpleService">
    <wsdl:operation name="AccountQue">
    <wsdl:input message="tns:AccountQueInput" xmlns:ns1="http://www.w3.org/2006/05/addressing/wsdl"
    ns1:Action=""/>
    <wsdl:output message="tns:AccountQueOutput" xmlns:ns1="http://www.w3.org/2006/05/addressing/wsdl"
    ns1:Action=""/>
    </wsdl:operation>
    </wsdl:portType>
    <wsdl:binding name="SimpleServiceSoapHttp" type="tns:SimpleService">
    <soap:binding style="document" transport="http://schemas.xmlsoap.org/soap/http"/>
    <wsdl:operation name="AccountQue">
    <soap:operation soapAction=""/>
    <wsdl:input>
    <soap:body use="literal"/>
    </wsdl:input>
    <wsdl:output>
    <soap:body use="literal"/>
    </wsdl:output>
    </wsdl:operation>
    </wsdl:binding>
    <wsdl:service name="SimpleService">
    <wsdl:port name="SimpleServicePort" binding="tns:SimpleServiceSoapHttp">
    <soap:address location="http://localhost:7101/WS-Project1-context-root/SimpleServicePort"/>
    </wsdl:port>
    </wsdl:service>
    </wsdl:definitions>
    In the above wsdl the collection of fintObjInst if of type xs:anytype. From the wsdl, I do not see the xsd mapping for AccountIC which includes Name and Desc. Due to which, when invoking the web service from a different client like c#(by creating proxy business service), I am unable to set the parameters for AccountIC. I am using JAX-WS stack and WLS 10.3. I have already looked at blog http://weblogs.java.net/blog/kohlert/archive/2006/10/jaxws_and_type.html but unable to solve this issue. However, at run time using a tool like SoapUI, when this wsdl is imported, I am able to see all the params related to AccountIC class.
    Can some one help me with this.
    Thanks,
    Sudha.

    Did you try adding the the XmlSeeAlso annotation to the webservice
    @XmlSeeAlso({<package.name>.AccountIC.class})
    This will add the schema for the data type (AccountIC) to the WSDL.
    Hope this helps.
    -Ajay

  • EXCEPTION_ACCESS_VIOLATION issue with regard to OpenGL

    EXCEPTION_ACCESS_VIOLATION issue with OpenGL occurring with the Java SE Runtime Environment 6u17 on Windows 7, 32 & 64 bit platforms.   Version 6u24 and later does not produce the crash. However, we cannot use any other version of JRE other than 6u17 due to customer constraints. The two primary scenarios where crash  (jvm exits) occurs are: 1) toggling between two applications then selecting an image item on screen ( OpenGL rendering takes place)... (Log file: hs_err_pid6568_C2_TC_error.log). Scenario 2: When panning an image (OpenGL rendering takes place) and then clicking a button to load additional image data (OpenGL rendering takes place), crash occurs (Log file: hs_err_pid6036_ENR_TERRAIN_crash.log)
    Is there any Oracle documentation noting any JRE fixes between 6u17 and 6u24 that might at least mitigate the issue(s) described above? Or information with regard to issues between JRE's and OpenGL ? Also, if anyone can advise on code mods, etc that we can try toward said mitigation efforts of course would be helpful.
    The following snippet hopefully should suffice as general example for both noted issues:
    Log snippet ( hs_err_pid6568_C2_TC_error.log):
    # A fatal error has been detected by the Java Runtime Environment:
    #  EXCEPTION_ACCESS_VIOLATION (0xc0000005) at pc=0x6ec158d6, pid=6568, tid=7176
    # JRE version: 6.0_17-b04
    # Java VM: Java HotSpot(TM) Client VM (14.3-b01 mixed mode windows-x86 )
    # Problematic frame:
    # C  [GLU32.dll+0x58d6]
    # If you would like to submit a bug report, please visit:
    #   http://java.sun.com/webapps/bugreport/crash.jsp
    # The crash happened outside the Java Virtual Machine in native code.
    # See problematic frame for where to report the bug.
    ---------------  T H R E A D  ---------------
    Current thread (0x4d996000):  JavaThread "pool-6-thread-1" [_thread_in_native, id=7176, stack(0x502b0000,0x50300000)]
    siginfo: ExceptionCode=0xc0000005, reading address 0x00000028
    Registers:
    EAX=0x00179ca0, EBX=0x00179ce8, ECX=0x00179ca0, EDX=0x5691e9a0
    ESP=0x502ff4ac, EBP=0x502ff4cc, ESI=0x00000000, EDI=0x00179ca0
    EIP=0x6ec158d6, EFLAGS=0x00010246
    Top of Stack: (sp=0x502ff4ac)
    0x502ff4ac:   6ec13548 001833f8 0018e060 0018e018
    0x502ff4bc:   00179ca0 00000000 00000018 502ff4f0
    0x502ff4cc:   502ff4f0 6ec165a8 001a5038 0018e048
    0x502ff4dc:   0018e018 001cd728 6ec147d7 001cd728
    0x502ff4ec:   001a5038 502ff514 6ec14925 2e5096af
    0x502ff4fc:   5f338d35 5038bf30 001a5038 001a5038
    0x502ff50c:   02e177c2 0016b930 502ff534 6ec12c65
    0x502ff51c:   001a5038 5038bf30 0000001d 001a5038
    Instructions: (pc=0x6ec158d6)
    0x6ec158c6:   30 dc 61 30 eb e7 dd db dd d9 dd d8 c3 dd 41 28
    0x6ec158d6:   dc 66 28 dd 42 28 dc 61 28 d9 c0 d8 c2 d9 ee d8
    Stack: [0x502b0000,0x50300000],  sp=0x502ff4ac,  free space=317k
    Native frames: (J=compiled Java code, j=interpreted, Vv=VM code, C=native code)
    C  [GLU32.dll+0x58d6]
    C  [GLU32.dll+0x65a8]
    C  [GLU32.dll+0x4925]
    C  [GLU32.dll+0x2c65]
    C  [pep_gx.dll+0x3dc8]
    Java frames: (J=compiled Java code, j=interpreted, Vv=VM code)
    j  com.cimmeria.efb.crom.tc.cmn.jni.ChartRendererNative.nativeGetRenderedChart(Lcom/cimmeria/efb/crom/common/utility/ILogUtility;Lcom/cimmeria/efb/crom/common/jni/JNIErrorInfo;Lcom/cimmeria/efb/crom/tc/cmn/jni/IChartImageProxy;IFZI)V+0
    j  com.cimmeria.efb.crom.tc.cmn.jni.ChartRendererNative$RenderCallable.call_aroundBody2(Lcom/cimmeria/efb/crom/tc/cmn/jni/ChartRendererNative$RenderCallable;Lorg/aspectj/lang/JoinPoint;)Ljava/lang/Object;+51
    j  com.cimmeria.efb.crom.tc.cmn.jni.ChartRendererNative$RenderCallable.call_aroundBody3$advice(Lcom/cimmeria/efb/crom/tc/cmn/jni/ChartRendererNative$RenderCallable;Lorg/aspectj/lang/JoinPoint;Lcom/cimmeria/efb/crom/tc/cmn/aop/RuntimeExceptionAndErrorMonitorAspect;Lorg/aspectj/runtime/internal/AroundClosure;Lorg/aspectj/lang/JoinPoint;)Ljava/lang/Object;+14
    j  com.cimmeria.efb.crom.tc.cmn.jni.ChartRendererNative$RenderCallable.call()Ljava/lang/Object;+34
    j  java.util.concurrent.FutureTask$Sync.innerRun()V+30
    j  java.util.concurrent.FutureTask.run()V+4
    J  java.util.concurrent.ThreadPoolExecutor$Worker.runTask(Ljava/lang/Runnable;)V
    j  java.util.concurrent.ThreadPoolExecutor$Worker.run()V+28
    j  java.lang.Thread.run()V+11
    v  ~StubRoutines::call_stub

    There are some other solutions possible.
    1. Get another driver. The only one known is java only so it wont crash. But is not not free.
    2. Use a proxy driver. That means that another app actually does the database work. If it crashes you just start it again (which you can do in your main code.) That way it won't take down your server. There are commercial jdbc drivers that claim MS Access but are are really just proxy implementations as an option in this area.

Maybe you are looking for